Installation Guide
e30bg047.10
VLT® Wireless Communication Panel LCP 103
VLT® FC Series FC 102, FC 103, FC 202, FC 301/FC
302, and LD 302
1 Introduction
1.1 Items Supplied
• VLT® Wireless Communication Panel LCP 103
• Gasket
Illustration 1: VLT® Wireless Communication Panel LCP 103
1.2 Compatible Drive Series
Compatible drives have a white USB port.
• VLT® HVAC Drive FC 102
• VLT® Refrigeration Drive FC 103
• VLT® AQUA Drive FC 202
• VLT® AutomationDrive FC 301/FC 302
• VLT® Lift Drive LD 302
Danfoss A/S © 2020.02
N O T I C E
AN331428064824en-000101 / 130R0814 | 1
Installation Guide | VLT® Wireless Communication Panel LCP 103
Compatible software versions:
• VLT® HVAC Drive FC 102: 5.10
• VLT® Refrigeration Drive FC 103: 2.10
• VLT® AQUA Drive FC 202: 3.10
• VLT® AutomationDrive FC 301/FC 302 and VLT® Lift Drive LD 302: 8.03
1.3 Approvals and Certifications
FCC ID: 2ANSELCP-103
Introduction
N O T I C E
FCC COMPLIANCE NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 1 or more
of the following measures:
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/television technician for help.
-
Modifications: Any modifications made to this device that are not approved by Danfoss may void the authority granted to
-
the user by the FCC to operate this equipment. RF EXPOSURE COMPLIANCE This portable transmitter with its antenna has
shown compliance with FCC’s SAR limits for general population/uncontrolled exposure. The maximum listed SAR level is
0.22 W/kg (body). The antenna used for this device must not be co-located or operating along with any other antenna or
transmitter.
2 | Danfoss A/S © 2020.02
AN331428064824en-000101 / 130R0814
Installation Guide | VLT® Wireless Communication Panel LCP 103
Introduction
N O T I C E
TAIWAN NCC WARNING STATEMENT
Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance
transmitting power, or alter original characteristics and performance to an approved low-power radio frequency device.
The low-power radio frequency devices shall not influence aircraft security and interfere legal communications. If found, the
user shall cease operating immediately until no interference is achieved. The said legal communications, meaning radio
communications, is operated in compliance with the Telecommunications Act. The low-power radio frequency devices must be
susceptible with the interference from legal communications or ISM radio wave radiated devices.
Danfoss A/S © 2020.02
AN331428064824en-000101 / 130R0814 | 3
Installation Guide | VLT® Wireless Communication Panel LCP 103
Introduction
Illustration 2: EU Declaration of Conformity for VLT® Wireless Communication Panel LCP 103, Page 1
4 | Danfoss A/S © 2020.02
AN331428064824en-000101 / 130R0814
Installation Guide | VLT® Wireless Communication Panel LCP 103
Illustration 3: EU Declaration of Conformity for VLT® Wireless Communication Panel LCP 103, Page 2
Introduction
Danfoss A/S © 2020.02
AN331428064824en-000101 / 130R0814 | 5
Installation Guide | VLT® Wireless Communication Panel LCP 103
2 Installation
2.1 Installing the Communication Panel
Context:
N O T I C E
The VLT® Wireless Communication Panel LCP 103 is hot-pluggable and can be connected when the drive is powered on.
N O T I C E
PAIRING
Start pairing within the first 10 minutes after the installation. Failing to do so closes the broadcast or wireless identification due
to security limits with default passwords. To reconnect, power cycle the drive, or remove and reconnect the LCP 103.
Procedure
1. Mount the LCP 103 in the LCP input plug on the drive.
2. Search for MyDrive ® Connect in Google Play or Apple Store.
Installation
Illustration 4: MyDrive® Connect Launch Icon
3. Download and install the MyDrive® Connect App.
2.2 Connecting the Communication Panel
Context:
N O T I C E
The wireless SSID is the Danfoss serial ID of the drive. For example, Danfoss_019223G455 is the default wireless SSID for a drive
with the serial number 019223G455. The serial number is on the product nameplate, but is also visible in parameter 15-51
Frequency Converter Serial Number.
Wireless SSID Danfoss_019223G455
Default password Danfoss1933
6 | Danfoss A/S © 2020.02
AN331428064824en-000101 / 130R0814
Installation Guide | VLT® Wireless Communication Panel LCP 103
Procedure
1. Open the app and establish the Wi-Fi connection, see table 1 for descriptions of the white Wi-Fi LED.
2. When prompted, change the default password due to security restrictions. The password must be at least 8 and maximum 48
characters.
3. Replug the VLT® Wireless Communication Panel LCP 103 for the password to take effect. Failing to do so, allows the LCP 103 to
keep broadcasting.
4. Disconnect the app, navigate to smart device settings, and forget the network.
5. Search for the wireless network and connect with the new password.
Installation
N O T I C E
If the password is not changed, it leaves only 10 minutes for connecting and performing drive operations. After this, the
wireless connection closes.
If the wireless SSID and password are forgotten, reset the password by accessing parameter group 30-9* Wifi LCP via MCT 10 Set-up
Software or LCP 102.
2.3 LED Pattern
Table 1: Descriptions, LED Indicators
LED Pattern Description
On Solid green The drive is powered on (normal operation).
Wi-Fi Flashing white Connection pairing successful.
Solid white The smart device is connected and communication is OK.
Alarm Flashing red An alarm has occurred.
Warn Solid yellow A warning has occurred.
(1)
MS, NS1, NS2
1
MS=module status, NS1=network status, NS2=network status 2.
Flashing orange Identification of the drive when initiated through a winking command
Flashing, then solid orange Incompatible drive (LED flashes 3 times and then remains on).
2.4 Safe Control
The safe control parameter allows the drive to decide the motor behavior if the smart device, for example a tablet, communication is
lost. If the limits are set to [1] Stop motor, the motor stops. If the limits are set to [0] Do nothing, the motor continues to run. This is only
applicable when the motor is in Run state and if the motor has been started from the app.
The communication happens between the MyDrive® Connect App and the VLT® Wireless Communication LCP 103.
Parameter Limits/options
Parameter 30-97 Wifi Timeout Action [0] Do nothing
[1] Stop motor
Danfoss A/S © 2020.02
AN331428064824en-000101 / 130R0814 | 7
Installation Guide | VLT® Wireless Communication Panel LCP 103
2.5 Specifications
Standards IEEE 802.11 b/g
Frequency range 2.4~2.4835 GHz
Antenna PCB-mounted chip antenna
Security WPA2
Operating temperature -25 °C to +50 °C (-13 °F to +122 °F)
Operating humidity 5–95% RH, non-condensing
Operating mode Access point
Ingress protection IP20 (IP55 with gasket)
Electrical rating 5 V, 250 mA
Internal memory size 14 MB
Dimensions (LxWxD) [mm (in)] 131.2x66.6x23 (5.1x2.6x0.9)
Installation
Weight [g (oz)] 85.3 (2.88)
Firmware update VLT® Motion Control Tool MCT 10 software version 4.10 or higher.
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com
Danfoss A/S © 2020.02 M0022401
M0022401*
*
AN331428064824en-000101/ 130R0814
Loading...