Datalogic Scanning DS4600A-2XX5, DS4600A-XXX0 User Manual

A

General View: Laser Safety:

12

1

11

DS4600A - 2XXX Models

2

4

10

DS4600A - 3XXX Models

Figure A

Cable with 25-pin Connector

1

Laser Beam Output Window

2

ccessory Mounting Holes

3

Warning Label

4

Mounting Holes

5

Data TX LED

6

External Trigger LED

7
8

Good Read LED
Ready LED

9

Warning and Classification Labels

10

Keypad

11

Display

12

For further details on product installation, see the
complete Installation Manual available on the WinHost
CD included with this product.

Power Supply:

- This product is intended to be installed by Qualified
Personnel only.

- Models DS4600A-XXX0:

This device is intended to be supplied by a UL Listed
Direct Plug-in Power Unit marked “Class 2”, rated 10-30
V minimum, 0.60 A.
This device may also be supplied by a UL Listed Power
Unit marked “Class 2” or LPS power source which
supplies power directly to the scanner via the 25-pin
connector.

- Model DS4600A-2XX5:

This device is intended to be supplied by a UL Listed
Direct Plug-in Power Unit marked “Class 2”, rated 24 V
minimum, 0.50 A.
This device may also be supplied by a UL Listed Power
Unit marked “Class 2” or LPS power source which
supplies power directly to the scanner via the 25-pin
connector.

WEEE Compliance:

The scanner is classified as a Class 2 laser
product according to EN 60825-1 regulations
and as a Class II laser product according to
CDRH regulations.

For installation, use and maintenance it is not
necessary to open the device.

There is a safety device which allows the
laser to be switched on only if the motor is
rotating above the threshold for its correct

3

scanning speed.

The laser beam can be switched off through a
software command (see also the WinHost
Help On-Line).

AVOID EXPOSURE

LASER LIGHT IS EMITTED

FROM THIS APERTURE

CAUTION-CLASS 3B

LASER LIGHT

2

WHEN OPEN

AVOID

EXPOSURE TO BEAM

DATALOGIC S.p.A. Via Candini, 2
40012 LIPPO DI CALDERARA (BO) ITALY

Model No. Serial No.

Volt Amp.

Manufactured

This product conforms to the applicable requirements of
21CFR1040 at the date of manufacture.

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

MAXIMUM OUTPUT RADIATION 1 mW
EMITTED WAVE LENGTH 630~680 nm

Warning and device class labels

The laser diode used in this device is classified
as a class 3B laser product according to EN
60825-1 regulations and as a Class IIIb laser
product according to CDRH regulations. As it is
not possible to apply a classification label on
the laser diode used in this device, the
following label is reproduced below.

AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT

MAX. OUTPUT RADIATION 30 mW

EMITTED WAVE LENGTH 630~680 nm

Laser diode class label

Any violation of the optic parts in particular
can cause radiation up to the maximum level
of the laser diode (30 mW at 630 to 680 nm).

DS4600A QUICK GUIDE

LASER LIGHT

TO EN 60825-1 (2001)

LASER LIGHT

TO EN 60825-1 (2001)

2

V

Model Description:

DS4600A QUICK GUIDE

DS4600A - X X X X

Decoding Mode

= Standard w/ Display

3 = Advanced Code Reconstruction

Reading Range

0 = Medium Range
1 = Long Range
2 = Short Range

Optic

ersion

0 = Linear
1 = Raster R1
2 = Raster R2

Special Features

0 = Standard
5 = Integrated Heater

The following table displays each version’s reading performance.

Version Reading Distance

Max Code Resolution

mm (mils)

210X 200 mm (8 in) - 980 mm (39 in) on 1.00 mm (40 mils) codes 0.50 (20) 800
200X 160 mm (6 in) - 540 mm (21 in) on 0.50 mm (20 mils) codes 0.25 (10) 800
220X 50 mm (1.97 in) - 400 mm (15.75 in) on 0.80 mm (31 mils) codes 0.20 (8) 800
310X 200 mm (8 in) - 970 mm (38 in) on 1.00 mm (40 mils) codes 0.50 (20) 800
300X 160 mm (6 in) - 540 mm (21 in) on 0.50 mm (20 mils) codes 0.25 (10) 800
320X 120 mm (4.7 in) - 310 mm (12.2 in) on 0.30 mm (12 mils) codes 0.20 (8) 800

Technical Features:

ELECTRICAL FEATURES SOFTWARE FEATURES
Power Supply

Model XXX0: 10 –30 Vdc
Model 2XX5: 24 Vdc

Power Consumption
max.
Main Serial Interface

Model XXX0: 6W
Model 2XX5: 12W
RS232;
RS485 Full-Duplex
RS485 Half-Duplex

Auxiliary Interface
Baudrates
Inputs
External Trigger, IN1,

RS232
1200 to 115200

(optocoupled NPN or PNP)

IN2
Voltage max.
Current Consumption
max.
Outputs

OUT1, OUT2
V

max.

CE

Collector Current
max.
VCE Saturation

Power Dissipation
max.

30 Vdc
25 mA

(optocoupled OE or OC)
40 Vdc

40 mA continuous;
130 mA pulsed
1V at 10 mA max.

90 mW at 40 °C
(Ambient temp.)

OPTICAL FEATURES Temperature
Light Source
Wavelength
Safety Class

Semiconductor laser diode
630 to 680 nm
Class 2 - EN 60825-1; CDRH

USER INTERFACE Vibration Resistance
LED Indicators

Ready, Good Read, IEC 68-2-6 test FC 1.5 mm @ 13 to 55 Hz
External Trigger,
Data TX

PHYSICAL FEATURES Shock Resistance
Dimensions
Weight

101x84x42 mm

(22 oz)

615 g.

(4x3.3x1.7 in) IEC 68-2-27 test EA 3 shocks on each axis

Readable Codes

EAN/UPC (including Add-on 2
and Add-on 5)
Code 39
2/5 Interleaved
Code 128
EAN 128
Code 93
Codabar

Headers and
Terminators

Operating Modes

Configuration Modes

Pharmacode

Up to four header and four
terminator characters

On-Line, Automatic,
Serial-On-Line, Test
Through menus using
WinHost utility
Host Mode (commands from

Code Selection

Parameter Storage

one of the serial ports)
Up to six different codes
during one reading phase

Non-volatile internal
EEPROM

ENVIRONMENTAL FEATURES
Operating

0° to 40 °C (32° to 104 °F)
2XX5: -30° (-22 °F) to 40 °C

Storage
Temperature
Humidity max

-20° to 70 °C (-4° to 158 °F)

90% non condensing
14 mm @ 2 to 10 Hz

2 g @ 70 to 200 Hz
2 hours on each axis

30g; 11 ms;

Protection Class

IP65

Speed

scans/s

2

DS4600A QUICK GUIDE

Accessories:

Name Description Part Number

C-BOX 100/200 Connection Box 93ACC1510, 93ACC1520
C-BOX 300/310 Connection Box Profibus 93A301000, 93A301030
C-BOX 400/410 Connection Box DeviceNet 93A301010, 93A301040
GFC-41 90° Reading Device 91D081000
OM4000 Oscillating Mirror 93A251030
INT-30 (for C-Box 100) 20 mA Current Loop Interface Board 93A151022

Electrical Connections:

DS4600A is equipped with a cable terminated by a 25-pin female D-sub connector for connection to the power
supply and input/output signals.

Do not connect GND and SGNDs (Main or Aux) to different (external) ground references.
GND and SGNDs (Main and Aux) are internally connected through filtering circuitry which

CAUTION

The details of the connector pins are indicated in the following table:

can be permanently damaged if subjected to voltage drops over 0.8 Vdc.

25-pin D-sub female connector pinout

Pin Name Function

13 VS Power supply input voltage +
25 GND Power supply input voltage -

1 CHASSIS Chassis Ground

9 VS External Trigger supply voltage +
18 EXT TRIG+ External Trigger +
19 EXT TRIG- External Trigger -

6 IN1+ Input 1 +
10 IN1- Input 1 ­14 IN2+ Input 2 +
15 IN2- Input 2 -

8 OUT1 + Output 1 +
22 OUT1- Output 1 ­11 OUT2 + Output 2 +
12 OUT2- Output 2 ­20 RXAUX Auxiliary RS232
21 TXAUX Auxiliary RS232
23 SGND Aux Signal Ground Auxiliary interface
24 GND Power Supply Voltage ­16 Reserved
17 Reserved

Pin RS232

2 TX232 TX485+ RTX485+

3 RX232 RX485+

4 RTS232 TX485- RTX485-

5 CTS232 RX485-

7 SGND Main SGND Main SGND Main

RS485

Full-Duplex

25-pin female connector

RS485

Half-Duplex

3

Mechanical Installation:

DS4600A QUICK GUIDE

22*

0.86

41.8

10

0.39

1.64

81

3.19

M4 N° 4

0.46

11.8

37

5

1.47

0.2

0.32

8.25

87.9

3.46

Mounting hole depth M4 X 5

20.2

0.8

37

1.46

42

1.65

* The quote refers to the scan line

Overall dimensions for 2XXX Models

Input/Output Connections:

DS4600A 25-pin

8/11

C

12/22

E

Output open collector connections

V

max = 40 Vdc

CE

I max = 40 mA continuous

DS4600A 25-pin

+ 5V

Open Collector

+

-

Vext 30 Vdc max.

18/6/14

19/10/15

+

-

USER INTERFACE

NPN NPN

USER INTERFACE

20

2.28

1.28

0.79

1.55

39.4

101

3.98

18

0.70

14.8

0.58
M4 N°2

58

32.5

3.75

0.15

Vext 40 Vdc max.

V

Signal

0.90

18*

0.71

20.2

83.5

3.29

37

1.46

DS4600A

23

14.8

0.58

0.8

42

1.65

* The quote refers to the scan line

M4 N°2

58

2.28

1.28

32.5

3.75

0.15

20

0.79

83.5

3.29

1.55

39.4

101

3.98

18

0.70
23

0.90

Overall dimensions for 3XXX Models

5.5

0.22

115

4.53

5

0

.

57.3

2.26

.

5

2

2

5

.

5

2

2

.

0

35°

1

0

°

5

0.20

5.5

0.22

39

1.54

3

0.12

Mounting Bracket Dimensions

DS4600A 25-pin

+ 5V

9

18/6/14

19/10/15

25

USER INTERFACE

VS

+

-

GND

V

Ground

Signal

DS4600A 25-pin

+ 5V

4

Input NPN command using external power

PNP

PNP

Vext 30 Vdc max.

18/6/14

19/10/15

+

-

Input PNP command using external power

USER INTERFACE

V

Ground

Signal

Input NPN command using DS4600A power

VS

+

-

GND

USER INTERFACE

V

Ground

DS4600A 25-pin

+ 5V

9

18/6/14

19/10/15

25

Input PNP command using DS4600A power

Signal