Daewoo DLA-32C7LAB Schematic

Caution

: In this Manual, some parts can be changed for improving. their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List)in Service Information Center.

Service Manual

LCD TV

CHASSIS :

Model :

S/M NO. : TSL900AEF0

DLA-32C7LAB DLA-32C7LABD DLA-37C7LAB DLA-37C7LABD DLA-42C7LAB DLA-42C7LABD

Dec. 2007

SL-900A

Contents

1. Safety Precaution 3

2. Preliminary Troubleshooting 4

3. Product Specification 5

1) Standard of Product 5

2) Available Input Signal 6

3) Available PIP Mode 6

4) Closed Caption Specification 7

5) V Chip(Parent Control) Specification 8

4. Service Remote Controller 9

1) Key Arrangement 9

2) Service Mode Data 10

5. Block Diagram 12

6. Hardware Troubleshooting : Digital Board 13

7. Hardware Troubleshooting : SMPS 18

1) FEL-3237UL : DLA-32/37C7LABD 18

2) FEL-4247UL : DLA-42C7LABD 20

8. Bill Of Materials 22

1) DLA-32C7LABD 22

9. Software Upgrade Methord 31

1) Flash Upgrade 35

10. Mechanical Development Figure 41

1) DLA-32C7LABD 41

2) DLA-37C7LABD 42

3) DLA-42C7LABD 43

11. Hanger Unit Manual

1. Safety Precaution

-3-

(1) When moving or laying down a LCD Set, at least two people must work together. Avoid any

impact towards the LCD Set.

(2) Do not leave a broken LCD Set on for a long time. To prevent any further damages, after

checking the condition of the broken Set, make sure to turn the power (AC) off.

(3) When opening the BACK COVER, you must turn off power (AC) to prevent any electric

shock.

(4) When loosening screws, check the position and type of the screw. Sort out the screws and

store them separately for reassembling. Because screws holding PCBs are working as electric circuit grounding, make sure to check if any screw is missing when assembling / reassembling. Do not leave any screws inside the set.

(5) A LCD Set contains different kinds of connector cables. When connecting or disconnecting

cables, check the direction and position of the cable beforehand.

(6) Connect/disconnect the connectors slowly with care especially FFC (film) cables and FPC

cables. Do not connect or disconnect connectors instantaneously with force, and handle them carefully for reassembling.

(7) Connectors are designed so that if the number of pins or the direction does not match,

connectors will not fit. When having problem in plugging the connectors, check their kind, position, and direction.

2. Preliminary Troubleshooting

-4-

1) LCD TV does not response or remote controller does not work.

- Check the power cord to be plugged.

- Check the battery of the remote controller.

2) Sound is discontinuous or broken sometimes.

- Check if [SOUND] -> [AVC] is [ON].

- Set the sound effect into 'F Mono'.

- Set the [SOUND] -> [Digital Volume] into proper value.

- [Digital Volume] is enabled only in digital program.

3) Picture of digital program is sometimes broken and sound is discontinuous.

- Digital program has a little problem because of signal receiving status.

- Check if the RF cable is correctly connected.

- Ask for the broadcasting station if the RF cable connection has no problem.

4) Picture of analog program is noisy.

- Check the RF cable connection.

- Check if [Picture] -> [N.R] is ON.

- Change the [Channel] -> [Fine Tune] value.

5) Sound is not generated in HDMI mode.

- Reconnect HDMI jack.

- DVI signal has no sound. Check the output signal of device to be connected to LCD TV.

- If you want to use DVI-HDMI cable, you should also connect audio cable into the LCD TV.

6) In spite of 'Auto Setup', picture size is not completely adapted to the screen in PC mode.

- Check if the input signal is available.

- Ensure that the desktop has no black area.

- Some errors (picture position problem) will be occurred according to certain video card. In this case, you should adjust 'Frequency' control.

7) In spite of 'Auto Setup', picture is not clear in the PC mode.

- Adjust 'Phase' control.

3. Product Specification

-5-

1) Standard of Product

Owing to our policy of continuous improvement, specifications may change.

Features DLA-32C7LABD DLA-37C7LABD DLA-42C7LABD

LCD Panel Panel Model

LC320W01-SLA1(A-/M) LC370WX4-SLA1(A-/M)

LC420WX7-SLA1(A-/M)

Screen Size 81.28 cm 93.98 cm 106.68 cm

Aspect Ratio 16:9

Resolution 1366 x 768 (WXGA)

Pixel Pitch

170.25µm X 510.75µm 0.200mm X 0.600mm 0.227mm X 0.681mm

Contrast Ratio 3000 : 1 (MAX)

TV System Receiving NTSC, ATSC

System

LVDS Cable FL-X30SSL-HF

LVDS B+ +12V

Input Connector RF 75 Ohm Coaxial

S-Video / Video 2

Component RCA X 2

PC RGB D-Sub X 1

PC Audio 3.5 mm Mini-Jack

HDMI 1

Output SPDIF Optical- Jack

Connector Headphone X

Monitor - out 1

Sound Output Max. 10W

Power Module Model FEL-3237UL FEL-3237UL FEL-4247UL

Power Max. 120 W 150 W 200 W

Consumption Power Source 100 - 124V~, 50/60Hz

Dimension Set Dimension

806 X 628.5 X 240 940 X 720 X 328.7 1037 X 791 X 329

(W x H x D) (with stand)

Product Specification

-6-

2) Available Input Signal i) TVMode

Ø Color Standard : NTCS, ATSC Ø Reception Channel : Ch 2~13 (VHF), Ch 14~69 (UHF), Ch 1, 14~125(Cable) Ø Sound Transmission System : FM Mono, 2 Carrier, Dolby Digital Ø IF &Subcarrier :

G PIF : 45.75MHz G SIF : 41.25MHz G Sound Subcarrier : 4.5MHz, 4.72 MHz G Color Subcarrier : 3.58MHz G DTV IF : 44MHz (5.38 MHz)

ii) Multimedia Mode

*Multi Input Resolution Aviable in LCD TV

Resolution V-freq HDMI PC(D-Sub) Component Standard

640 X 480 60Hz O O X VESA Standard

75Hz O O X VESA Standard

800 X 600 60Hz O O X VESA Standard

75Hz O O X VESA Standard

1024 X 768 60Hz O O X VESA Standard

75Hz O O X VESA Standard

1280 X 768 60Hz O X X VESA Standard

75Hz O X X VESA Standard

1280 X 1024 60Hz O O X VESA Standard

75Hz O O X VESA Standard

720 X 480i 60Hz X X O

720 X 480P 60Hz O O O

1280 X 720P 60Hz O O O

1920 X 1080i 60Hz O X O

1920 X 1080p 60Hz O X O

3) Available PIP Mode

MODE ATV DTV VIDEO 1 VIDEO 2 COMP. 1 COMP. 2 HDMI PC

ATVXXXXXXO X

DTV X X OOOOXX

VIDEO 1 X O XXXXO X

VIDEO 2 X O XXXXO X

COMP. 1 X O XXXXO X

COMP. 2 X O XXXXO X

HDMI O X OOOOXX

PC X O XXXXO X

Product Specification

-7-

4) Closed Caption SPEC i) DIGITAL(ATSC) standard inspection pattern :

CC708 SPEC STREAM(release to GUMI factory : 2007.02.02) ii) The Caption feature doesn’t work in COMPONENT, HDMI, and PC modes. iii) The availability of captions depends on the program being broadcast. iv) Caption lables and respective meanings.

Ø Analog (NTSC) :

G CC1 : The Primary Synchronous Caption Service.

These are captions in the primary language that must be in sync with the sound, preferably matched to a specific frame.

G CC2 : The Special Non-Synchronous Use Captions.

This channel carries data that is intended to augment information carried in the program.

G CC3 : Secondary Synchronous Caption Service.

Alternate program-related caption data, typically second language captions.

G CC4 : Special Non-Synchronous Use Captions.

Similar to CC2.

Ø Digital (ATSC) :

G Service 1 : Primary Caption Service This service contains the verbatim,

or near-verbatim captions for the primary language being spoken in the accompanying program audio.

G Service 2 : Secondary Language Service.

This service contains caption in a secondary language which are translations of the captions in the Primary Caption Service.

G The other service sub-channels are not pre-assigned.

It is up to discretion of the individual caption provider to utilize the remaining service channels.

v) Caption style

Ø Default means to follow the standard set by the broadcaster.

G Text Size : This option consists of Default,Small,Standard,and large.

The default is Standard.

G Text Font : This option consists of Default,

Font 1~7.You can change the font you want.

G Text Color : This option consists of Default, White, Black, Red, Green, Blue, Yellow,

Magenta, and Cyan. You can change the color of the letter.The default is White.

G BG Color : This option consists of Default, White, Black, Red, Green, Blue, Yellow,

Magenta, and Cyan. You can change the background color of the caption. The default is Black.

G BG Opacity : This option consists of Default, Rich, Light, and Transparent.

You can change the background opacity of the caption.

Product Specification

-8-

5) V Chip(Parental Control) SPEC i) The rating doesn't work in PIP/POP mode. Reservse case is the same. ii) The rating setting is possible only on the menu. iii) Inital password : 2-2-1-1. iv) Universal key cord (When user does not know password) : 5-4-2-2. v) The TV Parental Guidelines.

Ø Labels : TV-Y, TV-Y7, TV-G, TV-PG, and TV-14, TV-MA, FV, D, L, S, V

G TV-Y : All Children. Program is designd to be appropriate for all children. G TV-Y7 : Directed to Older Children.

Program is designd for children age 7 and above.

G TV-G : General Audience.

This Program contains material that parents ma find suitable to yonger children.

G TV-PG : Parental Guidance Suggested.

This Program contains material that parents may find.

G TV-14 : Parents Strongly Cautioned.

This Program contains some material that many parents wound find unsuitable for children under 14 years of age.

G TV-MA : Mature Audience Only.

This Program is specifically designd to be viewed by adults and therefore may be unsuitable for children under 17.

G FV : Fantasy violence / D : Sexually Suggestive Dialog / L : Adult Language /

S : Sexual situation / V : Violence

vi) The Movie ratings

Ø Labels : TV-Y, TV-Y7, TV-G, TV-PG, and TV-14, TV-MA, FV, D, L, S, V

G G : General Audiences.All ages admitted. G PG : Parental Guidance Suggested.

Some material may not be suitable for children.

G PG-13 : Parents Strongly Cautioned.

Some material may be inappropriate for children under 13.

G R : Restricted.

Under 17 requires accomanying parent or adult guardian.

G NC-17 : No children 17 and under admitted. G X : Adults only. G NR : Not rated.

4. Service Remote Controller

-9-

1) Key Arrangement



Chset/Gumi

Recall

HEAT-RUN

Language

No Function

User Reset

Volume

Auto Calibration

Picture

No Function

SVC Menu

Factory Reset

Service Remote Controller

-10-

2) Service Mode Data

To enter SERVICE MODE, A. Press “<VOL” -> “MUTE” -> “DISPLAY” -> “MUTE” button of remote controller(R-55M15) B. Press “S9” button of SERVICE REMOTE CONTROLLER.

Content Default Value Description

Pw388_1 Sub Bias 32

For BRIGHTNESS adjustment (All inputs)

Sub Gain 74

For CONTRAST adjustment (All inputs)

Bias R 35

For R BRIGHTNESS adjustment (All inputs)

Bias G 32

For G BRIGHTNESS adjustment (All inputs)

Bias B 32

For B BRIGHTNESS adjustment (All inputs)

Gain R 36

For R CONTRAST adjustment (All inputs)

Gain G 32

For G CONTRAST adjustment (All inputs)

Gain B 52

For B CONTRAST adjustment (All inputs)

Pw338_2 Sub Bias 32

For Bias adjustment of SUB PICTURE(PIP)

Sub Gain 64

For Gain adjustment of SUB PICTURE(PIP)

PwFrontEND_1 R Offset 411

G Offset 408

B Offset 393

R Gain 280

G Gain 269

B Gain 269

Y Offset 435

Pb Offset 534

Pr Offset 544

Y Gain 352

Pb Gain 369

Pr Gain 379

RGB Auto Cal >> Ready

YPrPb Auto Cal >> Ready

PwFrontEnd_2 AV Brt 128

AV Brightness adjustment

AV Cont 128

AV Contrast adjustment

AV Color7.5 IRE On

AV Color adjustment

COMP_SOG_TH 4

Component Sync. Threshold value adjustment

Msp46X0 Sc pScale 0

Prescale adjustment for external input (AV, Component, PC etc.)

Fm pScale 12

FM/AM prescale adjustment

HDMI pScale 32

BBE level control(disable)

BBE Level 30

HDMI prescale adjustment

Mvoice Level 12

Mvoice level control

Audio Delay 15

Sound delay control

Stereo ID 10

Stereo check

Misc DECODER Version : MP 200#-##-##-##

MCU Version: LPP 200#-##-##-##

Tst Ptrn AT >>

Tst Ptrn MA >>

TV Auto Off On

EDID Write Ready

*RGB offset values will be set by

executing “RGB Auto Cal” in service mode.

*YPbPr offset values will be set by

executing “YPbPr Auto Cal” in service mode.

*The automatically set offset values

may different from the default value depend on B/D. However, the main B/D should be replaced or contact R&D center in Korea if the OFFSET values differ more than

20 from default value.

Service Remote Controller

-11-

Content Default Value Description

Debug Enable Off

Smart ICON Status Off

Smart ICON Enable On

Panel Type 32”, 37”, 42”

Demodulator Master Lock Lock/Unlock

E/Q Lock Lock/Unlock

FEG Lock Lock/Unlock

Sync Lock Lock/Unlock

Mode 8VSB

SNR ##.# dB

IF AGC Level #.####

Pot PER #.####

Error Count #

Post BER #.####

Carrier Offset #

Ch Freq ###.####MHz

Reset Level1>> Resets all data in E2PROM other than HDCP key, EDID, RGB offset

and YPbPr offset of FrontEnd_1.

Level2>> Resets all data in E2PROM other than the exception of Level 1

andPw338B_1.

Factory>> Resets the data of auto search, language setting, time setting, and

the user menu values that could be reset by ‘Initialize’ function in Feature mode.

DTV MODE MENU

-12-

5. Block Diagram

-13-

6. Hardware Troubleshooting : Digital Board

1) In spite of sound output, the screen is black.

1.1 In case of ATV, DTV, VIDEO and COMPONENT mode.

START

Check the SMPS

and input voltage

IC501 Problem.

Replace the Main PCB

IC501 Problem.

Replace the Main PCB

1) TV mode : Check the path from Pin 9 of TU101 to Pin J1 of IC501

2) Component mode : Check the path from input jack to Pin U2,U3

,V2(COMP1) and R1,R2,T1(COMP2) of IC501

3) Video mode : Check the path from input jack to Pin M3(Video1)

and L3(Video2) of IC501

Perhaps Connector and Cable

Problem.

Replace the Main PCB

Check

the input power of

IC501 is correct

Yes

Check

the LVDS connector and cable

is correct

Is the input signal of IC501 normal?

Check

the LVDS signal output of IC501 is correct

(Use RC450~RC459)

Yes

-14-

Hardware Troubleshooting : Digital Board

1.2 In case of PC and HDMI mode

START

Check the input resolution

of external device

IC501 Problem.

Replace the Main PCB

IC501 Problem.

Replace the Main PCB

1) PC mode : Check the path from Jack to Pin R3, P2

and N1 of IC501

2) HDMI mode : Check the path from input jack to Pin

B1, A1, B3, A3, B5, A5, B7, A7 and F4 of IC501

Perhaps Connector and Cable

Problem.

Replace the Main PCB

Check

PC/HDMI resolution to

available resolution in

LCD TV

Yes

Check

the LVDS connector and cable

is correct

Is the input signal of IC501 normal?

Check

the LVDS signal output of IC501 is correct

(Use RC450~RC459)

Yes

Check the SMPS and

input voltage

Check

the input power of

IC501 is correct

Yes

-15-

Hardware Troubleshooting : Digital Board

1.3 In case of DTV mode

START

Select Air/Cable in Ant. Set correctly

Check the SMPS and input voltage

IC501 Problem.

Replace the Main PCB

Check the path from

TU101 to IC101

Check

the SNR is over 15dB

The signal quality is poor.

1. Check the ANT or its connection is correct

2. Consult a local installer.

Perhaps Connector and Cable

Problem.

Replace the Main PCB

Check

the “Ant. Set” is correct

in Menu

Yes

Check

the LVDS connector and cable

is correct

Check

the LVDS signal output of IC501 is correct

(Use RC450~RC459)

Yes

Check

the input power of

IC501 is correct

IS Lock status "LOCK"

in Service Mode(S9)-Demodulator?

Yes

Check the path from IC201 to IC501

Yes

Does

digital signal input from IC201

to IC501

Check the path from IC201 to IC501

Yes

Does

TS signal input from IC101

to IC201

Yes

-16-

Hardware Troubleshooting : Digital Board

2) In spite of picture display, the sound is not generated.

START

1. Confrim AC connection

2. Confrim Power S/W on

3. Check Video or other PCBs

Check the connection of jack

Does screen appear?

Yes

Is the Sound input Jack

correctly connected?

Check the connection of speaker

Yes

Is the speaker correctly

connected?

Check the SMPS and input voltage

Yes

Check

the input power of IC702 is normal

(Pin 6, 7, 12, 13)

Check the path from IC702 to Speaker

Check

the signal output of IC702 is normal

(Pin 2,3,8,9,10,11,16,17)

Yes

Perhaps IC702 problem.

Replace main PCB

Check

the signal output of IC701 is normal

(Pin 34, 36)

Yes

Perhaps IC701 problem.

Replace main PCB

Digital TV mode : Check the path from IC701 to IC201

HDMI mode : Check the path from IC701 to IC501

Analog TV mode : Check the path from IC701 to TU101

Video, Component mode : Check the path from

each Pin of IC701 to each jack

Check

the input signal of IC701 is

normal

Yes

-17-

LCD PANEL BACKLIGHT INVERTER CHECK

* Pin 14 is Status Output of Backlight Inverter.

Status Output of Pin 14

Normal 3.0V to 5.0V

Abnormal 0V to 0.7V

-18-

7. Hardware Troubleshooting : SMPS

1) FEL-3237UL : DLA-32/37C7LABD

'CHECKING FLOW ABOUT INFERIOR SMPS' (MODEL NAME : FEL-3237UL)

PAGE : 1/2

1. Stand-by 5V is working out.

A. Can you check In-put voltage(DC) of the capacitor(Location No. : C22)?

2. MAIN Out-put voltage is working out but Stand-by 5V is working.

A. Is Power On signal(3.3V) supplied to Base of Q7?

YES

YES 1.1 Checking open and short of Out-put side wire cable.

1.2. Checking open and short of the around parts that was connected IC1(STR-A6252). (Location No. :R12,ZD1,D5,D7)

1.3. Checking open and short of IC1's each pins.

1.4 Checking open and short of D15 each pins.

1.5. Can you check the Fuse(F1) condition(open and short)?

YES : Checking 1.2 item after changing FUSE. NO : Checking 1.5 item.

1.6. Checking open and short of BD.

YES : Changing BD. NO : Checking open and short of Z1, LF1, LF2.

A. Can you check that Vcc voltage of IC1 was supplied from DC15V to DC27V?

YES

2.1. Can you check the Q2's condition(open and short)?

YES : Changing Q2. NO : Checking 2.2 item.

2.2. Can you check the ZD7's condition(open and short)?

YES : Checking ZD7. NO : Checking 2.4~2.5 item.

YES 2.3. changing Q7.

B. Can you check the Q7's condition(open and short)?

C. Can you check that Vcc voltage of IC2's No.8pin was supplied from DC10V to DC18V?

2.4. Checking open and short of the around parts that was connected IC2(L6565). (Location No. :ZD4,ZD6,D3,D4,R50,R8D1,D2)

2.5. Checking open and short of IC1's each pins.

YES 2.6. Checking open and short of MAIN BOARD.

2.7. Checking open and short of MAIN BOARD.

-19-

Hardware Troubleshooting : SMPS

'CHECKING FLOW ABOUT INFERIOR SMPS' (MODEL NAME : FEL-3237UL)

PAGE : 2/2

3. 5V's Out-put voltage is measured too high or low.

A. Checking open and short of IC10,IC5.

B. Checking open and short of R25,R23.

C. Checking open and short of IC1.

4. 5V's Out-put voltage is work with intermittent mode.

A. Is R12's condition good from open and short?

YES : changing R12. NO : Checking 1.2 and 1.3 items.

(Checking open and short of MAIN BOARD if that 1, 2 and 1.3 items are no problem.)

5. Out-put voltage(DC12v, 24v, 15v) is measured too high.

A. Checking open and short of IC9.

B. Checking open and short of R39, R40.

C. Checking open and short of IC4.

-20-

Hardware Troubleshooting : SMPS

2) FEL-4247UL : DLA-42C7LABD

'CHECKING FLOW ABOUT INFERIOR SMPS' (MODEL NAME : FEL-4247UL)

PAGE : 1/2

1. Stand-by 5V is working out.

A. Can you check In-put voltage(DC) of the capacitor(Location No. : C23)?

YES

YES 1.1 Checking open and short of Out-put side wire cable.

1.2. Checking open and short of the around parts that was connected IC3(STR-A6252). (Location No. : R4, R5, D4, D5, D7)

1.3. Checking open and short of IC3's each pins.

1.4. Checking open and short of 5V's Out-put diode. (Location No. : D13)

1.5. Can you check the Fuse(F1) condition(open and short)?

YES : Checking 1.2 item after changing FUSE. NO : Checking 1.6 item.

1.6. Checking open and short of BD1, BD2.

YES : Changing BD1, BD2. NO : Checking open and short of Z1,LF1,LF2 ,C1,C2

A. Can you check that Vcc voltage of IC3 was supplied from DC15V to DC27V?

YES

2.1. Can you check the IC9's condition(open and short)?

YES : Changing IC9. NO : Checking 2.2 item.

2.2. Can check the voltage(AC 400V) of AC rectifying side C23?

YES : Checking 2.5 item.

NO : Checking 2.5 item after checking the conditions(open and short) of the around parts that was

connected IC1. (Location No. :R14,R51,Q1,Q5,D1,D23,D12, IC1)

YES 2.3. changing Q4.

B. Can you check the Q4's condition(open and short)?

C. Can you check that Vcc voltage of IC2's No.12pin was supplied from DC10V to DC12V?

2.4. Can you see the square wave(400mV, 40kH) of Q2's source side when DC 13V was supplied to IC2's No.12pin from DC POWER SUPPLY? (CAUTION : Test do it after AC Power Off)

YES : Checking 2.1 item after checking diode's condition(open and short) of MainOut-put side.

(Location No. :D14,D15,D16,D17,D18)

NO : Checking open and short of the around parts that was connected IC2.

(Location No. :Q2,Q3,D9,D10,D19,D20,F2)

YES 2.5. Checking open and short of MAIN BOARD.

2.6. Checking open and short of MAIN BOARD.

2. MAIN Out-put voltage is working out but Stand-by 5V is working.

A. Can you check that it is working normal at Power On after dischanging for 1 minute from Power Off?

YES : It's protection due to out-put short of the moment through worker's carelessness.

NO : Checking 2.1 item.

A. Is Power On signal(3.3V) supplied to Base of Q4?

-21-

Hardware Troubleshooting : SMPS

'CHECKING FLOW ABOUT INFERIOR SMPS' (MODEL NAME : FEL-4247UL)

PAGE : 2/2

3. 5V's Out-put voltage is measured too high or low.

A. Checking open and short of IC7.

B. Checking open and short of R49,R50.

C. Checking open and short of IC6.

4. 5V's Out-put voltage is work with intermittent mode.

A. Is R5's condition good from open and short?

YES : changing R5. NO : Checking 1.3 and 1.4 items.

(Checking open and short of MAIN BOARD if that 1, 3 and 1.4 items are no problem.)

5. Out-put voltage(DC12v, 24v, 15v) is measured too high.

A. Checking open and short of IC5.

B. Checking open and short of R44, R43.

C. Checking open and short of IC4.

-22-

8. Bill Of Materials

M321 4853296800 BRKT STAND SECC T1.6 M321A 7172401452 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK 3CR M322 4853296900 BRKT STAND BOX SECC T1.0 M322A 7172401452 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK 3CR M322B 7172401452 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK 3CR M381C 7071400851 SCREW MACHINE PAN 4X8 SW MFZN 3CR M382 4853829102 FRAME BAR SECC T=1.2(A-2 FINAL:LPL PANEL) M382B 7172401452 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK 3CR M491B 7172401452 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK 3CR M541 4855421200 SPEC PLATE P.E 149X59 M721 4851957409 SHIELD CASE AS 7255702+5944609 M721A 7173301052 SCREW TAPPTITE TT2 BIN 3X10 MFZN BK 3CR M723 4857255904 SHIELD JACK AL 1100 T=1.0 (A-5 : SL-500P) M723A 7178300852 SCREW TAPPTITE TT2 WAS 3X8 MFZN BK 3CR M723B 7178300852 SCREW TAPPTITE TT2 WAS 3X8 MFZN BK 3CR MK001 4850K01700 CORE FERRITE BNF-1130 MK002 4850K01700 CORE FERRITE BNF-1130 MK003 4850K01700 CORE FERRITE BNF-1130 MK004 4850K01900 CORE FERRITE BNF-1730 MK005 4850K01900 CORE FERRITE BNF-1730 MK006 4850K01700 CORE FERRITE BNF-1130 P401A 4850710N33 CONNECTOR 12505HS-10+12505HS-10+ULW=800 P703A 4850703N44 CONNECTOR SMH250-03+YRT205+YRT110+USW=600 P704A 4850704S80 CONNECTOR SMH250-04+YRT205+YRT110+USW=500 P803A 4850706S36 CONNECTOR 12505HS-06+12505HS-06+ULW=900 P804A 4850705N28 CONNECTOR 12505HS-05+12505TS+ULW=900 P805A 4850715S03 CONNECTOR SMH250-15+SMH250-15+ULW=300 P805B 4850712S11 CONNECTOR 20022HS-12S+20022HS-12S+ULW=800 P805C 4850714S06 CONNECTOR 20022HS-14+20022HS-12+ULW=300 PM100 4850M004PW MODULE POWER FEL-3237UL SP01 4858318510 SPEAKER SP-45165F01C SP01A 4856017800 SCREW SPKR FIX SWRM+SECC 3CR SP02 4858318510 SPEAKER SP-45165F01C SP02A 4856017800 SCREW SPKR FIX SWRM+SECC 3CR V901 485LDAA320 LCD PANEL LC320W01-SLA1(A-/M) ZZ200 PTFMSJG293 MASK FRONT AS DLA-32C7LABD M201 4852094903 MASK FRONT FR HIPS BK M201A 4857743800 CUSION PANEL PVC 400 X 10 T=1.0 M201B 4857743900 CUSION PANEL PVC 300 X 10 T=1.0 M551 4855557201 DECO SENSOR GPPS M551A 7178301052 SCREW TAPPTITE TT2 WAS 3X10 MFZN BK 3CR M561 4855626000 MARK BRAND

SILVER DIA-CUTTING(DOUBLE FACED TAPE),L=85,P=30 M591 4855945901 DECO PLATE PC T=2.0 ZZ250 PTSNSWG293 STAND AS DLA-32C7LABD M213 4852177301 COVER STAND BASE HIPS BK M387 4853831001 FRAME STAND ABS BK M387A 7172401452 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK 3CR M521 4855219100 PLATE BASE STAND SECC T2.0 M521A 7115401051 SCREW TAPPING FLT 4X10 MFZN 3CR M521C 4852937500 RUBBER BOTTOM CR60 BK PHI 18.0 X T 3.0 ZZ290 PTMPMSG293 PCB MAIN MANUAL AS DLA-32C7LABD 100 2193110012 SOLDER WIRE SAC3000 200 2193110024 SOLDER WIRE SAC3005 300 2291050623 FLUX SOLDER LF SV-PBF-304P(0.823) 400 2291050312 FLUX SOLVENT S-3000 CE673 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) TP CE674 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) TP HS501 4957000800 HEAT SINK AL ANODIZHG+TAPE IC290 1R24FH1B-- IC PREAMP R24FH1B JK202 4959102340 JACK PHONE SPJ-358H(3.5 STRAIGHT) JK401 4859117950 JACK PIN DPSE-0415S JK402 4859118150 JACK PIN YPJ-02S43 (2P ST SHIELD) JK403 4859118150 JACK PIN YPJ-02S43 (2P ST SHIELD) JK404 4859118050 JACK PIN DPSE-9926S JK405 4859105340 JACK S-VHS DSW-10 (STRAIGHT) JK409 4959102340 JACK PHONE SPJ-358H(3.5 STRAIGHT) JK410 4959200160 CONN D-SUB SHF-015-B111-22/BR2-J0.6 JK802 4859201170 CONN OPTICAL SENSOR OJ107A-T050-SHS

LOC PART CODE PART NAME DESCRIPTION

JKJ01 4859105340 JACK S-VHS DSW-10 (STRAIGHT) JKJ02 4859112850 JACK PIN DPSS-0173(3P ST) JP401 4859295420 CONN WAFER 4602-04MV2-60-1 PLUG 4P ST JP601 4859295520 CONN WAFER 4602-02MV2-60-1 PLUG 2P ST L651 58C0000171 COIL CHOKE CH-C330W L652 58C0000171 COIL CHOKE CH-C330W L653 58C0000171 COIL CHOKE CH-C330W L654 58C0000171 COIL CHOKE CH-C330W LED13 DSPR39MVW- LED SPR-39MVW (DUAL) M232 4852333201 PANEL CTRL HIPS BK M371 4853748800 RETA PCB NYLON 66 M372 4956800200 CLAMP WIRE WS-A-2-19 M381 4853829001 FRAME MAIN PCB SECC T=1.2 (A-2 : 32C1/32C3) M381B 7178301052 SCREW TAPPTITE TT2 WAS 3X10 MFZN BK 3CR M381C 7008300851 SCREW MACHINE WAS 3X8 MFZN 3CR M381D 4856815900 CLAMP WIRE EGI T0.4+TUBE+PIE 3.2 M491 4854964311 BUTTON CH ABS GY M491A 7178301051 SCREW TAPPTITE TT2 WAS 3X10 MFZN 3CR M720 4853294100 BRKT POWER SW SECC 1T M720A 7172401452 SCREW TAPPTITE TT2 TRS 4X14 MFZN BK 3CR P201 4859284420 CONN WAFER SMW250-03 P601 4859200420 CONN WAFER 4602-10MV2-60-1 PLUG 10P ST P703 4859284420 CONN WAFER SMW250-03 P704 4859284520 CONN WAFER SMW250-04 P805 4959203820 CONN WAFER SMW250-15 TU101 4859730730 TUNER DIGITAL TDVS-H707F(AT-CV-H-F) X101 5XJ49R38JE CRYSTAL QUARTZ HC-49/S 49.38111MHZ 30PPM X201 5XJ27R00AE CRYSTAL QUARTZ HC-49/S 27.000MHZ 10PF 30PPM X501 5XJ27R00AC CRYSTAL QUARTZ HC-49/S 27.000MHZ 15PF 20PPM X502 5XJ28R32GE CRYSTAL QUARTZ HC-49/S 28.322MHZ 30PPM 16PF X601 5XJ8R388JE CRYSTAL QUARTZ HC-49/S 8.388608MHZ 30PPM X701 5XJ27R00AC CRYSTAL QUARTZ HC-49/S 27.000MHZ 15PF 20PPM ZZ200 PTMPJ2G293 PCB MAIN CHIP B AS DLA-32C7LABD CC101 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC102 HCQK471JBA C CHIP CERA 50V CH 470PF J 1608 CC104 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC105 HCQK220JBA C CHIP CERA 50V CH 22PF J 1608 CC106 HCQK220JBA C CHIP CERA 50V CH 22PF J 1608 CC112 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC113 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC114 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC115 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC118 HCQK270JBA C CHIP CERA 50V CH 27PF J 1608 CC119 HCQK270JBA C CHIP CERA 50V CH 27PF J 1608 CC120 HCQK471JBA C CHIP CERA 50V CH 470PF J 1608 CC121 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC122 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC123 HCQK151JBA C CHIP CERA 50V CH 150PF J 1608 CC125 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC126 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC127 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC128 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC129 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC130 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC131 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC132 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC133 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC134 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC135 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC136 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC137 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC138 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC139 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC140 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC141 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC142 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC143 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608 CC144 HCBK104KBA C CHIP CERA 50V X7R 0.1MF K 1608

LOC PART CODE PART NAME DESCRIPTION

1) DLA-32C7LABD

+ 51 hidden pages