- If the vacuum bag isn’t full and the full bag indicator is red, check
the hose for a clog.
• When cleaning with a tool (dusting brush,upholstery tool,crevice
tool,floor tool), the red indicator may appear. In this case, continue
cleaning.
HOSE ADAPTER
• When separating the hose from the body, pull the
hose adapter while pressing the buttons.
Adapter button
ON/OFF SWITCH
POWER CONTROLHOSE HANDLE
HARD SURFACE FLOOR TOOL
• For use on tile, hard wood, and
linoleum floors.
Petite Power
Nozzle
•3n1 multi-purpose tool
Insert end of wand into either end of
tool for multiple cleaning functions.
Upholstery Tool
CLEANING TOOLS
Crevice ToolDusting Brush
STORAGE
• Insert the brush holder
on the neck of the wand
into the groove.
54
Wand Extension Grip (to extend wand)
Handle
Telescopic Wand
Power Nozzle
Handle
Telescopic Wand
Power Nozzle
On/Off Control
Wand Release Button
Wand Extension Grip
(to extend wand)
Nozzle Release Button
S20-Simplicity-1214 2004.12.14 11:55 AM 7
HOW TO USE POWER NOZZLE
OPERATION
1. Turning on the Power Nozzle
The power nozzle can only be turned on if the
canister is also turned on (canister on / off
switch is located on the main body). The
power nozzle on / off switch is located on the
handle. Simply press the switch forward to
engage the power nozzle.
2. Using the Power Nozzle
To achieve best cleaning results, slowly pass
the power nozzle back and forth over the
carpet or floor.
DIAGRAM 1 REAR VIEW OF POWER WAND AND NOZZLE ASSEMBLY
3. Remove / Insert the Wand From The Power
Nozzle
Removing the wand from the power nozzle
allows you to use the cleaning tools for
baseboard or ceiling cleaning. To do this first
turn the power nozzle and canister off. Then,
press the nozzle release button and pull the
wand out. To reinsert the wand into the power
nozzle, simply press the back into the neck of
the power nozzle. The wand will then “click”
back into place.
DIAGRAM 2 FRONT VIEW OF POWER WAND AND NOZZLE ASSEMBLY
76
S20-Simplicity-1214 2004.12.14 11:55 AM 9
SAFETY PRECAUTIONSREPLACING VACUUM BAG & FILTERS
This vacuum cleaner should be used for normal, dry household dust and dirt.
The manufacturer cannot be held responsible for any damage caused by use or operation of the vacuum
contrary to these instructions.
If the vacuum is wrongly operated for a purpose other than that for which it is intended, no liability can be
accepted for any possible damage.
• Do not vacuum areas which contain moisture
or water, flammable matter, needles, pins, razor
blades, matches, cigarettes, etc., since they
may damage the vacuum or vacuum bag.
• Make sure a vacuum bag and filters are always
inserted.
• When rewinding the power cord, hold the plug
before pressing the cord rewind button to
prevent the cord from whipping.
• This product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other). This plug fits into
the power outlet only one way.
This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact
an electrician to replace the obsolete outlet.
Do not defeat the safety purpose of the
polarized plug.
REPLACING THE VACUUM BAG
Full Bag
Indicator
Dust Cover
• Turn canister off, remove
hose and open the dust cover.
NOTE: We recommend the vacuum bag is changed when indicator is RED or suction power is weak.
The dust cover will not close without a bag in the unit or if the bag is not properly inserted.
Vacuum Bag
Holder
• Pull the shutter of the vacuum bag.
• Hold the cover while removing
the vacuum bag from the
vacuum bag holder.
• Insert the new bag.
REPLACING THE FILTERS
Charcoal Filter
• Switch off and open the cover.
• Remove filter.
• Shake the dust out of the filter.
• Insert the filter and close the cover.
HEPA Filter
Charcoal Filter
HEPA Filter
• Switch off and open the grill.• Remove the filter, replace it and close the grill.
98
S20-Simplicity-1214 2004.12.14 11:55 AM 11
TROUBLESHOOTING GUIDE
■ Please check each item below if you have trouble with your vacuum.
Before checking, ensure that the vacuum is unplugged from the power supply.
Problem
• Suction power is weak.
• The vacuum does not work.
• Power cord does not rewind.
• Vacuum bag
• Wand or hose
• Is the hose adapter inserted
• When the vacuum bag is full
• Power cord
Check Point
into the suction opening of the
vacuum completely?
or any of the accessories are
blocked, the over-heating
protection for the motor is
activated.
• If vacuum bag is full, replace
it.
• If clogged or blocked, remove
the object.
• Insert it completely.
• Switch off and unplug the
vacuum. Check the vacuum
bag and accessories and
remove any blockages. The
vacuum can be switched on
again after approximately 20
minutes.
• Pull the power cord out a little
and press the cord rewind
button again.
NOTES
Possible Solution
• Power cord won't pull out of
the vacuum.
• Power cord
• Do not pull it by force. Rewind
SPECIFICATIONS
Model
Rating
Amps
Weight
Dimension (L X W X H)
Cord Length
• Specifications can be changed for improvement without notice.
For assistance please visit www.Simplicityvac.com or call 1-888-9Simply.
10
120V/60Hz
15.5 Pounds
19" x 12.5" x 9.3"
18 feet
it a little by pressing the cord
rewind button and try pulling it
out again.
S20
9.5A
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.