Page 1
Installation Manual
Dual Fuel Pro Range
DOP30**40D*
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 1Install_DOP30T940DS_DA_DG68-01457A_EN.indd 1 2022-10-11 오전 11:36:582022-10-11 오전 11:36:58
Page 2
WARNING: If the information in this manual is not followed exactly,
a re or explosion may result causing property damage, personal
injury or death.
• DO NOT store or use gasoline or other ammable vapors and
liquids in the vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch.
- DO NOT use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the re
department.
• Installation and service must be performed by a qualied
installer, service agency, or the gas supplier.
ANTITIP DEVICE
WARNING
ALL RANGES CAN TIP, RESULTING IN PERSONAL INJURY.
TIPPING RANGES CAN CAUSE BURNS FROM SPILLS,
PERSONAL INJURY, AND/OR DEATH.
INSTALL AND CHECK THE ANTI-TIP BRACKET FOLLOWING
THE INSTRUCTIONS AND TEMPLATE SUPPLIED WITH THE
BRACKET.
• To prevent accidental tipping of the range, attach an approved
anti-tip device to the oor. (See Installing the Anti-Tip Device
in the Installation Instructions.) Check for proper installation by
carefully tipping the range forward. The anti-tip device should
engage and prevent the range from tipping over.
• If the range is pulled out away from the wall for any reason,
make sure the anti-tip device is reengaged after the range has
been pushed back into place.
• Follow the installation instructions found in the Installation
Manual. Failure to follow these instructions can result in death,
serious personal injury, and / or property damage.
• DO NOT step / sit / lean on the door or drawer to prevent
accidental tipping of the range.
• Be sure your appliance is properly installed and grounded by a
qualied technician.
2 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 2Install_DOP30T940DS_DA_DG68-01457A_EN.indd 2 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 3
Contents
Before you begin 4
About this manual 4
Important safety information 4
Read all instructions before using this appliance 4
Symbols used in this manual 4
California Proposition 65 Warning 5
Commonwealth of Massachusetts 5
General safety 5
Fire safety 6
Gas safety 6
Electrical and grounding safety 7
Installation safety 7
Location safety 8
Cooktop safety 8
Oven safety 9
Self-cleaning oven safety 10
Storage drawer safety 10
Gas range components 11
Dual Fuel range specications 11
Installation requirements 12
Location requirements 12
Installation guide 13
To remove safely from the pallet 15
To avoid breakage 15
Gas requirements 16
Special gas requirements (gas models sold in Massachusetts) 17
Electrical requirements 17
Tools and materials 19
What’s in the box 19
Contents
Installation instructions 20
Installing your Dual fuel Range 20
English 3
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 3Install_DOP30T940DS_DA_DG68-01457A_EN.indd 3 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 4
Before you begin
Important safety information
Before you begin
About this manual
Read these instructions completely and carefully.
Important note to the installer
• Read all instructions contained in these installation instructions before
installing the range.
• Remove all packing materials from the oven compartments before connecting
the electric and gas supply to the range.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
• Installation of this appliance requires basic mechanical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
Important note to the consumer
Keep these instructions with your user manual for future reference.
• As when using any appliance generating heat, there are certain safety
precautions you should follow.
• Be sure your range is installed and grounded properly by a qualied installer
or service technician.
• Make sure the wall coverings around the range can withstand the heat
generated by the range.
• Cabinet storage space above the surface burners should be a minimum of
30 in (76.2 cm).
Important note to the servicer
The electrical diagram is in an envelope attached to the back of the range.
Read all instructions before using this appliance
• All electrical and gas equipment with moving parts can be dangerous. Please
read the important safety instructions for this appliance in this manual. The
instructions must be followed to minimize the risk of injury, death, or property
damage.
• Save this manual. Please Do Not Discard.
Symbols used in this manual
WARNING
Hazards or unsafe practices that may result in severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in electric shock, personal injury or
property damage
NOTE
Useful tips and instructions
These warning icons and symbols are here to prevent injury to you and others.
Please follow them explicitly. After reading this section, keep it in a safe place for
future reference.
4 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 4Install_DOP30T940DS_DA_DG68-01457A_EN.indd 4 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 5
California Proposition 65 Warning
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Commonwealth of Massachusetts
This product must be installed by a licensed plumber or gas tter qualied or
licensed by the State of Massachusetts. When using ball-type gas shut-off valves,
you must use the T-handle type. Multiple exible gas lines must not be connected
in series.
General safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• Do not touch any part of the range,
including but not limited to, oven
burners, surface burners, or interior
surfaces during or immediately after
cooking.
• Know the location of the gas shutoff valve and how to shut it off.
• Make sure the anti-tip device is properly installed on the range. See the
installation instructions for more information.
• Do not let children near, in, or on the range. Do not let children play with the
range or any part(s) of the range. Do not leave children unattended in an area
where the range is in use. For children’s safety, we recommend utilizing the
control/door lockout feature.
• Remove all packaging materials from the range before operating to prevent
ignition of these materials. Keep all packaging materials out of children’s
reach. Properly dispose the packaging materials after the range is unpacked.
• Do not store any object of interest to children on the cooktop or backguard
of the range. Children climbing on the range to reach items could be killed or
seriously injured.
• Do not operate the range if the range or any part of the range is damaged,
malfunctioning, or missing parts.
• Do not use the range as a space heater. This range is to be used for cooking
purposes only.
• Do not use oven cleaners or oven liners in or around any part of the oven.
• Use only dry pot holders.
• Do not use the range to heat unopened food containers.
• Do not strike the oven glass.
• When disposing of the range, cut off the power cord and remove the door.
• Unplug or disconnect power before servicing.
• Make sure all meat and poultry is cooked thoroughly. Meat should always be
cooked to an internal temperature of 160 °F (71 °C). Poultry should always be
cooked to an internal temperature of 180 °F (82 °C).
Important safety information
English 5
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 5Install_DOP30T940DS_DA_DG68-01457A_EN.indd 5 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 6
Important safety information
Important safety information
Fire safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• Do not store, place, or use ammable
or combustible materials such as
charcoal, paper, plastic, pot holders,
linens, curtains, gasoline or other
ammable vapors or liquids near or
inside the range.
• Do not wear loose tting or hanging
garments while using the range.
• To avoid grease buildup, regularly clean the vents.
• Do not let pot holders or other ammable materials touch a heating element.
Do not use a towel or other bulky cloths in place of a pot holder.
• Do not use water on a grease re. To put out a grease re, turn off the heat
source and smother the re with a tight-tting lid or use a multipurpose dry
chemical or foam-type re extinguisher.
• If a grease re should occur in the oven, turn off the oven by rotating the
mode selector knob to the OFF position. Keep the oven door closed until the
re goes out. If necessary, use a multipurpose dry chemical or foam-type re
extinguisher.
• Do not heat unopened food containers - buildup of pressure may cause
container to burst and result in injury.
Gas safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
If you smell gas:
• Close the valve and do not use the
range.
• Do not light a match, candle, or
cigarette.
• Do not turn on any gas or electric
appliances.
• Do not touch any electrical switches
or plug a power cord into an outlet.
• Do not use any phone in your building.
• Evacuate the room, building, or area of all occupants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the re department.
Checking for gas leaks
• Leak testing of the appliance shall be conducted according to the
manufacturer’s instructions. Do not use a ame to check for gas leaks. Use a
brush to spread a soapy water mixture around the area you are checking. If
there is a gas leak, you will see small bubbles in the soapy water mixture at
the leak point.
6 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 6Install_DOP30T940DS_DA_DG68-01457A_EN.indd 6 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 7
Electrical and grounding safety
Installation safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter or an
extension cord.
• Do not use a damaged power plug,
power cord, or loose power outlet.
• Do not modify the power plug,
power cord, or power outlet in any
way.
• Do not put a fuse in a neutral or ground circuit.
• Use a dedicated 240-volt, 60-Hz, 40-amp, AC, fused electrical circuit for this
range. A time-delay fuse or circuit breaker is recommended. Do not plug more
than one appliance into this circuit.
• Do not connect the ground wire to plastic plumbing lines, gas lines, or hot
water pipes.
• This range must be Earth grounded. In the event of a malfunction or
breakdown, grounding will reduce the risk of electrical shock by providing
a path for the electric current. This range is equipped with a cord having
a grounding plug. The plug must be rmly plugged into an outlet that is
properly installed and grounded in accordance with the local codes and
ordinances. If you are unsure whether your electrical outlet is properly
grounded, have it checked by a licensed electrician.
• Electrical service to the range must conform to local codes. Barring local
codes, it should meet the latest ANSI/NFPA No. 70 – Latest Revision (for the
U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions.
• It is the personal responsibility of the range owner to provide the correct
electrical service for this range.
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• Have your range installed and
properly grounded by a qualied
installer, in accordance with the
installation instructions. Any
adjustment and service should
be performed only by qualied
gas range installers or service
technicians.
• Do not attempt to service, modify, or replace your range or any part of your
range unless it is specically recommended in this manual. All other service
should be referred to a qualied technician.
• Always use new exible connectors when installing a gas appliance. Do not
use old exible connectors.
• Make sure the anti-tip device is properly installed on the range. See the
installation instructions for more information.
• Due to the size and weight of the range, have two or more people move the
range.
• Remove all tape and packaging materials.
• Remove all accessories from the cooktop and oven. Grates are heavy. Use
caution when handling them.
• Make sure no parts came loose during shipping.
Important safety information
English 7
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 7Install_DOP30T940DS_DA_DG68-01457A_EN.indd 7 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 8
Important safety information
Important safety information
• Make sure your range is correctly installed and adjusted by a qualied service
technician or installer for the type of gas (natural or LP) you will use. For
your range to utilize LP gas. The installer must replace the 6 surface burner
orices with the provided LP orice set. And reverse the GPR adapter. These
adjustments must be made by a qualied service technician in accordance
with the manufacturer’s instructions and all codes and requirements of the
authority having jurisdiction. The qualied agency performing this work
assumes the gas conversion responsibility.
• Installation of this range must conform with local codes or, in the absence of
local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest
edition. In Canada, installation must conform with the current Natural Gas
Installation Code, CAN/CGA-B149.1, or the current Propane Installation Code,
CAN/CGA-B149.2, and with local codes where applicable. This range has been
design-certied by ETL according to ANSI Z21.1, latest edition, and Canadian
Gas Association according to CAN/CGA-1.1, latest edition.
Location safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• This range is for indoor, household use
only. Do not install the range in areas
exposed to the weather and/or water.
• Do not install the range in a place
which is exposed to a strong draft.
• Select a level, well-constructed oor that can support the range’s weight.
Synthetic ooring, such as linoleum, must withstand 180 °F (82 °C)
temperatures without shrinking, warping, or discoloring. Do not install
the range directly over interior kitchen carpeting unless a sheet of ¼ inch
plywood or a similar insulator is placed between the range and carpeting.
• Select a location where a grounded, 3- prong outlet is easily accessible.
• If the range is located near a window, do not hang long curtains or paper
blinds on that window.
• For the range to ventilate properly, make sure the range’s vents are not
blocked or covered, and that there is enough clearance at the top, back, sides,
and underneath the range. The vents allow the necessary exhaust for the range
to operate properly with correct combustion and get the good cooking result.
• Make sure the wall coverings around the range can withstand heat up to
194 °F (90 °C) generated by the range.
• Cabinet storage above the surface of the range should be avoided. If cabinet
storage above the range is necessary: allow a minimum clearance of 30 inches
(76.2 cm) between the cooking surface and the bottom of cabinets; or install
a range hood that projects horizontally a minimum of 5 inches (12.7 cm)
beyond the bottom of the cabinets. For detail information, please refer to the
Minimum dimensions section on page 13.
Cooktop safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• Make sure all burners are off when not
in use.
• Do not use aluminium foil to line the
grates or any part of the cooktop.
• Do not leave burners unattended on
medium or high heat settings.
• Before igniting, make sure all burner
caps are properly in place and all
burners are level.
• Always use the Lite ( ) position when igniting the burners and make sure the
burners have ignited. If ignition fails, turn the knob to OFF and wait until the
gas has dissipated.
• When you set a burner to simmer, do not turn the knob quickly. Make sure the
ame stays on.
• Do not place any objects other than cookware on the cooktop.
8 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 8Install_DOP30T940DS_DA_DG68-01457A_EN.indd 8 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 9
• This cooktop is designed to cook with a wok or wok ring attachment. If foods
are amed, they should only be amed under a ventilation hood that is on.
• Before removing or changing cookware, turn off the burners.
• Remove food and cookware immediately after cooking.
• Before removing any parts of the burner for cleaning, make sure the range is
off and completely cool.
• After cleaning the burner spreader, make sure it is completely dry before re-
assembling.
• Make sure the spark mark on the dual burner spreader is placed beside the
electrode when it is assembled.
• To avoid carbon monoxide poisoning, do not pour water into the cooktop well
while cleaning.
• Select cookware that is designed for top-range cooking. Use cookware that is
large enough to cover the burner grates. Adjust the burner ames so that the
ames do not extend beyond the bottom of the cookware.
• To avoid cookware discoloration, deformity, and/or carbon monoxide
poisoning, do not use cookware that is exceedingly larger than the grate.
• Make sure cookware handles are turned to the side or rear of the cooktop, but
not over other surface burners.
• Stand away from the range while frying.
• Always heat frying oils slowly, and watch as they heat. If you are frying foods
at high heat, carefully watch during the cooking process. If a combination of
fats or oils is to be used during frying, mix them together before heating.
• Use a deep-fryer thermometer whenever possible. This prevents overheating
the fryer beyond the smoking point.
• Use a minimum amount of oil when shallow pan-frying or deep-frying. Avoid
cooking unthawed food or food with excessive amounts of ice.
• Before moving cookware full of fats or oils, make sure it has completely
cooled.
• To prevent delayed eruptive boiling, always allow heated liquids to stand at
least 20 seconds after you have turned off the burner so that the temperature
in the liquid can stabilize. In the event of scalding, follow these rst aid
instructions:
1. Immerse the scaled area in cool or lukewarm water for at least 10 minutes.
2. Do not apply any creams, oils, or lotions.
3. Cover with a clean, dry cloth.
Oven safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• Do not use the oven for non-cooking
purposes such as drying clothes or
storage. Use the oven for cooking
purposes only.
• Make sure the inner portion of the split
oven-rack is in the proper position
within the outer rack.
• Make sure the oven racks are placed on the same level on each side.
• Do not damage, move, or clean the door gasket.
• Do not spray water on the oven glass while the oven is on or just after you
have turned it off.
• Do not use aluminium foil or foil liners anywhere in the oven. Do not use
aluminium foil or like material to cover any holes or passages in the oven
bottom or to cover an oven rack.
• Stand away from the oven when opening the oven door.
• Keep the oven free from grease buildup.
• When repositioning the oven racks, make sure the oven is completely cool.
• To avoid damaging the burner control knobs, always bake and/or broil with
the oven door closed.
• Do not broil meat too close to the burner ame(or heater). Trim excess fat
from meat before cooking.
• When using cooking or roasting bags in the oven, follow the manufacturer’s
directions.
• Keep oven vent ducts which is below the controlbox unobstructed. This area
could become hot during oven use. Never block this vent or place plastic or
heat-sensitive items on it.
Important safety information
English 9
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 9Install_DOP30T940DS_DA_DG68-01457A_EN.indd 9 2022-10-11 오전 11:36:592022-10-11 오전 11:36:59
Page 10
Important safety information
Self-cleaning oven safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• The self-cleaning feature operates the
oven at temperatures high enough
to burn away food soils in the oven.
The range is extremely hot during a
self-cleaning cycle. Do not touch any
surfaces of the range during a selfcleaning cycle.
Gas range components
• Keep children away from the oven during a self-cleaning cycle.
• Before starting a self-cleaning cycle, remove all racks, cookware, and utensils
from the oven. Only porcelain-coated oven racks may be left in the oven.
• Before starting a self-cleaning cycle, wipe grease and food soils from the
oven.
• Do not put the lower drawer into the oven cavity when you run a self-
cleaning cycle.
• When opening the door after a self-cleaning cycle, stand away from the oven.
• If the self-cleaning cycle malfunctions, turn off the oven, disconnect the power
supply, and contact a qualied service technician.
Storage drawer safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the
following precautions.
• Do not use the drawer for non-cooking
purposes such as drying clothes or
storage. Use the drawer for cooking
purposes only.
• Do not touch the interior drawer surface or heating element.
• To avoid steam burns, use caution when opening the drawer.
• Do not use aluminium foil to line the drawer.
• Do not use the drawer in the oven. Do not put the drawer in the oven during a
self-cleaning cycle.
• Do not leave containers of fat drippings in or near the drawer.
10 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 10Install_DOP30T940DS_DA_DG68-01457A_EN.indd 10 2022-10-11 오전 11:37:002022-10-11 오전 11:37:00
Page 11
Gas range components
Dual Fuel range specications
MODEL DOP30**40D*
Description Dual fuel Range
Overall dimensions 29 ⁄ in (W) × 36 ⁄ in (H) × 26 ⁄ in (D)
761 mm (W) × 932 mm (H) × 669 mm (D)
Electrical Refer to the rating label.
Gas, NG (natural gas) 5–13 in WC
Gas, LP (liquid propane) 10–13 in WC
Surface burners (NG) (LF)–16,000 BTU / (LR)–16,000 BTU
(RF)–23,000 BTU / (RR)–9,500 BTU
Surface burners (LP) (LF)–15,000 BTU / (LR)–15,000 BTU
(RF)–17,500 BTU / (RR)–9,500 BTU
Oven heater Bake - 3000 W
Broil - 4200 W
29 15/16"
(76.1 cm)
"
16
1
/
27
(68.7 cm)
"
8
3
/
26
(66.9 cm)
" (72.5 cm)
16
9
/
28
With handle
Without grate
36 1/16" (91.5cm) Min.
36 11/16" (93.2cm) Max.
With grate
15
37
/16" (96.3cm) Min.
38 9/16" (98.0cm) Max.
" (73.0 cm)
4
3
/
28
With knobs
49"
(124.7 cm)
Door fully open
Gas range components
English 11
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 11Install_DOP30T940DS_DA_DG68-01457A_EN.indd 11 2022-10-11 오전 11:37:002022-10-11 오전 11:37:00
Page 12
Installation requirements
Installation requirements
Location requirements
Clearances and dimensions
NOTE
• For OTR over Gas Stove, please follow local GAS CODE.
• BEFORE YOU BEGIN to install this appliance, refer to the following information,
dimensions, and clearances. Do not locate the range where it may be subject
to strong drafts. Provide adequate clearances between the range and adjacent
combustible surfaces. These dimensions must be met for safe use of the range.
The location of the electrical outlet and gas piping may be adjusted to meet
the following dimensions and clearances.
• For installation in Canada, a free-standing range is not to be installed closer
than 4.7 in (12 cm) from any adjacent surface.
36 in
(91.4 cm)
4 in*
(10.2 cm)
24 in
(61 cm) Lower
Cabinet Depth
30 in
(76.2 cm)
(15.2 cm)
6 in*
30 in (76.2 cm)
30 in (76.2 cm)
18 in
(45.7 cm)
0 in (0 cm)
Clearance Below
Cooking Top
and at Rear and
Sides of Range
13 in (33 cm)
Overhead
Cabinet Depth
24.2 in
(61.5 cm)
0 in (0 cm)
CAUTION
Installation requirements
This range has been designed to comply with the maximum allowable wood
* Side clearance above cooking surface to any objects, i.e., wall.
cabinet temperature of 194 °F (90 °C). Make sure the wall covering, countertops,
and cabinets around the range can withstand the heat (up to 194 °F [90 °C])
generated by the range. If not, discoloration, delamination, or melting may occur.
CAUTION
DO NOT install the oven so that the door is ush with the cabinet.
12 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 12Install_DOP30T940DS_DA_DG68-01457A_EN.indd 12 2022-10-11 오전 11:37:002022-10-11 오전 11:37:00
Page 13
Minimum dimensions
Installation guide
CAUTION
• If overhead cabinets are installed, a range hood should also be installed
and project horizontally a minimum of 5" (12.7 cm) beyond the front of the
cabinets. Hood is necessary to dissipate any heat buildup in the overhead
cabinets to prevent possibility of re, personal injury and/or death. The
ventilating hood must be constructed of sheet metal not less than 0.0122"
thick and installed above the cooktop with a clearance of not less than ¼"
between the hood and the underside of the combustible material or metal
cabinet. The hood must be at least as wide as the appliance and centered over
the appliance. Clearance between the cooking surface and the ventilation hood
surface must never be less than 24".
• Exception 1 : Installation of a listed microwave oven or cooking appliance
over the cooktop shall conform to the installation manual provided with the
appliance.
- 30" (76.2 cm) minimum clearance between the top of the cooking
surface and the bottom of an unprotected wood or metal cabinet; or If
30" (76.2 cm) clearance is not possible, minimum of 24" (61 cm) can be
used when the bottom of the wood or metal cabinet is protected by not
less than ¼" (0.64 cm) ame-retardant millboard covered with not less
than no. 28 MSG sheet steel, 0.015" (0.038 cm) stainless steel, 0.024"
(0.061 cm) aluminum, or 0.020" (0.051 cm) copper.
- 18" (45.7 cm) of minimum clearance between the countertop and the
adjacent cabinet bottom.
• Exception 2 : For island installation, maintain 2½" minimum from cutout
to back edge of countertop and 4" minimum from cutout to side edges of
countertop.
IMPORTANT:
To eliminate the risk of burns or re caused by reaching over heated surface units,
avoid having cabinet storage space located above the surface units. If you have cabinet
storage space over the heating elements, you can reduce the risk by installing a range
hood that projects horizontally a minimum of 5 inches beyond the bottom of the
cabinets.
Installation guide
3"
25"
24"
36 1/4"-37
(921.2 mm)
29 15/16"
(761.0 mm)
A: Cabinet opening 30” (76.2)
IMPORTANT: If your cabinet have height over 37”, this range cannot be installed
without supporting unit like hard block.
26 7/16"
(671.7 mm)
24"
3"
A
Installation requirements
English 13
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 13Install_DOP30T940DS_DA_DG68-01457A_EN.indd 13 2022-10-11 오전 11:37:002022-10-11 오전 11:37:00
Page 14
Installation requirements
Recommended locations for gas piping and electrical outlets
Optional rear ller kit
WARNING
Used to ll gap between the range back and wall. Adds a ller strip to the rear
of the range. This kit can only be used when the opening in the countertop is 25”
deep.
NOTE
If the countertop depth is greater than 25”, there will be a gap between the ller
kit and the back wall.
Installation requirements
Recommended
position for
Electrical outlet
Recommended
position for Gas stub
B
A
Model DOP30**40D*
A
B
9 ⅞”(W) X 6 ⅞”(H) (25.1 cm x 17.5 cm)
15
/16" (W) X 5 3/8''(H) (45.5 cm x 13.8 cm)
17
Electrical outlet
Gas piping
CAUTION
You must use the rear ller kit to install the range in a freestanding cutout cabinet.
For more information, see “Optional rear ller kit” as shown below.
14 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 14Install_DOP30T940DS_DA_DG68-01457A_EN.indd 14 2022-10-11 오전 11:37:002022-10-11 오전 11:37:00
Page 15
To remove safely from the pallet
To avoid breakage
1. Remove the screws from the bottom
bracket on either side of the unit.
2. Press the bracket on either side to pull
out.
3. Have two persons hold both bottom
sides of the unit and lift up to remove
from the pallet. Use caution not to hold
the door handle.
CAUTION
• Please DO NOT push the unit strongly
when you install. These actions can
cause the damage to the unit.
• Hold the upper left/right area of the
door (not the door handle) with both
hands and push the unit in. Do not grab
the door handle or push the burner
knobs.
Installation requirements
English 15
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 15Install_DOP30T940DS_DA_DG68-01457A_EN.indd 15 2022-10-11 오전 11:37:012022-10-11 오전 11:37:01
Page 16
Installation requirements
CAUTION
Do NOT lift or handle the unit by the cooktop frame.
1. The counter top around the cut-out
should be at and leveled (See hatched
area on Fig. 1).
2. Before installing the unit, measure
the heights of the two cabinet sides
(C1~C4), front and back (See Fig. 1)
from the oor to the top of the counter.
3. Level the range using the four leveling
legs so that the height from the oor
to the underside of the cooktop frame
is greater than the tallest cabinet
measurement by at least 1/16”.
C2
Installation requirements
C1
C3
C4
Flg.1
4. Slide the unit into the cabinet (DO NOT
PUSH THE UNIT HARD). Make sure the
center of the unit aligns with the center
of the cabinet cut-out.
5. The metal ange under each side of
the cooktop MUST be placed over the
cabinet countertop for proper unit
support. The cooktop should NOT rest
directly on the countertop or else it
could cause damage to the cooktop
voiding the warranty. Level the unit if
needed.
Gas requirements
Provide adequate gas supply
This range is designed to operate at a pressure of 5 in (13 cm) of water column on
natural gas or 10 in (25 cm) of water column on LP gas (propane or butane).
Make sure you are supplying your range with the type of gas for which it is
designed.
Do not attempt to convert the appliance from the gas specied in this manual to a
different gas without consulting the gas supplier.
This range is convertible for use on natural or propane gas. If you decide to use
this range on LP gas, conversion must be made by a qualied LP installer before
attempting to operate the range.
For proper operation, the pressure of natural gas supplied to the regulator must be
between 5 in and 13 in (13 cm and 33 cm) of water column.
For LP gas, the pressure supplied must be between 10 in and 13 in (25 cm and
33 cm) of water column.
When checking for proper operation of the regulator, the inlet pressure must be at
least 1 in (2.5 cm) greater than the operating (manifold) pressure as given.
The pressure regulator located at the inlet of the range manifold must remain in
the supply line regardless of whether natural or LP gas is being used.
A exible-metal appliance connector used to connect the range to the gas supply
line should have an I.D. of 0.5 in (1.3 cm) and be 5 ft (152 cm) in length for ease of
installation. In Canada, exible connectors must be single-wall metal connectors no
longer than 6 ft (183 cm) in length.
Do not kink or damage the exible metal tubing when moving the range.
16 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 16Install_DOP30T940DS_DA_DG68-01457A_EN.indd 16 2022-10-11 오전 11:37:012022-10-11 오전 11:37:01
Page 17
Special gas requirements (gas models sold in Massachusetts)
Electrical requirements
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS:
WARNING
• Gas leaks may occur in your system, creating a dangerous situation.
- Gas leaks may not be detected by smell alone.
- Gas suppliers recommend you purchase and install a UL-approved
gas detector. Gas detector should be installed in accordance with the
manufacturers instructions.
• Range must be installed by a qualied plumber or gas tter by the State of
Massachusetts.
• A T-handle manual gas valve MUST be installed in the gas supply line to your
range.
• If a exible gas connector is used to install your range, multiple exible gas
lines must not be connected in series.
WARNING
To reduce the risk of re, electric shock, or personal injury:
All ranges
• Do not use an extension cord or adapter plug with this range.
• This range must be properly grounded.
• Check with a qualied electrician if you are in doubt as to whether your range
is properly grounded.
• Do not modify the plug provided with your range—if it doesn’t t the outlet,
have a proper outlet installed by a qualied electrician.
• All wiring and grounding must be done in accordance with local codes or, in
the absence of local codes, with the National Electrical Code, ANSI/NFPA No.
70 – Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 –
Latest Revisions and local codes and ordinances.
• Wiring diagram is located on the back of the range. (Inside of the cover back
wire)
• This range is equipped with an electronic ignition system that will not operate
if plugged into an outlet that is not properly polarized.
Dual fuel models
• Canada models are equipped with a power cord with an equipment-grounding
conductor and a grounding plug.
(The power cord is not provided in US model.)
• A 240-Volt, 60-Hz, AC, approved electrical service with 40-amp circuit breaker
or time-delay fuse is required for all U.S. and Canadian models.
• Check for ¾-in (1.9-cm) UL-listed strain relief where the power cord comes out
of the range cabinet.
• Do not reuse a power supply cord from an old range or other appliance.
• The power cord electric supply wiring must be retained at the range cabinet
with a suitable UL-listed strain relief.
• A time-delay fuse or circuit breaker is also recommended.
Installation requirements
English 17
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 17Install_DOP30T940DS_DA_DG68-01457A_EN.indd 17 2022-10-11 오전 11:37:012022-10-11 오전 11:37:01
Page 18
Installation requirements
Grounding
• All ranges must be grounded for personal safety.
• All gas models have a power cord with an equipment-grounding conductor
and a grounding plug.
• The plug must be rmly plugged into a 3-prong or 4-prong outlet that is
properly installed and grounded in accordance with all local codes and
ordinances. In the event of a malfunction or breakdown, grounding will
decrease the risk of electrical shock by providing a path for the electric
current.
• Do not use a damaged power plug or loose wall outlet.
• Do not use an extension cord or adapter with this appliance.
• Do not, under any circumstances, cut, modify, remove, or otherwise defeat the
grounding if quipped. If the plug and the outlet do not match or you have any
doubt, have a qualied electrician install the proper outlet.
The customer should have the wall receptacle and circuit checked by a
Installation requirements
qualied electrician to make sure the receptacle is properly grounded.
Ground Fault Circuit Interrupters(GFCIs) are not required or recommended for
range receptacles.
• NEVER connect ground wire to plastic plumbing lines, gas lines, or water
pipes.
CAUTION
Failure to follow these instructions can result in death, re, or electrical shock.
Usage situations where appliance power cord will be disconnected frequently
Do not use an adapter plug in these situations because disconnecting of the power
cord places under strain on the adapter and leads to eventual failure of the adapter
ground terminal. 240 V plug have 3 or 4 prongs and are not supplied with a unit.
Additional installation requirements for mobile homes
The installation of appliances designed for mobile home installation must conform
with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part
3280 (formerly the Federal Standard for Mobile Home Construction and Safety,
Title 24, HUD, Part 280) or, when such standard is not applicable, the Standard
for Manufactured Home Installations, latest edition (Manufactured Home Sites,
Communities and Set-Ups), ANSI A225.1, latest edition, or with local codes. In
Canada, mobile home installation must be in accordance with the current CAN/CSA
Z240/MH Mobile Home Installation Code.
18 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 18Install_DOP30T940DS_DA_DG68-01457A_EN.indd 18 2022-10-11 오전 11:37:012022-10-11 오전 11:37:01
Page 19
Tools and materials
What’s in the box
Parts supplied
Grates (2) Burner heads (4) and
Burner caps (4)
Flat rack (1) Convection lters (2) Temperature probe (1)
Gliding racks (2) Wok ring (1) Anti-tip bracket (1)
Brass burner caps(4)
NOTE
• Make sure you have received all of the supplied parts shown above.
• If your range was damaged during shipping or you do not have all of the
supplied parts, contact your local retailer.
Parts needed
4-wire cord or
3-wire cord
Flare union adapter
½" (NPT) x ½" (ID)
Tools needed
Flat-blade
screwdriver
Gas line
shut-off valve
135-degree elbow
Phillips
screwdriver
Flexible metal
appliance connector
½" (ID) x 5 ft
(optional)
Open-end or
adjustable wrench
Flare union adapter
¾" or ½" (NPT) x ½" (ID)
Lag bolt or ½" (OD)
sleeve anchor
Pipe wrench (2)
Tools and materials
Pencil and ruler Level
Air Fry tray (1)
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 19Install_DOP30T940DS_DA_DG68-01457A_EN.indd 19 2022-10-11 오전 11:37:032022-10-11 오전 11:37:03
Utility knife
Soapy water solution
Pipe joint compound
Nut driver
English 19
Page 20
Installation instructionsInstallation instructions
Installation instructions
Installing your Dual fuel Range
NOTE
• IMPORTANT: Please read the following instructions, as well as the Important
Safety Instructions section at the front of this manual, completely and
carefully BEFORE installing and/or operating the gas range. Improper
installation, adjustment, service, or maintenance can cause personal injury or
property damage.
• To order parts or accessories, contact
your local retailer or refer to the last
page.
• To ensure proper installation, we
strongly recommend that you hire a
professional installer.
Step 1. Unpack the range
Remove all packaging materials. Failure to remove packaging materials could
result in damage to the appliance.
Inventory all loose parts against the 'Parts supplied' overview on page 19.
Check for shipping damage and/or missing parts. Any damage and/or missing
parts should be reported to your local retailer.
Step 2. Meeting electrical connection requirements
CAUTION
For personal safety, do not use an extension cord with this appliance. Remove
house fuse or open circuit breaker before beginning installation.
This appliance must be supplied with the proper voltage and frequency, and
connected to an individual properly grounded branch circuit, protected by a circuit
breaker or fuse having amperage as specied on the rating plate. The rating plate
is located on the bottom side of the control panel.
We recommend you have the electrical wiring and hookup of your range
connected by a qualied electrician. After installation, have the electrician show
you where your main range disconnect is located.
Check with your local utilities for electrical codes which apply in your area. Failure
to wire your oven according to governing codes could result in a hazardous
condition.
If there are no local codes, your range must be wired and fused to meet the
requirements of the National Electrical Code, ANSI/NFPA No. 70–Latest Edition.
You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical Code requires that new
construction (not existing) utilize a 4-conductor connection to an electric range.
When installing an electric range in new construction, follow Steps 2 and 3 for
4-wire connection.
You must use a 3-wire or 4-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt,
60 hertz electrical system.
If the electrical service provided does not meet the above specications, have a
licensed electrician install an approved outlet.
Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be
provided with ring terminals on wire and a strain relief device.
A range cord rated at 40 amps with 125/250 minimum volt range is required.
20 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 20Install_DOP30T940DS_DA_DG68-01457A_EN.indd 20 2022-10-11 오전 11:37:032022-10-11 오전 11:37:03
Page 21
Strain relief
Power cord
Conduit connection
plate
A 50 amp range cord is not recommended but if used, it should be marked for
Access cover
Terminal block
use with nominal 1⅜" diameter connection openings. Care should be taken to
center the cable and strain relief within the knockout hole to keep the edge from
damaging the cable.
Because range terminals are not accessible after range is in position, exible
service conduit or cord must be used.
NOTE
If conduit is being used, go to Step 5 on pages 23–24.
ALL NEW BRANCH-CIRCUIT CONSTRUCTIONS, MOBILE HOMES,
RECREATIONAL VEHICLES AND INSTALLATIONS WHERE LOCAL
CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL, REQUIRE A
4-CONDUCTOR UL-LISTED RANGE CORD.
Step 3. Accessing the power cord connection
Remove the rear access cover and loosen the screw with a screwdriver. The
terminal block will then be accessible.
Specied power-supply-cord kit rating
Range rating, watts
120/240
volts 3-wire
120/208
volts 3-wire
Specied rating
of power-supplycord kit, amperes
Diameter (inches) of range
connection opening
Power cord Conduit
8750 - 16500 7801 - 12500 40 or 50 A 1⅜" 1⅛"
Step 4. Installing the power cord
For power cord installations, hook the strain relief over the power cord hole (1⅜")
located below the rear of the drawer body. Insert the power cord through the
strain relief and tighten the device.
• You must install the power cord with a strain relief.
• Attach the strain relief to the 1⅜" opening in conduit connection plate.
Installation instructions
English 21
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 21Install_DOP30T940DS_DA_DG68-01457A_EN.indd 21 2022-10-11 오전 11:37:032022-10-11 오전 11:37:03
Page 22
Installation instructions
Ground strap
Ground plate
Ground
screw
Neutral
terminal
Ground wire
(Green)
White
Black
Red
Black
White
Red
Ground strap
Neutral
terminal
Black
White
Red
Black
White
Red
Installation instructions
Installing a 3-wire power cord
WARNING
The neutral or ground wire of the power cord must be connected to the neutral
terminal located in the center of the terminal block. The power leads must be
connected to the lower left and the lower right terminals of the terminal block.
1. Remove the 3 lower terminal screws
from the terminal block.
2. Insert the 3 terminal screws through
each power cord terminal ring and into
the lower terminals of the terminal
block. Be certain that the center wire
(white/neutral) is connected to the
center lower position of the terminal
block.
3. Tighten screws securely into the
terminal block. DO NOT remove the
ground strap connection.
4. Go to Step 6 on page 24 and proceed
with the installation.
Installing a 4-wire power cord
WARNING
The neutral wire of the supply circuit must be connected to the neutral terminal
located in the lower center of the terminal block. The power leads must be
connected to the lower left and the lower right terminals of the terminal block. The
4th grounding lead must be connected to the frame of the range with the ground
plate and the ground screw.
1. Remove the 3 lower terminal screws
from the terminal block. Remove the
ground screw and ground plate and
retain them.
2. Cut and discard the ground strap. Do
not discard any screws.
3. Insert the one ground screw into the
power cord ground wire terminal ring,
through the ground plate, and into the
frame of the range.
4. Insert the 3 terminal screws (removed
earlier) through each power cord
terminal ring and into the lower
terminals of the terminal block. Be
certain that the center wire (white/
neutral) is connected to the center
lower position of the terminal block.
Tighten screws securely into the
terminal block.
5. Go to Step 6 on page 24 and proceed
with the installation.
22 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 22Install_DOP30T940DS_DA_DG68-01457A_EN.indd 22 2022-10-11 오전 11:37:042022-10-11 오전 11:37:04
Page 23
White
Black
Red
Ground
strap
Neutral
terminal
Wire tips
Red
White
Black
Step 5. Installing the conduit
1⅛" 1⅜"
1⅛"1⅜"
Conduit connection plate
Strain relief
Ring
Body
Figure 2Figure 2
1"
3½"
⅜" 1"
3½"
3 wire3 wire 4 wire4 wire
Knockout surface
Figure 1Figure 1
⅜"
Remove the conduit connection plate from the rear of the drawer body and rotate
it as shown below.
The conduit hole (1⅛") must be used.
1. Prepare the conduit cord shown in Figure 1.
2. Install the conduit cord as shown in Figure 2.
Installing a 3-wire conduit
• Aluminum building wire may be used but it must be rated for the correct
amperage and voltage to make the connection. Connect wires according to
Step 4 depending on the number of wires.
• Wire used, location and enclosure of splices, etc., must conform to good wiring
practices and local codes.
1. Loosen the 3 lower terminal screws
from the terminal block.
2. Insert the center bare wire (white/
neutral) tip through the bottom center
terminal block opening. On certain
models, the wire will need to be
inserted through the ground strap
opening and then into the bottom
center block opening.
3. Insert the two side bare wire tips into
the lower left and the lower right
terminal block openings.
4. Tighten the screws until the wire is
rmly secured (35 to 50 inch-lbs.). Do
not over-tighten the screws since it
could damage the wires.
5. Go to Step 6 on page 24 and proceed
with the installation.
Installation instructions
For conduit installations, insert the strain relief (not included) into the conduit hole
(1⅛"). Then thread the conduit cord through the body of the strain relief and fasten
the ring. Reinstall the bracket.
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 23Install_DOP30T940DS_DA_DG68-01457A_EN.indd 23 2022-10-11 오전 11:37:042022-10-11 오전 11:37:04
English 23
Page 24
Installation instructions
Ground strap
Ground plate
White
Black
Red
Neutral
terminal
Ground wire
(Green)
Wire
tips
White
Black
Red
Installation instructions
Installing a 4-wire conduit
• Aluminum building wire may be used but it must be rated for the correct
amperage and voltage to make the connection. Connect wires according to this
Step 4 depending on the number of wires.
• Wire used, location and enclosure of splices, etc., must conform to good wiring
practices and local codes.
1. Loosen the 3 lower terminal screws
from the terminal block. Remove the
ground screw and ground plate and
retain them.
2. Cut and discard the ground strap. Do
not discard any screws.
3. Insert the ground bare wire tip between
the range frame and the ground plate
(removed earlier) and secure it in
place with the ground screw (removed
earlier).
4. Insert the bare wire (white/neutral)
tip through the bottom center of the
terminal block opening.
5. Insert the two side bare wire tips into
the lower left and the lower right
terminal block openings.
6. Tighten the screws until the wire is
rmly secured (35 to 50 inch-lbs.). Do
not over-tighten the screws since it
could damage the wires.
7. Go to Step 6 and proceed with the
installation.
Step 6. Replacing the access cover
Replace the access cover on the range back. To replace the wire cover, insert
double projections in the pockets located below the opening and tighten the screw.
24 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 24Install_DOP30T940DS_DA_DG68-01457A_EN.indd 24 2022-10-11 오전 11:37:052022-10-11 오전 11:37:05
Page 25
Step 7. Connect the range to gas supply
Shut off the main gas supply valve before disconnecting the old range and leave
it off until the new hookup has been completed. Don’t forget to relight the pilot on
other gas appliances when you turn the gas back on.
Because hard piping restricts movement of the range, the use of a CSA
International-certied exible metal appliance connector is recommended unless
local codes require a hard-piped connection.
WARNING
If the information in this manual is not followed exactly, a re or explosion may
result, causing death, personal injury, or property damage.
• Do not store or use gasoline or other ammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
- DO NOT light a match, candle, or cigarette.
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch.
- DO NOT use any phone in your building.
- Clear the room, building, or area of all occupants.
- Immediately call your gas supplier from a neighbor’s phone. Follow the
gas supplier’s instructions.
- If you cannot reach your gas supplier, call the re department.
• Installation and service must be performed by a qualied installer, service
agency, or gas supplier.
Never use an old connector when installing a new range. If the hard-piping method
is used, you must carefully align the pipe; the range cannot be moved after the
connection is made.
To prevent gas leaks, apply pipe-joint compound or wrap pipe-thread tape with
Teon on all male (external) pipe threads.
1. Install a manual gas line shut-off valve in the gas line in an easily accessed
location outside of the range.
Make sure everyone operating the range knows where and how to shut off
the gas supply to the range.
2. Install male 0.5-in (1.3-cm) are union adapter to the 0.5-in (1.3-cm) NPT
internal thread at the regulator inlet. Use a backup wrench on the regulator
tting to avoid damage.
When installing the range from the front, remove the 90 ° elbow for easier
installation.
3. Install male 0.5-in (1.3-cm) or 0.75-in (1.9-cm) are union adapter to the NPT
internal thread of the manual shut-off valve, taking care to back up the shutoff valve to keep it from turning.
4. Connect exible metal appliance connector to the adapter on the range.
Position range to permit connection at the shut-off valve.
5. When all connections have been made, make sure all range controls are in the
off position and turn on the main gas supply valve. Use a liquid leak detector
at all joints and connections to check for leaks in the system.
WARNING
To prevent death, personal injury, explosion, and/or re hazard, DO NOT use a
ame to check for gas leaks.
When using test pressures greater than ½ psig to pressure-test the gas supply
system of the residence, disconnect the range and individual shut-off valve from
the gas supply piping. When using test pressures of ½ psig or less to test the gas
supply system, simply isolate the range from the gas supply system by closing the
individual shut-off valve.
Installation instructions
English 25
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 25Install_DOP30T940DS_DA_DG68-01457A_EN.indd 25 2022-10-11 오전 11:37:052022-10-11 오전 11:37:05
Page 26
Installation instructions
Installation instructions
WARNING
Do not exceed 25 ft-lbs of torque when making gas line connections.
Overtightening may crack the pressure regulator resulting in gas leak.
Flexible connector hookup
Installer: Inform the consumer of the location of the gas shut-off valve.
Gas Shut-Off Valve
0.5 in or 0.75 in Gas Pipe
Adapter
Tubing Line to Cooktop
Control Manifold
Flex Connector
(6-ft max.)
Gas Flow into Range
Adapter
NOTE
• If your area requires a rigid pipe hookup, contact a qualied installer, service
agency, or gas supplier.
• The gas shut-off valve should be installed in an accessible location in the gas
piping, external to the appliance, for the purpose of turning on or shutting off
the gas to the appliance.
Pressure
Regulator
Step 8. Convert to lp gas (optional)
All new ranges are shipped from the factory set up to use natural gas.
This Dacor range can be converted to use LP gas.
(Contact a qualied service technician.)
The conversion process should only be performed by a qualied LP gas installer.
Conversion instructions and LP orices will be supplied with the LP conversion kit.
The conversion to LP requires all burner orices to be changed (4 surface burners).
In addition, the nozzle on the gas pressure regulator needs to be reversed. All
replaced orices must be left with the consumer, including the instructions and
retrot sizes and orice indication.
Checking the ame quality all burner after converting to LP gas.
Step 9. Install the anti-tip device
WARNING
• To reduce the risk of tipping, the appliance must be secured by properly
installing the anti-tip device packed with the appliance.
• All ranges can tip, resulting in personal injury.
• Tipping ranges can cause burns from spills, personal injury, and/or death.
• To prevent accidental tipping, install and check the anti-tip bracket following
the instructions and template supplied with the bracket.
An anti-tip bracket and screws, installation
instructions, and template are shipped
with every range (PN DG94-00870B). The
instructions include information necessary
to complete the installation of the anti-tip
bracket. Read and follow the instructions on
the sheet and use the template for anti-tip
bracket installation. If not properly installed,
the range could be tipped by you or a child
standing, sitting, or leaning on an open oven
door.
26 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 26Install_DOP30T940DS_DA_DG68-01457A_EN.indd 26 2022-10-11 오전 11:37:052022-10-11 오전 11:37:05
Page 27
*approximately
21
/32” (16.5 mm)
Anti-Tip
bracket
Screw must enter wood or concrete
NOTE
To install the Anti-tip bracket, release the leveling leg using pipe wrench because
Loctite is applied on Bolt for vibration unlocking. A minimum clearance of
21
/32”
(16.5 mm) is required between the range bottom and the kitchen oor.
To check if the bracket is installed and engaged properly, remove storage drawer
and look underneath the range to see that the leveling leg is engaged in the
bracket. Carefully tip the range forward. The bracket should stop the range within
4 inches (10.2 cm) of tipping. If it does not, the bracket must be reinstalled.
If the range is pulled from the wall for any reason, always repeat this procedure
to verify the range is properly secured by the anti-tip bracket. Never completely
remove the leveling legs or the range will not be secured to the anti-tip device
properly.
Step 10. Plug in and place
WARNING
• BEFORE OPERATING OR TESTING, follow the grounding requirements on pages
17–18 in this manual. Improper connection of the grounding plug can result in
a risk of electric shock.
Please review "Electrical requirements" on pages 17–18.
• Altering any part of this system may result in a short or overload.
1. Plug in the power cord. Make sure the outlet meets local or national electrical
codes as referenced on pages 17–18.
2. Slide the range into place.
3. Check the gas supply line to make sure it did not get damaged and it stayed
connected during positioning.
4. Check to make sure the back leg of the range has slid into the anti-tip bracket.
Carefully tip the range forward
to ensure that the anti-tip bracket engages the
back brace and prevents tip-over.
Installation instructions
English 27
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 27Install_DOP30T940DS_DA_DG68-01457A_EN.indd 27 2022-10-11 오전 11:37:052022-10-11 오전 11:37:05
Page 28
Installation instructions
Installation instructions
Step 11. Moving and placing the range
1. Due to the weight, heavy equipment
movers such as Air Sled should be used
to move this unit. The weight must be
supported uniformly across the bottom.
2. After transporting the range by Air
Sled where you want, the range can
be leveled by adjusting the legs with
a wrench while Air Sled is supported.
Using a wrench, level the range by
turning the front leveling legs in or
out as necessary. Counterclockwise
Air Sled Insert
NOTE
Adjust the leveling legs only as far as necessary to level the range. Extending the
leveling legs more than necessary or removing legs can cause the range to be
unstable.
shortens the leg and lowers the range.
Clockwise lengthens the leg and raises
the range.
3. If range is next to or between cabinets,
make sure the cooktop (without the
surface burner grates) is level with the
countertops.
4. Position an oven rack in the center rack
position.
5. Check the level of the range with a
carpenter level using the two positions
shown at right.
6. After the range becomes level, Use Air
Sled to move the range away from the
wall so that the anti-tip bracket can be
installed.
7. After installing and leveling the range,
carefully remove Air Sled and install
front leg covers (right and left).
28 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 28Install_DOP30T940DS_DA_DG68-01457A_EN.indd 28 2022-10-11 오전 11:37:052022-10-11 오전 11:37:05
Page 29
Step 12. Assemble the surface burners
CAUTION
Do not operate the surface burners without all burner parts in place.
1. Position surface burner heads on top of the surface burner manifolds. The
electrodes will t into the slot in the bottom of the heads. Make sure the
surface burner heads are at and parallel with the cooktop.
2. Place the matching size caps on top of each surface burner head.
Top Bottom
3. Place the left and right surface burner
grates on the cooktop. The edges of the
grates should match up with the edges
of the cooktop.
NOTE
• Grates should be placed on its own
position.
• You can recognize the right position of
the grates by checking the bottom side
of each. Look for engraved position on
right and left grate, “RIGHT REAR” and
“LEFT REAR” respectively.
• The grates are heavy. Be careful while
handling the grates.
Step 13. Check the ignition of surface burners
Check the operation of all cooktop burners after the range has been installed and
assembled, gas supply lines have been carefully checked for leaks, and electrical
power cord has been plugged in.
All surface burners have electronic ignition.
To turn on a surface burner:
1. Push in the control knob, and then
turn it to the LITE position. You will
hear a "clicking" sound indicating the
electronic ignition system is working
properly. The burner will light in about
4 seconds, after the air has been
purged from the supply line.
2. After the burner lights, turn the control
knob to the desired setting. The
"clicking" sound will stop and the ame
height will change from Max. to Min.
during turning the control knob.
3. Repeat steps 1 and 2 to check the
operation of each surface burner in
succession.
Installation instructions
English 29
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 29Install_DOP30T940DS_DA_DG68-01457A_EN.indd 29 2022-10-11 오전 11:37:062022-10-11 오전 11:37:06
Page 30
Installation instructions
Installation instructions
Checking the ame quality:
All combustion ames need to be visually checked to determine their ame
quality.
1. Prevailing soft blue ames—Normal for
natural gas operation.
2. Yellow tips on outer cones—Normal for
LP gas operation.
3. Yellow ames—Abnormal for any gas
operation; call for service.
NOTE
If burner ame looks like 3, the range
should not be used until it is serviced. Call
Dacor for service. Normal burner ames
shall look like 1 or 2, depending on the gas
type you use.
Step 14. Final installation checklist
You have just completed installing your range. Make sure all controls are in the
OFF position and the ow of ventilation air to the range is unobstructed. The
following is a checklist to conrm your range is safely installed and ready for
operation.
• Gas line has been properly connected to the range. The gas has been turned
on. All connections have been checked for leaks.
• Range is plugged into the properly grounded electrical receptacle.
• Approved anti-tip bracket is properly installed and engaged with the range.
• Range is leveled and is rmly sitting on a solid, level oor.
• All burners have been tested for proper operation.
To adjust ame low setting
Identify which burner is exhibiting too high or too low simmer ame size, adjust
as necessary by following steps below:
1. Rotate a knob to "LO" position and
remove the knob from the valve shaft
while the ame is lit.
Simmer Set
Screw
Small
Screwdriver
Valve Stem
WARNING
1. Do not completely remove the valve set screw from the valve stem. The valve
set screw is an integral part of the gas valve assembly. Removing the valve
set screw will cause gas to leak.
2. After adjusting the valve set screw, inspect the assembly for gas leaks.
2. Carefully push the screw driver into
the stem of the valve, until it hits
the simmer set screw. Make sure the
screwdriver athead is seated into the
set screw groove.
3. Rotate valve set screw clockwise to
decrease "LO" setting ame output, or
rotate set screw counter clockwise to
increase "LO" setting ame output.
30 English
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 30Install_DOP30T940DS_DA_DG68-01457A_EN.indd 30 2022-10-11 오전 11:37:062022-10-11 오전 11:37:06
Page 31
Please visit www.Dacor.com to activate your warranty online.
WARRANTY INFORMATION
cut herecut here
IMPORTANT:
Your warranty will not begin until you activate it online or return this form to
Dacor. If you have purchased more than one Dacor product, please return all forms
in one envelope, or activate the warranty for each product online.
Please rest assured that under no conditions will Dacor sell your name or any of the
information on this form for mailing list purposes. We are very grateful that you
have chosen Dacor products for your home and we do not consider the sale of such
information to be a proper way of expressing our gratitude!
Owner’s Name:
Street:
City: State:
Zip:
Purchase Date: Email:
Telephone:
Dealer:
City: State:
Zip:
Your willingness to take a few seconds to ll in the section below will be sincerely
appreciated. Thank you.
1. How were you rst exposed to Dacor products? (Please check one only.)
2. Where did you buy your Dacor appliances?
Last (Please Print or Type) First Middle
A. T.V. Cooking Show F. Builder
B. Magazine G. Architect/Designer
C. Appliance Dealer Showroom H. Another Dacor Owner
D. Kitchen Dealer Showroom I. Model Home
E. Home Show J. Other
A. Appliance Dealer D. Builder
B. Kitchen Dealer E. Other
C. Builder Supplier
3. For what purpose was the product purchased?
A. Replacement
B. Part of a Remodel D. Other
4. What is your household income?
A. Under $75,000 D. $150,000 – $200,000
B. $75,000 – $100,000 E. $200,000 – $250,000
C. $100,000 – $150,000 F. Over $250,000
5. What are the brands of appliances that you have in your kitchen?
A. Cooktop C. Dishwasher
B. Oven D. Refrigerator
6. Would you buy or recommend another Dacor product?
Yes No
Comments:
Thank you very much for your
assistance. The information you have
provided will be extremely valuable
in helping us plan for the future and
giving you the support you deserve.
Website: www.Dacor.com
Phone: 833-35-ELITE (833-353-5483)
only
Place Serial Number Label Here
C. New Home
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 31Install_DOP30T940DS_DA_DG68-01457A_EN.indd 31 2022-10-11 오전 11:37:062022-10-11 오전 11:37:06
Page 32
DG68-01457A-00
∙ Phone: 833-35-ELITE (833-353-5483) ∙ Fax: (626) 403-3130 ∙ www.dacor.com
Install_DOP30T940DS_DA_DG68-01457A_EN.indd 32Install_DOP30T940DS_DA_DG68-01457A_EN.indd 32 2022-10-11 오전 11:37:062022-10-11 오전 11:37:06
Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745
Loading...