EKHBHE008AA3V3
EKHBXE008AA3V3
Indoor unit for air to water heat pump
system and options
Addendum
Operation manual
For installation WITH restricted power supply condition
Programming space cooling or space heating
aa
aa
The following information is valid when installing the optional
domestic hot water tank.
Simultaneous operation of compressor, backup heater and booster
heater is NOT possible. Refer to the following warnings mentioned in
the operation manual:
- Emergency backup heater operation always has priority over
compressor or booster heater operation.
- Balance between space heating/cooling demand and
domestic hot water demand.
To optimize the comfort balance between space heating/cooling and
domestic hot water, the schedule timers must be used.
The following shows step-by-step a possible space heating/cooling
and domestic hot water pattern. To ensure domestic hot water
production, the schedule timers must be used to disable space
heating/cooling. When space heating/cooling is disabled the
heatpump will switch automatically to domestic water heating. In this
case it is not required to program the domestic hot water or booster
heater schedule timer.
Example pattern
Time
Space
heating/cooling
0000::::000000001111::::000000002222::::000000003333::::000000004444::::000000005555::::000000006666::::000000007777::::00000000~
22223333::::555599
99
=6 kW
In this example, the domestic hot water tank will be heated between
2:00
and
4:00
.
If using a room thermostat, domestic water heating by
compressor or by booster heater is
as the room thermostat demands cooling or heating.
In this case de-activate the room thermostat demand by its
schedule timer.
Refer to the manual of the room thermostat for a detailed
explanation how to de-activate space heating/cooling by
schedule timer, or refer to the separate addendum for an
example of the Daikin room thermostat schedule timer
programming.
NOT
possible as long
5 sec
Addendum
1
5 sec
Indoor unit for air to water heat pump system and options
EKHBH/XE008AA3V3
4PW50001-1A
Programming space cooling or space heating is carried out as
follows:
Refer to the operation manual on how to program the schedule
timers.
NOTE
Returning to previous steps in the programming
procedure without saving modified settings is done by
pressing the pr button.
1
Use the = button to select the heating/cooling operation
mode.
2
Press the < button.
The actual mode is blinking.
3
Press the < button to confirm the selected mode.
The actual day is blinking.
4
Use the
pi
and
pj
buttons until "1" (monday) is
blinking.
5
Press the < button to confirm the selected day.
The first programmed action of the selected day appears.
6
Press the < button for 5 seconds to enter the programming
mode.
7
Use the < button to select the action number 1.
8
Use the
pi
and
pj
buttons to set the correct action time
to
2:00
.
9
Use the ba button to select x as action.
10
Use the < button to select action number 2.
11
Use the
pi
and
pj
buttons to set the action time to
12
Use the ba buttons to select what the unit should do from
4:00
4:00
onwards.
-
9
: set the tempearature by means of the
bj
buttons.
bi
and
-a: to select automatic temperature calculation (only in
heating mode)
13
Press the < button for 5 seconds to store the programmed
actions.
You automatically return to step 4.
By pressing the pr button several times, you return to previous
steps in the procedure and finally return to normal operation.
14
Repeat this sequence for all the days of the week.
Now, the unit is programmed to stop space heating/cooling between
2:00
and
4:00
. The unit will start space heating/cooling from
4:00
this is programmed (see step 12).
NOTE
Other actions can also be programmed for times
during the day. See operation manual on how to
program other actions.
NOTE
■
When booster heater and domestic hot water
schedule timers are used, make sure they are
enabled during the period that space
heating/cooling is disabled.
Example pattern:
7777::::00000000~
00
22223333::::555599
99
Space
heating/cooling
Domestic water
heating
Booster heating
■
0000::::000000001111::::000000002222::::000000003333::::000000004444::::000000005555::::000000006666::::000000
In case the disinfection function is required, the
schedule timer for domestic water heating and
booster heating must be used. If the domestic
water heating and booster heater are not stopped,
than this disinfection can not start.
Disinfection example pattern (refer to paragraph
"[2] Disinfection function" in the operation
manual).
Mon
Tue Wed Thu Fri Sat Sun
.
Pattern 1
Pattern 2 — — —
Pattern 1
Space
heating/cooling
Domestic water
heating
Booster heating
Pattern 2
if
Space
heating/cooling
Domestic water
heating
Booster heating
✓✓✓
0000::::000000001111::::000000002222::::000000003333::::000000004444::::000000005555::::000000006666::::000000
0000::::000000001111::::000000002222::::000000003333::::000000004444::::000000005555::::000000006666::::000000
—
✓✓✓
———
✓
7777::::00000000~
00
99
22223333::::555599
7777::::00000000~
00
99
22223333::::555599
EKHBH/XE008AA3V3
Indoor unit for air to water heat pump system and options
4PW50001-1A
Disinfection
function
Addendum
2