This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used underthe normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby or by an authorized distributor of Danby, andis non-transferable.
YYThe limited warranty period listed below is based upon the selection of brand name of product purchased.Any electrical parts of this product found to be defective will be repaired or replaced, including labour, at warrantor's option for the ORIGI-
NALpurchaser, covering service listed below per product selection. Consumable parts (i.e. light bulbs) are not warranted or guaranteedfor any length of time.
The product warranty coverage is as follows:Parts and Labour CoverageOne (1) YearCorrosion on Cabinet (No labour after 2nd year)Five (5) YearsStainless Steel Drum (Parts Only)Lifetime
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service must beperformed by a qualified service technician. If service is performed on the unit by anyone other than an authorized service depot, or theunit is used for commercial application, all obligations of Danby under this warranty shall be at an end.
EEEEXXXXCCCCLLLLUUUUSSSSIIIIOOOONNNNSS
SS
Save as herein provided, there are no other warranties, conditions, representations or guarantees, express or implied, made or intendedby Danby Products Limited (Canada) or Danby Products Inc. (U.S.A) or its authorized distributors and all other warranties, conditions,representations or guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or likelegislation or statute is hereby expressly excluded.
Save as herein provided, Danby Products Limited (Canada) or Danby Products Inc. (U.S.A), shall not be responsible for any damages topersons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unitand by the purchase of the unit, the purchaser does hereby agree to indemnify and save harmless Danby Products Limited from anyclaim for damages to persons or property caused by the unit.
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1111))))Power Failure.
2222))))Damage in transit or when moving the appliance.
3333))))Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4444))))Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con-ditions, (extremely high or low room temperature).
5555))))Use for commercial or industrial purposes.
6666))))Fire, water damage, theft, war,riot, hostility,acts of God such as hurricanes, floods etc.
7777))))Service calls resulting in customer education.
8888))))Damage to porcelain tubs due to foreign objects.
Proof of purchase date will be required for warranty claims; so, please retain bill of sale. In the event warranty service is required, pres-ent this document to our AUTHORIZED SERVICE DEPOT. or contact:
Cet appareil de qualité est garantie exempt de tout vice de matière première et de fabrication, s’il est utilisé dans les conditions normalesrecommandées par le fabricant.
Cette garantie n’est offerte qu’à l’acheteur initial de l’appareil vendu par Danby ou par l’un des ses distributeurs agréés et elle ne peutêtre transférée.
CCCCOOOONNNNDDDDIIIITTTTIIIIOOOONNNNSS
SSLa période de garantie limitée est basée sur le choix de la marque de fabrique du produit acheté.Toutes les pièces électriques de cet appareil qui s'avèrent défectueuses seront réparées ou remplacées, y compris la mian-d'oeuvre,
selon le choix du fabricant pour le produit choisi.
La garnatie du produit couvre:Pièces et main-d'oeuvreUn(1) an
Corrosion du caisson (aucune garantie de main-d'oeuvre après 2 ans)Cinq (5) ansCuve en acier inoxydable (Pièces seulement)Garantie à vie
S'adresser au détaillant qui a vendu l'appareil, ou à la station technique agréée de service la plus proche, où les réparations doivent êtreeffectuées par un technicien qualifié. Si les réparations sont effectuées par quiconque autre que la station de service agréée où à desfins commerciales, toutes les obligations de Danby en vertu de cette garntie seront nulles et no avenues
EEEEXXXXCCCCLLLLUUUUSSSSIIIIOOOONNNNSS
SS
En vertu de la présente, il n’existe aucune autre garantie, condition ou représentation, qu’elle soit exprimée ou tacite, de façon manifesteou intentionnelle, par Danby Products Limitée (Canada) ou Danby Products Inc. (E.- U. d’A.) ou ses distributeurs agréés. De même, sontexclues toutes les autres garanties, conditions ou représentations, y compris les garanties, conditions ou représentations en vertu detoute loi régissant la vente de produits ou de toute autre législation ou règlement semblables.
En vertu de la présente, Danby Products Limitée (Canada) ou Danby Products Inc. (E.- U. d’A.) ne peut être tenue responsable en casde blessures corporelles ou des dégâts matériels, y compris à l’appareil, quelle qu’en soit les causes. Danby ne peut pas être tenueresponsable des dommages indirects dus au fonctionnement défectueux de l’appareil. En achetant l’appareil, l’acheteur accepte de met-tre à couvert et de dégager Danby Products Limitée de toute responsabilité en cas de réclamation pour toute blessure corporelle ou toutdégât matériel causé par cet appareil.
4444))))Accident, modification, emploi abusif ou incorrect de l’appareil;
5555))))Utilisation dans un but commercial ou industriel;
6666))))Incendie, dommage causés par l’eau, vol, guerre, émeute, hostilités, cas de force majeure (ouragan, inondation, etc.);
7777))))Visites d’un technicien pour expliquer le fonctionnement de l’appareil au propriétaire.
Une preuve d’achat doit être présentée pour toute demande de réparation sous garantie. Prière de garder le reçu. Pour faire honorer lagarantie, présenter ce document à la station technique agréée ou s’adresser à:
Thank you for your trust and for buying our tumble drier. We hope it will successfully
serve its purpose for many years.
This appliance was designed for drying clothes,
for home use only.
IMPORTANT: Please read and follow all
instructions provided inside this manual and
observe all safety rules and operating
instructions before attempting to use this
product. SAVE THESE INSTRUCTIONS:
Before Use ................................................... 4
Important Warnings .................................. 4
Important Safety Instructions................... 5
Positioning and Installation....................... 6
Door ............................................................. 9
Wipe the interior of the drum with a soft cloth and
mild liquid detergent. Do not use aggressive
cleaning agent which could damage the surface.
WHEN YOU FIND YOUR APPLIANCE IS OUT
OF USE AND NO LONGER NEEDED, TRY NOT
TO BURDEN THE ENVIRONMENT WITH IT.
CALL THE NEAREST AUTHORIZED
“COLLECTING SERVICE FOR USED
APPLIANCES”.
Useful Hints
Avoid drying large laundry loads, as this causes
garments to easily crease and dry unevenly. (A
maximum drying load should not exceed 11lbs
dry-weight)
Drying very delicate laundry items such as
woolens and silk garments is not recommended
as they may shrink or lose their shape.
Synthetic curtains, fabrics with metal threads,
nylon stockings, as well as lingerie with prevailing
foam rubber components or rubber-like materials,
should be dried at a low temperature setting
(delicate laundry programs or time setting
programs). Place delicate fabrics in a laundry
sack, when drying together with other laundry.
When drying is finished, immediately remove all
laundry from the dryer to avoid excessive
creasing.
When drying laundry in the dryer, there is no
need to add conditioners. Conditioners are added
only when rinsing synthetics to neutralize static
electricity.
When buying clothes, especially underwear, do
not forget that they may shrink during washing as
well as during drying.
Clothes marked with a "no tumble dry" label, are
not suitable for tumble drying.
Energy consumption when drying laundry is
essentially increased if the spin speed of your
washing machine is set to operate lower than
800 r.p.m.
Important Warnings
• Only laundry washed with water can be dried in
this dryer. Never try to dry laundry washed or
cleaned with any flammable cleaning agents,
(e.g. benzine, trichlor ethylene) as it may cause
an explosion.
• Close supervision of children is always
necessary when any appliance is being used.
Never let children play on or near this
appliance while it is operational.
• Frequent cleaning of the lint filter is necessary
when using a clothes dryer. We recommend
cleaning the filter after each time a load is
finished. (It only takes a couple of seconds)
After cleaning, the lint filter must be reinstalled
back inside the air duct, located in the inner
door panel. Operating the dryer with damaged
filter or without the filter is dangerous and can
cause fire.
• Never let children or pets enter (the drum
of) the dryer
After use always switch the tumble dryer off
and cut the power supply to the appliance.
• All service interventions on the machine should
be left to an expert. Never attempt to service
the dryer yourself. Call an authorized service
agent if your dryer is in need of service. For the
location of the closest service agent in your
area, check the service listing enclosed with
the appliance, or contact the retailer, or contact
the manufacturer direct at 1 800 26 DANBY for
customer service.
• The data plate with all essential (technical)
information about the dryer is located on the
front side of appliance.
4
Instructions for Use
INSTRUCTIONS FOR USE
Important safety instructions
WARNING - To reduce the risk of fire, electric
shock, or injury to persons when using your
appliance, follow basic precautions, including the
following:
1. Read all instructions before using the
appliance.
2. Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted
with gasoline, dry-cleaning solvents, or other
flammable or explosive substances, as they
give off vapours that could ignite or explode.
3. Do not allow children to play on or in the
appliance. Close supervision of children is
necessary when the appliance is used near
children.
4. Before the appliance is removed from service
or discarded, remove the door to the drying
compartment.
5. Do not reach into the appliance if the drum is
moving.
6. Do not install or store this appliance where it
will be exposed to the weather.
7. Do not tamper with controls.
8. Do not repair or replace any part of the
appliance or attempt any servicing unless
specifically recommended in the usermaintenance instructions or in published userrepair instructions that you understand and
have the skills to carry out.
9. Do not use softeners or product to eliminate
static unless recommended by manufacturer
of the fabric softener or product.
10. Do not use heat to dry containing foam rubber
or similarly textured rubber-like materials.
11. Clean lint screen before or after each load.
12. Keep area around the exhaust opening and
adjacent surrounding areas free from the
accumulation of lint, dust, and dirt.
13. The interior of the appliance and exhaust duct
should cleaned periodically by qualified
service personnel.
14. Do not place items exposed to cooking oils in
your dryer. Item contaminated with cooking
oils may contribute to a chemical reaction that
could cause a load to catch fire.
Save these instructions
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of
least resistance for electric current. This
appliance is equipped with a cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed and
grounded in accordance with all local cordes and
ordinances.
WARNING-Improper connection of the
equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the appliance is properly grounded.
Do not modify the plug provided with the
appliance-if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
Instructions for Use
5
INSTALLATION INSTRUCTIONS
Positioning and Installation
Your clothes dryer must be placed in a room with
adequate ventilation.
Choosing the Right Place
The most appropriate space is a room with a
window or built-in ventilation fan (Figure 1).
In closed, smaller rooms without adequate
ventilation there is too much moisture in the air,
the drying time is increased and so is energy
consumption.
If during the drying procedure there isn't
adequate ventilation in the room, we recommend
you direct moist air out in the open by means of
vent pipe (Fig. 2).
1
Vent pipe can be bought in any local hardware
store.
Positioning
This dryer is a self standing appliance and can
stand alone, or it can be placed either together
with a washing machine or in the kitchen as a
kitchen unit.
If the floor is uneven, use the adjustable feet to
level the machine.
3
Undo the nuts. Rotate the feet to level the
machine (fig. 3).
Lock the nuts (fig. 3a).
• Do not remove the adjustable feet. The
machine must be placed horizontally.
• Do not put the dryer on a thick rug thus
preventing the possibility of air circulation.
2
3a
Moist Air Outlet
The ventilation opening for venting out humid air,
is located at the rear side of the dryer. Fig. 4-5
(bottom left-hand corner) The ventilation opening
is designed to accept standard 4 inch, flexible or
solid exhaust pipe. (not included with the dryer)
The ventilation exhaust can be purchased at any
local hardware store.
The distance between the dryer and venting
opening (air duct or window) must not exceed 80
inches, otherwise condensation can accumulate
in the tube, (Fig 5).
1 Solid Piping
2 Flexible pipe
6
Instructions for Use
INSTALLATION INSTRUCTIONS
Connecting to power supply
IMPORTANT NOTE: This dryer does not come
complete with an electrical power cord. Electrical
power cord kits must be purchased by the
consumer and are available at most local
hardware stores. Before purchasing a power
cord kit for your dryer, you must first establish
which type of power cord plug is required
(compatible) to fit the electrical receptacle in your
laundary room. i.e. 3 wire - 4 wire. (See Fig. 6)
When purchasing a 3-wire or 4-wire power cord
kit with strain relief, make sure the cord meets
the following requirements:
• UL listed dryer cord kit
• 240 V minimum rated
• 30 A rated
• type SRD or SRDT
• minimim five feet long
• closed-loop terminals or open-end spade lugs
with upturned ends
This dryer has a pre-installed (rear mount)
external junction box to facilitate easy connection
of the power cord kit with suitable plug.
an area where local codes do NOT permit
grounding through the neutral. Use »FOURWIRE CONNECTION« instructions.
Four-wire connection
Fig. 6
Electrical connection
WARNING:
This dryer is manufactured with the cabinetground conductor connected to the
NEUTRAL (center) of the supply cord at the
terminal block.
Only a 4-conductor cord shall be used when
the appliance is installed in a mobile home or
Junction box
Fig. 7
To connect power cord:
• Remove the screws from the cover of the
junction box located at the top rear of the dryer.
• Loosen/remove the two screws on the strain
relief clamp and remove from 4-wire supply
cord.
• The strain relief splits into two indentical parts.
• Insert the large flange of both sections into the
hole located on the left side of the junction box
housing. The short flange of both sections and
screws must remain positioned on the external
side of the junction box housing.
Instructions for Use
7
INSTALLATION INSTRUCTIONS
• Insert the 4- wire supply cord through both
sections of the strain relief and re-install strain
relief screws, do not fully tighten until electrical
connections are complete.
• Attach the power cord ground conductor (green
wire) to the ground terminal marked with the
ground symbol. Tighten screw until ground
conductor is secure. (See Fig. 7)
• Attach the power cord neutral conductor (white
wire) to the neutral terminal. (marked N)
Tighten screw until neutral conductor is secure.
(See Fig. 7)
• Attach the power cord phase conductor (black
wire) to the phase terminal (marked L3).
Tighten screw until power conductor is secure.
(See Fig. 7)
• Attach the power cord phase conductor (red
wire) to the phase terminal (marked L1).
Tighten screw until power conductor is
secure.(See Fig. 7)
• Tighten the screws on the strain relief so that
the power cord cannot be moved.
• Re-install the cover of the junction box and
secure with four screws removed earlier.
• The dryer is now ready to be connected to the
power supply receptacle.
Three-wire connection
Junction box
Fig. 8
To connect power cord:
• Remove the screws from the cover of the
junction box located at the top rear of the dryer.
• Loosen/remove the two screws on the strain
relief clamp and remove from 3-wire supply
cord.
• The strain relief splits into two indentical parts.
• Insert the large flange of both sections into the
hole located on the left side of the junction box
housing. The short flange of both sections and
screws must remain positioned on the external
side of the junction box housing.
• Insert the 3- wire supply cord through both
sections of the strain relief and re-install the
strain relief screws, do not fully tighten until
electrical connections are complete.
• Attach the power cord ground conductor (green
wire) to the ground terminal marked with the
ground symbol. Tighten screw until ground
conductor is secure. (See Fig. 8)
• Attach the two remaining power cord phase
conductors ( left = black wire and right = red
wire ) to the phase terminals (marked L3 & L1).
Tighten screws so that the power conductors
are secure. (See Fig. 8)
• Tighten the screws on the strain relief so that
the power cord cannot be moved.
• Re-install the cover of the junction box and
secure with four screws removed earlier.
• The dryer is now ready to be connected to the
power supply receptacle.
Note:
The receptacle should be located so that the plug
and receptacle will be accessible with the dryer in
its installed position.
Additional Grounding Procedure
Some local codes may require a separate
ground. In such cases, the required accessory
ground wire, clamp and screw must be
purchased separately.
Never ground the dryer to plastic plumbing lines,
gas lines or hot water pipes.
8
Instructions for Use
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.