Danfoss RAW 5215, RAW 5216, RTD 5215, RTD 5216 Data sheet

Data Sheet
Thermostatic Radiator Sensor, Type RAW with RTD Connection
Application
Ordering and Technical Data
The sensors are equipped with RTD connection.
RAW 5216 is identical to 5215 except for the temperature range 16 - 28 °C.
The RAW 5215 sensor incorporates a frost protection setting for maximum user flexibility.
RAW/RTD 5215/5216
The RAW series is a programme of radiator thermostats which covers all central and district heating systems.
RAW is a self-actuating proportional controller with a small P-band.
RAW radiator thermostats are designed for use in 2-pipe domestic heating systems.
Sensor range
Product Model Colour
RAW 5215 Built-in temperature sensor RAL 9016 8-28 °C 013G5215 RAW 5216 Built-in temperature sensor, limited temperature area RAL 9016 16-28 °C 013G5216
The RAW sensors also provide the option to limit the temperature range. On 013G5215 both maximum and minimum setting temperature can be limited. On 013G5216 only the maximum temperature can be limited.
The RAW design is particularly robust, with both End-Stop strength limits and sensor bending force limits being substantially above the requirements of the European Standard EN215.
Temp.
range
1)
Code no.
1)
Xp = 2 K. (The valve closes at 2 °C higher room temperature)
Accessories and Spare
Product Code no.
Parts
Theft protection 013G5287
Danfoss Heating Solutions VDFNP202 © Danfoss 03/2011 1
*
10 14 18 22 26 30 °C
*
8 12 16 20 24 28 °C
1
2
3
4
5
. . . . . .
Data Sheet Thermostatic Radiator Sensor, Type RAW with RTD Connection
Temperature Setting
Mounting
The required room temperature is set by turning the setting dial. The temperature scales show the correlation between scale values and the room temperature. The temperature values stated are for guidance only as the obtained room temperature will often be influ-enced by installation conditions.
1. 2.
= Frost protection setting
The temperature scales are stated according to European standards at Xp = 2°C. This means that
the radiator thermostats close at a sensor temperature which is 2°C higher than stated on the temperature scales.
3. 4.
An open-end spanner is used for mounting the sensor onto the valve body (1 & 2). The sensor should always be placed where the room air can circulate freely around it.
RAW5215 only
Setting the upper and lower limit
The thermostat features two tabs with which the temperature setting area can be decreased. If 4 should be max. setting, turn the thermostat to max. position (3) and press and hold right tab while turning the thermostat to 4 (3), now release tab. With the left tab the lower temperature must be turned to min. position (4).
2 VDFNP202 © Danfoss 03/2011 Danfoss Heating Solutions
Data Sheet Thermostatic Radiator Sensor, Type RAW with RTD Connection
Design and Function
1. Union nut
2. Socket
3. Setting mark
4. Auxiliary spring
5. Spindle screw
6. Spindle nut
7. Spring housing
8. Cover
9. Handle
10. Spring
11. Capsule
12. Ball
13. Bellows
14. Filling
15. Bellows ring
16. Limiter tab
Dimensions
The RAW thermostatic sensor operates with a liquid filled bellows system, which provides proportional control, as opposed to On/Off. The sensor is actuated by ambient temperature changes. The calibrated pressure in the bellows corresponds to the temperature of the charge. This pressure is balanced by the force of a regulating spring.
013G5215 013G5216
Setting L
1
L
2
* 81.6 3.7 3 84.3 6.4 5 86.2 8.3
On a rise in ambient temperature, the pressure increases in the bellows, moving the valve cone towards the “closed” position, until equilibrium exists between the bellows and spring. On a drop inambient temperature, the pressure falls, allowing the bellows to contract and the valve cone to move towards the “open” position until a state of equilibrium is re-established.
Setting L
1
L
2
"min." 82.9 5.0
3 84.3 6.4 5 86.2 8.3
Danfoss Heating Solutions VDFNP202 © Danfoss 03/2011 3
Data Sheet Thermostatic Radiator Sensor, Type RAW with RTD Connection
Danfoss A/S Heating Solutions Haarupvaenget 11 8600 Silkeborg Denmark Phone:+45 7488 8000 Fax: +45 7488 8100 Email: heating.solutions@danfoss.com www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
4 VDFNP202 © Danfoss 03/2011 Danfoss Heating Solutions
Loading...