Dart Controls 530 Series Catalog Page
530 Series
The 530 Series is Dart’s top of the line, feature packed
drive. Rated up to 3HP, this drive offers all the features
typically needed in an SCR drive application. The 530
Series control combines advanced engineering design,
premium component selection and rigorous quality
control to deliver an excellent off-the-shelf SCR drive.
Dependable, time-proven circuitry offers performance
characteristics previously available only in more costly
drives.
While providing a wide range of standard features,
many options quickly and easily extend the 530 Series’
capabilities to meet specic application requirements.
An integral part of a distinguished line of quality
products, the 530 Series is representative of Dart’s
continuing effort to provide reliable, versatile drives to
the OEM, distributor, and industrial markets.
530BRC
10
530BRE
530 SERIES FEATURES + SPECIFICATIONS
• Dual Voltage 120/240 VAC, 50/60Hz
• Full HP rated - no auxiliary heat sink required
• ± 10% rated line voltage
• Adjustable horsepower settings
• Barrier terminal strip
• Full wave bridge supply; 1% speed regulation
• Adjustable Minimum speed (0–30% of base)
• Adjustable Maximum speed (60–120% of base)
• Adjustable IR Compensation
• Adjustable Current Limit
• Adjustable Linear Acceleration and Deceleration
• Power interrupt relay (RC and RE versions)
• Solid state over-current output
• -10° to +45°C ambient temperature
• Line voltage compensation
• 5K ohm speed potentiometer kit included
• 50:1 speed range
• Overload capacity: 200% for one minute
• Transient voltage protection
• Voltage follower mode - isolated signal (0–12 VDC)
• Inhibit circuit–permits low power start & stop
Model Width Length Depth Weight
530
chassis
530
enclosed
6.70 in
[17.0 2 cm]
6.70 in
[17.0 2 cm]
9.00 in
[22.86 cm]
10.0 in
[25.40 cm]
2.00 in
[5.08 cm]
4.75 in
[12.07 cm]
OPTIONS
-36M option
-5 option
40.0 oz
[1.13 kg]
56.0 oz
[1.42 kg]
Base Model Options
Model
530BC
530BRC
533BC
530BRE
C – open chassis √ - Option is available N/A – Option Not available
E – NEMA 4 enclosed S - Standard Feature F – Option is available as Factory Installed only
Supply
Voltage
120/240
VAC
120/240
VAC
120/240
VAC
120/240
VAC
Motor
Voltage
90/180
VDC
90/180
VDC
90/180
VDC
90/180
VDC
Current HP Body -4 -5 -7 -15A -29B -36M -36MA -38M -38MA
10 AD C 1/ 8-2 C N/A
10 AD C 1/ 8-2 C N/A
15 ADC 1.5 /3. 0 C N/A
10 AD C 1/ 8-2 E F N/A
ü ü
ü ü
ü
N/A N/A N/A N/A N/A N/A N/A
ü
F
F
F
ü ü ü ü ü
ü ü ü ü ü
ü
F F F F
OPTION DESCRIPTION
-4: Run/Jog feature- enclosed models only
-5: Isolated 4-20mA signal follower input - loop power NOT provided
-7: Same as -5 option, with provision to add manual speed pot for Auto/Manual operation
-15A: Extended linear Acceleration & Deceleration to 30 seconds
-29B: 4PDT center block (no pass) switch motor reversing. Cuts off supply power while changing motor direction
-36M: Anti-plug/zero speed detect relay reverse with dynamic brake. Renders main drive to single voltage
(120VAC/90VDC)
-36MA: Same as -36M, with heavy duty dynamic brake resistor. For high cycle / high inertia load applications
-38M: Same as -36M except renders main drive to single voltage (240VAC/180VDC)
-38MA: Same as -38M, with heavy duty dynamic brake resistor. For high cycle / high inertia load applications
11
Loading...