Dart Controls 13DVA Instruction Manual

MODEL 13DVA Rev.A / 15DVA Rev.A HOOK-UP

WARNING

IMPROPER INSTALLATION OR OPERATION OF THIS CONTROL MAY RESULT IN INJURY TO PERSONNEL OR ELECTRONIC FAILURE. THE

CONTROL MUST BE INSTALLED AND GROUNDED IN ACCORDANCE WITH LOCAL, STATE, AND NATIONAL SAFETY CODES. AT NO TIME

SHOULD THE CIRCUIT CONTINUITY BE CHECKED BY SHORTING TERMINALS WITH A SCREWDRIVER OR OTHER METAL DEVICE.

PLEASE READ COMPLETELY BEFORE MAKING ANY ADJUSTMENTS

HOOK-UP & TERMINAL IDENTIFICATION

1) Before attempting to wire the control, make sure all power is turned off.

2) Use a normal blow fuse, wired in series with hot side of AC input, rated to 125% of motor current. Note: Both

AC lines should be fused for 240 VAC input.

CAUTION SHOULD BE USED IN SELECTING THE SIZE OF HOOK-UP WIRING. LIMIT THE VOLTAGE DROP THROUGH THE WIRING TO 5% OF

THE LINE VOLTAGE AT FULL LOAD.

3) +ARM: Connect to plus (+) Armature wire on motor. 0-90 VDC for 120 VAC input, and 0-180 VDC for 240 VAC input.

4) -ARM: Connect to minus (-) Armature wire on motor.

5) -FIELD: Connect to minus (-) Field wire of Shunt Wound Motor.

6) AC1 and AC2: 120 VAC - Connect incoming hot AC (black wire) to AC1 and neutral (white wire) to AC2

240 VAC - Connect both hot sides, one to AC1 and one to AC2.

7) +FIELD: Do not use for permanent magnet motor. This supplies +Field voltage for a Shunt Wound Motor. For motors

with dual voltage field (ie; 50/100V or 100/200V), make sure the highest value is connected.

CAUTION: DO NOT ATTEMPT TO PERFORM A HI-POT TEST ACROSS AC LINES WITH CONTROL IN CIRCUIT.

THIS WILL RESULT IN IMMEDIATE OR LONG TERM DAMAGE TO THE CONTROL.

1) Preset trimpots in the counter-clockwise (CCW) position.

ADJUSTMENTS

2) Apply power.

3) Rotate the Speedpot fully CW and adjust MAX trimpot in the CW direction until the maximum desired

speed is obtained.

4) Rotate the Speedpot fully counter-clockwise (CCW) and adjust the MIN trimpot in the CW

direction until deadband or the minimum desired speed is obtained.

5) The IR COMP trimpot is used as a regulation adjustment. If better motor regulation is needed between minimum and maximum loads, then

adjust IR COMP trimpot as follows. Rotate the Speedpot CW to the 50% position and rotate the IR COMP trimpot CW as needed to increase

regulation.

6) Recheck and readjust trimpots if necessary. Trimpot interaction with each other will be minimal.

SPEEDPOT HI

SPEEDPOT WIPER

SPEEDPOT LO

MIN

IR COMP

SPEEDPOT LO

(orange wire)

SPEEDPOT WIPER

(red wire)

SPEEDPOT HI

(white wire)

TO REMOTE

SPEEDPOT

MIN

IR COMP

-TS OPTION

+ARM

-ARM

-FIELD

AC2

AC1

MAX

+FIELD

A-1-2718B-A

LT01

MAX

+ARM

-ARM

-FIELD

AC2

AC1

+FIELD

HEATSINK DIMENSIONS & IDENTIFICATION

.592

.140

.216

2.500 +/-.050

2.055.240

.318 .178

1.261

C

L

.203

.377 DIA.
(1 HOLE)

2.126

2.326

.140 DIA.

(2 PLACES)

.750

.230

1 or 1A HOUSING*

(SIDE PROFILE)

2 or 2A HOUSING*

13DVA Rev.A /15DVA Rev.A MODEL SPECIFICATIONS

AC Input Voltage .............................................................................................. ± 10% Rated Line Voltage

Amps - DC Output ........................................................................................................ 150mA to 2 Amps

Dimensions ............................................................. 13DV1 / 15DV1: 2.80" wide, 1.30" high, 3.30" deep

Dimensions ............................................................. 13DV2 / 15DV2: 2.80" wide, 1.50" high, 3.30" deep

Input Frequency ..................................................................................................................... 50 / 60 Hertz

Input Voltage - 13DV .................................................................................................... 12 VAC or 24 VAC

Input Voltage - 15DV ................................................................................................. 120 VAC or 240 VAC

I.R. Compensation ................................................................................................. Adjustable - full range

Max. Speed .................................................................................... Adjustable (40 - 120% of Base Speed)

Min. Speed .................................................................................................... Adjustable (0 - 30% of Max)

Output Voltage - 13DV (12 or 24 VAC Input) .................................................................. 0-12 or 0-24 VDC

Output Voltage - 15DV (120 or 240 VAC Input) .......................................................... 0-105 or 0-210 VDC

Overload Capacity ........................................................................................................ 200% for 1 minute

Shunt Field Voltage - 13DV ..................................................................... 1 Amp max, 10 VDC at 12 VAC

Shunt Field Voltage - 15DV ..................................................................... 1 Amp max, 20 VDC at 24 VAC

Shunt Field Voltage - 15DV ................................................................. 1 Amp max, 100 VDC at 120 VAC

Shunt Field Voltage - 15DV ................................................................. 1 Amp max, 200 VDC at 240 VAC

Speed Control ........................................................................................... 5K Ohm Speed Potentiometer

Speed Range ........................................................................................................................................ 25:1

Speed Regulation ...................................................................................................... ± 1% of Base Speed

Temperature Range ....................................................................... -10o to 45o C. Ambient (15o to 115o F.)

Transient Protection ........................................................................................................................ G-Mov

Weight .................................................................................................. 13DV1A / 15DV1A weighs 2.64 oz.

Weight .................................................................................................. 13DV2A / 15DV2A weighs 3.03 oz.

With suitable external heatsink, current can be increased to 4 Amps. The 13DV/15DV heatsink temperature

should not exceed 70

o

C. Equivalent to 4" x 4" x 0.125" thick aluminum plate mounted to housing.

A-1-2718B-B

LT01