Dacor DOB30M977DS, DOB30M977DM, DOB30M977SM, DOB30M977SS Installation Manual

Installation Instructions

Modernist Built-In Electric Wall Oven

DOB30M977**

Part No. 112174 Rev A

Contents

Contents

Before you begin... 3

Important 3

Customer-service information 4

If You Need Help... 4

Important safety instructions 5

Related equipment safety 5
Transport 5

Installation requirements 8

Checklist 8
Prepare to install the oven 9
Location requirements 10
Single ovens 11
Double ovens 18

Installation instructions 25

Prepare built-in oven 25
Remove and replace oven door(s) 26
Electrical connection 30
Install oven 34
Self-diagnosis 36

English2

Before you begin...

Important

Overall design/accessories may differ
with the model.

Installer

• For safety and to minimize problems,

read this manual thoroughly before
starting the installation.

• Leave this manual with the user.

• Write the oven’s model/serial

numbers in this manual for service/

maintenance reference.

User

• Keep this manual for personal reference
and for that of inspectors, service
personnel, etc.

Before you begin...

English 3

Customer-service information

If You Need Help...

If you have questions or problems with installation, contact your Dacor® dealer or the
Dacor Customer-Service team. If your Dacor appliance is under warranty, call Dacor
Distinctive Service. Have the appliance’s model/serial numbers available when you call.

Dacor Modernist Service (repairs under warranty only)

Phone: [phone] ex. 2822 (U.S.A. and Canada)
Monday — Friday 6:00 a.m. to 4:00 p.m. Pacific Time

Dacor Customer Service

Phone: [phone] ex. 2813 (U.S.A. and Canada)

Customer-service information

Monday — Friday 6:00 a.m. to 5:00 p.m. Pacific Time
Web site: www.dacor.com

All specifications are subject to change without notice. Dacor assumes no liability for
changes to specifications.

© 2017 Dacor, all rights reserved.

English4

Important safety instructions

Related equipment safety

Remove all tape and packaging before using the appliance. Dispose of the packaging
after unpacking the appliance. Never let children play with packaging material.
Never modify the oven (e.g., do not remove panels, wire covers,

Transport

To avoid damage to the oven vent, use the transport method shown in the picture below.

Support the bottom of the oven from
either side when moving it to the

A

B

installation site. Leave the unit attached
to the pallet until it is in front of the
cabinet opening and ready to be lifted
into place.

or screws).

Important safety instructions

A. Front
B. Pallet

D

ANGER

ELECTRICAL SHOCK HAZARD

To avoid risk of electrical shock, personal injury, or death; verify your appliance is
grounded according to local codes or in their absence, with the National Electrical Code
(NEC). ANSI/NFPA 70-latest edition.

WARNING

MOVING HAZARD

To avoid risk of severe personal injury; this appliance requires two or more people while
handling and moving. Use of appliance moving devices is recommended.

English 5

Important safety instructions

WARNING

• The information in this manual should be followed exactly to avoid fire or electrical

shock that may cause property damage, personal injury, or death.

• Save this manual for local electrical inspector’s use.

• Ensure your appliance is properly installed and grounded by a qualified technician.

• New branch-circuit installations (1996 NEC), mobile homes, RVs, or installations

where local codes prohibit grounding through the neutral conductor require 4-wire
branch-circuit connection.

• Improper connection of aluminum house wiring to copper leads can cause an

electrical hazard or fire. Use only connectors designed for joining copper to
aluminum and follow the manufacturer’s recommended procedure closely.

• Mounting screws must be used. Failure to do so can result in the oven falling out of

the cabinet causing serious injury.

Important safety instructions

CAUTION

• The cabinets and wall coverings around the oven must be able to withstand the heat

(up to 194 °F [90 °C]) generated by the oven; otherwise, discoloration, delamination,
or melting may occur.

• DO NOT remove spacers on the side walls of the built-in oven. The spacers center the

oven in the space provided. The oven must be centered to prevent excess heat
buildup that may result in heat damage or fire.

English6

WARNING

Follow the information in this manual exactly; otherwise, fire or electrical shock may
result causing property damage, personal injury, or death.

IMPORTANT NOTE

The installer shall ensure proper installation. Product failure due to improper i
NOT covered under warranty.

WARNING

nstallation is

DO NOT put weight on the oven door. Never let anyone to climb, sit, stand, or hang on
the oven door. The oven could tip, causing personal injury and property damage.

WARNING

Electricity must be off while the electrical connections are made. Failure to do so can
result in severe personal injury or death.

IMPORTANT NOTE

• Observe all governing ordinances.

• The oven must be properly grounded.

• Do not block oven vents (bottom-front of the oven) or leave combustible or heat-

sensitive items in front of them.

Important safety instructions

English 7

Installation requirements

Checklist

Use this checklist to verify that you have completed each step of the installation process:

1. Before installing the oven, verify the cabinet dimensions are correct and the
required electrical connections are present.

2. See this manual's content regardi
Packaging, Electrical Installation, Testing th

3. To lift the oven, hang the install handle onto the side hook of the unit.

4. Move the oven unit into place in front of the cabinet opening, leaving the bottom
packaging on the unit to avoid damaging flooring.

5. Team-lift the unit directly into the cabinet cutout, avoiding personal injury.

6. Ensure the electrical conduit reaches to the connection point properly.

7. Slide the unit fully into place, while routing the electrical conduit correctly.

8. With a Phillips screwdriver and supplied screws, anchor the oven to the cabinetry
opening.

9. Consult the complete installation instructions, and follow the other procedures
listed, including verifying proper oven function.

10. All product literature and accessories are supplied (may be wrapped or boxed)
with the oven.

ng Safety, Cabinet Dimensions, Removing

e Installation and Customer Service.

Installation requirements

English8

Prepare to install the oven

Phillips Screwdriver Drill

Prepare to install the oven

6 screws (M4 L16)

6 Wood Screws For Mounting (4 needed

for installation and 2 extra’s)

Materials needed

Junction Box Wire Nuts

3

/4” Conduit Connector Install Handle (only for double oven)

Installation requirements

English 9

Installation requirements

Location requirements

IMPORTANT: Observe all governing ordinances.

• Specified cabinet-opening dimensions are minimums and must be used.

• The cabinet recess must completely enclose all but the face of the oven.

• A grounded electrical supply is required. (See Electrical Requirements.)

• Put the electrical-supply junction box at most 3” (7.6 cm) below the support platform

within the cabinet. A 1” (2.5 cm) min. diameter hole should be drilled in the right/left
rear corner of the support platform for oven-cable access to the junction box.

NOTE

For under-counter installation, the junction box should be in the adjacent right/left
cabinet. For rear-wall installation, the junction box should be recessed in the upper­right corner of the cutout.

• The support platform must be solid, level, and flush with bottom of the cabinet cutout.

• Single oven: The floor must support 221 lb (100 Kg).

• Install the oven at least 12” (30 cm) from other appliances.

IMPORTANT: To avoid cabinet damage, check with your builder or cabinet supplier to
ensure the materials used will not discolor, delaminate, or sustain other damage. This
oven complies with the requirements of UL and CSA International, and the maximum

Installation requirements

allowable wood-cabinet temperatures of 194 °F (90 °C).

English10

Single ovens

Product dimensions

B

F

H

A

G

C

E

D-1

D-2

DIMENSION

A 28

4

/5” (73.1 cm) Overall height

(Recessed height in Flush installation)

B 28

1

/2” (72.4 cm) Recessed width

C 27⁄” (69.1 cm) Recessed height
D-1 23⁄” (58.7 cm) Recessed depth _Standard installation
D-2 24

E 29

F 47

2

/5” (62.0 cm) Recessed depth _Flush installation

3

/4” (75.6 cm) Door width

1

/4” (120 cm) Conduit length

G 30” (76.2 cm) Overall width (Handle width)
H 2⁄” (5.6 cm) Handle depth

Installation requirements

English 11

Installation requirements

Standard cabinet dimensions

Under counter

01 Gas or Electric cooktops may be installed over this oven. See cooktop installation

instructions for cutout size. See label on top of approved cooktop models.

02 Gas and Electrical Connections for Gas Cooktop Must be Located in an Adjacent

Accessible Location to the Right.

Cabinet DIMENSION

A Min.

Installation requirements

B Min. 1
C 4” (10.1 cm)
D Min. 28⁄” / Max. 28⁄” (Min. 72.4 cm / Max. 72.7 cm)
E Min. 1” / Max. 1⁄” (Min. 2.5 cm / Max. 3.2 cm)
F Min. 27⁄” / Max. 27⁄” ( Min. 69.2 cm / Max. 69.5 cm)
G 24” (61 cm)
H Min 22” (Min 55.9 cm)

I Max. 9

J 36” (91.4 cm) Counter top Height

K 25” (63.5 cm)

01

K

B

F

A

D

E

11

/16” (1.75 cm) – Overlap of Over Side Edges of Cutout

G

1

/2” (Max. 24.1 cm) – Junction Box

I

A

3

/8 (3.5 cm)

02

H

C

J

English12