Dacor DMR30M977WM Installation manual
Microwave In-A-Drawer
Flush Mount Installation Instructions
™
Model DMR24M977W
Table of Contents
Important Safety Instructions ..........................2
What You Need to Know
About Safety ............................................ 2
Safety Symbols and Labels .........................2
Installation Requirements ................................3
Important Notes To The Installer .................3
Important Notes To The Consumer ............... 3
Grounding Instructions ............................... 3
For Use With:
DMR24M977WM/DMR24M977WS
DMR30M977WM/DMR24M977WS
24" Flush Mount Installation Instructions ........4-5
30" Flush Mount Installation Instructions ........6-7
Information You Need To Know ......................... 8
Model and Serial Number Location ...............8
Care, Cleaning and Maintenance .................. 8
Before You Call for Service .......................... 8
Part No. 115213 Rev B
TINSKB223MRR0
Important Safety Instructions
WARNING
• If the information in this manual is not followed exactly, a re or electrical shock may result that could cause
property damage, personal injury or death.
• To reduce the risk of tipping, the Microwave In-A-Drawer™ must be secured by a properly installed anti-tip block.
• This drawer must be electrically grounded in accordance with local codes.
• Make sure the wall coverings and the cabinets around the drawer can withstand the heat generated by the
microwave.
• Never leave children alone or unattended in the area where a microwave is in use. Never leave the
drawer open when the microwave is unattended.
• Stepping, leaning or sitting on the drawer may result in serious injuries and can also cause damage to the
Microwave In-A-Drawer™.
• Do not use the drawer as a storage space. Doing so creates a potentially hazardous situation.
• Check that the time-of-day is on the display. If not, touch S T O P/CLEAR to prevent unintended use.
WHAT YOU NEED TO KNOW ABOUT
SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions appearing in
this guide are not meant to cover all possible conditions
and situations that may occur. Always use common
sense, caution and care when installing, maintaining or
operating this appliance.
Always contact Dacor® about problems or conditions you
do not understand.
SAFETY SYMBOLS AND LABELS
DANGER
Immediate hazards that WILL result in severe
personal injury or death.
WARNING
Hazards or unsafe practices that COULD result in
severe personal injury or death.
Installer: Leave these instructions with the appliance.
Customer: Please read and keep these installation
instructions for future reference. This guide provides
proper installation information.
If you have any questions, call:
Dacor Customer Service
1-800-793-0093 (U.S.A. and Canada)
Monday — Friday 6:00 am to 5:00 pm Pacic Time
Web site: www.Dacor.com
Have the complete model and serial number identication
of your appliance ready. These numbers are found on a
rating label, located on the faceplate behind the drawer
front. See page 6.
CAUTION
Hazards or unsafe practices that COULD result in
minor personal injury or property damage.
E2
HeadingInstallation Requirements
The importance of the proper installation of your new
appliance cannot be overemphasized. Installation should
be done by a qualied installer.
GROUNDING INSTRUCTIONS
Before you begin the installation process, read this entire
installation instruction manual. It contains information
necessary for proper, safe installation.
Any questions or problems with the installation should
be directed to your Dacor dealer or the Dacor Customer
Service Department at 800.793.0093. You can also visit
our web site at www.Dacor.com.
IMPORTANT NOTES TO THE
INSTALLER
• Read all of the installation instructions before
installing the Microwave In-A-Drawer™.
• Remove all packing material before connecting
the electrical supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the
consumer.
WARNING
Improper use of the grounding plug can result in a
risk of electric shock.
This appliance is equipped with a three-prong grounding
plug for your protection against possible electric
shock hazards. It must be plugged into a grounded
wall receptacle. If only a two-prong wall receptacle
is available, it is the responsibility of the customer to
have it replaced with a properly grounded three-prong
wall receptacle. Do not under any circumstances,
cut or remove the third (ground) prong from the
power cord. Do not use an adapter plug. Do not use
an extension cord. If the power supply cord is too short,
have a qualied electrician or serviceman install an outlet
near the appliance. Do not use a Ground Fault Circuit
Interrupter.
Power supply cord with
three-prong grounding plug
IMPORTANT NOTES TO THE
CONSUMER
Keep these instructions with your use & care manual for
future reference.
• When using any microwave oven generating
heat, there are certain safety precautions you
should follow, that are listed in the use & care
manual. Read the use and care manual and follow
all safety precautions carefully.
• Be sure your Microwave In-A-Drawer™ is installed
and grounded properly by a qualied installer or
service technician.
For SAFETY CONSIDERATIONS do not install the drawer
in any combustible cabinetry, which is not in accord with
the stated clearances and dimensions on pages 3, 4 and
5. See Figure 2 (for 24") or Figures 4 and 5 (for 30").
Grounding type wall receptacle
(ground fault circuit not allowed)
E3
Parts include:
A
I
back
from the face of the cabinet [pushing the face of the drawer out
/4" (6.35 mm)].
Heading24" Flush Mount Installation Instructions
Qty. Part
1
2
Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.
1.
Figure 1
B
D
F
G
K
L
J
M
C
E
H
Note: the face of the shelf must
3
sit 1
/4" (44.45 mm) back from
the face of the cabinet.
N
shelf face
O
cabinet face
DMR24M977WM/S
PREF-B019MRP0
Flush Mount Deector Vent
Stainless Steel
LX-CZB055MRE0
Mounting screws
A. 6" (152.40 mm)
B. Suggested electrical outlet location
C. Anti-Tip block
D. 5" (127 mm)
1
E. 3
/2" (88.90 mm)
F. 4" (101.60 mm)
3
G. 24
/16" (614.35 mm) minimum
1
24
/2" (622.3 mm) maximum
13
H. 14
I. 1
J. 23
K. 22
L. 1
M. 16
N. Floor must support 100 lb (45.4 kg)
O. 1
/16" (376.24 mm) to
bottom of Anti-Tip block
1
/16" (26.97 mm)
1
/2" (596.90 mm)
minimum depth
1
/8" (561.97 mm)
3
/4" (44.45 mm)
7
/8" (428.62 mm) opening
3
/4" (44.45 mm)
Anti-Tip block
Mounting cleat
Drawer face
A
C
L
Top view
Note: the mounting surface of the finished cleat must sit 1
B
Cabinet
C
face
1
/16" (26.97 mm)
1
A. 22" (558.8 mm) mounting cleat
opening width
1
B.
/4" (6.35 mm)
1
C. 1
/16" (26.97 mm)
Figure 2A
E4
Shelf detail showing the deflector vent installed.
Shelf detail showing the deflector vent during installation.
Position deflector vent and mark holes. Pre drill using a
bit before mounting.
Front view
Suggested electrical
outlet location
Anti-Tip block
Side view
Move oven location
downward for extended
countertops for better
viewing angle.
Anti-Tip
Figure 2B
No oven
A
B
C
A. 22 1/8" (561.97 mm) mounting
cleat opening width
3
B. 24
/16" (614.35 mm) minimum
1
24
/2" (622.3 mm) maximum
ush opening width
3
C.
/4" (19.05 mm) shelf
Heading24" Flush Mount Installation Instructions
3. Place the drawer adjacent to the wall or cabinet
opening. Plug the power supply cord into the electrical
outlet.
4. Carefully guide the drawer into the prepared opening.
Avoid contact with the sides of the cutout opening and
also pinching the cord between the oven and the wall.
5. Slide the drawer all the way back until the mounting
anges touch the cleats mounted in the cabinet
opening.
6. Open the drawer. Using the 4 holes on the drawer as a
template, pre drill the cabinet using a 1/16” (1.57 mm)
bit. See Figure 4.
Figure 2C
2. Install deector as shown in Figure 3A.
Figure 3A
7
16
/8"
(428.62 mm)
flush opening
height
Front face of cabinet
3
/4" (19.05 mm)
3
1
/4" (44.45 mm)
front face of shelf
1
/16" (1.57 mm)
shelf
block
Figure 4
Mounting
flange
7. Secure the drawer with the 4 screws supplied.
Figure 3B
E5
Loading...