Datalogic BC9XX0-STAR Quick Reference Manual

BC9XX0-STAR

Base Station/Charger

Quick Reference Guide

Datalogic ADC, Inc.

959 Terry Street
Eugene, OR 97402
USA
Telephone: [phone]
Fax: [phone]

©2013-2014 Datalogic, Inc.

An Unpublished Work - All rights reserved. No part of the contents of this docu­mentation or the procedures described therein may be reproduced or transmitted
in any form or by any means without prior written permission of Datalogic ADC,
Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”). Owners of Data­logic products are hereby granted a non-exclusive, revocable license to reproduce
and transmit this documentation for the purchaser's own internal business pur­poses. Purchaser shall not remove or alter any proprietary notices, including copy­right notices, contained in this documentation and shall ensure that all notices
appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed ver­sions by contacting your Datalogic representative. Electronic versions may either
be downloadable from the Datalogic website (www.datalogic.com) or provided on
appropriate media. If you visit our website and would like to make comments or
suggestions about this or other Datalogic publications, please let us know via the
"Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual
that is complete and accurate, however, Datalogic reserves the right to change any
specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in
many countries, including the U.S.A. and the E.U. All other brand and product
names may be trademarks of their respective owners.

Patents

See www.patents.datalogic.com

for patent list.

This product is covered by one or more of the following patents:

Utility patents: US7948214, EP1873886B1, ZL200780030808.2

Quick Reference Guide i

Table of Contents

END USER LICENSE AGREEMENT .................................................................iii

Software Product Policy ..................................................................................v

Customers Under Software Support .....................................................v

Using the BC9xx0 Base Station ..................................................................... 1

Installation ....................................................................................................... 2

Mounting the BC9xx0 Cradle ......................................................................... 2

Mounting Brackets ................................................................................. 2

To change the Bracket:................................................................... 3

Permanent Mounting ............................................................................. 4

Mounting for Portable Use .................................................................... 4

Mounting the Metal Plate.............................................................. 4

Attaching the Metal Plate to Base................................................ 5

System Connections ....................................................................................... 6

BC9x80 models - Ethernet Connection ................................................ 6

Ferrite Clamp Filter......................................................................... 6

Non-Ethernet Connection ...................................................................... 7

Connecting and Disconnecting the Multi-Interface Cable ......... 7

Configuration ................................................................................................... 8

BC9x80 Ethernet Models ....................................................................... 8

Non-Ethernet Models ............................................................................ 8

Datalogic Aladdin™.......................................................................... 8

Serial Configuration ........................................................................ 8

Configuration Bar Codes ................................................................ 9

Selecting the Interface Type .......................................................................... 9

Configuring the Interface ....................................................................... 9

Ethernet Interface (BC9x80 Models only)..................................... 9

RS-232 ........................................................................................... 10

USB................................................................................................. 11

Keyboard Interface ....................................................................... 12

Scancode Tables............................................................................ 13

Country Mode ........................................................................................ 14

Caps Lock State ..................................................................................... 18

Numlock ................................................................................................. 19

Resetting Standard Product Defaults ................................................ 20

Compatibility with the PowerScan™ 8000 family .............................. 20

Technical Features ........................................................................................ 21

Regulatory Information ................................................................................ 23

Compliance ............................................................................................ 23

Power Supply ......................................................................................... 23

FCC Compliance ..................................................................................... 23

ii BC 9xx0 Cradle

Radio Compliance.......................................................................... 23

China RoHS Statement................................................................. 24

WEEE Compliance .................................................................................25

Datalogic ADC Limited Factory Warranty ................................................... 26

Ergonomic Recommendations .................................................................... 27

Services and Support ....................................................................................28

Products......................................................................................... 28

Service & Support.......................................................................... 28

Contact Us...................................................................................... 28

Quick Reference Guide iii

Datalogic ADC, Inc.

PowerScan™ 9500 PRODUCT SERIES

END USER LICENSE AGREEMENT

Notice to End User: The Datalogic Product you have acquired contains embedded Software, which is integral to
the product's operation. This Software is being provided to you under license, subject to the terms and condi­tions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and
conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, Datalogic is not
willing to license the Software to you, you may not use the Datalogic Product or the Software, and you must
contact the party from whom you acquired the Datalogic Product for instructions.

END USER LICENSE AGREEMENT TERMS:

This End User Software License Agreement ("Agreement") is a legally binding agreement governing the licens­ing of the Software and Documentation by Datalogic ADC, Inc. and its Affiliates ("Datalogic") to the entity or
person who has purchased or otherwise acquired a Datalogic Product ("End User"). For purposes of this Agree­ment, any software that is associated with a separate end-user license agreement is licensed to you under the
terms of that license agreement. Datalogic and End User hereby agree as follows:

1. Definitions

1.1 "Affiliate" means a business entity currently existing or later acquired that controls, is controlled by, or is
under common control with Datalogic S.p.A.

1.2 "Documentation" means materials such as user's guides, program reference guides, quick reference guides,
manuals, or similar materials associated with or related to the Datalogic Product, whether in printed,
"online", or other form.

1.3 "Proprietary Information" means: (a) source code, object code, software, documentation, and any related
internal design, system design, data base design, algorithms, technology, technical data or information,
implementation techniques, and trade secrets related to the Software, (b) any other trade secrets marked
appropriately or identified as proprietary or confidential, and (c) any information that End User, under the
circumstances, should recognize as confidential. Proprietary Information does not include any informa­tion that the receiving party can establish was (1) in the public domain, (2) already in the receiving party's
possession or rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of
any other's proprietary rights, or (4) independently developed without access to Proprietary Information.

1.4 "Datalogic Product" means the Datalogic® Powerscan™ series scanner product, including all embedded
Software in and all Documentation related to such product, which has been purchased or otherwise
acquired by End User, whether obtained directly or indirectly from Datalogic.

1.5 "Software" means any software or computer programs of Datalogic or its third party licensors in machine
readable form which is embedded in the Datalogic Product, whether obtained directly or indirectly from
Datalogic, including any replacement, update, upgrade, enhancement or modification.

2. Scope Of License Granted

2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to use the Software,
solely on the Datalogic Product in which it is embedded ("designated Datalogic Product"), in machine­readable form only, solely for End User's internal business purposes. This Agreement does not convey
ownership of the Software to End User. Title to the Software shall be and remain with Datalogic or the
third party from whom Datalogic has obtained a licensed right. As used in this Agreement, the term "pur­chase" or its equivalents when applied to the Software shall mean "acquire under license." End User is not
entitled to receipt or use of the source code to any Software.

2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or
remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend,
rent, give, or otherwise transfer the Software to any other person or organization, for purposes other than
as expressly provided in this Agreement, without Datalogic's prior written consent.

3. Transfers, Support

3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use
of the Software on other than the designated Datalogic Product will be a material breach of this Agree­ment. However, Datalogic may elect not to terminate this Agreement or the granted licenses, but instead
may elect to notify End User that End User is deemed to have ordered and accepted a license for each
breaching use. End User shall pay Datalogic the applicable list price for such licenses as of the date of
such breach.

3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Datalogic
Product to any third party unless such third party agrees with Datalogic in writing to be bound by the
terms and conditions of this Agreement. Any such transfer of the Datalogic Product absent such agree­ment shall be null and void.

3.3 End User may obtain support for Software from Datalogic at Datalogic's standard support fees and under
Datalogic's standard support terms and conditions in effect at the time the support is requested.

4. Intellectual Property

End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic's third
party licensors and that the Software is protected by intellectual property laws and treaties. The license set
forth in this Agreement does not transfer to End User any ownership of Datalogic's or its third party licensors'
copyrights, patents, trademarks, service marks, trade secrets, or other intellectual property rights and End
User shall have no right to commence any legal actions to obtain such rights. End User shall not remove, mod­ify, or take any other action that would obscure any copyright, trademark, patent marking, or other intellectual
property notices contained in or on the Datalogic Product.

END USER LICENSE AGREEMENT

iv BC 9xx0 Cradle

5. Proprietary Information

5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret
property of Datalogic and Datalogic's third party licensors and End User acquires no right or interest in any
Proprietary Information.

5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Information of Datalogic
or its third party licensors to any person other than End User's authorized employees or agents who are
under confidentiality agreement, and End User shall not use the Proprietary Information other than in
conjunction with use of the Datalogic Product exclusively for End User's internal business purposes. End
User shall take steps to protect the Proprietary Information no less securely than if it were End User's own
intellectual property.

5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the
termination of this Agreement.

6. Limited Warranty

6.1 Datalogic warrants that, under normal use and operation, the Datalogic Product will conform substantially
to the applicable Documentation for the period specified in the Documentation. During this period, for all
reproducible nonconformities for which Datalogic has been given written notice, Datalogic will use com­mercially reasonable efforts to remedy nonconformities verified by Datalogic. End User agrees to supply
Datalogic with all reasonably requested information and assistance necessary to help Datalogic in reme­dying such nonconformities. For all defects reported to Datalogic within the warranty period, Datalogic's
liability is limited to providing End User with one copy of corrections or responding to End User's problem
reports according to Datalogic's standard assistance practices. Datalogic does not warrant that the prod­uct will meet End User's requirements or that use of the product will be uninterrupted or error free, or that
Datalogic's remedial efforts will correct any nonconformance. This limited warranty does not cover any
product that have been subjected to damage or abuse, whether intentionally, accidentally, or by neglect, or
to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product,
uses the product in any manner other than as established in the Documentation, or if End User breaches
any of the provisions of this Agreement.

6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PROVIDED "AS IS" AND DATA­LOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT
TO THE PRODUCT, AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.

7. Infringement

7.1 Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished here­under infringe a United States patent or copyright of a third party and Datalogic will pay any damages
finally awarded against End User by a court of competent jurisdiction that are attributable to such claim
or will pay End User's part of any settlement that is attributable to such claim, provided, that 1) End User
notifies Datalogic promptly in writing of the claim, 2) Datalogic controls the defense or settlement of the
claim, and 3) End User cooperates fully with Datalogic in such defense or settlement. All notices of a claim
should be sent to Datalogic ADC, Inc., Legal Department, 959 Terry Street, Eugene, OR 97402.

7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for End User the
right to continue using the Datalogic Product, 2) modify the Datalogic Product so that it becomes non­infringing, 3) replace the Datalogic Product with an equivalent product not subject to such claim, or 4) pro­vide End User an opportunity to return the Datalogic Product and receive a refund of the purchase price
paid, less a reasonable allowance for use.

7.3 Datalogic shall have no liability to End User for claims of infringement based upon 1) the use of any Data­logic Product in combination with any product which Datalogic has not either furnished or authorized for
use with such Datalogic Product 2) the use of any Datalogic Product designed, manufactured, or modified
to the specifications of End User, or 3) End User's modification of the Datalogic Product without written
authorization from Datalogic.

7.4 THE FOREGOING STATES DATALOGIC'S COMPLETE AND ENTIRE OBLIGATION CONCERNING CLAIMS OF
PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS AND SUPERCEDES
ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH
CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE
AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET
FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES.

8. Limitation Of Liability

EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER
BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED
UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY
OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PRODUCT. UNDER NO CIR­CUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST
DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTIN­GENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

9. Government Restricted Rights; International Use

9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for
computer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations
at FAR 52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013(c)(1)(ii), whichever is applicable.

9.2 If End User is using the Datalogic Product outside of the United States, End User must comply with the
applicable local laws of the country in which the Datalogic Product is used, with U.S. export control laws,

Software Product Policy

Quick Reference Guide v

and with the English language version of this Agreement. The provisions of the "United Nations Conven­tion on International Sale of Goods" shall not apply to this Agreement.

10. Termination

10.1Either party may terminate this Agreement or any license granted under this Agreement at any time upon
written notice if the other party breaches any provision of this Agreement.

10.2Upon termination of this Agreement, End User immediately shall cease using any nonembedded software
and shall return to Datalogic or destroy all non-embedded software covered by this Agreement, and shall
furnish Datalogic with a certificate of compliance with this provision signed by an officer or authorized
representative of End User. For embedded software, End User agrees to sign a waiver prepared by Data­logic concerning further use of the embedded Software. End User's resumed or continued use of the
embedded Software after termination shall constitute End User's agreement to be bound by the terms
and conditions of this Agreement for such use.

11. General Provisions

11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relat­ing to the licensing of the Software and supersedes all prior or contemporaneous agreements, written or
oral, between the parties concerning the licensing of the Software. This Agreement may not be changed,
amended, or modified except by written document signed by Datalogic.

11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be
effective when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of
Contract Administration, Datalogic ADC, Inc., 959 Terry Street, Eugene, OR 97402, or such other address as
may be specified by Datalogic in writing.

11.3 Waiver. A party's failure to enforce any of the terms and conditions of this Agreement shall not prevent
the party's later enforcement of such terms and conditions.

11.4 Governing Law; Venue: This Agreement and the rights of the parties hereunder shall be governed by and
construed in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing
conflicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane
counties shall have exclusive jurisdiction over all matters regarding this Agreement, except that Datalogic
shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state,
country, or territory in which End User resides, or in which any of End User's assets are located.

11.5 Attorneys' Fees. In the event an action is brought to enforce the terms and conditions of this Agreement,
the prevailing party shall be entitled to reasonable attorneys' fees, both at trial and on appeal.

- END -

Software Product Policy

Datalogic reserves the right to ship its products with the latest version of software/
firmware available. This provides our customers with the very latest in Datalogic soft­ware technology.

The only exception to this policy is when the buyer has a signed contract with Datalogic
that clearly defines the terms and conditions for making software/firmware changes in
products shipped to the buyer.

Customers Under Software Support

Customers that elect to subscribe to Datalogic Software Maintenance and Support
Agreement will receive 30 days advance notification of: (1) the release of a new software
version; and/or (2) discontinuation of any prior software version that will no longer be
supported. Datalogic will provide maintenance for a fee that will assist customers in
transitioning to the next software version. If a customer is currently using the software
version being discontinued, the customer may elect to transition to any one of the
newer versions, depending on the hardware in use.

To arrange for a Software Maintenance and Support Agreement please contact your
Datalogic sales person.

Software Product Policy

vi BC 9xx0 Cradle

NOTES

Quick Reference Guide 1

Using the BC9xx0 Base Station

The BC9xx0 base station, when paired with one or more PowerScan™ PM9500
readers, builds a Cordless Reading System for the collection, decoding and
transmission of bar code data. It can be connected to a Host PC via RS-232,
USB, or KBD Wedge, and is suited for single-cradle layouts.

The BC9x60 models also allow multi cradle layouts through an RS-485 Net­work. For this network connection refer to the Programming Reference
Guide.The BC91x0 models provide a spare battery charger slot. The BC9x80
models are provided with an Ethernet interface.

The label on the cradle contains LED indicators and a multi-function button.
When the button is pressed for less than 5 seconds, the cradle will transmit a
"broadcast" message." When the broadcast is sent, all properly configured
scanners (Radio RX Timeout set to keep the radio "awake") that are linked to
that base and within radio range coverage will emit a beep and blink within 5
seconds. This functionality is useful to:

• verify which scanners are linked to a certain base station

• detect a scanner forgotten somewhere

The LEDs signal the BC9xx0 status, as
shown.

LED STATUS

Aux Yellow On = BC9xx0 is powered through an external power supply.

Host Yellow On = BC9xx0 is powered by the Host.

Reader

Green On = the reader battery is completely charged.
Red On = the reader battery is charging.
Orange Blinking = reader battery fault - replace battery.
Red / Green Alternatively Blinking = charging error - see PRG.
Off = reader not in the cradle or not properly inserted.

Spare
(BC91x0 models only)

Green On = the spare battery is completely charged.
Orange Blinking = spare battery fault - replace spare battery.
Red/Green Alternatively Blinking = charging error - see PRG.
Off = no spare battery in the housing or battery not fully inserted.

Radio Yellow Blinking = radio activity.

Ethernet
(Ethernet models only)

Green Blinking = Ethernet activity.

Installation

2 BC 9xx0 Cradle

Installation

To set up your BC9xx0 cradle you must:

1. Physically install the cradle.

2. Make all system connections.

3. Configure the BC9xx0 cradle.

Mounting the BC9xx0 Cradle

The cradle package contains the following items:

The cradle can be either mounted on a flat surface for desktop usage or
affixed vertically to a wall.

Mounting Brackets

The cradle comes with two different mounting brackets. The appropriate
bracket is used depending on whether the cradle will be mounted on a hori­zontal or vertical surface. When shipped, the cradle has the Desktop Mount­ing Bracket installed. For vertical installation, the Wall Mounting Bracket
must be attached instead.

Figure 1. Mounting Brackets

• BC9xx0 Base Station (with Desktop
Mounting Bracket installed)

• 1 Metal Mounting plate

• BC9xx0 Quick Reference Guide
(this manual)

• 1 Wall Mounting Bracket

• 1 Ferrite Clamp (Ethernet models only)

Desktop Mounting Bracket

Wall Mounting Bracket

Ribs Bosses

(Horizontal ) (Vertical)

Tabs TabTab

Mounting the BC9xx0 Cradle

Quick Reference Guide 3

• Desktop mount bracket has ribs to keep the scanner in place when
the cradle is horizontal

• Wall mount bracket contains bosses to keep the scanner in place
when the cradle is vertical.

To change the Bracket:

1. Remove the screw holding the Bracket in place. Retain the screw for
re-use.

2. Carefully lift off the Bracket.

3. Install the other bracket by first slipping the end tab into place on
the base station, then easing the tabs (shown in Figure 1 on page 2)
into place on the sides.

4. Replace the screw to secure the Bracket to the Base Station.

Figure 2. Changing the Bracket

3

Mounting the BC9xx0 Cradle

4 BC 9xx0 Cradle

Permanent Mounting

For either desktop or wall mounting, the cradle can be fastened directly to a
flat surface using screws (not included).

Figure 3. Base Station Bottom

Mounting for Portable Use

If portability of the cradle is required, the metal plate must be used. There are
two ways this can be done: (1) by first mounting the metal plate on a flat sur­face so the cradle can be slid off and on, or (2) mounting the metal plate onto
the back of the base station and then screwing both to the desired surface.

Mounting the Metal Plate

1. Affix the metal plate onto the desired mounting surface using the
two center screw holes (see Figure 4 on page 5).

2. Remove the adhesive strips protecting the mounting tabs on the
cradle, shown in Figure 3.

3. Slide the tabs on the back of the cradle onto the metal plate as
shown in Figure 4.

4. After aligning the tabs, push up to lock into place.

When mounting on drywall, the base should be screwed to a wall
stud or supporting beam for additional support.

For additional security on wall mounting, it is strongly recom­mended that the cradle be secured into place using two auxiliary
screws through the mounting holes on the side.

Rubber Feet

Mounting HolesProtective adhesive strips

Rubber Feet

Mounting the BC9xx0 Cradle

Quick Reference Guide 5

Figure 4. Mounting Plate on Wall

Attaching the Metal Plate to Base

Alternatively, the mount can be attached first to the base, then both can be
mounted to a wall as described above.

Figure 5. Attaching Mounting Plate to Base

Base with Mount attached

System Connections

6 BC 9xx0 Cradle

System Connections

BC9x80 models - Ethernet Connection

The BC9x80 models contain an Ethernet connector and a power supply con­nector. A multi-interface connector is also available (intended for service pur-

poses only).

Ferrite Clamp Filter

CAUTION

Connections should always be made with power off!

CAUTION

Ensure the cable is plugged into the correct connector. Forcing
an Ethernet cable into the Multi-interface connector or forcing a
Multi-interface cable into the Ethernet connector could damage
the unit.

If a Ferrite Clamp filter is included in the package, mount it on
the Ethernet cable as shown, about 5 cm from the plug.

Ethernet Connector

Power Supply

Multi-Interface Connector

Cable and Ferrite Clamp

5cm

Ferrite Clamp

System Connections

Quick Reference Guide 7

Non-Ethernet Connection

The BC9xx0 cradle provides a multi-interface connector and a power supply
connector as shown:

Connecting and Disconnecting the Multi-Interface Cable

The BC9xx0 can be connected to a Host by means of a multi-interface cable,
which must be simply plugged into the Host connector, visible on the front
panel of the cradle.

To disconnect the cable, insert a paper clip or other similar object into the hole
corresponding to the Host connector on the body of the cradle. Push down on
the clip while unplugging the cable. Refer to the following figures:

RS-232

Power Supply

Multi-Interface Connector

Power

Interface Emulation
to Host

Connecting/Disconnecting the Cable

Configuration

8 BC 9xx0 Cradle

USB

WEDGE

Configuration

BC9x80 Ethernet Models

BC9x80 configuration can be performed using the Datalogic Aladdin software
configuration program or by reading configuration bar codes with the Power­Scan PM9500 reader.

Non-Ethernet Models

The BC9xx0 configuration can be performed in three ways: by using the Data­logic Aladdin

™

software configuration program, by sending configuration
strings from the Host PC via the RS-232 or USB-COM interface or by reading
configuration bar codes with the PowerScan

™

PM9500 reader.

Datalogic Aladdin™

Datalogic Aladdin™ (available for free download from the Datalogic website) is
a multi-platform utility program that provides a quick and user-friendly con­figuration method via the RS-232/USB-COM or Ethernet interface. It also
allows upgrading the software of the connected device (see the Datalogic
Aladdin

™

Help On-Line for more details).

Serial Configuration

By connecting the BC9xx0 to a PC through an RS-232 or USB-COM interface
cable it is possible to send configuration strings from the PC to BC9xx0.

Selecting the Interface Type

Quick Reference Guide 9

Configuration Bar Codes

Link the cradle and the reader using the procedures described in the Power­Scan

™

PM9500 Quick Reference. Once the pairing is complete, you can config-

ure the BC9xx0 cradle by reading the configuration bar codes in this manual.
To configure the BC9xx0 using the PowerScan

™

PM9500 reader (paired to the
cradle with the Bind command), follow the procedure according to the inter­face selected.

Selecting the Interface Type

Upon completing the physical connection between the reader and its host,
scan the appropriate bar code for your system’s correct interface type.

Configuring the Interface

Scan the programming bar code which selects the appropriate interface type
for the system the reader will be connected to.

Ethernet Interface (BC9x80 Models only)

Use the programming bar codes below to program the Ethernet interface, to
select between standard and Ethernet/IP and to choose between fixed IP
address and DHCP.

Unlike some other programming features and options, interface
selections require that you scan only one programming bar code
label. DO NOT scan an ENTER/EXIT bar code prior to scanning an
interface selection bar code.

Some interfaces require the scanner to start in the disabled state
when powered up. If additional scanner configuration is desired
while in this state, pull the trigger and hold for 5 seconds. The scan­ner will change to a state that allows programming with bar codes.

ETHERNET

Select Standard Ethernet

Select Ethernet/IP

Selecting the Interface Type

10 BC 9xx0 Cradle

Serial Interface

ETHERNET (continued)

Select Static IP Addressing

a

Select Dynamic IP Addressing

b

a. When Static IP Addressing is selected, 192.168.187.31 will be used as a

default; this can be changed using the Datalogic Aladdin configuration
program.

b. To use Dynamic IP Addressing , you must be sure that your network

system supports a DHCP server.

RS-232

RS-232 standard interface

Select RS232-STD

RS-232 Wincor-Nixdorf

Select RS232-WN

RS-232 for use with OPOS/UPOS/JavaPOS

Select RS-232 OPOS

Selecting the Interface Type

Quick Reference Guide 11

USB

USB COM to simulate RS-232 standard interface

USB-COM-STD

a

USB-OEM

(can be used for OPOS/UPOS/JavaPOS)

USB-OEM

USB Keyboard with standard key encoding

Select USB Keyboard

USB Keyboard with alternate key encoding

USB Alternate Keyboard

USB Keyboard for Apple computers

USB-KBD-APPLE

a. Download the correct USB COM driver from www.datalogic.com

Selecting the Interface Type

12 BC 9xx0 Cradle

Keyboard Interface

Use the programming bar codes to select options for USB Keyboard and
Wedge Interfaces.

KEYBOARD

AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/

Standard Key Encoding

Select KBD-AT

Keyboard Wedge for IBM AT PS2 with standard key encoding

but without external keyboard

Select KBD-AT-NK

AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95

w/Alternate Key

Select KBD-AT-ALT

Keyboard Wedge for IBM AT PS2 with alternate key encoding

but without external keyboard

Select KBD-AT-ALT-NK

PC/XT w/Standard Key Encoding

Select KBD-XT

Selecting the Interface Type

Quick Reference Guide 13

Scancode Tables

Reference the PowerScan™ 9500 PRG for information about control character
emulation which applies to keyboard interfaces.

KEYBOARD (continued)

Keyboard Wedge for IBM Terminal 3153

Select KBD-IBM-3153

Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make

only keyboard

Select KBD-IBM-M

Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make

break keyboard

Select KBD-IBM-MB

Keyboard Wedge for DIGITAL Terminals

VT2xx, VT3xx, VT4xx

Select KBD-DIG-VT

Selecting the Interface Type

14 BC 9xx0 Cradle

Country Mode

This feature specifies the country/language supported by the keyboard. Only
these interfaces support ALL Country Modes:

• USB Keyboard (without alternate key encoding)

• AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Std Key
Encoding

• Keyboard Wedge for IBM AT PS2 with standard key encoding but
without external keyboard

• AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 without Alter­nate Key

• Keyboard Wedge for IBM AT PS2 without alternate key encoding but
without external keyboard

All other interfaces support ONLY the following Country Modes: U.S., Belgium,
Britain, France, Germany, Italy, Spain, Sweden.

COUNTRY MODE

ENTER/EXIT PROGRAMMING MODE

Country Mode = U.S.

Country Mode = Belgium

Country Mode = Britain

*

Supports only the interfaces listed in the Country Mode feature description

Selecting the Interface Type

Quick Reference Guide 15

COUNTRY MODE (continued)

Country Mode = Croatia*

Country Mode = Czech Republic*

Country Mode = Denmark*

Country Mode = France

Country Mode = French Canadian

Country Mode = Germany

*

Supports only the interfaces listed in the Country Mode feature description

$CKBCO13(CR)

Selecting the Interface Type

16 BC 9xx0 Cradle

COUNTRY MODE (continued)

Country Mode = Hungary*

Country Mode = Italy

Country Mode = Japanese 106-key*

Country Mode = Lithuanian

Country Mode = Norway*

Country Mode = Poland*

Country Mode = Portugal*

*

Supports only the interfaces listed in the Country Mode feature description

$CKBCO14(CR)

Selecting the Interface Type

Quick Reference Guide 17

COUNTRY MODE (continued)

Country Mode = Romania*

Country Mode = Spain

Country Mode = Sweden

Country Mode = Slovakia*

Country Mode = Switzerland*

*

Supports only the interfaces listed in the Country Mode feature description

Selecting the Interface Type

18 BC 9xx0 Cradle

Caps Lock State

This option specifies the format in which the reader sends character data.
This applies to keyboard wedge interfaces. This does not apply when an alter­nate key encoding keyboard is selected.

CAPS LOCK STATE

ENTER/EXIT PROGRAMMING MODE

Caps Lock State = Caps Lock OFF

Caps Lock State = Caps Lock ON

Caps Lock State = AUTO Caps Lock Enable

Selecting the Interface Type

Quick Reference Guide 19

Numlock

This option specifies the setting of the Numbers Lock (Numlock) key while in
keyboard wedge interface. This only applies to alternate key encoding inter­faces. It does not apply to USB keyboard.

NUMLOCK

ENTER/EXIT PROGRAMMING MODE

Numlock = Numlock key unchanged

Numlock = Numlock key toggled

Selecting the Interface Type

20 BC 9xx0 Cradle

Resetting Standard Product Defaults

Reference the PRG for a listing of standard factory settings. If you aren’t sure
what programming options are in your reader, or you’ve changed some
options and want the factory settings restored, scan the

Standard Product

Default Settings

bar code below to copy the factory configuration for the cur-

rently active interface to the current configuration.

To change the defaults refer to the PowerScan

™

9500 PRG, or to the Datalogic

Aladdin

™

Configuration program, both downloadable from the Datalogic web-

site.

Compatibility with the PowerScan™ 8000 family

The BC9xx0 can be programmed to operate in a mode compatible with the
PowerScan 8000 family. For further details and for the relevant configuration
strings and labels, refer to the PRG.

Factory defaults are based on the interface type. Configure the
reader for the correct interface before scanning this label.

CAUTION

Scanning this bar code will RESET all settings for the PowerScan
PM9500. Any customized settings that may have been applied to
the reader will be lost.

Standard Product Default Settings

Technical Features

Quick Reference Guide 21

Technical Features

Electrical Features

Supply Voltage

External Power

Host Power

a

a. Host Power not supported on Ethernet Models

10 - 30 VDC
5 VDC ±10%

Power Consumption

External Power

Host Power

a

max. 10 W (charging)

b

max. 500 mA (charging)

b. Having a switching regulator inside, the BC9xx0 draws the same power, regardless of the supply volt-

age; i.e., as the input voltage increases the current drawn decreases

Indicators

Ext. Power/Data yellow LED

Host Power/Data yellow LED

Reader batt. state green/red LED

Spare batt. state green/red LED

Radio yellow LED

Ethernet green LED (Ethernet models only)

Time of Recharge

External Power

Host Power

a

max. 4 hours with 2150 mAh Li-Ion battery

max. 10 hours with 2150 mAh Li-Ion battery

Environmental Features

Working Temperature

Radio

Battery Charging

-20° to +50

°

C / -4 to +122 °F

0° to +40 °C / +32° to +104 °F

Storage Temperature -20° to +70

°

C / -4 to +158 °F

Humidity 90% non condensing

Protection Class IP40

Mechanical Features

Weight without metal plate about 390 g / 13.76 oz

Dimensions (without antenna) 235 x 108 x 80 mm

Regulatory

Electrical Safety

UL 60950, CSA C22.2 No.
60950, IEC 60950

EMI/RFI

433 MHz model

Europe - CE, Russia –
Gost; Australia – Ctick;
China – SRRC;
Singapore – IDA,
Anatel Brazil

910 MHz model

USA/Canada – FCC/IC;
Mexico – NOM + Cofetel

Technical Features

22 BC 9xx0 Cradle

Regulatory (continued)

Laser Class Safety

IEC Class 2
Radiation 1 mW Avg., Emitted wavelength 650 nm,
12ms pulse, Beam Divergence 8.4 deg x 8.1 deg
(“plus” pattern)

Complies with FDA performance standards for laser products except for deviations pursu­ant to Laser Notice No. 50, dated June 24, 2007.

Radio Features

Frequency working center

910MHz 433MHz

Programmable Speed

40 kb/s
100 kb/s
500 kb/s (default)

19.2 kb/s
100 kb/s
500 kb/s (default)

Typical Range (in open air) 100m

from 50m
(at 500 kb/s)
to 100m
(at 19.2kb/s)

Max number of devices per base
station

16

Regulatory Information

Quick Reference Guide 23

Regulatory Information

Compliance

This device must be opened by qualified personnel only.

Power Supply

This device is intended to be supplied by a UL Listed/CSA Certified Power Unit
marked "Class 2" or LPS power source rated 10-30 V DC, minimum 1 A, which
supplies power directly to the cradle.

Adaptador para Fuente de Poder Externa

FCC Compliance

Modifications or changes to this equipment without the expressed written
approval of Datalogic could void the authority to use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including
interference which may cause undesired operation.

Radio Compliance

Contact the competent authority responsible for the management of radio
frequency devices of your country to verify any possible restrictions or
licenses required.

Atencíon

Características de la fuente

de alimentación eléctrica.

Entrada:

100 - 240 Vca
min 0.35A 50-60 Hz

Salida:

+5VDC, máx2.5A
(-)Negativo al centro

Entrada:

100 - 240 Vca
min 0.6A 50-60 Hz

Salida:

+12VDC, máx1.5A
(-)Negativo al centro

Utilice en su red solo fuentes certificadas en Argentina.

El uso de fuentes de alimentación no compatibles puede resultar en riesgo de incendio o
de choque eléctrico para el usuario.



Regulatory Information

24 BC 9xx0 Cradle

China RoHS Statement

Powerscan

™

Base Station BC9180-XX China RoHS

㒊௳ྡ⛠

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

Chromium

(Cr(VI))

Polybrominated

biphenyls

(PBB)

Polybrominated

diphenyl ethers

(PBDE)

᭷ẘ᭷ᐖ≀峐ᡈඖ⣲

PART

摭

ợ

擱

භ௴撔

ከ㹜俼劗

ከ㹜Ḵ劗慂

Cable

⭥

㔶

X O O O O O

Printed Circuit Board Assy

⭥䐟ᶯ㓴

X O O O O O

Assembly, Module

ݹᆖ㓴Ԧ



X O O O O O

Power Supply

⭥Ⓚ

X O O O O O

O





௦⾲Ṉ䥵㒊௳ⓗᡤ᭷ᆒ峐㛸㕁󰵶㇨⏓䘬宍䥵㚱㭺㚱⭛䈑峐⛯ỶḶ󰵶⋶Ṣ㮹ℙ␴⚥ᾉ〗ṏ󰵣悐ᡤ栩ⶫⓗ

ࠓ䓝⫸ᾉ〗ṏ⑩󰵶㚱㭺㚱⭛䈑峐䘬旸慷天㯪˫(SJ/T 11363-2006) 奬⭂䘬旸慷ࠋ

X:௦⾲

Ṉ䥵㒊௳ᡤ⏝ⓗᆒ峐㛸㕁󰵶, ⮳ᑡ᭷୍䰣ᮦᩱ඼ᡤྵⓗ᭷ẘ᭷ᐖ≀峐檀Ḷ󰵶⋶Ṣ㮹ℙ␴⚥ᾉ〗ṏ󰵣悐ᡤ栩ⶫⓗ

ࠓ䓝⫸ᾉ〗ṏ⑩󰵶㚱㭺㚱⭛䈑峐䘬旸慷天㯪˫(SJ/T 11363-2006) 奬⭂䘬旸㔞

EFUP determined by “Look-up Method” (scanner).

ġġ䍗ᾅἧ䓐㛇旸⍾⅛Ḷ“㞍堐㱽”㸦㈓㍷Ẓ炸

Regulatory Information

Quick Reference Guide 25

WEEE Compliance

English

For information about the disposal of Waste Electrical and Electronic Equip­ment (WEEE), please refer to the website at www.datalogic.com.

Italian

Per informazioni sullo smaltimento delle apparecchiature elettriche ed elet­troniche consultare il sito Web www.datalogic.com.

French

Pour toute information relative à l’élimination des déchets électroniques
(WEEE), veuillez consulter le site Internet www.datalogic.com.

German

Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten
(WEEE) erhalten Sie auf der Webseite www.datalogic.com.

Spanish

Si desea información acerca de los procedimientos para el desecho de los
residuos del equipo eléctrico y electrónico (WEEE), visite la página Web

http://www.datalogic.com.

Portuguese

Para informações sobre a disposição de Sucatagem de Equipamentos Eléctri­cos e Eletrônicos (WEEE - Waste Electrical and Electronic Equipment), consul­tar o site web http://www.datalogic.com.

Chinese

有关处理废弃电气电子设备 (WEEE) 的信息， 请参考 Datalogic 公司的网
站：

http://www.datalogic.com/。

Japanese

廃電気電子機器 (ＷＥＥＥ) の処理についての関連事項は Datalogic の
サイト

http://www.datalogic.com/, をご参照下さい。

Waste Electrical and Electronic Equipment (WEEE) Statement

Datalogic ADC Limited Factory Warranty

26 BC 9xx0 Cradle

Datalogic ADC Limited Factory Warranty

Warranty Coverage

Datalogic warranties this product against defects in workmanship and materials, for a period
of 3 years from the date of shipment, provided that the product is operated under normal and
proper conditions. Datalogic (“Datalogic”) hardware products are warranted against defects
in material and workmanship under normal and proper use. The liability of Datalogic under
this warranty is limited to furnishing the labor and parts necessary to remedy any defect
covered by this warranty and restore the product to its normal operating condition. Repair or
replacement of product during the warranty does not extend the original warranty term.
Products are sold on the basis of specifications applicable at the time of manufacture and
Datalogic has no obligation to modify or update products once sold.

If Datalogic determines that a product has defects in material or workmanship, Datalogic
shall, at its sole option repair or replace the product without additional charge for parts and
labor, or credit or refund the defective products duly returned to Datalogic. To perform re­pairs, Datalogic may use new or reconditioned parts, components, subassemblies or prod­ucts that have been tested as meeting applicable specifications for equivalent new material
and products. Customer will allow Datalogic to scrap all parts removed from the repaired
product. The warranty period shall extend from the date of shipment from Datalogic for the
duration published by Datalogic for the product at the time of purchase (Warranty period).
Datalogic warrants repaired hardware devices against defects in workmanship and materi­als on the repaired assembly for a 90 day period starting from the date of shipment of the
repaired product from Datalogic or until the expiration of the original warranty period, which­ever is longer. Datalogic does not guarantee, and it is not responsible for, the maintenance
of, damage to, or loss of configurations, data, and applications on the repaired units and at
its sole discretion can return the units in the “factory default” configuration or with any soft­ware or firmware update available at the time of the repair (other than the firmware or soft­ware installed during the manufacture of the product). Customer accepts responsibility to
maintain a back up copy of its software and data.

Warranty Claims Process

In order to obtain service under the Factory Warranty, Customer must notify Datalogic of the
claimed defect before the expiration of the applicable Warranty period and obtain from Dat­alogic a return authorization number (RMA) for return of the product to a designated Data­logic service center. If Datalogic determines Customer’s claim is valid, Datalogic will repair or
replace product without additional charge for parts and labor. Customer shall be responsible
for packaging and shipping the product to the designated Datalogic service center, with ship­ping charges prepaid. Datalogic shall pay for the return of the product to Customer if the
shipment is to a location within the country in which the Datalogic service center is located.
Customer shall be responsible for paying all shipping charges, duties, taxes, and any other
charges for products returned to any other locations. Failure to follow the applicable RMA
policy, may result in a processing fee. Customer shall be responsible for return shipment ex­penses for products which Datalogic, at its sole discretion, determines are not defective or
eligible for warranty repair.

Warranty Exclusions

The Datalogic Factory Warranty shall not apply to:

(i) any product which has been damaged, modified, altered, repaired or upgraded by

other than Datalogic service personnel or its authorized representatives;

(ii) any claimed defect, failure or damage which Datalogic determines was caused by

faulty operations, improper use, abuse, misuse, wear and tear, negligence, improper
storage or use of parts or accessories not approved or supplied by Datalogic;

(iii) any claimed defect or damage caused by the use of product with any other instru-

ment, equipment or apparatus;

(iv) any claimed defect or damage caused by the failure to provide proper maintenance,

including but not limited to cleaning the upper window in accordance with product
manual;

(v) any defect or damage caused by natural or man-made disaster such as but not lim-

ited to fire, water damage, floods, other natural disasters, vandalism or abusive
events that would cause internal and external component damage or destruction of
the whole unit, consumable items;

Ergonomic Recommendations

Quick Reference Guide 27

(vi) any damage or malfunctioning caused by non-restoring action as for example firm-

ware or software upgrades, software or hardware reconfigurations etc.;

(vii) the replacement of upper window/cartridge due to scratching, stains or other deg-

radation and/or

(viii) any consumable or equivalent (e.g., cables, power supply, batteries, keypads, touch

screen, triggers etc.).

No Assignment

Customer may not assign or otherwise transfer its rights or obligations under this warranty
except to a purchaser or transferee of product. No attempted assignment or transfer in vio­lation of this provision shall be valid or binding upon Datalogic.

DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IM­PLIED, ORAL OR WRITTEN, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION,
ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE FOR ANY DAMAGES SUSTAINED
BY CUSTOMER ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UN­DER THE ABOVE. THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT IS THE CUSTOM­ER’S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY CLAIMS. UNDER NO CIRCUMSTANCES
WILL DATALOGIC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS,
OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT DAMAGES RE­GARDLESS OF WHETHER DATALOGIC HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGES.

Risk of Loss

Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall
assume risk of loss or damage for product in Datalogic’s possession. In the absence of spe­cific written instructions for the return of product to Customer, Datalogic will select the car­rier, but Datalogic shall not thereby assume any liability in connection with the return
shipment.

Ergonomic Recommendations

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

•Provide a suitable working environment

• Improve work procedures

CAUTION

In order to avoid or minimize the potential risk of ergonomic injury
follow the recommendations below. Consult with your local Health &
Safety Manager to ensure that you are adhering to your company’s
safety programs to prevent employee injury.

Services and Support

28 BC 9xx0 Cradle

Services and Support

Datalogic provides several services as well as technical support through its
website. Log on to www.datalogic.com and click on the links indicated for fur-
ther information.

Products

Search through the links to arrive at your product page where you can down­load specific Manuals and Software & Utilities, including:

• Datalogic Aladdin™, a multi-platform utility program that allows
device configuration using a PC. It provides RS-232/USB-COM or
Ethernet interface configuration, printing of configuration bar
codes, and firmware upgrades.

Service & Support

• Technical Support - Product documentation and programming
guides and Technical Support Department in the world

• Service Programs - Warranty Extensions and Maintenance Agree­ments

• Repair Services - Flat Rate Repairs and Return Material Authoriza­tion (RMA) Repairs

• Downloads – Manuals & Documentation, Data Sheets, Product Cat­alogues, etc.

Contact Us

• Information Request Form and Sales & Service Network

Services and Support

Quick Reference Guide 29

NOTES

Services and Support

30 BC 9xx0 Cradle

NOTES

DECLARATION OF CONFORMITY

La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva di Datalogic ADC Srl
per:
This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC Srl for:
Cette déclaration de conformité est établie sous la seule responsabilité de Datalogic Srl pour:
Diese Konformitätserklärung wird unter der alleinigen Verantwortung des Datalogic ADC Srl erteilt für:
Esta declaración de conformidad se expide bajo la exclusiva responsabilidad de Datalogic ADC Srl para:

PowerScan PM9500 ; Cordless Barcode Reader
BC9XY0-433 ; Cordless Base Station/Charger

sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:

1999/5/EC - R&TTE Directive

2011/65/EU - RoHS Directive

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:

Datalogic ADC Srl, Via S. Vitalino, 13
Lippo di Calderara di Reno (BO) 40012 Italy

EC-101
Rev.: 1
Pag.: 1 di 1

e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos

ETSI EN 301 489-3 V1.4.1, A

UGUST

2002 :

E

LECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MAT

-

TERS

(ERM); E

LECTROMAGNETIC COMPATIBILITY

(EMC)

STANDARD

FOR RADIO EQUIPMENT AND SERVICES

; P

ART

3: S

PECIFIC CONDI

-

TIONS FOR SHORT-RANGE DEVICES

(SRD) O

PERATING ON FRE

-

QUENCIES BETWEEN 9KHZ AND

40

GHZ

EN 301 489-1 V1.8.1, A

PRIL

2008 :

EL

ECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MAT

-

TERS

(ERM); E

LECTROMAGNETIC COMPATIBILITY

(EMC) S

TAN

-

DARD FOR RADIO EQUIPMENT AND SERVICES

; P

ART

1: C

OMMON

T

ECHNICAL REQUIREMENTS

ETSI EN 300 220-2 V2.1.2, J

UNE

2007 :

E

LECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MAT

-

TERS

(ERM); S

HORT RANGE DEVICES

(SRD); R

ADIO EQUIPMENT

TO BE USED IN THE

25

MHZ TO

1000

MHZ FREQUENCY RANGE

WITH POWER LEVELS RANGING UP TO

500MW; P

ART

2: H

ARMO

-

NIZED

EN C

OVERING ESSENTIAL REQUIREMENTS UNDER ARTICLE

3.2 OF

THE

R&TTE D

IRECTIVE

EN 60950-1, D

ECEMBER

2006 + A

MEND

-

MENT

A11:2009 + A

MENDMENT

A1:2010 +

A

MENDMENT

A12:2011

I

NFORMATION TECHNOLOGY EQUIPMENT

- S

AFETY

-

P

ART

1 : G

ENERAL REQUIREMENTS

EN 50581, S

EPTEMBER

2012 :

T

ECHNICAL DOCUMENTATION FOR THE ASSESSMENT OF ELECTRI

-

CAL AND ELECTRONIC PRODUCTS WITH RESPECT TO THE RESTRIC

-

TION OF HAZARDOUS SUBSTANCES

Lippo di Calderara, August 29th , 2013

R

UGGERO CACIOPPO

Q

UALITY

& R

ELIABILITY MANAGER

- E

UROPE

14

©2013-2014 Datalogic, Inc. • All rights reserved.
Datalogic and the Datalogic logo are registered
trademarks of Datalogic S.p.A. in many countries,
including the U.S.A. and the E.U.

Datalogic ADC, Inc.

959 Terry Street | Eugene |OR 97402 | USA
Telephone: [phone]

|

Fax: [phone]

www.datalogic.com

820064514 (Rev A) July 2014