Danfoss AMV 85, AMV 86 Data sheet

Data sheet

Actuators for three point control AMV 85, AMV 86

Description

The actuators AMV 85 and AMV 86 are used with VFM 2 (DN 150-250), VFS 2 (DN 65-100), VF2/3 (DN 125, 150) and AFQM (DN150-250) valves.

Features:

• “Self stroking” function

• Load related “Switch o“ function that prevents overloading

• Manual operation

• Diagnostic LED

Main data:

• Nominal voltage:

- 24 VAC, 230 VAC, 50 Hz/60 Hz

• Control input signal: 3-point

• Force: 5000 N

• Stroke: 40 mm

• Speed: 8 s/mm (AMV 85), 3 s/mm (AMV 86)

• Max. medium temperature: 200 °C

• Manual operation

Ordering Accessories

Actuator

Typ e

AMV 85

AMV 86

Power supply

(V~)

230 08 2G1451

230 082G14 61

Speed

(s/mm)

Code No.

08 2G1450

08 2G1460

Typ e for actuators Code No.

Additional switches (2×)

Additional switches (2×) and potentiometer (10 kΩ)

Stem heater 065Z7021

AMV 86/3/24 082H7050

AMV 86/3/230 082 H7051

AMV 85/8/24 082H7072

AMV 85/8/230 082H7071

AMV 86/3/24 082H7081

AMV 86/3/230 082H7080

AMV 85/8/24 082H7083

AMV 85/8/230 082H7082

Technical data

DEN-SMT/SI

Typ e AMV 85 AMV 86

Power supply V~ 24 AC, 230 AC ; +10 to –15%

Power consumption VA 10.5 23

Frequency Hz 50 / 60

Control input 3-point

Cl force N 5000

Max. stroke mm 40

Speed s/mm 8 3

Max. medium temperature

Ambient temperature 0 … 55

Storage and transport temperature –40 … +7 0

Protection Class I (230 V); III (24 V)

Grade of enclosure IP 54

Weight kg 9.80 10.0

- marking in accordance with the standards

VD.AB.S5.02 © Danfoss 09/2015

°C

Low Voltage Directive 73/23/EEC and 93/68/EEC, EN 60730/2/14

EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC, EN 50081-1 and EN 5008 2-1

200

Data sheet Actuators for three point control AMV 85, AMV 86

Installation

Disposal The actuator must be dismantled and the

elements sorted into various material groups before disposal.

Mechanical

The actuator should be mounted with the valve stem in either horizontal position or pointing upwards. Use the 57 mm castellated nut (supplied) to t the actuator to the valve body. While the actuator is being tted, a 8 mm Allen key can be used to tighten the pinch screw in the valve body ring to stop the valve turning.

Allow for necessary clearance for maintenance purposes.

Electrical

Electrical connections can be accessed by removing the cover. Two M16 x 1.5 cable entries are provided. Both entries are provided with a rubber grommet for use with exible cable. Note that in order to maintain the enclosure IP rating, appropriate cable glands must be used.

Wiring

230 VAC version:

Do not touch anything on the PCB! Do not remove the cover before the power supply is fully switched o.

Accessories

24 V, 230VAC, 50/60 Hz

1 0 V Neutral

24 VAC

230 VAC

Input power

supply

Output

Additional switches (2x) Additional switches (2x) and potentiometer

DEN-SMT/SI

+ 2 hidden pages