Danfoss PAH Series, PAHT C Series, PAHT Series, PAHT G Series, PAHT 2-6.3 Service Manual

...
Service guide
PAH, PAHT, PAHT C, PAHT G pumps
PAH 2-6.3/PAHT 2-6.3/PAHT C 2-6.3 and PAHT G 2-6.3 Disassembling and assembling
HPP.danfoss.com
2
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
NOTE: If the pump is disassembled within the warranty period, the pump is no longer covered by the warranty.
Introduction
Table of Contents
Contents
Introduction .......................................................................................2
1. Disassembling the pump ................................................................3
2. Inspection .............................................................................7
2.1. Port plate and valve plate ...............................................................7
2.2. Pistons..................................................................................7
2.3. Cylinder barrel ..........................................................................8
2.4. Housing ................................................................................8
2.5. Swash plate ............................................................................8
3. Assembling .............................................................................9
4. Spare parts list for PAH / PAHT / PAHT C 2 ...............................................16
5. Spare parts list for PAHT G 2............................................................17
6. Spare parts list for PAH / PAHT / PAHT C 3.2-6.3 .........................................18
7. Spare parts list for PAHT G 3.2-6.3 ......................................................19
This document covers the instructions for disassembling and assembling the axial piston pumps PAH / PAHT / PAHT C / PAHT G 2-6.3.
Tools provided with tool set 180Z0235:
• Shaft bush, torpedo
• Press bush Ø18 (Plastic)
3
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
1. Disassembling the pump
2. Remove the parallel key and unscrew the front cover.
1. Tools required for dismantling. Caution: Avoid scratching the sealing
surface on the shaft
3. Dismantle the front cover using a vice.
4. Remove the shaft seal using two screw drivers.
Caution: Avoid scratching the sealing surface on the shaft.
5. Remove the two small O-rings from the ange. Remove the seal from the front cover using a screwdriver. 6. Unscrew the four screws for the housing.
4
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
7. Remove the housing. 8. Remove the cylinder barrel.
10.1.b. Remove the stop.10.1.a. Remove the spring
9. Remove the pistons and the retainer plate from the cylinder barrel.
NB: Items 10.1.a. and 10.1.b. concern PAH 2, PAHT 2, PAHT C 2 and PAHT G 2 only
5
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
10.2.a. Remove the retainer guide.
10.2.b. Remove the spring guide.
10.2.c. Remove the spring.
NB: The following items concern PAH 2-6.3, PAHT 2-6.3, Paht C 2-6.3 and PAHT G 2-6.3 only
NB: Items 10.2.a. through 10.2.c. concern PAH 4-6.3, PAHT 3.2-6.3, PAHT C 3.2-6.3 and PAHT G 3.2-6.3 only
12. Remove the valve plate.
11. Loosen the valve plate using two
screwdrivers. Place one of the screwdrivers in the slot of the valve plate.
6
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
13. Remove the ve O-rings and the ve back-up O-rings.
14. Remove the port plate from the ange.
15. Wash all parts and replace all seals
(inclusive shaft seal).
17. If the pump has failed, the reason for the
failure must be found and xed before the repaired pump is re-installed.
16. Inspect all parts carefully (see “Inspection”) and replace any worn parts.
Stop
Spring
Pistons
Retainer plate
Cylinder barrel
Housing with swash plate and bearing
Port plate
Valve plate
with sealing
Front cover
Flange
7
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
2. Hold a ruler against the surface of the plates and check the tightness against a light source.
1. Neither port plate nor valve plate must show any sign of wear.
3. Check that both O-rings and back-up rings are not broken and do not show severe wear.
2. Inspection 2.1. Port plate and valve plate
3. Hold a ruler against the surfaces of the piston shoes to check that the surfaces are even and smooth and without any scratches. PAHT only: It is acceptable that the (black) treated surfaces of the pistons are partly worn o.
1. The play in the ball and socket joint must not exceed 0.1 mm.
2. The thickness of the piston shoes must be at least 2.85 mm.
2.2. Pistons
8
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
2. Check that the bushings are free from seizure and large scratches, and ensure that the pistons can move freely in the bushings.
1. Check the outer bearing surface for large wear grooves (not critical).
2.3. Cylinder barrel
1. Check that the swash plate surface is smooth and without any big scratches (depth more than 0.1 mm).
2. Check the bearing (the black part) for large wear grooves (not critical).
2.4. Housing
1. Unscrew center bolt from the swash plate.Mounted swash plate:
2.5. Swash plate
9
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
Guide pin2. Remove swash plate and guide pin.
1. Lubrication:
• To prevent seizing-up, lubricate all threads with PTFE lubrication type.
• O-rings inside pump may be lubricated only with clean ltered water.
• O-rings for port ange, mounting ange and ushing valve must be lubricated.
• It is important to lubricate ALL parts to be assembled with clean ltered water (Especially all PEEK parts).
2. Parts and tools required for assembly. Check that all parts are OK. Replace all seals.
WARNING: Do not use silicone when assembling the pump. Do not reuse disassembled O-rings; they might be damaged. Always use new O-rings.
3. Assembling Important:
It is essential that the pump is serviced in conditions of absolute cleanliness. All parts must be absolute clean before mounting.
10
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
4. Mount the port plate in its right position using the pin as guide.3. Mount the O-ring on the ange.
Guide pin
6. Press the valve plate into the cylinder barrel using a piece of plastic.
5. Mount the valve plate with seals on the cylinder barrel.
8. Mount the cylinder barrel in the ange.
7. Check that the gap between the cylinder barrel and the valve plate is 1.5-2.5 mm.
11
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
9.1.a. Mount the stop.
9.1 NB: Items 9.1.a through 9.1.c concern PAH 2, PAHT 2, PAHT C 2 and PAHT G 2 only
9.1.b. Mount the spring in the centre hole.
9.1.c. Mount the retainer plate.
9.2 NB: Items 9.2.a through 9.2.d concern PAH 4-6.3, PAHT 3.2-6.3, PAHT C 3.2-6.3 and PAHT G 3.2-6.3 only
9.2.b. Mount the spring guide.
9.2.a. Mount the spring in the centre hole.
12
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
9.2.d. Mount the retainer plate on the retainer guide.
9.2.c. Mount the retainer guide on the spring guide.
11. All pistons inserted.10. Insert the pistons.
12. Place pin and place swash plate ttet on guide pin and center hole.
9.3 NB: The following items concern PAH 2-6.3, PAHT 2-6.3 and PAHT G 2-6.3 only
13
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
14. Tighten to a torque of 10 ±1 Nm.13. Place the screw in the center hole.
16. Press the housing down by hand and insert the screws.
15. Mount the pump housing using the pin as guide.
18. Mount the two O-rings in the ange and the O -ring on the front cover.17. Tighten the screws to a torque of 13 Nm.
Alignment
hole
Guide pin
14
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
20. Mount the washer with the edge pointing upwards.
19. Wet the shaft seal with water and mount it in the front cover. Ensure that it is pressed to the bottom.
22. Fit the hollow bush onto the shaft.21. Mount the spring.
23. Wet the shaft seal and slide it over the bush.
24. Use the shaft seal tool when pressing the shaft seal downwards.
15
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
25. Press the shaft seal in position. 26. Remove the bush.
27. Mount the front cover and align it to the screw holes.
28. Tighten the screws to a torque of 7 Nm.
16
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
4. Spare parts list for PAH / PAHT / PAHT C 2
180B4100 - Seal set
(PAH / PAHT 2-6.3)
180B4572 - Screw & Seal set FFKM
(PAHT c 2-6.3)
180B4112 - Cylinder barrel set
(PAH 2-6. 3)
180B4104 - Cylinder barrel set
(PAHT / PAHT C 2-6.3)
180B4101 - Valve plate set
(PAH / PAHT 2-6.3)
180B4571 - Valve plate set FFKM
(PAHT C 2-6.3)
180B4110 - Piston set
(PAH 2)
180B4102 - Piston set
(PAHT PAHT C 2)
180B4301 - Swash plate set
(PAH / PAHT / PAHT C 2))
180Z0235 - Tool set
Pos. Qnt. Designation Material
- 1 Shaft bush, torpedo x x x
- 1 Press bush x
1 1 Housing AISI 304 / PEEK
2 1 Pin AISI 316 x x
5 4 Screw AISI 316 x x
31 1 Swash plate AISI 431 x
32 1 Screw AISI 304 x
33 1 Washer AISI 304 x
34 1 Pin AISI 316 x
61 1 Cylinder barrel AISI 431 / PEEK x x
62 1 Spring AISI 304 x x
63 1 Spring guide PEEK
64 1 Retainer ball PEEK
65 1 Retainer plate 1.4301 x x
66 5 Piston AISI 431/ PEEK x x
67 1 Key AISI 316Ti x x
69 1 Stop PEEK x x
91 1 Port plate AISI 304 / PEEK x x
92 1 Valve plate AISI 431 x x
93 5 Back up ring PTFE x x x x
94 5 O-ring NBR x x* x x
121 1 Port ange AISI 304 / PEEK
122 1 O-ring NBR x
123 1 O-ring NBR x x*
124 1 Shaft seal AISI 304 / NBR x x*
125 1 End cover AISI 304 x*
126 1 Pin AISI 316 x
127 2 Screw M5 x 20 AISI 304 x x
130 1 Usit-ring x x
136 2 O-ring Ø7 x Ø1,5 NBR x x*
1 Service instruction x x x x x x x x x
* FFKM Sealing material
17
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
5. Spare parts list for PAHT G 2
180B4307 - Seal set
(PAHT G 2-6.3)
180B4311 - Cylinder barrel set
(PAHT G 2-6.3)
180B4308 - Valve plate set
(PAHT G 2-6.3)
180B4309 - Piston set
(PAHT G 2)
180B4317 - Swash plate set
(PAHT G 2)
180Z0235 - Tool set
Pos. Qnt. Designation Material
- 1 Shaft bush, torpedo - x
- 1 Press bush - x
1 1 Housing AISI 304 / PEEK
2 1 Pin AISI 316 x
5 4 Screw AISI 316 x
31 1 Swash plate AISI 431 x
32 1 Screw AISI 304 x
33 1 Washer AISI 304 x
34 1 Pin AISI 316 x
61 1 Cylinder barrel AISI 431 / PEEK x
62 1 Spring AISI 304 x
63 1 Spring guide PEEK
64 1 Retainer ball PEEK
65 1 Retainer plate 1.4301 x
66 5 Piston AISI 431/ PEEK x
67 1 Key AISI 316Ti x
69 1 Stop PEEK x
91 1 Port plate AISI 304 / PEEK x
92 1 Valve plate AISI 431 x
93 5 Back up ring PTFE x
94 5 O-ring NBR x
121 1 Port ange AISI 304 / PEEK
122 1 O-ring NBR x
123 1 O-ring NBR x
124 1 Shaft seal AISI 304 / NBR x
125 1 End cover AISI 304
126 1 Pin AISI 316
127 2 Screw AISI 304 x
136 2 O-ring NBR x
1 Service instruction x x x x x
18
180R9094 / 521B0985 / DKCFN.PI .011.N5.02 / 09.2015
6. Spare parts list for PAH / PAHT / PAHT C 3.2-6.3
180B4100 - Seal set
(PAH / PAHT 2-6.3)
180B4572 - Screw & Seal set
(PAHT C 2-6.3)
180B4112 - Cylinder barrel set
(PAH 2-6. 3)
180B4104 - Cylinder barrel set
(PAHT / PAHT C 2-6.3)
180B4101 - Valve plate set
(PAH 2-6.3 / PAHT 2-6.3)
180B4571 - Valve plate set
(PAHT C 2-6.3)
18 0B 4111- Pi st on set
(PAH 4-6 .3)
180B4103 - Piston set
(PAHT / PAHT C3.2-6.3)
180B4302 - Swash plate set
(PAHT / PAHT C 3.2)
180B4303 - Swash plate set
(PAH / PAHT / PAHT C 4)
180B4304 - Swash plate set
(PAH / PAHT PAHT C 6.3)
180Z0235 - Tool set
Pos. Qnt. Designation Material
- 1 Shaft bush, torpedo - x
- 1 Press bush - x
1 1 Housing AISI 304 / PEEK
2 1 Pin AISI 316 x x
5 4 Screw AISI 316 x x
31 1 Swash plate AISI 431 x x x
32 1 Screw AISI 304 x x x
33 1 Washer AISI 304 x x x
34 1 Pin AISI 316 x x x
61 1 Cylinder barrel AISI 431 / PEEK x
62 1 Spring AISI 304 x x
63 1 Spring guide PEEK x x
64 1 Retainer ball AISI 431 x x
65 1 Retainer plate AISI 431 x x
66 5 Piston AISI 431/ PEEK x x
67 1 Key AISI 316Ti x x
69 1 Stop PEEK
91 1 Port plate AISI 304 / PEEK x x
92 1 Valve plate AISI 431 x x
93 5 Back up ring PTFE x x x x
94 5 O-ring NBR x x* x x
121 1 Port ange AISI 304 / PEEK
122 1 O-ring NBR x x*
123 1 O-ring NBR x x*
124 1 Shaft seal AISI 304 / NBR x x*
125 1 End cover AISI 304
126 1 Pin AISI 316 x x
127 2 Screw AISI 304 x x
130 1 Usit-ring AISI 304 / NBR x x
136 2 O-ring NBR x x*
1 Service instruction - x x x x x x x x x x x
* FFKM seling material
19
180R9094 / 521B0985 / DKCFN.PI.011.N5.02 / 09.2015
7. Spare parts list for PAHT G 3.2-6.3
180B4307 - Seal set
(PAHT G 2-6.3)
180B4311 - Cylinder barrel set
(PAHT G 2-6.3)
180B4308 - Valve plate set
(PAHT G 2-6.3)
180B4310 - Piston set
(PAHT G 3.2-6.3)
180B4318 - Swash plate set
(PAHT G 3.2)
180B4319 - Swash plate set
(PAHT G 4)
180B4320 - Swash plate set
(PAHT G 6.3)
180Z0235 - Tool set
Pos. Qnt. Designation Material
- 1 Shaft bush, torpedo x
- 1 Press bush x
1 1 Housing AISI 304 / PEEK
2 1 Pin AISI 316 x
5 4 Screw AISI 316 x
31 1 Swash plate AISI 431 x x x
32 1 Screw AISI 304 x x x
33 1 Washer AISI 304 x x x
34 1 Pin AISI 316 x x x
61 1 Cylinder barrel AISI 431 / PEEK x
62 1 Spring AISI 304 x
63 1 Spring guide PEEK x
64 1 Retainer ball PEEK x
65 1 Retainer plate 1.4301 x
66 5 Piston AISI 431/ PEEK x
67 1 Key AISI 316Ti x
69 1 Stop PEEK
91 1 Port plate AISI 304 / PEEK x
92 1 Valve plate AISI 431 x
93 5 Back up ring PTFE x
94 5 O-ring NBR x
121 1 Port ange AISI 304 / PEEK
122 1 O-ring NBR x
123 1 O-ring NBR x
124 1 Shaft seal AISI 304 / NBR x
125 1 End cover AISI 304
126 1 Pin AISI 316
127 2 Screw AISI 304 x
130 1 Usit-ring AISI 304 / NBR x
136 2 O-ring NBR x
1 Service instruction x x x x x x x
© Danfoss | DCS (im) | 2015.09
180R9094 | 521B0985 | DKCFN.PI.011.N5.02 | 20
Danfoss A/S
High Pressure Pumps Nordborgvej 81 DK-6430 Nordborg Denmark
Loading...