Page 1
DAIKIN ROOM AIR CONDITIONER
Operation Manual
MODELS
FDXS25EAVMB FDKS25EAVMB
FDXS35EAVMB FDKS35EAVMB
FDXS50CVMB FDKS50CVMB
FDXS60CVMB FDKS60CVMB
English
Deutsch
Français
Nederlands
Español
Italiano
ΕλληνικÜ
Portugues
Рóссêий
Türkçe
Page 2
CONTENTS
READ BEFORE OPERATION
Safety precautions ......................................... 2
Names of parts............................................... 4
Preparation Before Operation ........................ 7
OPERATION
AUTO · DRY · COOL · HEAT · FAN
Operation ..................................................... 10
POWERFUL Operation ................................ 12
OUTDOOR UNIT QUIET Operation............. 13
HOME LEAVE Operation ............................. 14
TIMER Operation ......................................... 16
Note for Multi System................................... 18
CARE
Care and Cleaning ....................................... 20
TROUBLE SHOOTING
Trouble Shooting.......................................... 22
1
Page 3
READ BEFORE OPERATION
Safety precautions
Keep this manual where the operator can easily find them.
•
Read this manual attentively before starting up the unit.
•
For safety reason the operator must read the following cautions carefully.
•
This manual classifies precautions into WARNING and CAUTION. Be sure to follow all precautions below: they are all
•
important for ensuring safety.
WARNING
If you do not follow these instructions exactly, the unit may
cause property damage, personal injury or loss of life.
Never do. Be sure to follow the instructions.
Be sure to earth the air conditioner.
Never touch the air conditioner (including the remote
controller) with a wet hand.
If you do not follow these instructions exactly, the unit may
cause minor or moderate property damage or personal injury.
Never cause the air conditioner (including the remote
controller) to get wet.
CAUTION
WARNING
In order to avoid fire, explosion or injury, do not operate the unit when harmful, among which flammable or
•
corrosive gases, are detected near the unit.
It is not good for health to expose your body to the air flow for a long time.
•
Do not put a finger, a rod or other objects into the air outlet or inlet. As the fan is rotating at a high speed, it will
•
cause injury.
Do not attempt to repair, relocate, modify or reinstall the air conditioner by yourself. Incorrect work will cause electric
•
shocks, fire etc.
For repairs and reinstallation, consult your Daikin dealer for advice and information.
The refrigerant used in the air conditioner is safe. Although leaks should not occur, if for
•
some reason any refrigerant happens to leak into the room, make sure it does not come in
contact with any flame as of gas heaters, kerosene heaters or gas range.
If the air conditioner is not cooling (heating) properly, the refrigerant may be leaking, so call your dealer.
•
When carrying out repairs accompanying adding refrigerant, check the content of the repairs with our service staff.
Do not attempt to install the air conditioner by your self. Incorrect work will result in water leakage, electric shocks or
•
fire. For installation, consult the dealer or a qualified technician.
In order to avoid electric shock, fire or injury, if you detect any abnormally such as smell of fire, stop the operation and
•
turn off the breaker. And call your dealer for instructions.
Depending on the environment, an earth leakage breaker must be installed. Lack of an earth leakage breaker may
•
result in electric shocks or fire.
The air conditioner must be earthed. Incomplete earthing may result in electric shocks. Do not connect the
•
earth line to a gas pipe, water pipe, lightning rod, or a telephone earth line.
CAUTION
In order to avoid any quality deterioration, do not use the unit for cooling precision instruments, food, plants,
•
animals or works of art.
Never expose little children, plants or animals directly to the air flow.
•
2
Page 4
Do not place appliances which produce open fire in places exposed to the air flow from the unit or under the indoor
•
unit. It may cause incomplete combustion or deformation of the unit due to the heat.
Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or trouble.
•
Do not stand or sit on the outdoor unit. Do not place any object on the unit to avoid injury, do not remove the fan guard.
•
Do not place anything under the indoor or outdoor unit that must be kept away from moisture. In certain conditions,
•
moisture in the air may condense and drip.
After a long use, check the unit stand and fittings for damage.
•
Do not touch the air inlet and alminum fins of outdoor unit. It may cause injury.
•
The appliance is not intended for use by young children or infirm persons without supervision.
•
Young children should be supervised to ensure that they do not play with the appliance.
•
To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner is used together with the
•
air conditioner.
Before cleaning, be sure to stop the operation, turn the breaker off or pull out the supply cord.
•
Do not connect the air conditioner to a power supply different from the one as specified. It may cause trou-
•
ble or fire.
Arrange the drain hose to ensure smooth drainage. Incomplete draining may cause wetting of the building, furniture
•
etc.
Do not place things that must be kept dry under the indoor unit. Water may drip from the indoor unit if the humidity is
•
80% or above or when the drain outlet is clogged or the air-filter is dirtied.
Do not place objects in direct proximity of the outdoor unit and do not let leaves and other debris accumulate around
•
the unit.
Leaves are a hotbed for small animals which can enter the unit. Once in the unit, such animals can cause malfunctions, smoke or fire when making contact with electrical parts.
Do not operate the air conditioner with wet hands.
•
Do not wash the indoor unit with excessive water, only use a slightly wet cloth.
•
Do not place things such as vessels containing water or anything else on top of the unit. Water may pene-
•
trate into the unit and degrade electrical insulations, resulting in an electric shock.
Installation site.
■
To install the air conditioner in the following types of environments, consult the dealer.
Places with an oily ambient or where steam or soot occurs.
•
Salty environment such as coastal areas.
•
Places where sulfide gas occurs such as hot springs.
•
Places where snow may block the outdoor unit.
•
The drain from the outdoor unit must be discharged to a place of good drainage.
Consider nuisance to your neighbours from noises.
■ For installation, choose a place as described below.
A place solid enough to bear the weight of the unit which does not amplify the operation noise or vibration.
•
A place from where the air discharged from the outdoor unit or the operation noise will not annoy
•
your neighbours
.
Electrical work.
For power supply, be sure to use a separate power circuit dedicated to the air conditioner.
•
System relocation.
Relocating the air conditioner requires specialized knowledge and skills. Please consult the dealer if reloca-
•
tion is necessary for moving or remodeling.
3
Page 5
Names of parts
■ Indoor Unit
1
45
2
3
6
8
7
4
9
10
Page 6
■ Outdoor Unit
11
12
15
■
Indoor Unit
1. Air outlet
2. Air outlet grille:
Appearance of the Air outlet grille and Air inlet
•
grille may differ with some models.
3. Receiver
4. Suction grille:
Appearance of the suction grille and Air inlet
•
grille may differ with some models.
5. Air inlet
6. Room temperature sensor:
It senses the air temperature around the unit.
•
7. Operation lamp (green)
8. TIMER lamp (yellow):
9. HOME LEAVE lamp (red):
Lights up when you use HOME LEAVE
•
operation. (page 14.)
(Field supply)
(Option)
(page 16.)
13
14
10. Indoor Unit ON/OFF switch:
Push this switch once to start operation.
•
Push once again to stop it.
This switch is useful when the remote controller
•
is missing.
•
The operation mode refers to the following table.
Mode
FDKS COOL
FDXS AUTO
Temperature
setting
22°C
25°C
Air flow
rate
AUTO
AUTO
■
Outdoor Unit
11. Air inlet:
12. Refrigerant piping and inter-unit cable
13. Drain hose
Appearance of the outdoor unit may differ from some models.
(Back and side)
14. Earth terminal:
It is inside of this cover.
•
15. Air outlet
5
Page 7
■ Remote Controller
2
3
4
7
8
1
5
6
9
10
12
11
< ARC433B69, B76 >
1. Signal transmitter:
It sends signals to the indoor unit.
•
2. Display:
It displays the current settings.
•
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. HOME LEAVE button:
HOME LEAVE operation (page 14.)
4. POWERFUL button:
POWERFUL operation (page 12.)
5. TEMPERATURE adjustment buttons:
It changes the temperature setting.
•
6. ON/OFF button:
Press this button once to start operation.
•
Press once again to stop it.
13
15
14
7. MODE selector button:
It selects the operation mode.
•
(AUTO/DRY/COOL/HEAT/FAN) (page 10.)
8. QUIET button:
QUIET operation (page 13.)
9. FAN setting button:
It selects the air flow rate setting.
•
10. ON TIMER button:
11. OFF TIMER button:
12. TIMER Setting button:
It changes the time setting.
•
13. TIMER CANCEL button:
It cancels the timer setting.
•
14. CLOCK button:
15. RESET button:
Restart the unit if it freezes.
•
Use a thin object to push.
•
OUTDOOR UNIT
(page 17.)
(page 16.)
(page 9.)
6
Page 8
Preparation Before Operation
■ To set the batteries
1. Slide the front cover to take it off.
2. Set two dry batteries (AAA).
3. Set the front cover as before.
Position + and
– correctly!
2
3
1
ATTENTION
■
About batteries
When replacing the batteries, use batteries of the same type, and replace the two old batteries
•
together.
When the system is not used for a long time, take the batteries out.
•
We recommend replacing once a year, although if the remote controller display begins to fade or if
•
reception deteriorates, please replace with new alkali batteries. Do not use manganese batteries.
The attached batteries are provided for the initial use of the system.
•
The usable period of the batteries may be short depending on the manufactured date of the air
conditioner.
7
Page 9
Preparation Before Operation
■ To operate the remote
controller
To use the remote controller, aim the transmitter
•
at the indoor unit. If there is anything to block
signals between the unit and the remote controller, such as a curtain, the unit will not operate.
Do not drop the remote controller. Do not get it wet.
•
The maximum distance for communication is
•
about 4m.
■ To fix the remote controller
holder on the wall
1. Choose a place from where the signals reach the unit.
Receiver
2. Fix the holder to a wall, a pillar, etc.
with the screws supplied with the
Remote controller
holder
holder.
3. Place the remote controller in the
Set.
remote controller holder.
●
To remove, pull it upwards.
ATTENTION
■
About remote controller
Never expose the remote controller to direct sunlight.
•
Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth.
•
Signal communication may be disabled if an electronic-starter-type fluorescent lamp (such as
•
inverter-type lamps) is in the room. Consult the shop if that is the case.
If the remote controller signals happen to operate another appliance, move that appliance to some-
•
where else, or consult the shop.
8
Page 10
■ To set the clock
1. Press “CLOCK button”.
is displayed.
blinks.
2. Press “TIMER setting button”
to set the clock to the present
time.
Holding down “ ” or “ ” button rapidly
increases or decreases the time display.
3. Press “CLOCK button”.
blinks.
■ Turn the breaker ON
Turning ON the breaker opens the flap,
•
then closes it again. (This is a normal procedure.)
NOTE
■
Tips for saving energy
Be careful not to cool (heat) the room too much.
•
Keeping the temperature setting at a moderate level helps save energy.
Cover windows with a blind or a curtain.
•
Blocking sunlight and air from outdoors increases the cooling (heating) effect.
Clogged air filters cause inefficient operation and waste energy. Clean them
•
once in about every two weeks.
■
Please note
The air conditioner always consumes 15-35 watts of electricity even while it is not operating.
•
If you are not going to use the air conditioner for a long period, for example in spring or autumn, turn the breaker OFF.
•
Use the air conditioner in the following conditions.
•
Mode Operating conditions If operation is continued out of this range
COOL
Outdoor temperature:〈2MK(X)S40〉 10 to 46°C
Indoor temperature: 18 to 32°C
Indoor humidity: 80% max.
HEAT
Outdoor temperature:〈2MXS40〉 –10 to 15.5°C
Indoor temperature: 10 to 30°C
DRY
Outdoor temperature:〈2MK(X)S40〉 10 to 46°C
Indoor temperature: 18 to 32°C
• Operation outside this humidity or temperature range may cause a safety device to disable the system.
Indoor humidity: 80% max.
〈2MXS52〉 –10 to 46°C
〈
3/4/5MK(X)S〉 –10 to 46°C
〈RK(X)S〉 –10 to 46°C
〈2MXS52〉 –15 to 15.5°C
〈
3/4/5MXS〉 –15 to 15.5°C
〈
RXS20/25/35〉 –15 to 20°C
〈RXS50/60〉 –15 to 18°C
〈2MXS52〉 –10 to 46°C
〈
3/4/5MK(X)S〉 –10 to 46°C
〈RK(X)S〉 –10 to 46°C
• A safety device may work to stop the operation.
(In multi system, it may work to stop the operation of the outdoor unit only.)
• Condensation may occur on the indoor unit and drip.
• A safety device may work to stop the operation.
• A safety device may work to stop the operation.
• Condensation may occur on the indoor unit and drip.
Recommended temperature setting
For cooling:26°C – 28°C
For heating:20°C – 24°C
2
1, 3
9
Page 11
OPERATION
AUTO · DRY · COOL · HEAT · FAN Operation
The air conditioner operates with the operation mode of your choice.
From the next time on, the air conditioner will operate with the
same operation mode.
■ To start operation
1. Press “MODE selector button”
and select a operation mode.
• Each pressing of the button advances the
mode setting in sequence.
:AUTO
:DRY
: COOL
:HEAT
:FAN
<FDKS>
<FDXS>
2. Press “ON/OFF button” .
• The OPERATION lamp lights up.
4
2, 3
1
5
■ To stop operation
3. Press “ON/OFF button” again.
•
Then OPERATION lamp goes off.
■ To change the temperature setting
4. Press “TEMPERATURE adjustment button”.
DRY or FAN mode AUTO or COOL or HEAT mode
Press “ ” to raise the temperature and press
“ ” to lower the temperature.
The temperature setting is not variable.
10
Set to the temperature you like.
Page 12
■ To change the air flow rate setting
5. Press “FAN setting button”.
DRY mode AUTO or COOL or HEAT or FAN mode
Five levels of air flow rate setting from “ ” to “ ”
The air flow rate setting is not variable.
• Indoor unit quiet operation
When the air flow is set to “ ”, the noise from the indoor unit will become quieter.
Use this when making the noise quieter.
The unit might lose power when the fan strength is set to a weak level.
NOTE
■
Note on HEAT operation
•
Since this air conditioner heats the room by taking heat from outdoor air to indoors, the heating
capacity becomes smaller in lower outdoor temperatures. If the heating effect is insufficient, it is recommended to use another heating appliance in combination with the air conditioner.
•
The heat pump system heats the room by circulating hot air around all parts of the room. After the
start of heating operation, it takes some time before the room gets warmer.
•
In heating operation, frost may occur on the outdoor unit and lower the heating capacity. In that case,
the system switches into defrosting operation to take away the frost.
•
During defrosting operation, hot air does not flow out of indoor unit.
■
Note on DRY operation
• The computer chip works to rid the room of humidity while maintaining the temperature as
much as possible. It automatically controls temperature and fan strength, so manual
adjustment of these functions is unavailable.
■
Note on AUTO operation
•
In AUTO operation, the system selects a temperature setting and an appropriate operation mode
(COOL or HEAT) based on the room temperature at the start of the operation.
•
The system automatically reselects setting at a regular interval to bring the room temperature to usersetting level.
•
If you do not like AUTO operation, you can manually select the operation mode and setting
you like.
■
Note on air flow rate setting
•
At smaller air flow rates, the cooling (heating) effect is also smaller.
plus “ ” “ ” are available.
11
Page 13
POWERFUL Operation
POWERFUL operation quickly maximizes the cooling
(heating) effect in any operation mode. You can get the
maximum capacity .
■ To start POWERFUL
operation
1. Press “POWERFUL button”.
•
POWERFUL operation ends in 20 minutes.
Then the system automatically operates
again with the settings which were used
before POWERFUL operation.
• When using POWERFUL operation,
there are some functions which are not
available.
• “ ” is displayed on the LCD.
■ To cancel POWERFUL
operation
2. Press “POWERFUL button”
again.
• “ ” disappears from the LCD.
1, 2
NOTE
■
Notes on POWERFUL operation
•
In COOL and HEAT mode
To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased
and the air flow rate be fixed to the maximum setting.
The temperature and air flow settings are not variable.
•
In DRY mode
The temperature setting is lowered by 2.5°C and the air flow rate is slightly increased.
•
In FAN mode
The air flow rate is fixed to the maximum setting.
•
When using priority-room setting
See “Note for multi system” (page 18.)
12
Page 14
OUTDOOR UNIT QUIET Operation
OUTDOOR UNIT QUIET operation lowers the noise
level of the outdoor unit by changing the frequency and
fan speed on the outdoor unit. This function is convenient during night.
■ To start OUTDOOR UNIT
QUIET operation
1. Press “QUIET button”.
• “ ” is displayed on the LCD.
■
To cancel OUTDOOR UNIT
QUIET operation
2. Press “QUIET button” again.
• “ ” disappears from the LCD.
1, 2
NOTE
■
Note on OUTDOOR UNIT QUIET operation
• If using a multi system, this function will work only when the OUTDOOR UNIT QUIET operation is set on all operated indoor units.
However, if using priority-room setting, see “Note for multi system” (page 18.)
•
This function is available in COOL, HEAT, and AUTO modes.
(This is not available in FAN and DRY mode.)
• POWERFUL operation and OUTDOOR UNIT QUIET operation cannot be used at the
same time.
Priority is given to POWERFUL operation.
• If operation is stopped using the remote controller or the main unit ON/OFF switch when
using OUTDOOR UNIT QUIET operation, “ ” will remain on the remote controller
display.
13
Page 15
HOME LEAVE Operation
HOME LEAVE operation is a function which allows you to record
your preferred temperature and air flow rate settings.
■ To start HOME LEAVE
operation
1. Press “HOME LEAVE button”.
• “ ” is displayed on the LCD.
• The HOME LEAVE lamp lights up.
■ To cancel HOME LEAVE
operation
2. Press “HOME LEAVE button” again.
• The HOME LEAVE lamp goes off.
• “ ” disappears from the LCD.
1, 2
Before using HOME LEAVE operation.
■
To set the temperature and air flow rate for HOME LEAVE operation
When using HOME LEAVE operation for the first time, please set the temperature and air flow rate
for HOME LEAVE operation.
temperature Air flow rate temperature Air flow rate
Cooling 25
Heating 25°C
1. Press “HOME LEAVE button”. Make sure “ ” is displayed in the remote control
display.
2. Adjust the set temperature with “ ” or “ ” as you like.
3. Adjust the air flow rate with “FAN” setting button as you like.
Home leave operation will run with these settings the next time you use the unit. To change
the recorded information, repeat steps 1 – 3.
14
Record your preferred temperature and air flow rate.
Initial setting Selectable range
°
C
“”
“”
18-32°C
10-30°C
5 step, “ ” and
5 step, “ ” and
“”
“”
Page 16
■ What’s the HOME LEAVE operation?
Is there a set temperature and air flow rate which is most comfortable, a set temperature and air flow
rate which you use the most? HOME LEAVE operation is a function that allows you to record your favorite set temperature and air flow rate. You can start your favorite operation mode simply by pressing the
HOME LEAVE button on the remote control. This function is convenient in the following situations.
■ Useful in these cases
1.Use as an energy-saving mode.
Set the temperature 2-3°C higher (cooling) or lower (heating) than normal. Setting the fan strength to the lowest
setting allows the unit to be used in energy-saving mode. Also convenient for use while you are out or sleeping.
•
Every day before you leave the house...
When you go out, push the “HOME LEAVE
Operation” button, and the air conditioner
will adjust capacity to reach the preset
temperature for HOME LEAVE Operation.
•
Before bed...
Set the unit to HOME LEAVE Operation before leaving the living room
when going to bed.
When you return, you will be welcomed by a comfortably air conditioned room.
The unit will maintain the temperature in the room at a comfortable
level while you sleep.
Push the “HOME LEAVE Operation” button again, and the air conditioner will adjust capacity to the set
temperature for normal operation.
When you enter the living room in the morning, the temperature will be just right.
Disengaging HOME LEAVE Operation will return the temperature to that
set for normal operation. Even the
coldest winters will pose no problem!
2.Use as a favorite mode.
Once you record the temperature and air flow rate settings you most often use, you can retrieve them by
pressing HOME LEAVE button. You do not have to go through troublesome remote control operations.
NOTE
•
Once the temperature and air flow rate for HOME LEAVE operation are set, those settings will be used
whenever HOME LEAVE operation is used in the future. To change these settings, please refer to the
“Before using HOME LEAVE operation” section above.
•
HOME LEAVE operation is only available in COOL and HEAT mode. Cannot be used in AUTO, DRY, and
FAN mode.
•
HOME LEAVE operation runs in accordance with the previous operation mode (COOL or HEAT) before
using HOME LEAVE operation.
•
HOME LEAVE operation and POWERFUL operation cannot be used at the same time.
Last button that was pressed has priority.
•
The operation mode cannot be changed while HOME LEAVE operation is being used.
•
When operation is shut off during HOME LEAVE operation, using the remote controller or the indoor unit
ON/OFF switch, “ ” will remain on the remote controller display.
15
Page 17
TIMER Operation
Timer functions are useful for automatically switching the
air conditioner on or off at night or in the morning. You can
also use OFF TIMER and ON TIMER in combination.
■
To use OFF TIMER operation
• Check that the clock is correct.
If not, set the clock to the present time.
(page 9.)
1. Press “OFF TIMER button”.
is displayed.
blinks.
2. Press “TIMER Setting button”
until the time setting reaches the
point you like.
• Every pressing of either button increases
or decreases the time setting by 10 minutes. Holding down either button changes
the setting rapidly.
3. Press “OFF TIMER button”
again.
• The TIMER lamp lights up.
2
4
1, 3
■ To cancel the OFF TIMER operation
4. Press “CANCEL button”.
•
The TIMER lamp goes off.
NOTE
•
When TIMER is set, the present time is not displayed.
•
Once you set ON, OFF TIMER, the time setting is kept in the memory. (The memory is canceled when
remote controller batteries are replaced.)
•
When operating the unit via the ON/OFF Timer, the actual length of operation may vary from the time
entered by the user. (Maximum approx. 10 minutes)
■
NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically adjusts the temperature setting (0.5°C
up in COOL, 2.0°C down in HEAT) to prevent excessive cooling (heating) for your pleasant sleep.
16
Page 18
■ To use ON TIMER operation
• Check that the clock is correct. If not, set
the clock to the present time
(page 9.).
1. Press “ON TIMER button”.
is displayed.
blinks.
2. Press “TIMER Setting button”
until the time setting reaches
the point you like.
• Every pressing of either button
increases or decreases the time setting
by 10 minutes. Holding down either button changes the setting rapidly.
3. Press “ON TIMER button”
again.
•
The TIMER lamp lights up.
1, 3
4
2
■ To cancel ON TIMER operation
4. Press “CANCEL button”.
•
The TIMER lamp goes off.
■ To combine ON TIMER and OFF TIMER
• A sample setting for combining the two timers is shown below.
(Example)
Present time: 11:00 p.m.
(The unit operating)
OFF TIMER at 0:00 a.m.
ON TIMER at 7:00 a.m.
ATTENTION
■
In the following cases, set the timer again.
•
After a breaker has turned OFF.
•
After a power failure.
•
After replacing batteries in the remote controller.
Combined
Display
17
Page 19
Note for Multi System
〈〈
What is a “Multi System”?
This system has one outdoor unit connected to multiple indoor units.
■
Selecting the Operation Mode
1. With the Priority Room Setting
present but inactive or not present.
When more than one indoor unit is operating, priority is
given to the first unit that was turned on.
In this case, set the units that are turned on later to the
same operation mode (*1) as the first unit.
Otherwise, they will enter the Standby Mode, and the operation lamp will flash; this does not indicate malfunction.
(*1)
• COOL, DRY and FAN mode may be used at the same time.
• AUTO mode automatically selects COOL mode or HEAT mode based on the room temperature.
Therefore, AUTO mode is available when selecting the same operation mode as that of the room
with the first unit to be turned on.
〈
CAUTION
Normally, the operation mode in the room where the unit is first run is given priority, but the following situations are
exceptions, so please keep this in mind.
If the operation mode of the first room is FAN Mode, then using Heating Mode in any room after this will give priority to
heating. In this situation, the air conditioner running in FAN Mode will go on standby, and the operation lamp will flash.
〉
〉〉
A
C
room
room
B
room
Outdoor
unit
Living
room
2. With the Priority Room Setting active.
See “Priority Room Setting” on the next page.
■
NIGHT QUIET Mode (Available only for cooling operation)
NIGHT QUIET Mode requires initial programming during installation. Please consult your retailer or dealer for assistance.
NIGHT QUIET Mode reduces the operation noise of the outdoor unit during the night time hours to prevent
annoyance to neighbors.
•
The NIGHT QUIET Mode is activated when the temperature drops 5°C or more below the highest temperature
recorded that day. Therefore, when the temperature difference is less than 5°C, this function will not be activated.
•
NIGHT QUIET Mode reduces slightly the cooling efficiency of the unit.
■
OUTDOOR UNIT QUIET Operation
(page 13.)
1. With the Priority Room Setting present but inactive or not present.
When using the OUTDOOR UNIT QUIET operation feature with the Multi system, set all indoor units to
OUTDOOR UNIT QUIET operation using their remote controllers.
When clearing OUTDOOR UNIT QUIET operation, clear one of the operating indoor units using their remote controller.
However OUTDOOR UNIT QUIET operation display remains on the remote controller for other rooms.
We recommend you release all rooms using their remote controllers.
2. With the Priority Room Setting active.
See “Priority Room Setting” on the next page.
■
Cooling / Heating Mode Lock (Available only for heat pump models)
The Cooling / Heating Mode Lock requires initial programming during installation.Please consult your retailer or dealer
for assistance. The Cooling / Heating Mode Lock sets the unit forcibly to either Cooling or Heating Mode. This function
is convenient when you wish to set all indoor units connected to the Multi system to the same operation mode.
18
Page 20
■ Priority Room Setting
The Priority Room Setting requires initial programming during installation. Please consult your
retailer or dealer for assistance.
The room designated as the Priority Room takes priority in the following situations;
1. Operation Mode Priority.
As the operation mode of the Priority Room takes precedence, the user can select a different
operation mode from other rooms.
〈
2. Priority when POWERFUL operation is used.
〈Example
3. Priority when using OUTDOOR UNIT QUIET operation.
〈Example〉
〉
Example
* Room A is the Priority Room in the examples.
When COOL mode is selected in Room A while operating the following modes in Room B,C and D :
Operation mode in Room B, C and D Status of Room B, C and D when the unit in Room A is in COOL mode
COOL or DRY or FAN Current operation mode maintained
HEAT
AUTO
〉
* Room A is the Priority Room in the examples.
The indoor units in Rooms A,B,C and D are all operating. If the unit in Room A enters POWERFUL
operation, operation capacity will be concentrated in Room A. In such a case, the cooling (heating)
efficiency of the units in Rooms B,C and D may be slightly reduced.
* Room A is the Priority Room in the examples.
Just by setting the unit in Room A to QUIET operation, the air conditioner starts OUTDOOR UNIT
QUIET operation.
You don’t have to set all the operated indoor units to QUIET operation.
The unit enters Standby Mode. Operation resumes when the
Room A unit stops operating.
If the unit is set to COOL mode, operation continues. If set to
HEAT mode, it enters Standby Mode. Operation resumes when
the Room A unit stops operating.
19
Page 21
CARE
Care and Cleaning
CAUTION
• Only a qualified service person is allowed to
perform maintenance.
• Before cleaning, be sure to stop the operation
and turn the breaker OFF.
■ Cleaning the air filter
1.Removing the air filter.
• Rear suction
Pull the bottom side of the air filter backwards, over the bends. (2 bends for 25/35 type, 3 bends
for 50/60 type)
• Bottom suction
Pull the filter over the bends (2 bends for 25/35 type, 3 bends for 50/60 type) situated at the
backside of the unit.
2.Cleaning the air filter.
Remove dust from the air filter using a vacuum cleaner and
gently rinse them in cool water. Do not use detergent or hot
water to avoid filter shrinking or deformation. After cleaning
dry them in the shade.
3.Replacing the air filter.
• Rear suction
Hook the filter behind the flap situated at the top of the unit
and push the other side gently over the bends. (2 bends for 25/35 type, 3 bends for 50/60 type)
• Bottom suction
Hook the filter behind the flap situated at the middle of the unit and push the other side gently
over the bends. (2 bends for 25/35 type, 3 bends for 50/60 type)
Main unit
Filter
Force
Attach the filter to the
main unit while
Force
pushing down on the
bends. (2 bends for
25/35 type, 3 bends
for 50/60 type)
20
In case of back side
In case of bottom side
Page 22
■ Cleaning the drain pan
•
Clean the drain pan periodically, or drain piping may be clogged with dust and may result in water leakage.
Ask your DAIKIN dealer to clean them.
•
Prepare a cover locally to prevent any dust in the air around the indoor unit from getting in the drain pan, if
there is a great deal of dust present.
CAUTION
• Do not operate the air conditioner without filters, this to avoid dust accumulation inside the
unit.
• Do not remove the air filter except when cleaning.
Unnecessary handling may damage the filter.
•
Do not use gasoline, benzene, thinner, polishing powder, liquid insecticide, It may cause discoloring or
warping.
•
Do not let the indoor unit get wet. It may cause an electric shock or a fire.
• Operation with dusty air filters lowers the cooling and heating capacity and wastes energy.
• The suction grille is option.
• Do not use water or air of 50°C or higher for cleaning air filters and outside panels.
• Ask your DAIKIN dealer how to clean it.
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
•
If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult the service shop if this is the case.
■ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE selector button” and select “FAN” operation.
• Press “ON/OFF button” and start operation.
2. Clean the air filters and set them again.
3. Take out batteries from the remote controller.
4. Turn OFF the breaker for the room air conditioner.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
TROUBLE SHOOTING
other room before you use the fan operation. (page 18.)
21
Page 23
Trouble Shooting
These cases are not troubles.
The following cases are not air conditioner troubles but have some reasons. You may just continue using it.
Case Explanation
Operation does not start soon.
• When ON/OFF button was
pressed soon after
operation was stopped.
• When the mode was
reselected.
Hot air does not flow out soon
after the start of heating
operation.
The heating operation stops
suddenly and a flowing sound
is heard.
The outdoor unit emits water or
steam.
Mists come out of the indoor
unit.
The indoor unit gives out odour.
The outdoor fan rotates while
the air conditioner is not in
operation.
The operation stopped
suddenly.
(OPERATION lamp is on.)
• This is to protect the air conditioner.
You should wait for about 3 minutes.
• The air conditioner is warming up. You should wait for 1 to 4
minutes.
(The system is designed to start discharging air only after it
has reached a certain temperature.)
• The system is taking away the frost on the outdoor unit.
You should wait for about 3 to 8 minutes.
■ In HEAT mode
• The frost on the outdoor unit melts into water or steam
when the air conditioner is in defrost operation.
■ In COOL or DRY mode
• Moisture in the air condenses into water on the cool
surface of outdoor unit piping and drips.
■ This happens when the air in the room is cooled into mist by
the cold air flow during cooling operation.
■ This happens when smells of the room, furniture, or
cigarettes are absorbed into the unit and discharged with the
air flow.
(If this happens, we recommend you to have the indoor unit
washed by a technician. Consult the service shop where you
bought the air conditioner.)
■ After operation is stopped:
• The outdoor fan continues rotating for another 30
seconds for system protection.
■ While the air conditioner is not in operation:
• When the outdoor temperature is very high, the outdoor
fan starts rotating for system protection.
■ For system protection, the air conditioner may stop
operating on a sudden large voltage fluctuation.
It automatically resumes operation in about 3 minutes.
22
Page 24
Check again.
Please check again before calling a repair person.
Case Check
The air conditioner does not
operate.
(OPERATION lamp is off.)
Cooling (Heating) effect is poor.
Operation stops suddenly.
(OPERATION lamp blinks.)
An abnormal functioning
happens during operation.
• Hasn’t a breaker turned OFF or a fuse blown?
• Isn’t it a power failure?
• Are batteries set in the remote controller?
• Is the timer setting correct?
• Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
• Is the temperature setting appropriate?
• Are the windows and doors closed?
• Are the air flow rate and the air direction set appropriately?
• Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
Clean the air filters or take all obstacles away and turn the
breaker OFF. Then turn it ON again and try operating the air
conditioner with the remote controller. If the lamp still blinks,
call the service shop where you bought the air conditioner.
• Are operation modes all the same for indoor units
connected to outdoor units in the
If not, set all indoor units to the same operation mode and
confirm that the lamps blink.
Moreover, when the operation mode is in “AUTO”, set all
indoor unit operation modes to “COOL” or “HEAT” for a
moment and check again that the lamps are normal.
If the lamps stop blinking after the above steps, there is no
malfunction.
(page 18.)
• The air conditioner may malfunction with lightning or radio
waves. Turn the breaker OFF, turn it ON again and try
operating the air conditioner with the remote controller.
multi system
?
23
Page 25
Call the service shop immediately.
WARNING
■
When an abnormality (such as a burning smell) occurs, stop operation and turn the breaker OFF.
Continued operation in an abnormal condition may result in troubles, electric shocks or fire.
Consult the service shop where you bought the air conditioner.
■ Do not attempt to repair or modify the air conditioner by yourself.
Incorrect work may result in electric shocks or fire.
Consult the service shop where you bought the air conditioner.
If one of the following symptoms takes place, call the service shop immediately.
n
n
n
n
n
n
Turn the breaker
OFF and call the
service shop.
■ After a power failure
The air conditioner automatically resumes operation
in about 3 minutes. You should just wait for a while.
■ Lightning
If lightning may strike the neighbouring area, stop operation and turn the breaker OFF for system protection.
Disposal requirements
Your air conditioning product is marked with this symbol. This means that electrical and
electronic products shall not be mixed with unsorted household waste.
Do not try to dismantle the system yourself: the dismantling of the air conditioning
system, treatment of the refrigerant, of oil and of other parts must be done by a
qualified installer in accordance with relevant local and national legislation.
Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By
ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for
the environment and human health. Please contact the installer or local authority for more information.
Batteries must be removed from the remote controller and disposed of separately in accordance with
relevant local and national legislation.
We recommend periodical maintenance.
In certain operating conditions, the inside of the air conditioner may get foul after several seasons of use, resulting in poor performance. It is recommended to have periodical maintenance by a specialist aside from regular
cleaning by the user. For specialist maintenance, contact the service shop where you bought the air conditioner.
The maintenance cost must be born by the user.
Important information regarding the refrigerant used.
This product contains fluorinated greenhouse gases covered by the Kyoto Protocol.
Refrigerant type:
(1)
GWP
value:
(1)
GWP = global warming potential
Periodical inspections for refrigerant leaks may be required depending on European or local legislation.
Please contact your local dealer for more information.
R410A
1975
24
Page 26
Fault diagnosis.
FAULT DIAGNOSIS BY REMOTE CONTROLLER
In the ARC433 series, the temperature display sections on the main unit indicate corresponding codes.
1. When the TIMER CANCEL button is held down for 5 seconds, a
indication flashes on the
“”
temperature display section.
TIMER CANCEL button
It cancels the timer setting.
2. Press the TIMER CANCEL button repeatedly until a continuous beep is produced.
• The code indication changes in the sequence shown below, and notifies with along beep.
CODE MEANING
00 NORMAL
SYSTEM
INDOOR UNIT
OUTDOOR
UNIT
U0 REFRIGERANT SHORTAGE
U2 DROP VOLTAGE OR MAIN CIRCUIT OVERVOLTAGE
U4 FAILURE OF TRANSMISSION (BETWEEN INDOOR UNIT AND OUTDOOR UNIT)
A1 INDOOR PCB DEFECTIVENESS
A5 HIGH PRESSURE CONTROL OR FREEZE-UP PROTECTOR
A6 FAN MOTOR FAULT
C4 FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
C9 FAULTY SUCTION AIR TEMPERATURE SENSOR
EA COOLING-HEATING SWITCHING ERROR
E5 OL STARTED
E6 FAULTY COMPRESSOR START UP
E7 DC FAN MOTOR FAULT
E8 OPERATION HALT DUE TO DETECTION OF INPUT OVER CURRENT
F3 HIGH TEMPERATURE DISCHARGE PIPE CONTROL
F6 HIGH PRESSURE CONTROL (IN COOLING)
H6 OPERATION HALT DUE TO FAULTY POSITION DETECTION SENSOR
H8 CT ABNORMALITY
H9 FAULTY SUCTION AIR TEMPERATURE SENSOR
J3 FAULTY DISCHARGE PIPE TEMPERATURE SENSOR
J6 FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
L4 HIGH TEMPERATURE AT INVERTER CIRCUIT HEATSINK
L5 OUTPUT OVERCURRENT
P4 FAULTY INVERTER CIRCUIT HEATSINK TEMPERATURE SENSOR
NOTE
1. A short beep and two consecutive beeps indicate non-corresponding codes.
2. To cancel the code display, hold the TIMER CANCEL button down for 5 seconds. The code display
also cancel itself if the button is not pressed for 1 minute.
25
Page 27
LED ON OUTDOOR UNIT PCB 2MXS, 3MXS, 3MKS, 4MXS, 4MKS, 5MXS, 5MKS series
GREEN
MICROCOMPUTER
NORMAL
LED1 LED2 LED3 LED4LED-A LED5
RED
MALFUNCTION
DETECTION
NORMAL CHECK INDOOR UNIT
HIGH PRESSURE PROTECTOR WORKED OR FREEZE-UP IN OPERATING UNIT OR STAND-BY UNIT
∗
OVERLOAD RELAY WORKED OR HIGH DISCHARGE PIPE TEMPERATURE
FAULTY COMPRESSOR START
INPUT OVERCURRENT
∗ THERMISTOR OR CT ABNORMALITY
HIGH TEMPERATURE SWITCHBOX
HIGH TEMPERATURE AT INVERTER CIRCUIT HEATSINK
∗ OUTPUT OVERCURRENT
∗ REFRIGERANT SHORTAGE
LOW VOLTAGE TO MAIN CIRCUIT OR MOMENTARY VOLTAGE LOSS
REVERSING SOLENOID VALVE SWITCHING FAILURE
FAN MOTOR FAULT
[NOTE 1]
POWER SUPPLY FAULT OR [NOTE 2]
NOTE: The LED5 is only available in the 5M Series.
GREEN
RED
NORMALLY
FLASHING
NORMALLY OFF
ON
FLASHING
OFF
IRRELEVANT
LED ON OUTDOOR UNIT PCB 2MXS, 2MKS series
GREEN
MICROCOMPUTER
NORMAL
LED-A
NORMAL CHECK INDOOR UNIT
[NOTE 1]
POWER SUPPLY FAULT OR [NOTE 2]
DIAGNOSIS
DIAGNOSIS
NORMALLY
GREEN
FLASHING
ON
FLASHING
OFF
NOTE
1. Turn the power off and then on again. If the LED display recurs,the outdoor unit PCB is faulty.
2. Diagnosis marked
∗
Do not apply to some cases. For details, refer to the service guide.
26
Page 28
3P196326-9B
Two-dimensional bar code is a code
for manufacturing.
EM06A065B
(0704)
HT
Loading...