Daewoo KOR-86250S, KOR-63250S Service Manual

S/M No. : R63250S001

Service Manual

Microwave Oven

Model: KOR-63250S KOR-86250S

DAEWOO ELECTRONICS CO., LTD.

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSI VE MICR OWAV E ENERGY

(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave

source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5) Evidence of dropping or abuse.

generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.

(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and

transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.

(e) A microwave leakage check to verify compliance with the Federal performance standard should be performed on

each oven prior to release to the owner.

  

SAFETY AND PRECAUTIONS ........................................................................................................ 2

1. FOR SAFE OPERATION ............................................................................................................. 2

2. FOR SAFE SERVICE PROCEDURES ........................................................................................ 2

SPECIFIC ATIONS ... ............ ......... ............ ............ ......... ............ ......... ........... ............ ......... .............. 3

EXTERNAL VIEW ............................................................................................................................ 4

1. OUTER DIMENSION .................................................................................................................... 4

2. FEATURE DIAGRAM ................................................................................................................... 4

INSTALLATIO N . ...... ...... ... ...... ... ...... ...... ... ...... ...... ... ...... ... ...... ...... ... ..... ...... ... ...... ...... ... ...... .............. 5

OPERATIONS AND FUNCTIONS .............................................................................. ......... ......... ... 6

DISASSEMBLY AND ASSEMBLY ......................................................................................... ......... 7

INTERLOCK MECHANISM AND ADJUSTMENT ........................................................................... 14

TROUBLE SHOOTING GUIDE ........................................................................................................ 15

MEASUREMENT AND TEST ...................................................................................... ......... ......... ... 1 7

1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ..................................................... 17

2. MICROWAVE RADIATION TEST ................................................................................................ 18

3. COMPONENT TEST PROCEDURE ............................................................................................ 19

WIRING DIAGRAM .......................................................................................................................... 20

EXPLODED VIEW AND PARTS LIST ............................................................................................. 21

1. DOOR ASSEMBLY ...................................................................................................................... 21

2. CONTROL PANEL ASSEMBLY.................................................................................................... 21

3. TOTAL ASSEMBLY ...................................................................................................................... 21



SAFETY AND PREC AUTIONS

1. FOR SAFE OPERATION

Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE. (Only a trained service personnel should make repairs.)

1) A broken door hinge.

2) A broken door viewing screen.

3) A broken front panel, oven cavity.

4) A loosened door lock.

5) A broken door lock. The door gasket plate and oven cavity surface should be kept clean. No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven. DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN. The microwave oven has concealed switches to make sure the power is turned off when the door is opened. Do not attem p t to defeat them. DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.

2. FOR SAFE SERVICE PROCEDURES

1. If th e ove n is operative prior to servicin g, a microwav e emission check s ho uld b e p erforme d p rior to servicing the oven.

2. If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the oven.

(a) inform the manufacturer, importer or assembler, (b) repair the unit at no cost to the owner, (c) attempt to ascertain the cause of the excessive leakage, (d) tell the owner of the unit not to use the unit until the oven has been brought into compliance.

3. If the oven operates with the door open, the service person should tell the user not to operate the oven and contact the

manufacturer immediately.

IMPORTANT

The wire in this mains lead coloured in accordance with the following code. Green-and-yellow : Earth

Blue : Neutral Brown : Live

As the colours of the wires in the m anins lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire w hich is coloured green-and-yellow must be connected to the term ianl in the plug which is marked with the letter ‘E’ or by earth sym bol or green-and-yellow. The wire w hich is coloured blue m ust be connected to the terminal which is m arked with the letter ‘N’ or coloured black. The wire w hich is coloured brown m ust be connected to the terminal which is m arked with the letter ‘L’ or coloured red.

NOTE

This oven is designed for counter-top use only.



SPECIFICATIONS

KOR-6325

MODEL KOR-6325 POW E R SU P PLY 230V-50Hz, SINGLE PH ASE W ITH EARTHIN G

MICROWAVE 1200W

POWER CONS UMPTION

MICROW AVE ENERGY OUT PUT 800W MICROW AVE FREQUE NCY 2450MHz OUTSIDE DIME N SION S (W X H X D ) 465 x 279 x 360 mm (18.3 x 11.0 x 14.2 in.) CAVITY DIMENSIONS (W X H X D ) 290 x 220 x 306 mm (11.4 x 8.7 x 12.0 in.) NET WEIGHT APPROX. 13 Kg ( 28.7 lbs.) TIMER 35 min. DUAL SPEED FUNCTIO N SELECTIONS MICROWAVE POWE R SELECTIONS 5 LEVELS CAVITY VOLUME 0.7 Cu.Ft.

GRILL COMBINATION

KOR-8625

MODEL POWER SUPPLY

MICROWAVE

POWER CONS UMPTION

MICROWAVE EN ERGY OUTPUT MICROWAVE FREQUENCY OUTSIDE DIMENSIONS (W X H X D) CAVITY DIMENSIONS (W X H X D) NET WEIGHT TIMER FUNCTIO N SELECTIONS POWE R SELECTIONS CAVITY VOLUME



Specifications are subject to change without notice.

GRILL COMBINATION

KOR-8625

230V-50Hz, SINGLE PHASE WITH EARTH ING

1350W

900W

2450MHz

495 x 294 x 388 m m (19.5 x 11.6 x 15.3 in.)

320 x 244 x 338 m m (12.6 x 9.6 x 13.3 in.)

APPRO X . 15 Kg ( 33.1 lbs.)

35 min. DU AL SPEED

MICROWAVE

5 LEVELS

0.9 C u.Ft.



EXTERNAL VIEW

1. OUTER DIMENSION

- KOR-6325/KOR- 8625

465/495 360/388

Fig.1 Front view

2. FEATURE DIAGRAM

1. Safety interlock system

2. Door viewing screen -

3. Door hook -

the autom atically shut off.

4. Oven cavity

5. Door seal -

6. Glass cooking tray -

7. Roller guide -

8. Coupler -

9. Knob V.P.C -

10. Knob timer -

When the door is closed, it will automatically shut off. If the door is opened while the oven is operating,

Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage.

This must always be used for cooking together with the glass cooking tray.

This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking.

Used to select a microwave power level.

Used in setting cooking time for all functions.

Allows viewing of food. The screen is designed so that light can pass through, but not the microwave.

Made of special heat resistant glass. Food in a proper receptacle is placed on this tray for cooking.

Fig.2 Side view



INSTALLATION

1. Steady, flat location

This microwave oven should be set on a steady, flat surface. This microwave oven is designed for counter top use only.

2. Leave space behind and side

All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually, cause failure.

3. Away from radio and TV sets

Poor television reception and radio interference ma y result if the oven is located close to a TV, radio, antenna or feeder and so on.

Position the oven as far from them as possible.

4. Away from heating appliances and water taps

Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be adversely affected and breakdowns occur.

5. Power supply

• Check your local power source.

This microwave oven requires a current of approximately 6amperes, 230 Volts, 50 Hz.

• Power supply cord is about 0.8 meters long.

• The voltage used must be the same as specified on this oven. Using a higher voltage m ay result in a fire or other accident

causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage resulting from use of this oven with a voltage of ampere fuse other than those specified.

• This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same type.

Such a cable can be purchased from DAEWOO and must be installed by a Qualified Person.

6. Examine the oven after unpacking for any damage such as:

A misaligned door, broken door or a dent in cavity. If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.

7. Do not operate the oven if it is colder than room temperature

(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.

EARTHING INSTRUCTIONS

This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric shock by providing an esca pe wire for the electric current. This appliance is equipped w ith a c ord h aving a e arthing w ire with a earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.

WARNING

Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified electrician or serviceman if the earthing instructions are not completely understood, or if doubt exists as to whether the appliance is properly earthed, and either : If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade earthing plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord should be equal to or greater than the electrical rating of the appliance, or Do not use an extension cord.



OPERATIONS AND FUNCTIONS

1. Connect the main lead to an electrical outlet.

2. After placing the food in a suitable container, open the oven

door and put it on the glass tray. The glass tray must always be in place during cooking.

3. Close the door securely.

4. Choose cooking power level by setting V.P.C knob to the

desired position. Refer to cookbook for recommended power levels.

5. Determine cooking time.

Consult cookbook for recipe timing. Oven light turns on and cooling fan starts to operate. Microwave cooking starts.

6. You may open the door while the oven is operating.

As soon as the door is opened, the safety mechanims stop the generation of microwave power and the operation of cooking timer. If you wish to change the time during cooking, simply adjust the timer to the desired time.

7. When the timer reaches zero, a bell will ring and the unit will turn off.

Oven light turns off. If additional cooking time is needed and the door is closed, the oven will automatically start when the timer is reset.

NOTE

1. When setting timer for less than 2 minutes, turn the timer past 2 minutes and then return to the correct timer setting.

2. Various clicking noises may be heard when turning V.P.C knob. This is normal and does not affect the operation of your microwave oven.

Make sure the oven is properly installed and plugged into the electrical outlet.

Variable power cooking

On and OFF cycle time of mechanical V.P.C switch is 30 seconds. When the V.P.C knob is set to the desired position and timer knob turns to the desired position, the V.P.C switch has a cycle (ON/OFF time(sec.)) listed below.



6325/8625

Variab le powe r setting ON/OFF time (sec.) Approximate Percentage of Power

MAX (HIGH) 30/0 100 %

610W / 700W (MED HIGH) 23.2/6.8 77 %

440W / 500W (MEDIUM) 16.5/13.5 55 %

260W / 290W (DEFROST) 9.8/20.2 33 %

130W / 150W (WARM ) 5/25 17 %



DISASSEMBLY AND ASSEM BLY

Cautions to be observed when trouble shooting

Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safety during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit. You are asked to observe the following precautions carefully.

1. Always remove the power plug from the outlet before servicing.

2. Use an insulated screwdriver and ware rubber gloves when servicing the high voltage side.

3. Discharge the high voltage capacitor before touching any oven components or wiring.

(1) Check the earthed.

Do not operate on a two-wire extension cord. The microwave oven is designed to be used with earthed. It is imperative, therefore, to makes sure it is earthed properly before beginning repair work.

(2) Warning about the electric charge in the high voltage capacitor.

For about 30 seconds after the operation stopped and electric charge remains in the high voltage capacitor. When replacing or checking parts, short between oven chassis and the negative high terminal of the high voltage capacitor, by using a properly insulated screwdriver to discharge.

4. When the 12A fuse is blown out due to the operation of the monitor switch; replace primary interlock switch, secondary interlock switch and interlock monitor switch.

5. After repair or replacement of parts, make sure that the screws are properly tightened, and all electrical connections are tightened.

6. Do not operate without cabinet.

CAUTION

Service personnel should rem ove their watches whenever w orking close to or replacing the m agnetron.

WARNING

When servicing the appliance, need a care of touching or replacing high potential parts because of electrical shock or exposing m icrowave. These parts are as follows - HV Transformer, Magnetron, HV Capacitor, HV D iode, H V Fuse.



+ 17 hidden pages