Danby DAC10011, DAC10011E User Manual

Danby Products Limited, Ontario, Canada N1H 6Z9

Danby Products Inc., Findlay, Ohio, USA 45840

Model • Modèle • Modelo

• Owner’s Use and Care Guide

• Guide d’utilisation et soins de Propriètaire

AIR CONDITIONER
CLIMATISEUR

V1 11.10 DM

DAC10010E / DAC10011E
DAC12010E

Contents

CAUTION:

PRECAUTION:

Read and follow all safety rules and operat­ing instructions before first use of this prod­uct.

Veuillez lire attentivement les consignes de
sécurité et les instructions d’utilisation avant
l’utilisation initiale de ce produit.

CLIMATISEUR

Guide d'utilisation et d'entretien ........................

• Bienvenue

• Consignes de Sécurité Importantes

• Caractéristiques

• Installation

• Consignes d’utilisation

• Soins et Entretien

• Dépannage

• Garantie

2-17

AIR CONDITIONER

Owner’s Use and Care Guide .............................

• Welcome

• Important Safety Information

• Features

• Installation

• Operation Instructions

• Care and Maintenance

• Troubleshooting

• Warranty

Model • Modèle DAC10010E / DAC10011E / DAC12010E

18-33

Welcome

Thank you for choosing a Danby appliance to provide you and your family with all of the “Home Comfort” requirements
of your home, cottage, or office. This Owner’s Use and Care Guide will provide you with valuable information necessary
for the proper care and maintenance of your new appliance. If properly maintained, your Danby appliance will give you
many years of trouble free operation. Please take a few moments to read the instructions thoroughly and familiarize
yourself with all of the operational aspects of this appliance.

For easy reference, may we suggest you attach a copy of your sales slip/receipt to this page, along with the following
information, located on the manufacturers nameplate on the side of the unit.

NOTE: THIS UNIT IS NOT DESIGNED FOR “THROUGH-THE-WALL” INSTALLATION.

Model Number:

Serial Number:

Date of Purchase:

This information will be necessary if your unit requires servicing and/or for general inquiries. To contact a Customer

Service Representative, call Danby TOLL FREE: 1-800-263-2629

2

WARNING

Improper connection of the grounding plug can result in risk of
Fire, Electric Shock and/or injury to Persons associated with the
appliance. Check with a qualified service representative if in doubt
that the appliance is proplery grounded.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

ELECTRICAL
SPECIFICATIONS

FOR YOUR SAFETY: Read these instructions carefully before operating the unit.

1) All wiring must comply with local and national electrical codes and must

be installed by a qualified electrician. If you have any questions
regarding the following instructions, contact a qualified electrician.

2) Check available power supply and resolve any wiring problems

BEFORE installing and operating this unit.

3) This 115V air conditioner uses 10.2 or less nameplate amps and may

be used in any properly wired, general purpose household receptacle.
See Table 1 for specifications for individual branch circuit.

4) For your safety and protection, this unit is grounded through the power

cord plug when plugged into a matching wall outlet. If you are not sure
whether your wall outlet is properly grounded, please consult a qualified
electrician.

5) The wall outlet must match the 3-prong plug on the service cord
supplied with the unit. DO NOT use plug adapters. See Table 2 for
receptacle and fuse information. If it is necessary to use an extension
cord to connect your air conditioner, use an approved “air
conditioner” extension cord only (available at most local hardware
stores).

6) The rating plate on the unit contains electrical and other technical data.
The rating plate is located on the right side of the unit, above the power
cord.

3

TABLE 1

Suggested Individual Branch Circuit

Nameplate Amps *AWG Wire Size

8.8 to 10.2 14

AWG- American Wire Gauge

*Based on copper wire at 60°C temperature rating.

TABLE 2

Receptacle and Fuse Types
Rated Volts 125

Amps 15
Wall Outlet

Fuse Size 15
Time Delay Fuse Plug Type

(or Circuit Breaker)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

ENERGY SAVING TIPS

FOR YOUR SAFETY: Read these instructions carefully before operating the unit.

Your Danby appliance is designed to be highly efficient in energy
savings. Follow these recommendations for greater efficiency.

1) Select a thermostat setting that suits your comfort needs and leave at

that chosen setting.

2) The air filter is very efficient in removing airborne particles. Keep the air

filter clean at all times. (usually cleaned every 2 weeks depending on
indoor air quality).

3) Use drapes, curtains or shades to keep direct sunlight from penetrating

and heating the room, but do not allow drapes or curtains to obstruct
the air flow around the unit.

4) Start your air conditioner before the outdoor air becomes hot and

uncomfortable, to avoid an initial period of discomfort while the unit is
cooling off the room.

5) When outdoor temperatures are cool enough, use HIGH or LOW FAN

only. This circulates indoor air, providing some cooling comfort, and
utilizes less electricity than when operating on a cooling setting.

4

Features

Air FIlter

Exterior
Air Inlet

Cabinet

Interior Air Inlet

Control Panel

Fresh Air Ventilation Switch

(open for Fan only operation)

Installation Instructions

CAUTION

Because the compressor is located on the controls side of the unit
(left side), this side will be heavier and more awkward to manipu­late. Inadequate support on control side of the unit can result in
personal injury and damage to your unit and property. Therefore, it
is recommended that you have someone assist you during the
installation of this unit.

TOOLS NEEDED FOR INSTALLATION:

• Screw Drivers: Phillips and flat head.

• Power Drill: 1/8” (3.2mm) diameter drill bit.

• Pencil

• Measuring Tape

• Scissors

• Carpenters Level

NOTE: Save the shipping carton and packing materials for future storage
or transportation. From carton, remove the plastic bag containing the
installation hardware kit necessary for the installation of your air
conditioner. Please check the contents of hardware kit against the corre­sponding model check list, prior to installation of the unit. See Fig. 1.

ELECTRIC SHOCK HAZARD

To avoid the possibility of personal
injury, disconnect power to the unit
before installing or servicing.

NOTE: Your Room Air Conditioner is
designed for easy installtion in a single or
double-hung window. This unit is NOT
designed for vertical (slider type) windows
and/or through-the-wall applications.

Interior Air Outlet

Installation Instructions

Fig. 1

INSTALLATION
HARDWARE

LOCATION

A) This room air conditioner is designed to fit easily into a single or double

hung window. However, since window designs vary, it may be
necessary to make some modifications for safe, proper installation.

B) Make sure window and frame are structurally sound and free from dry

and rotted wood.

C) For maximum efficiency, install the air conditioner on a side of the

house or building which favours more shade than sunlight. If the unit is
in direct sunlight, it is advisable to provide an awning over the unit.

D) Provide sufficient clearance around the cabinet to allow for ample air

circulation through the unit (See Fig. 2). The rear of the unit should be
outdoors and not in a garage nor inside a building. Keep unit as far
away as possible from obstacles/obstructions and at least 30” above
the floor or ground. Curtains and other objects within a room should be
prevented from blocking the air flow.

E) Be certain the proper electrical outlet is within reach of the installation.

Use only a single outlet circuit rated at 15 amps. All wiring should be in
accordance with local and national electrical codes.

F) DO NOT install unit where leakage of combustible gas is suspected.

Your air conditioner may fail to operate in air containing oils (including
machine oils), sulfide gas, near hot springs, etc.

NOTE: Your unit is designed to evaporate condensation under normal
conditions. However, under extreme humidity conditions, excess conden­sation may cause basepan to overflow to the outside. The unit should be
installed where condensation run-off cannot drip on pedestrains or neigh­boring properties.

5

3/4in. (19.1mm)
screws (7)

Safety Lock (1)

3/8in. (9.5mm) screws
(4) *Factory installed

on some models

“L” Shaped
mounting
bracket (1)

* Factory installed

on some models

Sash bracket (2)

Adhesive
Foam Seal(1)

Side Curtain LH (1)

Side Curtain RH (1)

LOCATION

Installation Instructions

Awning

Fence,
wall, or
other
obstacle

Ground

Side
Obstruction

20”
Min

30”
Min

20”
Min

12” Min

Fig. 2

1) Assembly of the Upper Channel to Cabinet.

(Factory installed on some units)

• “L” Shaped Top Channel: Install the “L” shaped channel to the top of the

cabinet as shown in Fig. 3, using four (4) 3/8” screws.

2) Assembly of the Side Curtains to Cabinet.

• Extend the shutter from the shutter frame and slide it into the shutter tabs

on the side channel of the air conditioner, as shown in Fig. 4.

• Slide the shutters into the top (“L” Shaped) and bottom (“U” Shaped)
channels. The shutters are identified (on frame) as left and right.

3) Completing the Installation

• Cut the foam (non adhesive) sealing strip to fit the area of the window sill

that the air conditioner will rest on.

3/8” screws

“L” shaped mounting
bracket

“U” shaped Channel
(Factory Installed)

Slide down into tabs

Shutter tabs
Shutter
Shutter frame

Fig. 3

Fig. 4

6

7

Installation Instructions

3) Completing the Installation (cont)

• Carefully place the air conditioner into the window with the “L” shaped
mounting bracket (on top) positioned in front of the upper window sash.
The bottom of the cabinet should be positioned on the “recessed” portion
of the window frame. Pull the window down until it rests just behind the
front flange of the (top) “L” shaped mounting bracket (See Fig. 5).

• Expand the shutter frames (fully) on each side and secure the top of the
frames to the window sash using one 3/4” screw on each side and one in
the “L” shaped mounting bracket (Fig. 5).

• Secure the shutter clamp on each side of the (lower) shutter and secure

to window sill using one 3/4” screw on each side (Fig. 5).

• Place the second foam sealing strip to fit the opening between the inside
and outside windows, then attach the safety lock to the outside window
frame using one 3/4” screw (See Fig. 6).

PLEASE NOTE: Window applications come in a variety of different styles.
Therefore, it may be necessary to modify or improvise your particular
installation.

Window sash

“L” Shaped
Mounting
Bracket

Shutter clamps

3/4” screws

Fig. 5

Safety Lock

3/4” screw

Foam Seal

Fig. 6

Operating Instructions

KEY PAD FEATURES

8

LED DISPLAY: Displays the following information independently;Set

Temperature, Ambient RoomTemperature and Auto Timer On/Off settings.

POWER: Turns unit On/Off.

MODE: Allows you to scroll through and select the desired operating

mode; Cool , Dry , Fan Only and *Auto .The selected mode will be denot­ed by the adjacent indicator light.*‘Auto’is a pre-set factory program that
automatically defines the mode (Cool or Dry) and fan speed based on the
set temperature.

FAN SPEED: Select from four different fan settings;Low , Medium ,

High and Auto during Cool and Fan Only mode. Please note: During ‘Dry’
mode the fan speed is automatically defined .

ENERGY SAVER: Automatically cycles the fan on and off while the

compressor is not in use.

TEMP / TIMER CONTROL: Used to increase or decrease

the Temperature setting in 1°C / °F increments, and Auto-Timer On/Off set­tings in 30min./1hr. increments. Note: This appliance allows you select the
temperature scale to be displayed in either “Celsius” or Fahrenheit”
according to your preference.To change the temperature scale displayed
on the electronic display, press both the “Temp/Timer”adjust arrows simul­taneously to alternate between “Celsius” & “Fahrenheit”.

CHECK FILTER: The adjacent indicator light will illuminate as a

reminder to clean the air conditioner filter (see page 9) Once the filter has
been cleaned and replaced, depress the Check Filter button in order to
resume operation.

SLEEP MODE: When activated, the current set temperature is gradu-

ally increased over a one (1) hour period then maintained for seven (7)
hours. Once the program is complete, the air conditioner will resume to its
previous set temperature (before sleep mode was activated). This feature
is mean to be used during the night time hours to prevent the room from
getting too cold (while you sleep) and results in less compressor running
time and reduced energy consumption. Sleep mode may be cancelled by
depressing the Sleep Mode button while the program is running.

AUTO-TIMER: Used to initiate the Auto On/ Auto Off timer.

While the Air Conditioner is off (Auto-On):

1) Press the Auto-Timer button once and the adjacent Auto-On indicator

light will illuminate.

2) Use the Temp/Timer control cursors to select a delayed On time of

up to 24 hours.

3) Select the appropriate mode under which you want the unit to operate

(Auto-Cool-Dry-Fan Only)

4) Select the fan speed setting.

5) The time you selected will appear in the LED display.

While the Air Conditioner is on (Auto-Off):

1) Press the Auto-Timer button twice and the adjacent Auto-Off indicator

light will illuminate.

2) Use the Temp/Timer control cursors to select a delayed Off time of up

to 24 hours.

3) The time you selected will appear in the LED display. The Auto On and

Auto Off timer can operate during the same program by defining the
Auto-Off parameters immediately after the Auto On parameters.The
Auto-Timer may be cancelled at any time by turning the unit On/Off.

MODE

Auto

Auto

68

Temp / Timer

Control

Check

Filter

Mode

Selector

Energy

Saver

LED
Display

Auto
Timer

Sleep
Mode

Fan
Speed

Power
Button

Operating Instructions

USING THE REMOTE
CONTROL

Location of the remote controller.

• Use the remote controller within a distance of 5
meters from the appliance, pointing it towards
the receiver. Reception is confirmed by a beep.

O

N

/

O

F

F

M

O

D

E

T

E

M

P

U

P

T

E

M

P

D

O

W

N

S

W

I

N

G

F

A

N

T

I

M

E

R

S

L

E

E

P

5m

CAUTION

• The air conditioner will not operate if curtains, doors or other
materials block the signals from the remote controller to the
indoor unit.

• Prevent any liquid from falling into the remote controller. Do not
expose the remote controller to direct sunlight or heat.

• If the infrared signal receiver on the indoor unit is exposed to
direct sunlight, the air conditioner may not function properly. Use
curtains to prevent the sunlight from falling on the receiver.

• If other electrical appliances react to the remote controller, either
move these appliances or call the service depot.

REMOTE CONTROLLER
SPECIFICATIONS

Model

Rated Voltage

Lowest Voltage of
CPU Emitting Signal

Signal Receiving Range

Environment

R15A, R15B, R15C

3.0V(Button cell: CR2025)

2.0V

5m

-5°C ~ 60°C

9

Operating Instructions

ON/OFF button

TEMP UP button

FAN button

CLEAN AIR button
(on some models)

ENERGY SAVER
button

MODE button

TEMP DOWN button

TIMER button

SLEEP button

Operation starts when
this button is pressed
and stops when the
button is pressed again.

Push this button to
increase the tempera­ture setting in 1°C
increments to 30°C.

Used to select the fan
speed in three steps:

LOW

MED

HIGH

When this button is
pressed, the ion genera­tor is energized and will
help remove pollen and
impurities from the air.

Press this button to
activate the Energy sav­ing mode. Press it again
to stop the funtion.

Each time you press
this button, a mode is
selected in a sequence
that goes from AUTO,
HEAT (cooling and heat­ing models only) COOL,
DRY, FAN and back to
AUTO.

Push this button to
decrease the indoor
temperature setting in
1°C increments to 17°C.

Push this button to
activate the “Auto
Start” or “Auto Stop”
program from 0-12
hours (1 hour increments)

Press this button to
activate the Sleep
mode. This function is
available on COOL,
HEAT or AUTO mode
only and maintain the
most comfortable
temperature for you.

REMOTE
CONTROLLER
BUTTONS

ON/OFF button

TEMP UP button

FAN button

SWING button

MODE button

TEMP DOWN button

TIMER button

SLEEP button

Operation starts when
this button is pressed
and stops when the
button is pressed again.

Push this button to
increase the tempera­ture setting in 1°C
increments to 30°C.

Used to select the fan
speed in three steps:

LOW

MED

HIGH

When this button is
pressed, the vertical lou­vres will swing automati­cally from side to side.
Press it again to deacti­vate the "SWING" fea­ture.

Each time you press
the button, a mode is
selected in a sequence
that goes from AUTO,
HEAT (cooling and heat­ing models only) COOL,
DRY, FAN and back to
AUTO.

Push this button to
decrease the indoor
temperature setting in
1°C increments to 17°C.

Push this button to
activate the “Auto
Start” or “Auto Stop”
program from 0-12
hours (1 hour increments)

Press this button to
activate the Sleep
mode. Press again to
stop the function. This
function is available on
COOL, HEAT or AUTO
mode only and maintain
the most comfortable
temperature for you.

Models:

R15A
R15B

Models:

R15C

NOTE: Modle R15B does not have
CLEAN AIR feature.

10

ON/OFF

TEMP

UP

FAN

CLEAN
AIR

S

ENERGY

SAVER

MODE

TEMP
DOWN

TIMER

SLEEP

ON/OFF

TEMP

UP

FAN

SWING

MODE

TEMP
DOWN

TIMER

SLEEP