Datalogic BC-80X0 Cradle Quick Reference Manual

BC-80X0 Cradle
Quick Reference Guide
Datalogic Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
USA
Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the
procedures described therein may be reproduced or transmitted in any form or by any means with-
out prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic"
or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, revo-
cable license to reproduce and transmit this documentation for the purchaser's own internal busi-
ness purposes. Purchaser shall not remove or alter any proprietary notices, including copyright
notices, contained in this documentation and shall ensure that all notices appear on any reproduc-
tions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contact-
ing your Datalogic representative. Electronic versions may either be downloadable from the Data-
logic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our
website and would like to make comments or suggestions about this or other Datalogic publica-
tions, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete
and accurate, however, Datalogic reserves the right to change any specification at any time with-
out prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries,
including the U.S.A and the E.U. All other brand and product names referred to herein may be
trademarks of their respective owners.
Patents
This product is covered by US Pat. 7,948,214 B2. Additional patents pending.
BC-80X0
1
LED
STATUS
Aux
Yellow On = BC-80X0 is powered through an external power supply. Yellow Blinking = BC-80X0 transmission occurs over the Host port.
Host
Yellow On = BC-80X0 is powered by the Host. Yellow Blinking = BC-80X0 transmission occurs over the Host port.
Reader
Green On = the reader battery is completely charged. Red On = the reader battery is charging. Orange Blinking = reader battery fault – replace battery. Red / Green Alternatively Blinking = charging error - see Ref. Manual
Spare*
Green On = the spare battery is completely charged. Red On = the spare battery is charging. Orange Blinking = spare battery fault – replace battery.
Red / Green Alternatively Blinking = charging error - see Ref. Manual
Figure 1 – Cradle Overview
Figure 2 – LEDs
USING THE BC-80X0 RADIO CRADLE
The BC-80X0 cradle, paired with one or more Powerscan™ M8300 readers, builds a Cordless Reading System for the collection, decoding and transmission of barcoded data.
It can be connected to a Host PC through an RS-232, USB, Wedge or Pen cable and is suited for single-cradle point-to-point layouts. It can also be connected to a C-BOX and therefore integrated into a fixed scanner application.
The BC-8060 models also allow multi-cradle layouts through an RS-485 Network. For this network connection refer to the Powerscan™ D8330/M8300 Reference Manual.
The label on the cradle contains LED indicators and a scan finder button. When the button is pressed, the cradle transmits a “broadcast” message. All properly configured scanners (Radio RX Timeout set to keep the radio “awake”) that are linked to that base (through a bind or a join sequence) and within radio range coverage will emit a beep sequence once every 2 seconds for 30 seconds. This functionality is useful to:
- verify which scanners are linked to a certain base station
- detect a scanner forgotten somewhere
The LEDs signal the BC-80X0 status, as described in the following table:
* This LED refers to the accessory SBS-8000 Spare Battery Slot when mounted to the BC-8060. Not
available for BC-8010 models.
DATALOGIC
2
BC-80X0
1 horizontal base
BC-80X0 Quick Reference Guide
2 wall-mounting lock hinges
BC-8000 Antenna
4 rubber feet
2 adhesive strips
1 inclined base
BC-80X0 Cradle mounted on the Inclined Base
To set up your BC-80X0 cradle you must:
1. Physically install the cradle.
2. Make all system connections.
3. Configure the BC-80X0 cradle.
INSTALLATION
MOUNTING THE BC-80X0 CRADLE
The cradle package contains the following items:
The cradle can be mounted for portable or fixed desktop usage, or it can be fixed to a wall. The horizontal base allows portable and fixed desktop usage, while the inclined base provides desktop and wall mounting guaranteeing a comfortable handling of the Powerscan™ M8300 reader.
BC-80X0 Cradle mounted on the Horizontal Base
BC-80X0
3
Mounting Tabs (4)
Mounting Holes (2)
Rubber Foot Seat (4)
Adhesive Strip Seat (2)
Cable Channels
Mounting
Tabs (4)
Mounting Holes (4)
Cable Channels
Adhesive Strip Seat (2)
Rubber Foot Seat (4)
Desktop mounting
For desktop usage, you can mount the cradle either on the horizontal base, for reduced overall dimensions, or on the inclined base for a more ergonomic taking out and insertion of the reader onto the cradle.
Horizontal base
Top View Bottom View
Inclined base
Top View Bottom View
DATALOGIC
4
1
2
1
2
Horizontal Base
Inclined Base
PORTABLE DESKTOP USE
1. Correctly position the BC-80X0 onto the base by sliding it along the mounting tabs until aligned.
2. Carefully clean the rubber foot seats of the base to remove any impurities that could reduce adhesion.
3. Remove the protective plastic from the rubber feet and stick them onto the bottom surface of the base.
4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.
FIXED DESKTOP USE
For fixed desktop installation, use the adhesive strips or fixing screws (not provided) according to your needs.
For mounting with adhesive strips:
1. Position the cradle onto the base by sliding it along the mounting tabs until aligned.
2. Carefully clean the adhesive strip seats of the base to remove any impurities that could reduce adhesion.
3. Remove the protective plastic from one side of the adhesive strips and stick them onto the base surface.
4. Position the cables to be connected to the BC-80X0 cradle along the dedicated channels, as shown in the figures below:
BC-80X0
5
5. Remove the plastic from the other side of the strips and affix the base to the table.
6. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.
For mounting with screws:
1. Position the cables to be connected to the BC-80X0 cradle along the dedicated channels, as shown in the figures below:
2. Position the base on the table and affix it by means of the screws (not provided).
3. Position the cradle on the base by sliding it along the mounting tabs until aligned.
4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.
Wall Mounting
1. Remove the yellow caps and insert the two wall mounting lock hinges provided with your cradle.
DATALOGIC
6
If using the adhesive strips:
3. Carefully clean the adhesive strip seats of the base to remove any impurities that could reduce adhesion.
4. Remove the protective plastic from one side of the adhesive strips and stick them onto the base surface.
5. Remove the plastic from the other side of the strips and affix the base to the wall as indicated in the figure below.
If using the mounting screws:
3. Using the mounting holes on the base as a pattern, mark the wall where you desire to mount the BC-80X0.
4. Drill the appropriate size holes and insert the threaded dowels (not provided) into the holes.
5. Position the base on the wall as indicated in the figure below and affix it by means of the screws (not provided).
2. Position the cables to be connected to the BC-80X0 cradle along the dedicated channels (see figures at page 4).
6. Attach the cradle on the base by sliding it along the mounting tabs until aligned.
7. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.
Inclined Base Wall-mounting
BC-80X0
7
A pre-printed barcode label is included in the package for rapid configuration of point-to­point applications. If you wish to use this method, apply this label to the seat provided on the BC-80X0 cradle as shown in the figure. See the Powerscan™ M8300 Quick Reference Manual for the configuration procedure.
Connections should always be made with power off!
CAUTION
Power Supply
RS-485
(BC-8060 only)
MULTI-INTERFACE
RS-232, USB, Wedge,
PEN Emulation
APPLYING RAPID POINT-TO-POINT CONFIGURATION LABEL (OPTIONAL)
SYSTEM CONNECTIONS
The BC-80X0 cradle provides two interface connectors and a power supply connector as shown in the figure on the next page:
The RS-485 Network connection is available only on BC-8060 models. For details about this type of connection, refer to the Powerscan™ D8330/M8300 Reference Manual.
To connect the BC-80X0 cradle to the Host through the multi-interface
connector, use the cable corresponding to the desired interface type.
DATALOGIC
8
Connecting/Disconnecting the Cable
Power
Multi-standard interface RS-232, USB, WEDGE, or PEN Emulation to Host
CONNECTING AND DISCONNECTING THE BC-80X0 INTERFACE CABLE
The BC-80X0 can be connected to a Host by means of an RS-232, USB, Wedge or Pen cable, which must be simply plugged into the Host connector, visible on the front panel of the cradle.
To disconnect the cable, insert a paper clip or other similar object into the hole corresponding to the Host connector on the body of the cradle. Push down on the clip while unplugging the cable. Refer to the following figure:
RS-232
USB
BC-80X0
9
Powerscan™ M
BC-80X0
BIND
JOIN
C-BOX
Scanner
System cables to Host
WEDGE
PEN
C-BOX
DATALOGIC
10
BC-80X0 CONFIGURATION
The BC-80X0 configuration can be performed in three ways: by using the Datalogic Aladdin™ software configuration program, by sending configuration strings from the Host PC via the RS-232 or USB-COM interface or by reading configuration barcodes with the Powerscan™ M reader.
DATALOGIC ALADDIN™
Datalogic Aladdin™ is a multi-platform utility program providing a quick and user-friendly configuration method via the RS-232/USB-COM interface. It also allows upgrading the software of the connected device (see the Datalogic Aladdin™ Help On-Line for more details).
SERIAL CONFIGURATION
By connecting the BC-80X0 to a PC through an RS-232 or USB-COM interface cable it is possible to send configuration strings from the PC to BC-80X0.
CONFIGURATION BARCODES
Once you have performed system connection and Powerscan™ M reader configuration, you can configure the BC-80X0 cradle by reading configuration barcodes. Apply power to the BC-80X0.
For Powerscan™ M configuration, refer to the “Powerscan™ M8300 Quick Reference”.
To configure the BC-80X0 using the Powerscan™ M reader (the one paired to the cradle with the Bind command), follow the procedure according to the interface selected.
RESTORE DEFAULT
RESTORE BC-80X0 DEFAULT
Ì$+RX0$-qÎ
To change the defaults refer to the "Powerscan™ D8330/M8300 Reference Manual", or to the Datalogic Aladdin™ Configuration program, both downloadable from the website.
11
USB INTERFACE SELECTION
USB-KBD
Ì$+UA03$-:Î
USB-KBD – ALT-mode
Ì$+UA04$-@Î
USB-COM*
Ì$+UA02$-4Î
USB-IBM-Hand Held
Ì$+UA01$-.Î
USB-IBM Table top
Ì$+UA00$-(Î
USB KBD-APPLE
PEN EMULATION INTERFACE SELECTION
PEN
Ì$+CP6$-BÎ
INTERFACE SELECTION
Select one of the interface codes according to your application.
BC-80X0
* When configuring USB-COM, the relevant files and drivers must be installed
from the USB Device Installation Software, which can be downloaded from the web site http://www.scanning.datalogic.com.
DATALOGIC
12
RS-232 INTERFACE SELECTION
RS-232 Standard
Ì$+CP0$-$Î
Nixdorf Mode A
Ì$+CM2EC0$->Î
Fujitsu
Ì$+CM1$-ÈÎ
ICL Mode
Ì$+CM0$-ÃÎ
WEDGE INTERFACE SELECTION
Wedge IBM AT or PS/2 PCs
Ì$+CP500$-aÎ
PC Notebook
Ì$+CP505$-ÈÎ
PC Notebook - ALT mode
Ì$+CP508$-2Î
IBM AT - ALT mode
Ì$+CP507$-+Î
INTERFACE SELECTION
Select one of the interface codes according to your application.
Interfaces for IBM XT and IBM Terminals 3151, 347X and 348X can be selected from the PowerScan D8330/M8300 Reference Manual available online at
http://www.scanning.datalogic.com.
13
USB-KBD and Wedge users should select one of the following wedge keyboard nationality codes according to your keyboard.
Belge
Ì$+FJ7$-8Î
Deutsch
Ì$+FJ3$-$Î
English
Ì$+FJ4$-)Î
Español
Ì$+FJ6$-3Î
Français
Ì$+FJ2$-ÊÎ
Italiano
Ì$+FJ1$-ÅÎ
Svenskt
Ì$+FJ5$-.Î
USA (Default)
Ì$+FJ0$-|Î
KEYBOARD NATIONALITY
BC-80X0
DATALOGIC
14
Japanese
Ì$+FJ8$-=Î
Russian (Latin)
Ì$+FJ9$-BÎ
Russian (Cyrillic)
Ì$+FJA$-jÎ
Hungarian
Ì$+FJB$-oÎ
Slovenian, Croatian, Serbian (Latin)
Ì$+FJC$-tÎ
Romanian
Ì$+FJD$-yÎ
Czech Republic
Ì$+FJE$-~Î
The following Keyboard Nationality selections are only valid for IBM AT compatible PCs:
BC-80X0
15
CR-LF
Ì$+EA120D0A$-ÃÎ
Enter
Ì$+EA1183$-0Î
Tab
Ì$+EA1184$-8Î
None
Ì$+EA10$-dÎ
DATA FORMAT TERMINATORS
For your convenience, some common Terminators are given below. For other Header/Terminators selections, Data Format and Advanced Data Format parameters see the Powerscan™ D8330/M8300 Reference Manual.
DATALOGIC
16
BC-80X0 DEFAULT CONFIGURATION
USB-KBD DEFAULT SETTINGS
USA keyboard, FIFO enabled, inter-character and inter-code delays disabled, USB keyboard speed normal.
DATA FORMAT: code identifier disabled, code length not transmitted, character
replacement disabled, reader and cradle address stamping disabled, reader and cradle address delimiter disabled, time stamping disabled, time stamping delimiter disabled, no header, terminator = ENTER.
RS-232 DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, ack/nack protocol disabled, FIFO enabled, delay disabled, 5 sec. rx timeout
DATA FORMAT: code identifier disabled, code length not transmitted, character
replacement disabled, reader and cradle address stamping disabled, reader and cradle address delimiter disabled, time stamping disabled, time stamping delimiter disabled, no header, terminator = CR-LF.
WEDGE DEFAULT SETTINGS
USA keyboard, Caps Lock off, Caps Lock Auto-Recognition enabled, num lock unchanged, inter-character and intercode delay disabled, control character emulation = ctrl+shift+key.
DATA FORMAT: code identifier disabled, code length not transmitted, character
replacement disabled, reader and cradle address stamping disabled, reader and cradle address delimiter disabled, time stamping disabled, time stamping delimiter disabled, no header, terminator = ENTER.
PEN DEFAULT SETTINGS
Interpret operating mode, conversion to code 39, output level normal, idle level normal, minimum output pulse 600 s, overflow medium, inter-block delay disabled.
NETWORK PARAMETERS
RS-485 network disabled (for BC-8000 only).
17
1 2 3 4 5 6 7 0
1 2 3 4 5 6 7 0 0 0 9 9 2
1 7 1 6 2
Code 39 (Normal)
t e s t
0 1 2 3 4 5 6 7 8 4
OPERATING TEST
Read the TEST codes below.
BC-80X0
EAN-8
EAN-13
Code 39 (Normal)
Code 128
YOUR SYSTEM IS NOW READY TO READ CODES AND TO SEND THE DATA TO THE HOST.
Interleaved 2 of 5
DATALOGIC
18
BC-80X0
Electrical Features
Supply Voltage
External Power
10..30 VDC
Host Power
5 VDC ±10%
Power Consumption
External Power
max. 10 W (charging) *
Host Power
max. 500 mA (charging)
Indicators
Ext. Power/Data yellow LED
Host Power/Data yellow LED
Reader batt. state green/red LED
Spare batt. state green/red LED (BC-8060 only)
beeper
Time of Recharge
External Power
max. 4 hours with 2150 mAh Li-Ion battery
Host Power
max. 10 hours with 2150 mAh Li-Ion battery
Radio Features
European Models
USA Models
Radio frequency
433.92 MHz
910 MHz
Bit Rate
19200 baud
36800 baud
Range (in open air)
50 m
30 m
Environmental Features
Working Temperature
Radio
-20° to +50 °C / -4° to +122 °F
Battery Charging
0° to +40 °C / +32° to +104 °F
Storage Temperature
-20° to +70 °C / -4° to +158 °F
Humidity
90 % non condensing
Protection Class
IP40
Mechanical Features
Weight without mounting base
about 380 g / 13.4 oz
Dimensions (without antenna)
240 x 108 x 95 mm / 9.44 x 4.25 x 3.74 in
Material
ABS
System Configuration
BC-80X0
STARGATE™
Max number of devices per base station
32
255
Max number of devices in the same reading area
2000
BC-8060
STARGATE™
Max number of base stations in network
16 (including cradle Master)
TECHNICAL FEATURES
* Having a switching regulator inside, the BC-80X0 draws the same power, regardless of
the supply voltage. i.e. as the input voltage increases the current drawn decreases.
BC-80X0
19
WARRANTY
DATALOGIC SCANNING LIMITED FACTORY WARRANTY
Warranty Coverage
Datalogic warranties this product against defects in workmanship and materials, for a period of 3 years from the date of shipment, provided that the product is operated under normal and proper conditions.
Datalogic Scanning (“Datalogic”) hardware products are warranted against defects in material and workmanship under normal and proper use. The liability of Datalogic under this warranty is limited to furnishing the labor and parts necessary to remedy any defect covered by this warranty and restore the product to its normal operating condition. Repair or replacement of product during the warranty does not extend the original warranty term. Products are sold on the basis of specifications applicable at the time of manufacture and Datalogic has no obligation to modify or update products once sold.
If Datalogic determines that a product has defects in material or workmanship, Datalogic shall, at its sole option repair or replace the product without additional charge for parts and labor, or credit or refund the defective products duly returned to Datalogic. To perform repairs, Datalogic may use new or reconditioned parts, components, subassemblies or products that have been tested as meeting applicable specifications for equivalent new material and products. Customer will allow Datalogic to scrap all parts removed from the repaired product. The warranty period shall extend from the date of shipment from Datalogic for the duration published by Datalogic for the product at the time of purchase (Warranty period). Datalogic warrants repaired hardware devices against defects in workmanship and materials on the repaired assembly for a 90 day period starting from the date of shipment of the repaired product from Datalogic or until the expiration of the original warranty period, whichever is longer. Datalogic does not guarantee, and it is not responsible for, the maintenance of, damage to, or loss of configurations, data, and applications on the repaired units and at its sole discretion can return the units in the “factory default” configuration or with any software or firmware update available at the time of the repair (other than the firmware or software installed during the manufacture of the product). Customer accepts responsibility to maintain a back up copy of its software and data.
Warranty Claims Process
In order to obtain service under the Factory Warranty, Customer must notify Datalogic of the claimed defect before the expiration of the applicable Warranty period and obtain from Datalogic a return authorization number (RMA) for return of the product to a designated Datalogic service center. If Datalogic determines Customer’s claim is valid, Datalogic will repair or replace product without additional charge for parts and labor. Customer shall be responsible for packaging and shipping the product to the designated Datalogic service center, with shipping charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Datalogic service center is located. Customer shall be responsible for paying all
DATALOGIC
20
shipping charges, duties, taxes, and any other charges for products returned to any other locations. Failure to follow the applicable RMA policy, may result in a processing fee. Customer shall be responsible for return shipment expenses for products which Datalogic, at its sole discretion, determines are not defective or eligible for warranty repair.
Warranty Exclusions
The Datalogic Factory Warranty shall not apply to:
(i) any product which has been damaged, modified, altered, repaired or
upgraded by other than Datalogic service personnel or its authorized representatives;
(ii) any claimed defect, failure or damage which Datalogic determines
was caused by faulty operations, improper use, abuse, misuse, wear and tear, negligence, improper storage or use of parts or accessories not approved or supplied by Datalogic;
(iii) any claimed defect or damage caused by the use of product with any
other instrument, equipment or apparatus;
(iv) any claimed defect or damage caused by the failure to provide proper
maintenance, including but not limited to cleaning the upper window in accordance with product manual;
(v) any defect or damage caused by natural or man-made disaster such
as but not limited to fire, water damage, floods, other natural disasters, vandalism or abusive events that would cause internal and external component damage or destruction of the whole unit, consumable items;
(vi) any damage or malfunctioning caused by non-restoring action as for
example firmware or software upgrades, software or hardware reconfigurations etc.;
(vii) the replacement of upper window/cartridge due to scratching, stains
or other degradation and/or
(viii) any consumable or equivalent (e.g., cables, power supply,
batteries, keypads, touch screen, triggers etc.).
No Assignment
Customer may not assign or otherwise transfer its rights or obligations under this warranty except to a purchaser or transferee of product. No attempted assignment or transfer in violation of this provision shall be valid or binding upon Datalogic.
DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, ORAL OR WRITTEN, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE FOR ANY DAMAGES SUSTAINED BY CUSTOMER ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UNDER THE ABOVE. THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY CLAIMS. UNDER NO CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO
BC-80X0
21
CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss or damage for product in Datalogic’s possession. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment.
SERVICE AND SUPPORT
Datalogic provides several services as well as technical support through its website. Log on to www.scanning.datalogic.com and click on the links indicated for further information including:
PRODUCTS
Search through the links to arrive at your product page where you can download specific Manuals and Software & Utilities including:
- Datalogic Aladdin™, a multi-platform utility program that allows device configuration using a PC. It provides RS-232 interface configuration as well as configuration barcode printing.
SERVICE & SUPPORT
- Technical Support - Product documentation and programming guides and Technical Support Department in the world
- Service Programs - Warranty Extensions and Maintenance Agreements
- Repair Services - Flat Rate Repairs and Return Material Authorization (RMA) Repairs.
- Downloads – Manuals & Documentation, Data Sheets, Product Catalogues, etc.
CONTACT US
Information Request Form and Sales & Service Network
DATALOGIC
22
COMPLIANCE
This device must be opened by qualified personnel only.
POWER SUPPLY
This device is intended to be supplied by a UL Listed/CSA Certified Power Unit marked "Class 2" or LPS power source rated 10-30 V DC, minimum 1 A, which supplies power directly to the cradle.
FCC COMPLIANCE
Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.
This device contains FCC ID U4F0015.
RADIO COMPLIANCE
Contact the competent authority responsible for the management of radio frequency devices of your country to verify any possible restrictions or licenses required. Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm for further information.
BC-80X0
23
Waste Electrical and Electronic Equipment (WEEE) Statement
WEEE COMPLIANCE
English
For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.scanning.datalogic.com.
Italian
Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.scanning.datalogic.com.
French
Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site internet www.scanning.datalogic.com.
German
Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE) erhalten Sie auf der Webseite www.scanning.datalogic.com.
Spanish
Si desea información acerca de los procedimientos para el desecho de los residuos del equipo eléctrico y electrónico (WEEE), visite la página Web
www.scanning.datalogic.com.
Portuguese
Para informações sobre a disposição de Sucatagem de Equipamentos Elétricos e Eletrônicos (WEEE -Waste Electrical and Electronic Equipment), consultar o site web www.scanning.datalogic.com.
Chinese
有关处理废弃电气电子设备 (WEEE)的信息, 请参考Datalogic公司的网站: http://www.scanning.datalogic.com。
Japanese
廃電気電子機器(WEEE)の処理についての関連事項はDatalogicのサイト
www.scanning.datalogic.com, をご参照下さい。
DATALOGIC
24
NOTES
Datalogic Scanning, Inc.
07
959 Terry Street
Eugene, OR 97402
USA
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
1999/5/EEC R&TTE
ETSI EN 301 489-3 v1.4.1, August 2002:
ELECTROMAGNETIC COMPATIBILITY AND RADIO
SPECTRUM MATTERS (ERM); ELECTROMAGNETIC
COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT
AND SERVICES; PART 3: SPECIFIC CONDITIONS FOR
SHORT-RANGE DEVICES (SRD) OPERATING ON
FREQUENCIES BETWEEN 9 KHZ AND 40 GHZ
ETSI EN 300 220-3 v1.1.1, September 2000:
ELECTROMAGNETIC COMPATIBILITY AND RADIO
SPECTRUM MATTERS (ERM); SHORT RANGE DEVICES
(SRD); RADIO EQUIPMENT TO BE USED IN THE 25 MHZ TO 1000 MHZ FREQUENCY RANGE W ITH POWER LEVELS
RANGING UP TO 500 MW; PART 3: HARMONIZED EN COVERING ESSENTIAL REQUIREMENTS UNDER ARTICLE 3.2 OF THE R&TTE DIRECTIVE
EN 60950-1, December 2001:
INFORMATION TECHNOLOGY EQUIPMENT SAFETY PART 1: GENERAL REQUIREMENTS
December 20, 2007
dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el
BC-80X0, RF Base Charger
sono conformi alla Direttiva del Consiglio Europeo sottoelencata: are in conformity with the requirements of the European Council Directive listed below: sont conformes aux spécifications de la Directive de l'Union Européenne ci-dessous: der nachstehenden angeführten Direktive des Europäischen Rats entsprechen: cumple con los requisitos de la Directiva del Consejo Europeo, según la lista siguiente:
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti: This declaration is based upon compliance of the products to the following standards: Cette déclaration repose sur la conformité des produits aux normes suivantes: Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht: Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
©2007-2011 Datalogic Scanning, Inc. 820042814 (Rev. C) July-2011
Australia
Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com
France and Benelux
Datalogic Scanning SAS Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com
Germany
Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.com
India
Datalogic Scanning India Telephone: 91- 22 - 64504739 india.scanning@datalogic.com
Italy
Datalogic Scanning SpA Telephone: [39] (0) 39/62903.1 italy.scanning@datalogic.com
Japan
Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com
Latin America
Datalogic Scanning, Inc Telephone: (305) 742-2206 latinamerica.scanning@datalogic.com
Singapore
Datalogic Scanning Singapore PTE LTD Telephone: (65) 6435-1311 singapore.scanning@datalogic.com
Iberia
Datalogic Scanning SAS Sucursal en España Telephone: 34 91 746 28 60 spain.scanning@datalogic.com
United Kingdom
Datalogic Scanning LTD Telephone: 44 (0) 1582 464900 uk.scanning@datalogic.com
Datalogic Scanning, Inc.
959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140
www.scanning.datalogic.com
Loading...