Technical Information
Transit Mixer Axial Piston Motor
Size 070/084/089
powersolutions.danfoss.com
Technical Information
TMM Transit Mixer Axial Piston Motor, Size 070/084/089
Revision history |
Table of revisions |
|
|
|
|
|
|
|
Date |
Changed |
Rev |
|
|
|
|
|
June 2017 |
Update to Engineering Tomorrow |
0202 |
|
|
|
|
|
Mar 2014 |
Converted to Danfoss layout – DITA CMS |
BA |
|
|
|
|
|
10 Aug 2012 |
New TMM images |
AD |
|
|
|
|
|
15 Feb 2012 |
TMM detail view added |
AC |
|
|
|
|
|
20 Jan 2012 |
Pictures` numbers were added, MMC change. |
AB |
|
|
|
|
|
08 Dec 2011 |
First edition |
AA |
|
|
|
|
2 | © Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 |
Technical Information |
|
TMM Transit Mixer Axial Piston Motor, Size 070/084/089 |
|
Contents |
|
Revisions |
|
Technical Specifications |
|
Literature reference ........................................................................................................................................................................ |
5 |
General description......................................................................................................................................................................... |
5 |
TMM fixed displacement motor sectional view.................................................................................................................... |
6 |
System schematic............................................................................................................................................................................. |
6 |
TMM technical data......................................................................................................................................................................... |
7 |
Output Speed............................................................................................................................................................................... |
9 |
System Pressure........................................................................................................................................................................... |
9 |
Case Pressure................................................................................................................................................................................ |
9 |
External Shaft Seal Pressure.................................................................................................................................................... |
9 |
Temperature................................................................................................................................................................................. |
9 |
Viscosity........................................................................................................................................................................................ |
10 |
Filtration............................................................................................................................................................................................ |
10 |
Case Drain......................................................................................................................................................................................... |
10 |
Reservoir............................................................................................................................................................................................ |
10 |
Determination of nominal motor sizes.................................................................................................................................. |
11 |
High-pressure relief valve (HPRV)............................................................................................................................................. |
11 |
Anti-cavitation valve..................................................................................................................................................................... |
12 |
Loop flushing shuttle spool........................................................................................................................................................ |
12 |
Loop flushing relief valve............................................................................................................................................................ |
12 |
Speed sensor description............................................................................................................................................................ |
13 |
Speed and temperature sensor........................................................................................................................................... |
13 |
Sensor PPU, KPP*13808.......................................................................................................................................................... |
14 |
Master Model Code |
|
TMM master model code............................................................................................................................................................ |
15 |
Operation |
|
Bearing life........................................................................................................................................................................................ |
17 |
Bearing life with no external shaft side load................................................................................................................... |
17 |
External radial shaft loads...................................................................................................................................................... |
17 |
Mounting Flange Loads............................................................................................................................................................... |
18 |
Estimating overhung load moments................................................................................................................................. |
18 |
Output shafts................................................................................................................................................................................... |
19 |
Installation drawings |
|
Dimensions....................................................................................................................................................................................... |
22 |
© Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 | 3 |
Technical Information
TMM Transit Mixer Axial Piston Motor, Size 070/084/089
4 | © Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 |
Technical Information
TMM Transit Mixer Axial Piston Motor, Size 070/084/089
Further available literature
Title |
Type |
Literature number |
|
|
|
Speed and Temperature Sensor |
Technical Information |
11046759 |
|
|
|
Hydraulic Fluids and Lubricants |
Technical Information |
520L0463 |
|
|
|
Design Guideline for Hydraulic Fluid Cleanliness |
Technical Information |
520L0467 |
|
|
|
TMM Axial Piston Motor |
Service Manual |
L1211037 |
|
|
|
This motor is designed primarily to be combined with others pumps in closed circuit system to transfer hydraulic power, especially for Transit Mixer Application.
•Innovation with reliable technology
•Loop flushing device integrated
•High pressure relieve valves integrated
•Anti-cavitation valves – optional
•Speed and temperature sensor – optional
•Speed sensor
•Metric / Inch connections
•High pressure ports for 3000 and 6000 psi on one side
•Sizes: 70 cm3, 84 cm3 and 89 cm3
TMM fixed displacement motor
© Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 | 5 |
Technical Information
TMM Transit Mixer Axial Piston Motor, Size 070/084/089
Technical Specifications
TMM cross-sectional view
Loop flushing valve
Anti-cavitation valve
High pressure relieve valve
Valve plate |
Piston |
Conical bearings |
|
|
Output shaft |
|
Cylinder block |
Fixed swashplate |
The schematic below shows the function of a hydrostatic transmission using a TMP axial variable displacement pump with electric proportional displacement control (EDC) and a TMM fixed displacement motor with integrated loop flushing device.
6 | © Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 |
Technical Information
TMM Transit Mixer Axial Piston Motor, Size 070/084/089
Technical Specifications
TMM with TMP EDC
C1 |
C2 |
|
|
|
|
|
|
L1 |
M1 |
M3 |
|
|
|
A |
|
|
|
|
|
M5 |
|
|
|
|
M4 |
|
|
|
|
|
|
|
|
B |
|
M10 |
S |
L2 |
M2 |
|
TMP |
|
|
|
L1 |
|
|
|
|
M1 |
|||||
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
A
B |
|
|
L2 |
M3 |
M2 |
|
TMM |
|
Legend: |
M3 – Charge gage port, after filtering |
A, B – System ports |
M4, M5 – Servo gage ports |
L1, L2 – Case drain ports |
M10 – Charge pump inlet pressure port |
M1, M2 – System A/B gage ports |
S – Charge inlet port |
Detailed information about ports see the section Installation drawings, pages Dimensions on page 22.
General specifications
Design |
Axial piston motor with fixed swashplate design with fixed displacement |
|
|
Direction of rotation |
Bi-directional |
|
|
Pipe connections |
Main pressure ports: ISO split flange boss |
|
|
|
Remaining ports: ISO/SAE straight thread O-ring boss |
|
|
Recommended |
Motor installation position is discretionary |
installation position |
The housing must always be filled with hydraulic fluid. . |
|
|
W Warning
The front shaft seal must not be exposed to oil pressure from outside of the unit.
© Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 | 7 |
Technical Information
TMM Transit Mixer Axial Piston Motor, Size 070/084/089
Technical Specifications
Technical data
Features |
Unit |
Size |
|
|
|
|
|
|
|
|
|
070 |
084 |
089 |
|
|
|
|
|
Displacement maximum |
cm3 |
68.3 |
83.8 |
89.0 |
|
[in3] |
[4.17] |
[5.11] |
[5.43] |
Flow at rated (continuous) speed |
l/min |
171 |
209.5 |
222.5 |
|
[US gal/min] |
[45.2] |
[55.3] |
[58.8] |
|
|
|
|
|
Torque (theoretical) |
N•m/bar |
1.09 |
1.33 |
1.42 |
|
[lbf•in/1000 psi] |
[665] |
[812] |
[867] |
|
|
|
|
|
Mass moment of inertia of |
kg•m2 |
0.0209 |
0.0209 |
0.0209 |
rotating components |
[lbf•ft2] |
[0.0159] |
[0.0159] |
[0.0159] |
Weight dry (standard) |
kg |
34.8 |
34.8 |
34.8 |
|
[lb] |
[76.9] |
[76.9] |
[76.9] |
|
|
|
|
|
Oil volume |
l [US gal] |
2 [0.53] |
2 [0.53] |
2 [0.53] |
|
|
|
|
|
Mounting flange |
SAE ISO 3019/1 flange 127-4 (SAE C), M12x1,75 |
|
||
|
|
|
|
|
Output shaft |
Spline shaft SAE, 21 teeth, pitch = 16/32 |
|
|
|
|
Spline shaft SAE, 23 teeth, pitch = 16/32 |
|
|
|
|
|
|
||
Main port configuration |
Twin ports SAE J518b Size 1, with metric or inch screws |
|
||
|
|
|
|
|
Case drain ports L1, L2 |
M22x1,5 (O-ring boss) or 7/8–14 UNF-2B |
|
|
|
|
|
|||
Other ports |
ISO straight thread O-ring boss or SAE. See Installation drawings, page |
|||
|
Dimensions on page 22. |
|
|
|
|
|
|
|
|
Operating parameters
Features |
|
Unit |
070/084/089 |
|
|
|
|
|
|
Output speed |
Minimum |
min-1 (rpm) |
100 |
|
|
Rated |
|
2500 |
|
|
|
|
|
|
|
Maximum |
|
2900 |
|
|
|
|
|
|
System pressure |
Max. working pressure |
bar |
420 [6090] |
|
|
|
[psi] |
|
|
|
Maximum pressure |
450 [6525] |
||
|
|
|||
|
|
|
|
|
|
Minimum pressure |
|
10 [145] |
|
|
|
|
|
|
Case pressure |
Rated |
bar |
3.0 |
[44] |
|
|
[psi] |
|
|
|
Maximum |
5.0 |
[73] |
|
|
|
|||
|
|
|
|
|
Lip seal external pressure |
Maximum |
|
0.4 |
[5.8] |
|
|
|
|
|
Fluid specifications
Features |
|
Unit |
070/084/089 |
|
|
|
|
Viscosity |
Intermittent 1 |
mm2/s [SUS] |
5 [42] |
|
Minimum |
|
7 [49] |
|
|
|
|
|
Recommended range |
|
12-80 [66-370] |
|
|
|
|
|
Maximum |
|
1600 [7500] |
|
|
|
|
Temperature |
Minimum (cold start) 3 |
°C [°F] |
-40 [-40] |
range 2 |
|
|
|
Recommended range |
|
60-85 [140-185] |
|
|
|
||
|
|
|
|
|
Rated |
|
104 [220] |
|
|
|
|
|
Maximum intermittent 1 |
|
115 [240] |
8 | © Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 |
Technical Information
TMM Transit Mixer Axial Piston Motor, Size 070/084/089
Technical Specifications
Fluid specifications (continued)
Features |
|
Unit |
070/084/089 |
||
|
|
|
|
||
Filtration |
Cleanliness per ISO 4406 |
|
22/18/13 |
||
(recommended |
|
|
|
||
Efficiency (charge pressure filtration) |
β-ratio |
β15-20 = 75 (β10 ≥ 10) |
|||
minimum) |
|||||
|
|
|
|||
|
|
Efficiency (suction and return line filtration) |
|
β35-45 = 75 (β10 ≥ 2) |
|
|
|
|
|
|
|
|
|
Recommended inlet screen mesh size |
µm |
100 – 125 |
|
|
|
|
|
|
|
1 |
Intermittent = Short term t < 1 min per incident and not exceeding 2 % of duty cycle based load-life |
||||
2 |
At the hottest point, normally case drain port |
|
|
||
3 |
Cold start = Short term t < 3 min, p ≤ 50 bar [725 psi], n ≤ 1000 min-1(rpm) |
|
|||
|
|
|
|
|
Minimum speed is the lowest output speed. Operating below minimum speed limits the system can be unstable.
Rated speed is the highest input speed recommended at full power condition. Operating at or below this speed should yield satisfactory product life.
Maximum speed is the highest operating speed permitted. Exceeding maximum speed reduces product life and can cause loss of hydrostatic power and braking capacity. Never exceed the maximum speed limit under any operating conditions.
Maximum working pressure is the highest recommended application pressure; and it is not intended to be a continuous pressure. Propel systems with application pressures at, or below, this pressure should yield satisfactory unit life given proper component sizing.
Maximum pressure is the highest allowable application pressure under any circumstance. Application pressures above maximum working pressure will only be considered with duty cycle analysis and factory approval.
Minimum pressure must be maintained under all operating conditions to avoid cavitation.
Under normal operating conditions, the rated case pressure must not be exceeded. During cold start, case pressure must be kept below maximum intermittent case pressure.
In certain applications, the input shaft seal may be exposed to external pressures.
The shaft seal is designed to withstand an external pressure up to 0.4 bar [5.8 psi] above the case pressure.
The case pressure limits must also be followed to ensure the shaft seal is not damaged.
High temperature limits apply at the inlet port of the motor. The motor should run at or below the maximum continuous temperature.
Cold oil generally does not affect the durability of motor components. It may affect the ability of oil to flow and transmit power. For this reason, keep the temperature at 16°C
[60 °F] above the pour point of the hydraulic fluid.
Minimum (cold start) temperature relates to the physical properties of component materials. Maximum continuous temperature is the allowed temperature at which normal life can be expected.
© Danfoss | June 2017 |
L1108123 | BC00000193en-US0202 | 9 |