Dacia Sandero 2011 User Manual

SANDERO

DRIVER’S HANDBOOK

RENAULT recommends ELF

ELF has developed a complete range of lubricants for RENAULT:

f engine oils
f manual and automatic gearbox oils

Warning: to ensure the engine operates optimally, the use
of a lubricant may be restricted to certain vehicles. Please
refer to your maintenance document.

Benefiting from the research applied to Formula 1,

lubricants are very high-tech products.

Updated with the help of RENAULT’s technical

teams, this range is perfectly compatible with the

specific features of the brand’s vehicles.

f ELF lubricants enhance

your vehicle’s performance significantly.

RENAULT recommends approved ELF lubricants for oil changes and top-ups.
Contact your RENAULT Dealer or visit www.lubrifiants.elf.com

Photo credit: Total/DPPI Imacom group

Une marque de

Welcome aboard your vehicle

This Driver’s Handbook contains the information necessary:
– for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and

the technical developments it incorporates.

– to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular main-

tenance.
– to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains

about the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too
pleased to provide you with any additional information.

The following symbol will help you when reading this handbook:

To indicate a hazard, danger or safety recommendation.

The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This hand­book covers all items of equipment (both standard and optional) available for these models, but whether or not these are
fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.

This handbook may also contain information about items of equipment to be introduced later in the model year.

Throughout the manual, the “approved dealer” is your DACIA dealer.

Enjoy driving your new vehicle.

Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manufac-

turer.

0.1

0.2

C O N T E N T S

Sections

Getting to know your vehicle ...............................

Driving ...................................................................

Your comfort .........................................................

Maintenance .........................................................

Practical advice ....................................................

Technical specifications ......................................

Alphabetical index ...............................................

1

2

3

4

5

6

7

0.3

0.4

Section 1: Getting to know your vehicle

Keys/Radio frequency remote control: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2

Locking/unlocking the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5

Opening/closing the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6

Engine immobiliser system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7

Front headrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8

Front seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9

Steering wheel, Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10

Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.11

Methods of restraint in addition to the front seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.15

Side protection devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.19

Additional methods of restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.20

Child safety: General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.21

child/baby seat mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.24

fitting the child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.26

deactivating/activating the front passenger air bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.32

Rear-view mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.35

Driving position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.36

Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.40

Displays and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.43

Trip computer and warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.45

Exterior lighting and signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.49

Adjusting the headlight beam height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.51

Audible and visual signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.52

Windscreen wash/Wipe/De-icing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.53

Fuel tank (filling with fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.55

1.1

KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (1/2)

A

1

Key A

1 Coded key for ignition switch,

doors and fuel filler cap.

The key must not be used
for any function other than
those described in the
handbook (removing the

cap from a bottle, etc.).

B

2

3

4

Radio frequency remote
control B

2 Locking the doors and tailgate.
3 Unlocking the doors and tailgate.

4 Coded key for ignition switch, driv-

er’s door and fuel filler cap.

Advice

Avoid leaving the remote control in
hot, cold or humid areas.

Driver’s responsibility

Never leave your vehicle
with the keys inside when
leaving a child (or animal)

in the car, even for a short period.
The reason for this is that the child

may endanger himself or others by
starting the engine, activating equip­ment such as the window winders
for example, or locking the doors.

Risk of serious injury.

1.2

KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (2/2)

The remote control unit
operating range

This varies according to the environ­ment. It is therefore important when
handling the remote control to ensure
that you do not lock or unlock the ve­hicle by inadvertently pressing the but­tons.

Interference

The presence of certain objects (metal
objects, mobile telephones, or an area
with strong electromagnetic radiation,
etc.) close to the key may create inter­ference and affect the operation of the
system.

Replacement and additional keys
or remote controls.

You must only contact an approved
Dealer:

– If you need to replace a key it will

be necessary to take the vehicle
and all of its keys to an approved
Dealer in order to initialise the
system.

– depending on the vehicle, you

have the option of using up to
four remote controls.

Remote control unit failure

Make sure that the correct battery
type is being used, and that the
battery is in good condition and in­serted correctly. These batteries
should have a service life of approx­imately two years.

Refer to Section 5: “Radio fre­quency remote control: batteries”
for the battery changing procedure.

1.3

RADIO FREQUENCY REMOTE CONTROL: use

Doors are locked and unlocked using
remote control unit B.

It is powered by a battery which must
be replaced (refer to the information on
the “Radio frequency remote control:
batteries” in Section 5).

B B

1

2

1.4

Locking the doors

Press locking button 1.
The hazard warning lights and side in-

dicator lights flash twice to indicate
that the doors have locked.

If a door or the tailgate is open or not
properly shut, the doors and tailgate
lock then quickly unlock and the hazard
warning lights and side indicator lights
do not flash.

Unlocking the doors

Press unlocking button 2.
The hazard warning lights and side in-

dicator lights flash once to indicate that
the doors have unlocked.

LOCKING/UNLOCKING THE DOORS

1

Manual locking

From the outside

Unlock the doors using the remote con­trol (refer to information on the “Radio
frequency remote control: use” in
Section 1) or using the key in one of the
door locks.

Depending on the vehicle, the key locks
and unlocks the driver’s door or all four
doors.

From the inside
(depending on vehicle)

Push in button 1 to lock and lift button 1
to unlock.

2

Electric central locking

Depending on the vehicle, it can be
used to simultaneously lock or unlock
the doors and luggage compartment.

Lock or unlock the doors by pressing
switch 2.

The front door mechanism cannot be
locked if the door is open.

Driver’s responsibility
If you decide to keep the doors locked when you are driving, remember

that it may be more difficult for those assisting you to gain access to the
passenger compartment in the event of an emergency.

3

Child safety

To make it impossible for the rear doors
to be opened from the inside, move
lever 3 on each door and check from
the inside that the doors are securely
locked.

1.5

OPENING AND CLOSING THE DOORS

2

1

Opening the doors manually
from the outside

With the doors unlocked (refer to the
information on “Locking/unlocking the
doors” in Section 1).

Front: Place your hand behind handle 1
and pull it towards you..

Rear (manual opening): lift unlocking
button 2 from the inside and move the
door handle.

Opening the doors from the
inside

Front: pull handle 3.
Rear: from the inside, lift unlocking

button 2 and pull door handle 3.

Lights-on reminder buzzer

If you have left the lights on after switch­ing off the ignition, a warning buzzer will
sound when a front door is opened (to
prevent the battery from discharging,
etc.).

Driver’s responsibility
when parking or stopping
the vehicle

child or adult who is not self-suffi­cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,

3

activating equipment such as the
electric windows or by locking the
doors.
Also, in hot and/or sunny weather,
please remember that the tempera­ture inside the passenger compart­ment increases very quickly.

RISK OF DEATH OR SERIOUS
INJURY.

Never leave an animal,

As a safety precaution,
the doors should only be
opened or closed when the
vehicle is stationary.

1.6

ENGINE IMMOBILISER

This prevents the vehicle being
driven by anyone not in possession
of the vehicle’s coded ignition key.

Operating principle

The vehicle is automatically protected
a few seconds after the ignition is
switched off.

If the vehicle does not recognise the
coded ignition key, tell-tale light 1 will
flash continuously and the engine
cannot be started.

Any unauthorised work
carried out on the engine
immobiliser (computers,

wiring, etc.) could be dan­gerous. Work must be carried out
by qualified personnel.

1

System operation

When the ignition is switched on, tell­tale 1 lights up continuously for approx­imately three seconds and then goes
out. The vehicle has recognised the
code. You can then start the engine.

Vehicle protection

A few seconds after the ignition has
been switched off, tell-tale light 1 will
flash constantly.

The vehicle will only be protected after
the ignition has been switched off.

Operating faults

After the ignition has been switched
on, if warning light 1 continues to flash
or remains continuously lit, there is a
system operating fault.

In all cases, it is essential to contact
an approved dealer as only they are
qualified to repair the engine immobi­liser.

If the coded ignition key is faulty,
use the second key (supplied with
the vehicle).

1.7

FRONT HEADRESTS

1

A

2

B

2

3

4

Adjusting the height of headrest A

Press tab 1 and simultaneously slide
the headrest to the required position.

To raise the headrests A or B

Depending on the vehicle, press tabs 1
and 2 on the head restraint guides or
on button 3 or 4 and lift the headrest to
release it (tilt the seatback backwards if
necessary).

1.8

To refit headrests A or B

Insert headrest rods 2 into the holes (tilt
the seatback backwards if necessary).
Push the headrest in until it locks in po­sition.

The headrest is a safety
component. Ensure that it is
fitted and in the correct po-

sition: the top of your head
should be in line with the top of the
headrest.

Headrest B is fixed and its height
cannot be adjusted.

FRONT SEATS

1

2

3

To move forwards or
backwards

Lift bar 1 to release.
Release the bar in the desired position
and ensure it locks in place properly.

To raise or lower the driver’s
seat surface

Depending on the vehicle, lift lever 2,
adjust the seat base to the desired
height, then release the lever.

4

2

Heated seats

Depending on the vehicle, with the igni­tion on, press switch 3.

The system, which has a thermostat,
decides whether or not the heating is
needed.

To tilt the seatback

Move handle 5 and tilt the seatback to
the desired position.

5

For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.

We would advise you not to recline
the seatbacks too far to ensure that
the effectiveness of the seat belts is
not reduced.

Make sure that the seatbacks are
correctly locked in place.

Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.

1.9

STEERING WHEEL, CLOCK

2

1

2

3

Adjusting the steering wheel

Depending on the vehicle version, the
height of the steering wheel can be ad­justed. Lift lever 1 and place the steer­ing wheel in the desired position; lower
the lever to lock the steering wheel.

Make sure that the steering wheel is
correctly locked.

For safety reasons, only
adjust the steering wheel
when the vehicle is station­ary.

1.10

Resetting the clock

With the ignition on, select display 2

showing the total mileage and clock.
There are two ways to set the time:
– Pressing and holding button 3 allows

you to scroll through the hours and
minutes quickly;

– short presses on button 3 allow you

to set the time minute by minute.

If the electrical supply is cut (battery
disconnected, broken supply wire,
etc.), the clock will lose its time set­ting.

The clock must be reset.

For your safety, we recom­mend that you do not adjust
the clock while driving.

SEAT BELTS (1/4)

Always wear your seat belt when trav­elling in your vehicle. You must also
comply with the legislation of the par­ticular country you are in.

Make sure that the rear bench seat
is locked in position correctly so that
the rear seat belts will operate effi­ciently. Refer to the information on
the “Rear bench seat: functions” in
Section 3.

Incorrectly adjusted or
twisted seat belts may
cause injuries in the event

of an accident.
Use one seat belt per person,
whether child or adult.
Even pregnant women should wear
a seat belt. In this case, ensure that
the lap belt is not exerting too much
pressure on the abdomen, but do
not allow any slack.

Before starting, adjust your driving
position and then have each occu­pant adjust their seat belt to ensure
optimum protection.

Adjusting your driving position

(depending on the vehicle)
– Sit well back in your seat (having

removed your coat or jacket etc.).
This is essential to ensure your back
is positioned correctly;

– adjust the distance between the

seat and the pedals. Your seat

should be as far back as possible
while still allowing you to depress
the clutch pedal fully. The seatback
should be adjusted so that your arms
are slightly bent when you hold the
steering wheel;

– adjust the position of the steering

wheel.

– adjust the position of your head-

rest. For the maximum safety, your

head must be as close as possible to
the headrest;

– Adjust the height of the seat. This

adjustment allows you to select the
seat position which offers you the
best possible view.

1

2

Adjusting the seat belts

Sit with your back firmly against the
seatback.

Shoulder strap 1 should be as close as
possible to the base of the neck but not
on it.

Lap belt 2 must be worn flat over the
thighs and against the pelvis. The seat
belt must be worn as close to the body
as possible. i.e.: avoid wearing heavy
clothing or keeping bulky objects under
the belts, etc.

1.11

SEAT BELTS (2/4)

Unlocking

7

Press button 5 on catch 6; the seat belt
is wound up by the inertia reel. Guide
the buckle to facilitate this manoeuvre.

3

4

5

6

6

To fasten

Unwind the belt slowly and smoothly
and ensure that buckle 4 locks into
catch 6 (check that it is locked by pull­ing on buckle 4). If the belt jams, allow
it to return slightly before attempting to
unwind it again.

If your seat belt is completely jammed,
pull slowly, but firmly, so that just over
3 cm unwinds. Allow it to return slightly
before attempting to unwind it again.

If there is still a problem, contact an ap­proved dealer.

Adjusting the front seat belt
height

(depending on the vehicle)
Move button 7 to select the position you

require so that chest strap 3 is worn as
described above.

Make sure that the seat belt is locked
in position correctly after you have ad­justed it.

Seat belt reminder light

ß

Depending on the vehicle, it
comes on when the engine is started
if the driver’s seat belt is not fastened.
When the vehicle is being driven, it
comes on and a beep sounds for ap­proximately 2 minutes until the driver’s
seat belt is fastened.

1.12

SEAT BELTS (3/4)

7

8

9

Rear central seat belts 7

(depending on the vehicle)

Unwind the belt slowly from its hous­ing 8.

Click the buckle into black catch 9.

Check that the rear seat belts are positioned and operating correctly each
time the rear seats are moved.

7

12

11

10

Fasten sliding buckle 11 into red
catch 10.

Rear side seat belts 12

The belts are locked, unlocked and
adjusted in the same way as the front
belts.

13

14

15

16

Rear lap belt with manual
adjustment 13

(depending on the vehicle)

The strap should be worn flat over your
thighs and against your pelvis.
The belt should be worn so that it is
as close as possible to your body, i.e.
avoid wearing heavy clothing or keep­ing bulky objects under the belts.
To tighten, pull on free section 14 of the
belt.
To loosen, tilt adjusting buckle 16 per­pendicular to the seat belt, press the
buckle on the ring side while pulling lap
belt 15.

1.13

SEAT BELTS (4/4)

The following information applies to the vehicle’s front and rear seat belts.

– No modification may be made to the component parts of the restraint system (belts and seats and their mountings)

fitted originally. For special operations (e.g. fitting child seats) contact an approved Dealer.

– Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too

loosely may cause injury in the event of an accident.
– Never wear the shoulder strap under your arm or behind your back.
– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around

them.
– The belt should never be twisted.
– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as

they show any signs of wear.
– Make sure that the buckle is inserted into the appropriate catch.
– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly se-

cured.

1.14

SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (1/4)

Depending on the vehicle, they are
composed of:

– seat belt pretensioners;
– chest-level load limiters;
– air bags for the driver and front pas-

senger.

These systems are designed to act in­dependently or together when the vehi­cle is subjected to a frontal impact.

Depending on the severity
of the impact, the system
can trigger:

– seat belt locking;

– the seat belt pretensioner to hold

the occupant in the seat, and the

force limiter;
– the front air bag.

Pretensioner

With the ignition switched on, if the
vehicle is subject to a significant fron­tal impact the system may, depending
on the severity of the impact, trigger a
piston which instantly retracts the seat
belt.
The pretensioner holds the seat belt
against the body, holding the occupant
more securely against the seat, thus in­creasing the seat belt’s efficiency.

– Have the entire restraint

system checked following
an accident.

– No operation whatsoever
is permitted on any part of the
system (air bags, electronic con­trol units, wiring) and the system
components must not be reused
on any other vehicle, even if iden­tical.

– To avoid premature triggering

of the system which may cause
injury, only qualified Network per­sonnel are authorisedto work on
the methods of restraint in addi­tion to the front seat belt.

– The electric trigger system may

only be tested by a specially
trained technician using special
equipment.

– When the vehicle is scrapped,

contact an approved dealer for
disposal of the pretensioner and
airbag gas generators.

1.15

SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (2/4)

Load limiter

Above a certain level of impact force,
this mechanism is used to limit the force
of the belt against the body so that it is
at an acceptable level.

The air bag system uses
pyrotechnic principles. This
explains why, when the air

bag inflates, it will gener­ate heat, produce smoke (this does
not mean that a fire is about to start)
and make a noise upon detonation.
An air bag may inflate immediately,
causing some minor, superficial
grazing to the skin or other discom­fort.

1.16

Driver’s and passenger air
bags

These may be provided for the driver
and the front passenger seats.

The presence of this equipment is in­dicated by the words “Air bag” on the
steering wheel and the dashboard, and
a label on the base of the windscreen or
on the sun visor.

Each air bag system consists of:
– an air bag and gas generator fitted

on the steering wheel for the driver
and in the dashboard for the front
passenger;

– an electronic unit for system monitor-

ing which controls the gas generator
electrical trigger system;

– a special tell-tale light
– remote sensors.

å;

SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (3/4)

Operation

This system is only operational when
the ignition is switched on.

If a severe frontal impact occurs, the
air bag(s) inflate(s) rapidly, cushion­ing the impact of the driver’s head and
chest against the steering wheel and
the front passenger’s head against the
dashboard. The air bag then deflates
immediately so that the passengers are
not impeded in any way when they get
out of the vehicle.

The air bag system uses

pyrotechnic principles. This

explains why, when the air

bag inflates, it will gener­ate heat, produce smoke (this does
not mean that a fire is about to start)
and make a noise upon detonation.
In a situation where an air bag is
required, it will inflate immediately
and this may cause some minor, su­perficial grazing to the skin or other
problems.

In this case, a child seat MUST NOT be
fitted to the front passenger seat.

Allowing any other passenger to sit in
that seat is not recommended.

In these two cases, contact an ap­proved dealer as soon as possible.

1

Operating faults

Warning light 1 will light up on the in­strument panel when the ignition is
turned on and then go out after a few
seconds.

If it does not light up when the ignition
is switched on, or comes on when the
engine is running, there is a fault in the
system.

1.17

SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (4/4)

2

All of the warnings below are given
so that the air bag is not obstructed
in any way when it is inflated and
also to prevent the risk of serious in­juries caused by items which may be
dislodged when the air bag inflates.

Warnings concerning the driver’s air bag

– Do not modify the steering wheel or the steering wheel boss.
– Do not cover the steering wheel boss under any circumstances.
– Do not attach any objects (badge, logo, clock, telephone holder, etc.) to

the steering wheel boss.

– You must not remove the steering wheel (such work must only be performed

by trained personnel from our Network).

– When driving, do not sit too close to the steering wheel. Sit with your arms

slightly bent (see the information on “Adjusting your driving position” in
Section 1). This will allow sufficient space for the air bag to inflate properly and
be fully effective.

Warnings concerning the passenger airbag: location 2

– Do not attach or glue any objects (badge, logo, clock, telephone holder, etc.) to

the dashboard in the proximity of the air bag housing.

– Do not place anything between the dashboard and the passenger (pet, um-

brella, walking stick, parcels, etc.).

– The passenger must not put his or her feet on the dashboard or seat as there

is a risk that serious injuries may occur. In general, all parts of the body should
be kept away from the dashboard (knees, hands, head etc.).

– You should reactivate the passenger air bag as soon as you remove the child

seat to ensure the protection of the front passenger in the event of an impact.

IT IS PROHIBITED TO FIT A REAR-FACING CHILD

SEAT TO THE FRONT PASSENGER SEAT UNLESS THE

RESTRAINT SYSTEMS IN ADDITION TO THE FRONT

PASSENGER SEAT BELT HAVE BEEN DEACTIVATED.

(Refer to the information on “Deactivating the

frontpassenger air bag” in Section 1).

1.18

SIDE PROTECTION DEVICES

Side air bags

These air bags may be fitted to the front
seats and are deployed at the sides of
the seats (door side) to protect the oc­cupants in the event of a severe side
impact.

Warnings concerning the side air bag

– Fitting seat covers: seats equipped with an air bag require covers
specifically designed for your vehicle. Contact an approved dealer to find

out if such covers are available from our Network. The use of any covers
other than those designed for your vehicle (including those designed for an­other vehicle) may affect the operation of the air bags and reduce your protec­tion.

– Do not place any accessories, objects, or even pets, between the seatback,

the door and the internal fittings. Do not cover the seatback with objects such
as clothes or accessories. This may prevent the air bag from operating cor­rectly or cause injury when the air bag is deployed.

– No work or modification whatsoever may be carried out on the seat or internal

fittings, except by qualified personnel from our Network.

1.19

ADDITIONAL METHODS OF RESTRAINT

All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when the air bag inflates.

The airbag is designed to complement the action of the seat belt. Both the airbags and seat belts are integral parts of
the same protection system. It is therefore essential to wear the seat belt at all times. If seat belts are not worn, the oc­cupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of minor su­perficial injuries occurring when the airbag is deployed, although such minor injuries are always possible with airbags.

If the vehicle should overturn or suffer a rear impact, however severe, the pretensioners and air bags are not always triggered.
Impacts to the underside of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.

– No work or modification whatsoever may be carried out on any part of the driver or passenger air bag system (air bag, elec-

tronic unit, wiring, etc.), except by qualified personnel from our Network.

– To ensure that the system is in good working order and to avoid accidental triggering of the system which could cause injury,

only qualified personnel from our Network may work on the air bag system.

– As a safety precaution, have the air bag system checked if your vehicle has been involved in an accident, or is stolen or

broken into.
– When selling or lending the vehicle, inform the user of these points and hand over this driver’s handbook with the vehicle.
– When scrapping your vehicle, contact your approved Dealer for disposal of the gas generator(s).

1.20

CHILD SAFETY: General information (1/2)

Carrying children

Children, and adults, must be correctly
seated and strapped in for all journeys.
The children being carried in your vehi­cle are your responsibility.

A child is not a miniature adult. Children
are at risk of specific injuries as their
muscles and bones have not yet fin­ished growing. The seat belt alone
would not provide suitable protection.
Use an approved child seat and ensure
you use it correctly.

A collision at 30 mph
(50 km/h) is the same as fall­ing a distance of 10 metres.
Transporting a child without

To prevent the doors being
opened, use the childproof
locks (refer to the informa­tion on “Locking/unlocking

the doors” in Section 1).

a restraint is the equivalent of allow­ing him or her to play on a fourth­floor balcony without railings.
Never travel with a child held in your
arms. In the event of an accident,
you will not be able to keep hold of
the child, even if you yourself are
wearing a seat belt.
If your vehicle has been involved in
a road accident, replace the child
seat and have the seat belts and
ISOFIX fittings checked.

Never leave a child unat­tended in the vehicle.

Check that your child is

always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.

Never let your child put their head or
arms out of the window.

Check that the child is in the correct
position for the entire journey, espe­cially if asleep.

1.21

CHILD SAFETY: General information (2/2)

Using a child seat

The level of protection offered by the
child seat depends on its ability to re­strain your child and on its installation.
Incorrect installation compromises the
protection it offers the child in the event
of harsh braking or an impact.

Before purchasing a child seat, check
that it complies with the regulations for
the country you are in and that it can
be fitted in your vehicle. Consult an ap­proved dealer to find out which seats
are recommended for your vehicle.

Before fitting a child seat, read the
manual and respect its instructions. If
you experience any difficulties during
installation, contact the manufacturer
of the equipment. Keep the instructions
with the seat.

Set a good example by always fas­tening your seat belt and teaching
your child:
– to strap themselves in correctly;
– to always get in and out of the car

at the kerb, away from busy traf­fic.

Do not use a second-hand child
seat or one without an instruction
manual.
Check that there are no objects in
the vicinity of the child seat which
could impede its operation.

Never leave a child unat­tended in the vehicle.

Check that your child is

always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.

Never let your child put their head or
arms out of the window.

Check that the child is in the correct
position for the entire journey, espe­cially if asleep.

1.22

CHILD SAFETY: choosing a child seat

Rear-facing child seats

A baby’s head is, proportionally, heavier
than that of an adult and its neck is very
fragile. Transport the child in this po­sition for as long as possible (until the
age of 2 at the very least). It supports
the head and neck. Choose a bucket
type seat for better side protection and
replace it as soon as the child’s head
extends past the seat shell.

Forward-facing child seats

The child’s head and abdomen need to
be protected as a priority. A forward-fac­ing child seat which is firmly attached to
the vehicle will reduce the risk of impact
to the head. Transport your child in a
forward-facing seat with a safety har­ness or guard depending on the child’s
size. Choose a bucket type seat for
better side protection.

Booster cushions

From 15 kg or 4 years, the child can
travel using a booster seat, which will
enable the seat belt to be adapted
to suit his/her size and shape. The
booster seat cushion must be fitted with
guides to position the seat belt on the
child’s thighs rather than the stomach.
It is recommended that you use a seat­back fitted with a belt strap guide which
can be adjusted in terms of height to
position the seat belt in the centre of
the shoulder. It should never rest on the
neck or over the arm. Choose a bucket
type seat for better side protection.

1.23

CHILD SAFETY: mounting a child seat (1/2)

Attachment via the seat belt

The seat belt must be adjusted to
ensure that it is effective in the event of
harsh braking or an impact.

Ensure that the strap paths indicated
by the child seat manufacturer are re­spected.

Always check that the seat belt is cor­rectly fastened by pulling it up, then
pulling it out fully whilst pressing on the
child seat.

Check that the seat is correctly held by
moving it from side to side and back
to front: the seat should remain firmly
fixed.

Check that the child seat has not been
installed at an angle and that it is not
resting against a window.

Do not use the child seat

if it may unfasten the seat

belt restraining it: the base

of the seat must not rest on
the buckle and/or catch of the seat
belt.

The seat belt must never

be twisted or the tension

relieved. Never pass the

shoulder strap under the
arm or behind the back.
Check that the seat belt has not
been damaged by sharp edges.
If the seat belt does not operate nor­mally, it will not protect the child.
Consult an approved dealer. Do not
use this seat until the seat belt has
been repaired.

No modifications may be

made to the component

parts of the restraint system

(belts, ISOFIX and seats
and their mountings) originally fitted.

Attachment with the ISOFIX system

Authorised ISOFIX child seats are ap­proved in accordance with regulation
ECE-R44 in one of the three following
scenarios:
– ISOFIX universal 3 point forwardfac-

ing seat;
– ISOFIX semi-universal 2 point seat;
– specific.

For the latter two, check that your child
seat can be installed by consulting the
list of compatible vehicles.

Attach the child seat with the ISOFIX
locks, if these are provided. The ISOFIX
system allows quick, easy, safe fitting.

The ISOFIX system is composed of
2 rings for each rear side seat.

Before using an ISOFIX
child seat that you pur­chased for another vehicle,

check that its installation is
authorised. Consult the list of ve­hicles which can be fitted with the
seat with the equipment manufac­turer.

1.24

CHILD SAFETY: mounting a child seat (2/2)

1

It is essential to use the lug-

gage compartment anchor-

age point 3 to attach the

upper belt of the child seat.
It is forbidden to use other mounting

points to attach this strap.

2

The two ISOFIX rings 1 are located be­tween the seatback and the seat base
and are clearly visible.

To ensure your child seat can be easily
fitted and locked on rings 1, use access
guides 2 on the child seat.

The ISOFIX anchorage points have been exclusively designed for child
seats with the ISOFIX system. Never fit a different type of child seat, seat
belt or other objects to these fittings.

Check that nothing is obstructing the anchorage points.

If your vehicle has been involved in a road accident, have the ISOFIX fittings
checked and replace your child seat.

The third ring is used to attach the
upper strap on some child seats.

Fix the hook of the strap onto ring 3 and
pull the strap so that the seatback of the
child seat comes into contact with the
seatback of the vehicle seat.

3

1.25

CHILD SAFETY: Fitting a child seat (1/6)

Some seats are not suitable for fitting
child seats. The diagram on the follow­ing page shows you how to attach a
child seat.

The types of child seats indicated may
not be available. Before using a differ­ent child seat, check with the manufac­turer that it can be fitted.

Fit the child seat in a rear
seat wherever possible.

Check that when installing

the child seat in the vehicle
it is not at risk of coming loose from
its base.

If you have to remove the headrest,
check that it is correctly stored so
that it does not come loose under
harsh braking or impact.

Always attach the child seat to the
vehicle even if it is not in use so that
it does not come loose under harsh
braking or impact.

In the front seat

The laws concerning children travel­ling in the front passenger seat differ in
every country. Consult the legislation in
force and follow the indications on the
diagram on the following page.

Before fitting a child seat in this seat (if
authorised):
– deactivate the front passenger air

bag;
– lower the seat belt as far as possible;
– move the seat as far back as possi-

ble;
– gently tilt the seatback away from

vertical (approximately 25°).
Do not change these settings after the

child seat is installed.

RISK O F DEATH OR
SERIOUS INJURY: before

fitting a child seat in this

seat, check that the air bag
has been deactivated (refer to the in­formation on “Deactivating the front
passenger air bag” in Section 1).

1.26

CHILD SAFETY: Fitting a child seat (2/6)

In the rear side seat

A carrycot can be installed across the
vehicle and will take up at least two
seats. Position the child with his or her
feet nearest the door.

Before installing a child seat in the
ISOFIX anchoring points on a rear side
seat, check that the seat belt buckles
are not placed between the two ISOFIX
anchorage points in this seat. If neces­sary, move the buckle for the seat con­cerned towards the centre of the vehi­cle.

Move the front seat as far forward as
possible to install a rear-facing child
seat, then move back the seat in front
as far as it will go, although without al­lowing it to come into contact with the
child seat.

For the safety of the child in the for­ward-facing seat, do not move the seat
in front back past the middle of the
runner, do not tilt the seatback too far
(maximum of 25° ) and raise the seat as
much as possible.

Check that the forward-facing child seat
is resting against the back of the vehi­cle seat and that the headrest of the ve­hicle is not obstructing its use.

Check that neither the child
seat nor the child’s feet
prevent the front seat from

locking into place. Refer to
the information on the “Front seat”
in Section 1.

Rear centre seat

A child seat may only be fitted in this
seat if it is equipped with an inertia-reel
seat belt. For any additional informa­tion, contact an approved dealer.

1.27

CHILD SAFETY: Fitting a child seat (3/6)

Vehicles without airbag or with airbag deactivated

³ Check the status of the air bag

before fitting a child seat or allowing a
passenger to use the seat.

RISK O F DEATH OR
SERIOUS INJURY: before

installing a child/baby seat

on the front passenger seat,
check that the air bag has been de­activated (refer to “Deactivating the
front passenger air bag” at the end
of the paragraph).

² Seat not suitable for fitting child

seats.

Child seat attached using the belt

¬ Seat which allows a child seat

with “Universal” approval to be attached
by a seat belt.

− Seat which only allows a rear-

facing seat with “Universal” approval

to be attached with a seat belt.

Only if the seat is equipped with an

1

inertia-reel belt.

Child seat attached using the ISOFIX
mounting

ü Seat which allows an ISOFIX

child seat to be fitted.

± The rear seats are fitted with

an anchorage point which allows a
forward-facing ISOFIX child seat with

1

universal approval to be fitted. The an­chorage points are located under the
luggage compartment carpet and are
indicated by a marking.

The size of the ISOFIX child seat is in­dicated by a letter:
– A, B and B1: for forward-facing seats

in group 1 (9 to 18 kg);

– C: rear-facing seats in group 1 (9 to

18 kg);

– D and E: shell seat or rear-facing

seats in group 0 or 0+ (less than
13 kg);

– F and G: cots in group 0 (less than

10 kg).

Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.

They risk serious or even fatal injury.

1.28

CHILD SAFETY: Fitting a child seat (4/6)

Vehicles with passenger air bag not deactivated

Child seat attached using the belt

² A child seat must not be fitted in

this seat

RISK O F DEATH OR

SERIOUS INJURY: never

fit a child seat to this seat.

¬ Seat which allows a child seat

with “Universal” approval to be attached
by a seat belt.

Only if the seat is equipped with an

1

inertia-reel belt.

Child seat attached using the ISOFIX
mounting

ü Seat which allows an ISOFIX

child seat to be fitted.

± The rear seats are fitted with

an anchorage point which allows a
forward-facing ISOFIX child seat with

1

universal approval to be fitted. The an­chorage points are located under the
luggage compartment carpet and are
indicated by a marking.

The size of the ISOFIX child seat is in­dicated by a letter:
– A, B and B1: for forward-facing seats

in group 1 (9 to 18 kg);

– C: rear-facing seats in group 1 (9 to

18 kg);

– D and E: shell seat or rear-facing

seats in group 0 or 0+ (less than
13 kg);

– F and G: cots in group 0 (less than

10 kg).

Using a child safety system which is not approved for this vehicle will not
correctly protect the baby or child. They risk serious or even fatal injury.

1.29

CHILD SAFETY: Fitting a child seat (5/6)

The table below summarises the information already shown on the diagram on the previous pages, to ensure the regula­tions in force are respected.

Front

passenger

seat without

airbag

(1)

Rear

side

seats

Rear

centre

seat

(7)

Type of child seat

Ca r r y co t f i t t ed
across the vehicle

Group 0

She l l s eat/Re a r ­facing seat

Group 0, 0+ and 1

Front passenger seat with airbag

Weight of

the child

< 10 kg F - G X X X U - IL (2) U

< 13 kg

9 kg to 18 kg

Seat

size

WITH deactivation

(1) (5)

E, D U X U U - IL (3) U

WITHOUT

deactivation (1) (6)

Rear-facing seat

Group 0+ and 1

Forward-facing seat

Group 1

Forward-facing seat

Group 1

Booster seat

Group 2 and 3

(5) RISK OF DEATH OR SERIOUS INJURY: before fitting a child seat on the front passenger seat, check that the air

bag has been deactivated (refer to the information on “Deactivating the front passenger air bag” in Section 1).

(6) RISK OF DEATH OR SERIOUS INJURY: never fit a child seat to this seat.

1.30

< 13 kg

9 kg to 18 kg

9 kg to 18 kg B, B1 X X X

9 kg to 18 kg A X X X U (4) U

15 to 25 kg

and 25 to

36 kg

C U X U U - IL (3) U

U - IUF

- IL
(4)

– X X X U (4) U

U

CHILD SAFETY: Fitting a child seat (6/6)

X = Seat not suitable for fitting child seats.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
IUF = Seat which, on equipped vehicles, allows forward-facing child seats with “Universal” approval to be attached by the ISOFIX

system; check that it can be fitted.

IL = Seat which, on equipped vehicles, allows child seats with “Semi-Universal” or “Specific to vehicle” approval to be attached by

the ISOFIX system; check that it can be fitted.

Refer to the brochure “Child safety equipment” available from the Network to choose the seat suited to your child and
recommended for your vehicle.

(1) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,

tilting the seatback slightly (approximately 25°).

(2) A carrycot can be installed across the vehicle and will take up two seats. Position the child with his or her feet nearest the door.
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will

go, although without allowing it to come into contact with the child seat.

(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the

headrest, or remove it if necessary. Do not push the seat in front of the child more than halfway back on its runners and do not
recline the seatback more than 25°.

(7) Only if the seat is equipped with an inertia-reel belt.

1.31

CHILD SAFETY: deactivating/activating the front passenger air bag (1/3)

2

1

Deactivating the front
passenger air bag

(depending on vehicle)

To fit a rear-facing child seat on the
front passenger seat, you must deacti­vate the front passenger air bag if your
vehicle is fitted with air bag deactiva­tion.

To deactivate the passenger air bag,
with the vehicle stopped and the igni­tion off, press and turn button 1 to the
OFF position.

1.32

When the ignition has been switched
back on, it is essential to check that

the warning light 2, ], is lit on the

instrument panel.

This warning light remains continu­ously lit to let you know that you can
fit a child seat.

The passenger air bag must
be activated or deactivated
with the ignition off.

If handled when the igni-

tion is on, the warning light
comes on.

Switch the ignition off then on again
to reset the air bag in accordance
with the lock.

å

CHILD SAFETY: deactivating/activating the front passenger air bag (2/3)

A

A

3

The markings on the dashboard and
labels A on each side of passenger sun
blind 3 (example: label shown above)
remind you of these instructions.

DANGER

Since operation of the front
passenger air bag is not

of a rear-facing child seat, NEVER
fit a rear-facing child seat on a front
passenger seat with an active front
air bag. The child may suffer very
serious injuries if the air bag is trig­gered.

compatible with the position

1.33

CHILD SAFETY: deactivating/activating the front passenger air bag (3/3)

2

1

Activation of the front
passenger air bag

(depending on vehicle)

You should reactivate the air bag as
soon as you remove the child seat from
the front passenger seat to ensure the
protection of your front passenger in
the event of an impact.

To reactivate the air bag: with the ve­hicle stopped and the ignition off, press
and turn button 1 to the ON position.

With the ignition on, it is essential to

check that warning light 2,

1.34

], is off.

Operating faults

It is forbidden to fit a rear-facing child
seat to the front passenger seat if the
air bag activation/deactivation system
is faulty.

Allowing any other passenger to sit in
that seat is not recommended.

Contact your approved dealer as soon
as possible.

REAR VIEW MIRRORS

1

Door mirrors with manual
adjustment

To adjust the mirror, move lever 1.

Foldable door mirrors

Fold the door mirror manually against
the door window.

B

0

A

2

Door mirrors with electrical
adjustment:

With the ignition on, move button 2:

– position A to adjust the left-hand

door mirror;

– position B to adjust the right-hand

door mirror;

0 is the neutral centre position.

Heated door mirrors

The mirror is de-iced when the rear
screen is de-iced/demisted; refer to
the information on the “Heated rear
screen”.

3

Interior rear view mirror

Its position can be adjusted. When driv­ing at night, to avoid being dazzled by
the headlights of the vehicle behind,
depress the little lever located behind
the rear view mirror 3.

1.35

DRIVER’S POSITION, LEFT-HAND DRIVE (1/2)

The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY.

2 651 7 83 4 10 119

1.36

2425262729 28

2223

1921 20

1718

1213141516

DRIVER’S POSITION, LEFT-HAND DRIVE (2/2)

The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY.

1 Side air vent.

2 Demister outlet.

3 Stalk for:

– direction indicator lights,
– exterior lights,
– front fog lights,
– rear fog lights,
– horn.

4 Instrument panel.

5 Location for driver’s air bag.

6 Steering column stalk for wind-

screen and rear screen wash/wipe.
On-board computer information re­adout control.

7 Centre air vents.

8 Location for passenger air bag or

storage compartment.

9 Demister outlet.

10 Side air vent.

11 Passenger air bag activation/deac-

tivation switch.

12 Glove box.

13 Location for radio or storage com-

partment.

14 Electric window control.

15 Central door locking switch.

16 Hazard warning lights switch.

17 Heating and ventilation controls.

18 Cigar lighter.

19 Handbrake.

20 Rear window electric locking con-

trol.

21 Electric door mirror control.

22 Location for ashtray or cup holder.

23 Gear lever.

24 Heated rear screen control.

25 Electric window control.

26 Ignition switch.

27 Headlight beam height adjustment

control.

28 Bonnet release.

29 Fuse flap.

1.37

DRIVER’S POSITION, RIGHT-HAND DRIVE (1/2)

The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY.

1 42 3 5 6 7 8 9 10 11

14 12131516171826272829

1.38

19202122232425

DRIVER’S POSITION, RIGHT-HAND DRIVE (2/2)

The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY.

1 Side air vent.

2 Demister outlet.

3 Storage compartment or location

for passenger air bag.

4 Centre air vents.

5 Stalk for:

– direction indicator lights,
– exterior lights,
– front fog lights,
– rear fog lights.

6 Instrument panel.

7 Location for driver’s air bag (de-

pending on vehicle).

8 Windscreen wiper/washer stalk.

On-board computer information re­adout control.

9 Demister outlet.

10 Side air vent.

11 Fuse box.

12 Bonnet release.

13 Headlight beam height adjustment

control.

14 Ignition switch.

15 Location for radio or storage com-

partment.

16 Electric window control.

17 Central locking switch.

18 Hazard warning lights switch.

19 Heating and ventilation controls.

20 Cigar lighter.

21 Handbrake.

22 Rear window electric locking con-

trol

23 Electric door mirror control.

24 Location for ashtray or cup holder.

25 Gear lever.

26 Heated rear screen control.

27 Electric window control.

28 Glove box.

29 Passenger air bag activation/deac-

tivation switch.

1.39

WARNING LIGHTS (1/3)

The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.

A

Instrument panel A

The û warning light re-

quires you to stop immedi-

ately, for your own safety,
as soon as traffic conditions allow.
Switch off the engine and do not re­start it. Contact an approved Dealer.

m
o
#

This lights up on the instrument panel
when an oil change is required.
Change the oil or have it changed as
soon as possible.

Only the distance travelled between two
oil changes is taken into account; the
time interval between two oil changes
is not.
The oil should always be changed
when the first threshold is reached, i.e.
either the distance travelled or the inter­val specified in your vehicle’s mainte­nance document. This means you may
have to change the oil before the warn­ing light comes on.
Refer to the information on the “Oil
change” in Section 4.

Dipped beam headlight tell­tale light

Main beam headlight tell-tale
light

Engine oil change warning
light

x

This light comes on when the ignition is
switched on and goes out within three
seconds. If it lights up when you are
driving, it indicates a fault in the anti­lock braking system. Braking will then
be as normal, without the ABS system:
contact an approved dealer urgently.

]

Refer to the information on “Child
Safety” in Section 1.

ç

let you know that the seat belt has been
correctly fastened.

Anti-lock braking warning
light

Front passenger air bag de­activation warning light.

Seat belt reminder light

This warning light goes out to

If no lights or sounds are ap­parent, this indicates a fault
in the instrument panel. This

indicates that it is essential
to stop immediately (as soon as traf­fic conditions allow). Ensure that the
vehicle is correctly immobilised and
contact an approved Dealer.

1.40

WARNING LIGHTS (2/3)

The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.

Ô

This goes out as soon as the engine
starts. If it comes on when driving, it
indicates an increase in the coolant
temperature. Stop and let the engine
idle for a minute or two; the tempera­ture should fall. If it does not fall, stop
the engine and allow it to cool before
checking the coolant level. If the level is
normal, there is another cause. Consult
an approved dealer.

À

engine starts; if it comes on when you
are driving, stop at once and switch off
the ignition. Check the oil level.

If the level is normal, the indicator light
is being lit by something else. Contact
an approved Dealer.

d

Coolant temperature warn­ing light

Oil pressure warning light

It should go out as soon as the

Direction indicator tell-tale
light

ê

This light performs several functions.
Refer to the information on the “Engine

immobiliser” in Section 1.

6

This light should come on when the ig­nition key is in position M; it indicates
that the heater plugs are in operation.

It goes out when preheating is com­plete and the engine can be started.

Electronic fault warning light

If it remains lit or comes on when you
are driving, it indicates an electrical or
electronic fault. Contact an approved
dealer as soon as possible

V

Engine immobiliser system
warning light

Electronic fault or preheat­ing warning light

Preheating warning light

Rear screen de-icing/de­misting indicator light

Ú

engine starts.
If it comes on when you are driving, it

indicates that the circuit is overcharging
or has discharged. Stop and contact an
approved Dealer.

Ä

On equipped vehicles, the light comes
on when the ignition is switched on then
goes out.

– If it comes on continuously, consult

– If it flashes, reduce the engine speed

Ref er t o the info rmation on
“Antipollution, fuel economy and driv­ing” in Section 2.

Battery charge warning light

It should go out as soon as the

Toxic Fume Filter System
Warning Light

an approved dealer as soon as pos­sible.

until the light stops flashing. Contact
an approved dealer as soon as pos­sible.

1.41

WARNING LIGHTS (3/3)

The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.

A

Instrument panel A

The û warning light re-

quires you to stop immedi-

ately, for your own safety,
as soon as traffic conditions allow.
Switch off the engine and do not re­start it. Contact an approved Dealer.

D

If it lights up, check that the hand brake
is fully released. If not, it indicates that
the fluid level is low in one of the cir­cuits. It may be dangerous to continue
driving, contact an approved dealer.

f
g
Å
û

is switched on and goes out as soon as
the engine is started.

L

is started then goes out after three sec­onds. If it stays on, fill up with fuel as
soon as possible.

Handbrake on and brake cir­cuit incident warning light

Rear fog light tell-tale

Front fog light tell-tale

Door status warning light

STOP light

This lights up when the ignition

Low fuel level warning light

It comes on when the engine

î

LPG system for vehicles which are
equipped with it.

å

is switched on and goes out after a few
seconds.

If it does not light up when the ignition
is switched on, or lights up when the
engine is running, there is a fault in the
system.

Refer to the information on “Systems
in addition to the front seat belts” in
Section 1.

Contact an approved dealer as soon as
possible.

^

If it remains lit or comes on while driv­ing, it indicates that water is present in
the diesel filter. Contact an approved
dealer as soon as possible.

LPG mode indicator

Refer to the document for the

Air bag warning light

This lights up when the ignition

Water in the diesel filter
warning light

1.42

DISPLAYS AND INDICATORS (1/2)

1

2

Rev counter 1 (rpm × 1 000) Speedometer 2 (km or miles

per hour)

Overspeed buzzer

Depending on the vehicle, a buzzer
sounds for approximately 10 seconds
every 30 seconds, as long as the ve­hicle is travelling in excess of 72 mph
(120 km/h).

Speedometer 2 Dual speed
scale (miles per hour and km
per hour)

(depending on vehicle)

1.43

DISPLAYS AND INDICATORS (2/2)

3

4

Multifunction key 5

A

5

– Display selection

By pressing the button you can shift
from the total mileage recorder, trip
mileometer and time or vice-versa.

– Resetting the trip mileage re-

corder

Once the trip mileage display is se­lected, press and hold the button.

– Resetting the clock

Refer to the information on the
“Clock” in Section 1.

Fuel gauge 3

The number of squares lit shows the
fuel level. When it is at minimum, the
squares disappear and the low fuel
level warning light comes on.

Coolant temperature
indicator 4

The number of squares lit depends on
the engine coolant temperature. There
is no warning unless the last three
squares light up.

1.44

Multifunction display A

Total mileage recorder, distance trav­elled trip mileometer, clock.

OR

Trip computer and warning
system

Refer to the information on the “Trip
computer and warning system” in
Section 1.

TRIP COMPUTER AND WARNING SYSTEM (1/4)

The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

1

Refer to the table on the following
pages showing display examples.

2

Display 1

General reset and trip
mileage recorder reset key 2

To reset the trip mileage recorder, the
display must show the Trip mileometer
function.

Press and hold button 2.

3

Display selection key 3

Keep pressing key 3 briefly to scroll
through the following information (de­pending on the vehicle) in sequence:

a) total mileage recorder,
b) trip mileage recorder,
c) fuel used,
d) average consumption,
e) estimated range,
f) distance travelled,
g) average speed.

1.45

TRIP COMPUTER AND WARNING SYSTEM (2/4)

The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Interpreting some of the
values displayed after
resetting

The values showing average fuel con­sumption, range and average speed
will become more stable and reliable
the further you travel after pressing the
reset button.

For the first few miles after pressing the
reset key you will notice that the range
increases as you travel. This range
takes into account the average fuel con­sumption since the last time the reset
button was pressed. Therefore, the fuel
consumption may decrease when:

– the vehicle stops accelerating;
– the engine reaches its operat-

ing temperature (if the engine
was cold when the reset key was
pressed);

– driving from an urban area onto

the open road;

Therefore, if the average fuel con-

sumption decreases, the range
will increase.

– You may also notice that the aver-

age fuel consumption increases
when the vehicle is stationary and
the engine idling.

This is normal, since the computer
takes account of fuel used during
idling.

Manually resetting the journey param­eters: with the display showing one of
the journey parameters, press button 2
until the display is reset.

Automatically resetting the journey pa­rameters: the reset is automatic when
the capacity of one of the memories is
exceeded.

1.46

TRIP COMPUTER AND WARNING SYSTEM (3/4)

The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of display selec­tions by repeatedly press­ing 3

Interpreting the display

a) Total mileage recorder.

b) Trip mileage recorder.

c) Fuel used since the last time the reset button was pressed.

d) Average fuel consumption since the last time the reset button was pressed.

This value is displayed after driving 400 metres and takes into account the
distance travelled and the fuel used since the last time the reset button was
pressed.

1.47

TRIP COMPUTER AND WARNING SYSTEM (4/4)

The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of display
selections by repeatedly
pressing 3

Interpreting the display

e) Estimated range with remaining fuel

This range takes into account the average fuel consumption since the last time
the reset button was pressed.
The value is displayed after driving around 400 metres.

f) Distance travelled since the last reset.

g) Average speed since the last reset.

The value is displayed after driving around 400 metres.

1.48

EXTERIOR LIGHTING AND SIGNALS (1/2)

u

symbol is opposite mark 2.

Side lights

Turn the end of stalk 1 until the

Before driving at night, check that the electrical equipment is operating

correctly and adjust the headlight beams (if your vehicle is not carrying

its normal load).

Check that the lights are not obscured (by dirt, mud, snow or objects
which could cover them).

1

k

Turn the end of stalk 1 until the symbol
is opposite mark 2.

An indicator light on the instrument
panel will come on.

Dipped beam
headlights

2

á

headlights position, move the stalk to­wards you.

When the main beam headlights are lit,
an indicator light lights up on the instru­ment panel.

To return to the dipped beam headlight
position, pull the switch stalk towards
you.

e

initial position.

Lights-on reminder buzzer

A warning buzzer will sound when a
front door is opened and the lights
are left on after the ignition has been
switched off (to prevent discharge of
the battery).

Main beam headlights

With stalk 1 in dipped beam

Switching off the lights

Return the end of stalk 1 to its

1.49

EXTERIOR LIGHTING AND SIGNALS (2/2)

3

g

until the symbol is opposite mark 4.
The fog lights only light up if the exterior

lights have been switched on. An indi­cator light on the instrument panel then
lights up.

Do not forget to switch off the fog lights
when they are no longer needed, to
avoid inconveniencing other road
users.

Front fog lights

Turn the centre ring of stalk 3

3 4

h

stalk 3 until the symbol is opposite
mark 4.

The fog lights only light up if the exterior
lights have been switched on. An indi­cator light on the instrument panel then
lights up.

Remember to switch off the these
lights when they are no longer required
to avoid inconveniencing other road
users.

Rear fog lights

Turn the centre ring of

e

Turn centre ring 3 again to position the
symbol corresponding to the fog light or
off position opposite mark 4. The corre­sponding indicator light goes out on the
instrument panel.

The front and rear fog lights switch off
when the exterior lights are switched
off.

Turning off the fog
lights

1.50

ADJUSTMENT OF HEADLIGHT BEAM HEIGHT

A

Control A is used to adjust the height
of the headlight beams according to the
load.

Turn control A anticlockwise to lower
the beams and clockwise to raise them.

Vehicle load conditions

Basic setting: luggage compartment empty and only the
driver on board or with one front passenger.

Luggage compartment empty, 1, 2, 3 passengers 1

Luggage compartment full, 3 passengers 2

Luggage compartment full, driver only 3

Setting position

of control A

0

1.51

AUDIBLE AND VISUAL SIGNALS

1

2

Horn

Press the end of the stalk 1.
Depending on the vehicle, press on one

of areas 2.

Headlight flasher

Pull stalk 1 towards you to flash the
headlights.

3

Hazard warning lights

é

This switch activates all four direction
indicators and the side indicator lights
simultaneously.

It must only be used in an emergency to
warn drivers of other vehicles that you
have had to stop in an area where stop­ping is prohibited or unexpected, or that
you are obliged to drive under special
conditions.

Press switch 3.

1

Direction indicators

Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it.

When driving on the motorway, the
steering wheel is not usually turned suf­ficiently to return the stalk automatically
to its starting position. There is an inter­mediate position in which the stalk may
be held when changing lanes.

When the stalk is released, it will auto­matically return to its starting position.

1.52

WINDSCREEN WASH/WIPE, DE-ICING (1/3)

1

D

n

stalk 1 around the steering wheel:
A Park.
B Intermittent wiping.

C Normal wiping speed.
D Fast wiping speed.

Windscreen wiper

With the ignition on, move

The wipers will pause for several
seconds between sweeps.

s

towards you.
A brief pull will trigger a single sweep

A

B

C

of the wipers, in addition to the wind­screen washer.

A longer pull will trigger three sweeps
of the wipers, in addition to the wind­screen washer.

Windscreen wiper

With the ignition on, pull stalk 1

When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in position A (park). Risk

of injury.

In frosty weather, make sure that
the wiper blades are not stuck by ice
(risk of motor overheating).

Keep an eye on the condition of the
blades. Replace the wiper blades as
soon as they begin to lose efficiency
(approximately once a year).

Clean your windscreen regularly.
If you switch off the ignition before

switching off the windscreen wiper
(position A) the blades will stop at
random on the windscreen.

After switching the ignition back on,
simply move stalk 1 to position A to
place them in the park position.

Before any action on the
windscreen (washing the
vehicle, de-icing, cleaning
the windscreen, etc.) return

stalk 1 to position A (park).
Risk of injury and/or damage.

1.53

WINDSCREEN WASH/WIPE, DE-ICING (2/3)

1

2

Y

With the ignition on, turn the end of
stalk 1 to align the symbol with mark 2.

Rear screen wiper

(depending on vehicle)

p

(depending on vehicle)

With the ignition on, turn the end of
stalk 1 to align the symbol with mark 2.

When the stalk is released, it returns to
the rear wipe position.

Rear screen washer/
wiper

Before using the rear wiper, check
that no object is obstructing the
travel of the blade.

In frosty weather, make sure that
the wiper blades are not stuck by ice
(to avoid the risk of the motor over­heating).

Keep an eye on the condition of the
blades. Replace the wiper blades as
soon as they begin to lose efficiency
(approximately once a year).

Regularly clean your rear screen.

1.54

WINDSCREEN WASH/WIPE, DE-ICING (3/3)

2

2

V

press button 2 (the indicator light on the
instrument panel lights up).
This function de-ices/demists the rear
screen and the electric de-icing rear­view mirrors (depending on the vehi­cle).

With the engine running,

Heated rear screen

The operation is stopped:
– automatically after it has been run-

ning for 12 minutes (the indicator
light goes out);

– by pressing button 2 again (the indi-

cator light goes out).

1.55

FUEL TANK (1/3)

A

1

B

Capacity of the fuel tank: 50 litres ap-

proximately.
The cap can be unlocked with the igni-

tion key.
For details on filling the fuel tank, refer

to the information on “Filling with fuel”.
There is a cap holder 1 on the fuel filler
flap for holding the cap when the tank is
being filled.

Do not mix even small
amounts of petrol (un­leaded or E85) with diesel.

Do not use ethanol-based
fuel if your vehicle is not compatible
with this fuel.
Do not add any additives to the fuel,
you risk damaging the engine.

Fuel filler cap: this is spe-

cific to the vehicle type. If

you have to replace it, make

sure the new cap is of the
same type. Contact an approved
dealer.

Never place the cap near a source
of heat or flame.

Do not wash the filler area with a
high-pressure washer.

Fuel grade

Always use a high-grade fuel that

complies with the legislation in force
in each country. It must conform to the
specifications given on label A inside
the fuel filler flap.

Refer to the “Engine specifications”
table in Section 6.

Vehicles running on ethanol-based
fuel

Always use unleaded petrol or fuel

containing a maximum of 85 percent
ethanol (E85).

In very cold conditions, it may be very
difficult or even impossible to start the
engine.

Note: you may notice an increase in
fuel consumption with this type of fuel.

When the fuel is changed the engine
must adjust, which may cause minor in­conveniences for a few minutes (longer
starting times, cutting out, etc.).

1.56

FUEL TANK (2/3)

A

B

Petrol version

It is essential to use unleaded petrol.
The octane rating (RON) must conform
with the specifications given on the
label inside the fuel filler flap A.

Diesel versions

It is essential to use diesel fuel that
conforms to the specifications given on
the label inside fuel filler flap A.

Filling with fuel

Insert the nozzle to open valve B and
insert it fully before turning it on to fill
the fuel tank (risk of splashing).

Hold it in this position for the whole fill­ing operation. Following the first auto­matic shut-off at the end of filling, the
trigger can be pulled two more times at
most, to leave room for expansion.

Make sure that no water enters the fuel
tank during filling. Valve B and its sur­round must remain clean.

Petrol versions

Using leaded petrol will damage the
antipollution system and may lead to a
loss of warranty.

To ensure that the fuel tank is not filled
with leaded petrol, the fuel tank filler
neck contains a restrictor fitted with a
foolproof system which only allows

the nozzle for unleaded petrol to be
used (at the pump).

Persistent smell of fuel
If you notice a persistent
smell of fuel you should:

– stop the vehicle as soon
as traffic conditions allow and
switch off the ignition;

– switch on the hazard warning

lights and ask your passengers to
leave the vehicle and stay clear
of the traffic;

– contact an approved Dealer.

1.57

FUEL TANK (3/3)

2

3

Priming bulb

(diesel version)
After a breakdown caused by com-

pletely running out of fuel, the system
must be reprimed before the engine is
restarted:

Note: the bulb is always located on the
right-hand side of the engine compart­ment.

Work bulb 2 until the fuel runs into
pipe 3.

If the engine does not start after several
attempts, contact an approved dealer.

No modifications what­soever are permitted on
any part of the fuel supply

system (computers, wiring,
fuel circuit, injector, protection
covers, etc.) as this may be danger­ous (such work must be undertaken
by qualified Network personnel).

The engine may be hot

when working in close prox-

imity. In addition, the engine

cooling fan may come on at
any moment.

Risk of injury.

1.58

Section 2: Driving

(Advice on use relating to fuel economy and the environment)

Running in, ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2

Starting/stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4

Special features of diesel versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5

Advice: antipollution, fuel economy and driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6

Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9

Gear lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10

Handbrake, Power-assisted steering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11

Driver correction devices/aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.12

Automatic gearbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.14

2.1

RUNNING IN, IGNITION SWITCH

Petrol version

For the first 600 miles (1,000 km), do
not exceed 78 mph (130 km/h) in the
highest gear, or 3,000 to 3,500 rpm.

You may only expect top performance
from your vehicle after approximately

1,800 miles (3,000 km).
Serv ice int ervals: refer to the

Maintenance Service Booklet for the
vehicle.

Diesel version

For the first 900 miles (1,500 km), do
not exceed 2,500 rpm. After complet­ing this mileage you may drive faster,
although you may only expect top per­formance after approximately 3,600
miles (6,000 km).

Do not accelerate hard while the engine
is still cold and do not let the engine
over-rev.

Serv ice int ervals: refer to the
Maintenance Service Booklet for the
vehicle.

Stop and steering lock
position St

To lock: remove the key and turn the
steering wheel until the steering column
locks.

To unlock: turn the key and the steering
wheel slightly.

Accessories position A

When the ignition is switched off, any
accessories (radio, etc.) will continue to
function.

Ignition on position M

The ignition is switched on:
– petrol version: the engine may be

started.

– diesel version: the engine is pre-

heating.

Start position D

If the engine fails to start at the first
attempt, the key must be turned back
before the starter can be activated
again.

Release the key as soon as the engine
starts.

2.2

STARTING/STOPPING THE ENGINE

Starting the engine

In very cold conditions (temperatures
below –20°C): so that it is easier to
start the engine, switch on the ignition
for several seconds before starting the
engine.

Make sure the engine immobiliser is not
activated. Refer to the information on
the “Engine immobiliser” in Section 1.

Never leave your vehicle with the key or remote control inside and never leave a child (or a pet) unsupervised, even
for a short while.

The reason for this is that the child may endanger himself or others by starting the engine, activating equipment such

as the window winders for example, or locking the doors.
Risk of serious injury.
Never switch off the ignition before the vehicle has stopped completely. Once the engine has stopped, the brake servo,

power assisted steering and passive safety equipment such as air bags will no longer operate.
The steering is locked when the key is removed.

Vehicle equipped with an automatic
gearbox

Before starting, move the lever to posi­tion N or P.

Refer to the information on the
“Automatic gearbox” in Section 2.

Petrol injection

Engine warm or cold
– Activate the starter without de-

pressing the accelerator.

– Release the key as soon as the

engine starts.

É

Turn the ignition key to ignition “On” po­sition M, and hold this position until the
preheating warning light goes out.

Move the key to “Start” position D with-
out accelerating. Release the key as
soon as the engine starts.

Stopping the engine

With the engine idling, turn the key
back to “Stop” position St.

Diesel injection

2.3

SPECIAL FEATURES OF PETROL VERSIONS

The following operating conditions:
– driving for long periods when the low

fuel level warning light is lit;
– using leaded petrol;
– using oil or fuel additives which are

not approved by the manufacturer.
Or operating faults such as:
– faulty ignition system, running out of

fuel or disconnected spark plugs re-

sulting in the engine misfiring or cut-

ting out when driving;
– loss of power,
may cause the catalytic converter to

overheat, reducing its efficiency which

may irreparably damage it and cause
heat damage to the vehicle.

If you notice any of the above operating
faults, have the necessary repairs car­ried out as soon as possible by an ap­proved Dealer.

These faults may be avoided by reg­ularly taking your vehicle to your ap­proved dealer at the intervals speci­fied in your Maintenance Service
Document.

Starting problems

To avoid damaging the catalytic con­verter, do not keep trying to start the
engine (using the start button, or by
pushing or towing the vehicle) without

having identified and corrected the
starting fault.

If the fault cannot be identified, do not
continue to try and start the engine, but
contact an approved dealer.

Do not park the vehicle or
run the engine in locations
where combustible sub-

stances or materials such
as grass or leaves can come into
contact with a hot exhaust system.

2.4

SPECIAL FEATURES OF DIESEL VERSIONS

Diesel engine speed

Diesel engines are fitted with an injec­tion pump which prevents the engine
speed being exceeded irrespective of
the gear selected.

When driving, depending on the fuel
grade used, it is possible that white
smoke may be emitted.

This is due to the exhaust particle filter
being cleaned automatically, and does
not affect the way the vehicle runs.

Running out of fuel
If the tank has been completely

drained, the system must be reprimed

after the tank is refilled: see information
on the “Fuel tank” in Section 1 before
restarting the engine.

Precautions to be taken in winter

To avoid any faults in icy weather:
– ensure that the battery is always fully

charged,

– always keep the diesel tank rela-

tively full to avoid water vapour con­densing in it and accumulating at the
bottom of the tank.

Do not park the vehicle or

run the engine in locations

where combustible sub-

stances or materials such
as grass or leaves can come into
contact with a hot exhaust system.

2.5

ADVICE: antipollution, fuel economy and driving (1/3)

By virtue of its design, moderate fuel
consumption and initial settings, your
vehicle conforms to current antipol­lution regulations. The manufacturer
is actively striving to reduce pollutant
exhaust gas emissions and to save
energy. But the fuel consumption of
your vehicle and the level of pollutant
exhaust gas emissions are also your
responsibility. Ensure that it is main­tained and used correctly.

Maintenance

It should be noted that failure to respect
antipollution regulations may lead to
legal action being taken against the
vehicle owner. In addition, replacing
engine, fuel supply system and exhaust
components with parts other than those
originally recommended by the manu­facturer may alter your vehicle so that
it no longer complies with antipollution
regulations.

Have your vehicle adjusted and
checked by an approved Dealer, in ac­cordance with the instructions given in
your maintenance schedule: they will
have all the equipment necessary for
ensuring that your vehicle is maintained
to its original standard.

Engine adjustments

– ignition: this does not require ad-

justment.

– spark plugs: for optimum fuel econ-

omy, efficiency and performance
the specifications laid down by our
Design Department must be strictly
applied.

If the spark plugs have to be
changed, use the make, type and
gap specified for your vehicle’s
engine. Contact an approved dealer
for this.

– idle speed: this does not require ad-

justment.

– air filter, diesel filter: a choked el-

ement hinders performance. It must
be replaced.

2.6

ADVICE: antipollution, fuel economy and driving (2/3)

Exhaust gas monitoring
system

The exhaust gas monitoring system de­tects operating faults in the vehicle’s
antipollution system. These faults may
cause mechanical damage or the re­lease of harmful substances.

Ä

there are any faults in the system:
This comes on when the ignition is

switched on and goes out after three
seconds.
– If it comes on continuously, consult

– If it flashes, reduce the engine speed

This warning light on the in­strument panel will indicate if

an approved dealer as soon as pos­sible.

until the light stops flashing. Contact
an approved dealer as soon as pos­sible.

Driving

– Drive carefully for the first few miles

until the engine reaches its normal
operating temperature, rather than
let it warm up while the vehicle is sta­tionary.

– Speed is expensive.
– Sporty driving uses a lot of fuel: drive

with a light right foot.

– Study the road ahead so that you are

able to brake as little as possible, it
can be sufficient just to lift off the ac-

celerator.
– Avoid sudden acceleration.
– Do not overrev the engine in the in-

termediate gears. Always use the

highest gear possible without labour-

ing the engine.

On versions with an automatic gear-

box, it is preferable to keep the gear
lever in position D.

– Do not try to maintain the same

speed up a hill, accelerate no more
than you would on the level. Keep
your foot in the same position on the
accelerator pedal.

– Double declutching and accelerating

before switching off are unnecessary
in modern vehicles.

– Poor weather conditions, flooded

roads. Do not drive through water if it
is higher than the lower edge of the
wheel rim.

Driving problems

On the driver’s side, only
use mats specially adapted

for the vehicle and attached
to prefitted devices. Check regularly
to make sure they are secure. Do
not overlay several mats.

Risk of pedals jamming.

2.7

ADVICE: antipollution, fuel economy and driving (3/3)

– In vehicles fitted with air condi-

tioning, it is normal to observe an

increase in fuel consumption (es­pecially in urban conditions) when
it is used. For vehicles fitted with
manual air conditioning, switch off
the system when it is not required.

Advice for reducing consumption
and therefore helping to preserve
the environment:

If the vehicle has been parked in the
sun, open the doors for a few mo­ments to let the hot air escape before
starting the engine.

Advice on use

– Electricity is fuel; switch off all the

electrical components which are not
really needed.

However (safety first), keep your
lights on when the visibility is bad
(“see and be seen”).

– Use the air vents. Driving with the

windows open at 60 mph (100 km/h)
will increase fuel consumption by
4%.

– Never fill the fuel tank right to the

brim to avoid overflow.

– Do not leave an empty roof rack

fitted to the vehicle.

– It is better to fit a trailer for bulky ob-

jects.

– When towing a caravan, fit a wind

deflector and adjust it carefully.

– Avoid using the vehicle for door-to-

door journeys (short journeys, with
long stops in-between) because in
these conditions, the engine never
reaches its ideal temperature.

Tyres

Increased fuel consumption could be
the result of:

– insufficient pressure,
– using non-recommended tyres.

2.8

ENVIRONMENT

Your vehicle has been designed with
respect for the environment in mind for
its entire service life: during production,
use and at the end of its life.
This commitment is illustrated by the
Dacia eco² group signature.

Manufacture

Your vehicle has been manufactured at
an industrial site which uses a progress
policy to reduce environmental impacts
on rivers and natural areas (reduc­tion of water and energy consumption,
visual and noise pollution, atmospheric
emissions and waste water, sorting and
reusing waste).

Emissions

Your vehicle has been designed to
emit fewer greenhouse gases (CO2)
while in use, and therefore to consume
less fuel (e.g. 140 g/km, equivalent to

5.3 l/100 km for a diesel vehicle).
Our vehicles are also equipped with a
particle filter system including a cata­lytic converter, an oxygen sensor and
an active carbon filter (the latter pre­vents vapour from the fuel tank being
released into the open air).

For certain diesel vehicles, this system
also has a particle filter to reduce the
volume of soot particles emitted.

Please make your own
contribution towards
protecting the environment
too.

– Worn parts replaced in the course

of routine vehicle maintenance (bat­tery, oil filter, air filter, batteries, etc.)
and oil containers (empty or filled
with used oil) must be disposed of
through specialist organisations.

– At the end of the vehicle’s service

life, it should be sent to approved
centres to ensure that it is recycled.

– In all cases, comply with local legis-

lation.

Recycling

Your vehicle is 85% recyclable and
95% recoverable.

To achieve these objectives, many of
the vehicle components have been de­signed to enable them to be recycled.
The materials and structures have
been carefully designed to allow these
components to be easily removed and
reprocessed by specialist companies.
In order to preserve raw material re­sources, this vehicle incorporates nu­merous parts made from recycled plas­tics or renewable materials (vegetable
or animal-derived materials such as
cotton or wool).

2.9

GEAR LEVER

1

To select reverse gear

(vehicle stationary)

Vehicle with manual gearbox

Move the lever to neutral, then follow
the gate shown on knob 1.

Vehicle with automatic gearbox

Refer to the information on the
“Automatic gearbox” in Section 2.

The reversing light will come on as
soon as reverse gear is selected (igni­tion on).

An impact to the under­side of the vehicle while
manoeuvring (e.g.: strik-

ing a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: defor­mation of an axle).

To prevent any risk of accident,
have your vehicle checked by an
approved dealer.

2.10

HANDBRAKE, POWER-ASSISTED STEERING

2

1

Handbrake

To release

Pull lever 1 up slightly, press button 2
and then lower the lever to the floor.

Make sure that the hand­brake is properly released
when driving (red indicator

light off), otherwise over­heating, or even damage, may
occur.

To apply

Pull lever 1 upwards and make sure the
vehicle is immobilised.

Depending on the gradient
and/or vehicle load, it may
be necessary when station-

at least a further two notches and
engage a gear (1

ary to apply the brake by

st

or reverse gear).

Power-assisted steering

With the engine running, do not leave
the steering wheel at full lock while sta­tionary as this may damage the power­assisted steering pump.

With the engine switched off, or if there
is a system fault, it is still possible to
turn the steering wheel. The force re­quired will be greater.

Never switch off the igni­tion when travelling down­hill, and avoid doing so in
normal driving (assistance

is not provided).

2.11

DRIVER CORRECTION DEVICES/AIDS (1/2)

Depending on the vehicle, this is com­posed of:

– th e A BS (an ti- loc k bra kin g

system);

– emergency brake assist.

These functions are an ad-

ditional aid in the event of

critical driving conditions,

enabling the vehicle behav­iour to be adapted to suit the driving
conditions.

However, the functions do not take
the place of the driver. They do

not increase the vehicle’s limits
and should not encourage you
to drive more quickly. Therefore,

they can under no circumstances
replace the vigilance or responsibil­ity of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).

ABS (anti-lock braking
system)

Under heavy braking, the ABS prevents
the wheels from locking, allowing the
stopping distance to be managed and
keeping control of the vehicle.

Under these circumstances, the vehi­cle can be steered to avoid an obstacle
whilst braking. In addition, this system
can increase stopping distances, par­ticularly on roads with low surface grip
(wet ground etc.).

You will feel a pulsation through the
brake pedal each time the system is
activated. The ABS does not in any way
improve the vehicle's physical perform­ance relating to the road surface and
roadholding. It is still essential to follow
the rules of good driving practice (such
as driving at a safe distance from the
vehicle in front etc.).

In an emergency, apply firm and
continuous pressure to the brake
pedal. There is no need to pump
it repeatedly. The ABS will modu­late the force applied in the braking
system.

2.12

DRIVER CORRECTION DEVICES/AIDS (2/2)

Operating faults

– Warning light x lights up on the

instrument panel: the ABS is deacti­vated.

Braking safety is still guaranteed.

–

x and D are lit on the in-

strument panel, this indicates a
fault in the braking system.

In both cases, consult an approved
Dealer.

Your braking systems

are partially operational.

However, it is dangerous

it is essential to stop immediately,
as soon as traffic conditions allow.
Contact an approved dealer.

to brake suddenly and

Emergency brake assist

This system supplements the ABS
and helps reduce vehicle stopping dis­tances.

Operating principle

The system is for detecting an emer­gency braking situation. In this case,
the braking assistance immediately de­velops maximum power and may trig­ger ABS regulation.

ABS braking is maintained as long as
the brake pedal is applied.

2.13

AUTOMATIC TRANSMISSION (1/3)

1

2

Driving in automatic mode

Move lever 1 to position D.
In the majority of traffic conditions, you

will not have to touch the gear selector
lever again: the gear will be changed
automatically at the right time and at
the most suitable engine speed be­cause the automatic system takes into
account the vehicle load and road con­tour and adjusts itself to the particular
driving style you have chosen.

Selector lever 1

P: park
R: reverse
N: neutral
D: automatic mode

3: displays gear engaged in manual

mode.

For safety reasons, do not

switch off the ignition before

the vehicle has come to a

complete standstill.

2.14

3

Operation

With the gear lever in position P or N,
switch on the ignition.

With your foot on the brake pedal, move
the lever out of position P.

Only engage D or R when the vehi­cle is stopped, with your foot on the
brake and the accelerator pedal re­leased.

You must apply the brake before
pressing the unlocking button 2 to
move out of position P.

Economical driving

When driving, leave the lever in posi­tion D, keeping the accelerator pedal
lightly depressed to ensure automatic
gear changes at comparatively low
engine speeds.

Accelerating and overtaking

Depress the accelerator pedal firmly
and fully (so that it goes beyond the
kickdown point).

This will enable you to change down
to the optimum gear within the
engine range.

AUTOMATIC TRANSMISSION (2/3)

Special cases

1

4

In certain driving conditions (e.g.: to
protect the engine) the “automated
system” may change the gear automat­ically.

Likewise, to prevent incorrect manoeu­vres, a gear change may be refused by
the automatic system: in this case the
gear display flashes for a few seconds
as a warning.

5

Driving in manual mode

With selector lever 1 in position D,
move the lever to the left.
Shifting the lever repeatedly allows you
to change gears manually:

– To move down through the gears,

push the lever backwards;

– to move up through the gears, push

the lever forwards.

The gear selected is displayed on the
instrument panel.

Special circumstances

– Snow position: if you are driving on

ground where you are likely to skid
(snow, mud, etc.), press switch 4
and operating tell-tale 5 will come
on.

Once these special driving con­ditions no longer apply, exit this
function by pressing switch 4
again. Operating tell-tale light 5
goes out.

2.15

AUTOMATIC TRANSMISSION (3/3)

– If the road contour and bends in

the road do not allow you to stay in

automatic mode (e.g.: in mountain­ous areas), it is recommended that
you switch to manual mode.
This will prevent the automatic gear­box from changing gears repeatedly
when climbing, and permit engine
braking on long descents.

– In cold weather, start the engine

and wait a few seconds before
moving the selector lever from posi­tion P or N and engaging it in D or R
to prevent the engine stalling.

– Vehicles not fitted with traction

control: on a slippery surface or
surface with a low level of adhesion,
change to manual mode and select
second gear (or even third) before
starting the engine to avoid wheel­spin when accelerating.

In very cold weather, the system
may prevent the gears from being
shifted in manual mode until the
gearbox reaches the right tempera­ture.

Parking the vehicle

When the vehicle is stopped, move the
lever to position P while keeping your
foot on the brake pedal: the gearbox is
in neutral and the drive wheels are me­chanically locked by the driveshaft.
Apply the handbrake.

For safety reasons, do not
switch off the ignition before
the vehicle has come to a
complete standstill.

An impact to the under­side of the vehicle while
manoeuvring (e.g.: strik-

ing a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: defor­mation of an axle).

To avoid any risk of accident, have
your vehicle checked by an ap­proved Dealer.

2

6

Operating faults

If a vehicle with an automatic gear­box breaks down, please refer to the

information on “Towing” in Section 5.
When setting off, if the lever is locked
in position P even though you are
pressing the brake pedal, the lever can
be released manually. To do this, unclip
the base of the lever, press recess 6,
visible on the gear lever gaiter, and the
unlocking button 2.

2.16

Section 3: Your comfort

Air vents, air outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2

Heating, Ventilation, Air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4

Manual air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6

Air conditioning: information and advice on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9

Interior lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10

Electric windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11

Sun visor, Grab handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13

Ashtrays, Cigarette lighter, Accessories socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14

Passenger compartment storage space and fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15

Rear headrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.17

Rear bench seat: functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.18

Luggage compartment, Transporting objects in the luggage compartment . . . . . . . . . . . . . . . . . . . 3.19

Roof bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.20

Rear parcel shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.21

3.1

AIR VENTS, air outlets (1/2)

1 2 3 76

1 Left-hand side air vent

2 Left-hand side window demister

vent

3 Windscreen demisting vents

4 Centre air vents

5 Control panel

4

9

5

88

9

6 Right-hand side window demister

vent

7 Right-hand side air vent

8 Front passenger footwell heater

outlets

9 Rear passenger footwell heater

outlets (depending on the vehicle)

3.2

AIR VENTS, air outlets (2/2)

10 10

11

12

To remove bad odours from your ve­hicles, only use the systems designed
for this purpose. Consult an approved
Dealer.

Centre and side air vents

Air flow

To open air vent 10 or 12, press on the
air vent (point 11) until it is open as far
as required.

Direction

To direct the air flow, swivel air vent 10
or 12.

Do not add anything to the
vehicle’s ventilation circuit
(for example, to remove
bad odours).

There is a risk of damage or of
fire.

3.3

HEATING, VENTILATION, AIR CONDITIONING (1/2)

Air conditioning controls

(depending on vehicle)

Button B switches the air conditioning
on or off.

The system cannot be switched on if
control C is set to 0.

CB

Using the air conditioning system ena­bles you to:

– lower the internal passenger com-

partment temperature, especially in
hot weather, when driving in traffic or
when the vehicle has been parked in
the sun;

– reduce the humidity of the air blown

into the passenger compartment (re­moval of condensation).

Fuel consumption increases when the
air conditioning system is being used
(switch it off when it is not required).

Note: The air conditioning may be used
in all conditions but does not operate
when the external temperature is low.

– Button B not activated (warning

light off).

The air conditioning is not operating.
The heating and ventilation controls
are the same as a vehicle without air
conditioning.

– Button B activated (warning light

on).

The air conditioning is operating.

3.4

HEATING, VENTILATION, AIR CONDITIONING (2/2)

B

In very hot weather or when the vehicle
has been parked in the sun, open the
doors for a few moments to let the hot
air escape before starting the engine.

Use the passenger compartment isola­tion function to lower the temperature
as quickly as possible to the required
comfort level. Switch off the air recircu­lation function once a comfortable level
has been reached.

F

When the air conditioning system is op­erating, all windows must be closed for
maximum efficiency.

If there is an operating fault, contact an
approved dealer.

If no cold air is produced

Check that the controls are set correctly
and that the fuses are sound. If they are
not, switch off the heating and air condi­tioning system (warning light integrated
into button B) and contact an author­ised dealer.

Adjusting the air temperature.

Move control F to obtain the desired
temperature. The further the control is
in the red, the more the temperature will
be increased.

Do not open the refrigerant

fluid circuit. The fluid may

damage eyes or skin.

3.5

MANUAL AIR CONDITIONING (1/3)

Controls

A Adjusting the distribution of air in the

passenger compartment.

B Air conditioning button (depending

on vehicle).

C Adjusting the ventilation speed.
D Air recirculation and isolation of the

passenger compartment.

E Heated rear screen and demister

and heated door mirror button (de­pending on vehicle).

F Adjusting the air temperature.

FA B C D E

Information and advice for use:

Please see the information on “Air con­ditioning: information and advice on
use”.

Distribution of air in the
passenger compartment

Turn control A.

W

All the air is then directed to the wind­screen and front side window demister
outlets.

i

front side window demisting vents, the
windscreen demisting vents and the
footwells.

F

Close the dashboard vents
for more effective demisting.

The air flow is distributed be­tween all the air vents, the

The air flow is directed mainly
towards the footwells.

3.6

MANUAL AIR CONDITIONING (2/3)

G

footwells.

J

This selection is not appropriate if all
the air vents are closed.

The air flow is directed towards
the dashboard vents and the

All the air flow is directed to the
dashboard vents.

EC

Rear screen de-icing/
demisting

With the engine running, press
button E, the operating warning light for
the button will come on.

This function permits rapid demisting/
de-icing of the rear screen and de-icing
of the door mirrors (on equipped vehi­cles).

To exit this function, press button E
again.

Demisting automatically stops by de­fault.

y

Turn control C from 0 to 4.
The passenger compartment is ven-

tilated by blown air. The blower deter­mines how much air enters but vehicle
speed has a slight effect on this.

The further the control is positioned to
the right, the greater the amount of air
blown into the passenger compartment.

ventilation speed

Adjusting the

3.7

MANUAL AIR CONDITIONING (3/3)

D

Air recirculation operation
(isolation of the passenger
compartment)

(depending on vehicle)

Turn control D towards air recirculation
symbol

In these conditions air is taken from the
passenger compartment and is recircu­lated, with no air being taken from out­side the vehicle.

â.

Air recirculation is for:

– isolating the vehicle from the exter-

– bringing the passenger compartment

Prolonged use of this position (iso­lation mode) may mist up the win­dows slightly or cause odours due
to the air not being renewed.
It is therefore advisable to return to
normal operation (external air) by
pressing control D when you have
passed through the polluted area.

nal atmosphere (driving in polluted
areas, etc.);

to the desired temperature as quickly
as possible.

3.8

AIR CONDITIONING: information and advice on use

Fuel consumption

You will normally notice an increase
in fuel consumption (especially
when driving in town) when the air
conditioning is operating.

For vehicles fitted with air condition­ing with no automatic mode, switch
off the system when it is not re­quired.

Advice for reducing consumption
and helping to preserve the envi­ronment

Drive with the air vents open and
the windows closed.

If the vehicle has been parked in
the sun, open the doors for a few
moments to let the hot air escape
before starting the engine.

Maintenance

Refer to the Maintenance Service
Booklet for your vehicle for the in­spection frequency.

Operating faults

As a general rule, contact your ap­proved dealer in the event of an op­erating fault.

– Reduction in de-icing, demist-

ing or air conditioning per­formance.

This may be caused by the pas­senger compartment filter car­tridge becoming clogged.

– No cold air is being produced.

Check that the controls are set
correctly and that the fuses are
sound. Otherwise, switch off the
system.

Presence of water under the ve­hicle. After prolonged use of the air

conditioning system, it is normal for
water to be present under the vehi­cle. This is caused by condensation.

Do not open the refriger­ant fluid circuit. The fluid

may damage eyes or skin.

3.9

INTERIOR LIGHTING

1

Courtesy light

Pressing switch 1 provides:
– continuous lighting;
– or temporary lighting by opening one

of the front doors, or by opening one
of the four doors, depending on the
vehicle. The light only goes out when
the doors are correctly closed;

– no lighting.

Automatic operation of interior
lighting (depending on the vehi­cle)

– if the doors are unlocked using

the remote control, the lighting
is switched on for approximately
30 seconds.

– if a door is open (or not properly

closed), the lighting is switched
on for approximately 30 minutes.

– if all the doors are closed, the

lighting start to dim when the ig­nition is switched on.

2

Map reading light

(depending on the vehicle)

Pressing switch 2 provides:
– continuous lighting;
– no lighting.

3.10

ELECTRIC WINDOWS (1/2)

1

2

Front electric windows

(depending on vehicle)
With the ignition on, press the bottom

of switch 1 or 2 to open the window or
press the top of switch 1 or 2 to close it.

Avoid resting any objects against a
half-open window: there is a risk that
the electric window winder could be
damaged.

3

4

Rear electric windows

(depending on vehicle)
With the ignition on, press switch 3

or 4 to open the window or raise
switch 3 or 4 to close it.

5

Locking and unlocking the
rear window controls

Press the top of switch 5 to lock the op­eration of the rear electric windows or
on the bottom of switch 5 to unlock it.

3.11

ELECTRIC WINDOWS (2/2)

6

Manual window winder
controls

Turn handle 6 to lower or raise the
window to the desired height.

Safety of rear occupants

The driver can inhibit opera-

tion of the rear electric win-

dows by pressing switch 5.

Driver’s responsibility

Never leave your vehicle with the
key or remote control inside and
never leave a child (or a pet) un­supervised, even for a short while.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
doors. If any part of the body be­comes trapped, reverse the direc­tion of the window immediately by
pressing the relevant switch.

Risk of serious injury.

3.12

SUN VISOR/GRAB HANDLE

3

1

2

4 5 6

7

Sun visor

Pivot sun visor 1 or 5 against the wind­screen.

OR
Unclip the sun visor from its mount-

ing 3 or 4 and pivot it against the door
window.

Sun blind storage compartment 2

This can be used for storing motorway
tickets, cards, etc.

Vanity mirror
(depending on the vehicle)

The passenger sun blind is fitted with
a courtesy mirror 6 on the passenger
side.

Grab handle 7

This offers support and can be held
when the vehicle is being driven.

Do not use it for getting into or out of
the vehicle.

3.13

ASHTRAYS/CIGAR LIGHTER/ACCESSORIES SOCKET

Ashtray

2

It can be housed in either position 2
or 4.

Lift cover 3 to open.
Remove the ashtray to empty it.

1

3

4

Cigar lighter 1

With the ignition on, push in the cigar
lighter 1.

It will spring back with a click when it is
ready. Pull it out to use. After use, re­place it without pushing it all the way in.

OR

Accessories socket 1

It is provided for connecting acces­sories approved by our Technical
Department with a maximum power of
120 Watts (12 V).

3.14

Connec t accessor i e s

with a maximum power of

120 Watts only.

Fire hazard.

If your vehicle is not fitted with a
cigar lighter and an ashtray, these
can be obtained from an approved
Dealer.

PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/2)

1

A

2

Passenger side glove box

Pull handle 1 to open it.

Nothing should be placed
on the floor area in front of
the driver as such objects

may slide under the pedal
during braking manoeuvres, thus
obstructing its use.

This glove box can be used to store A4
format documents.

Inside the cover, there are two storage
spaces for pens and maps.

Precautions during use

Cover A in the bottom of the glove
box protects a socket reserved ex­clusively for operations by the ap­proved dealer network

You should therefore avoid keeping
liquids in this compartment (there is
a risk of liquid leaking and getting
into this socket).

Storage compartment 2

(or passenger air bag location)

Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage

compartments in such a
way that they may fall onto passen­gers during sudden turning, braking
or in the event of an accident.

3.15

PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/2)

3

4

5

Centre console storage
compartment 3

(or radio location)

Nothing should be placed
on the floor area in front of
the driver as such objects

may slide under the pedal
during braking manoeuvres, thus
obstructing its use.

3.16

Front door storage
compartments 4

Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage

compartments in such a
way that they may fall onto passen­gers during sudden turning, braking
or in the event of an accident.

Front seat storage
compartments 5

REAR HEADRESTS

A

B

A

1

2

3

1

Adjusting the height of the
headrests A

Press the tab on catch 1 on each of the
rods on headrest A and simultaneously
slide the headrest.

To remove the headrests A

Press the tabs on the catches 1 and 4
and remove the headrest.

Child headrest storage position B
(depending on the vehicle)

When the headrest is set at the
lowest position, this is for storage
only. It should not be in this position

when a seat is occupied.

A

A

B

4

4

To remove headrest B

Simultaneously press the tabs on
catches 2 and 3 on each of the head­rest rods, then remove the headrest.

Position for using headrest B

Raise the headrest to the upper stop
to use it in the high position. Press the
tabs on the catches 2 and 3 and lower
the headrest completely.

To refit headrests A and B

Insert the rods into the holes, press the
tabs on both rods and lower the head­rest.

The headrest is a safety
component. Ensure that it is
fitted and in the correct po-

sition: the top of your head
should be in line with the top of the
headrest.

3.17

REAR BENCH SEAT: functions

1

2

3

To fold down the seatback

Remove the rear headrests (if fitted).
Lower handle 1.
Lower seatbacks 2 and 3.

When moving the rear
bench seat, make sure the
anchorage points are clean
(they should be free from

grit, cloths, toys etc.).

To reposition the seatback

Raise the seatbacks.
Check the seatbacks are correctly

locked in position.

Check that the rear seat
belts are positioned and
operating correctly each
time the rear bench seat is

moved.

For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.

– When retur ning the

seatback to its normal
position, make sure that

it is properly locked at the
top.

– If seat covers are fitted, make

sure these do not prevent the
seatback latch from locking in.

– When moving the bench seat,

ensure the seat belt unit buck­les do not cross over and ensure
they are correctly repositioned
before folding down the seat
base.

Once the bench seat has been re­turned to its normal position, check
that the seat belts are correctly po­sitioned. The seat belts must be on
the seatback.

3.18

LUGGAGE COMPARTMENT, TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT

Transporting objects in the
luggage compartment

Always position the objects transported
so that the largest surface is against:

– The back of the rear bench seat, for

normal loading.

2

1

– The front seats for maximum loads.
Ensure that the load is evenly distrib-

uted over the largest possible loading
surface to prevent damage to the ve­hicle.

Manual control

To open, insert the key in the lock and

turn it clockwise.
Remove the key and press button 1.

Lift the luggage compartment lid.
To close, push the luggage compart­ment lid downwards. Insert the ignition
key in the lock and turn it anticlockwise.

Always position the heaviest items directly on the floor. Use the lashing points on the luggage compartment floor, if
these are fitted to the vehicle. The luggage should be loaded in such a way that no items will be thrown forward and
strike the occupants if the driver has to brake suddenly. Fasten the rear seat belts, even if the seats are not occupied.

Electric central locking

The tailgate is locked and unlocked at
the same time as the doors.

To open, press button 2 and lift the tail-
gate.

To close, push the luggage compart­ment lid downwards.

3.19

ROOF BARS

3

1

2

Access to the mounting
points

(depending on the vehicle)
Open the doors. Behind seal 2 are

blanking bolts 1 which protect the
mounting bolt locations.

When fitting roof bars, replace the
blanking bolts with the mounting bolts
supplied with the roof bars.

Never remove blanking
bolts 1 without plugging the
holes afterwards.

Roof bars 3

(depending on the vehicle)
Luggage can be transported on the roof
rack mounted on the roof bars.

Once they are secured on
to the vehicle, the mount­ing bolts should never be

removed (risk of damag­ing the vehicle). Only bolts supplied
originally with the roof bars should
be used to fit the roof bars onto the
vehicle.

For information on the range of
equipment adapted to your ve­hicle, we advise you to consult
an approved Dealer. Refer to the
manufacturer’s instructions for in­formation on how to fit and operate
the equipment.

Please keep these instructions with
the rest of the vehicle documenta­tion.

Maximum permissible load on
roof rack: refer to the information

on “Weights” in Section 6.

3.20