CycleOps 400 PRO, 200 PRO, 100 PRO, 300 PRO User Manual
CycleOps Pro Series Indoor Cycles
User Guide
400 Pro
300 Pro
200 Pro
100 Pro
Deutsche Anweisungen www.cycleops.com/userguide
Istruzioni italiane www.cycleops.com/userguide
Nederlandse instructies www.cycleops.com/userguide
Norsk instruksjoner www.cycleops.com/userguide
TABLE OF CONTENTS
CHAPTERS:
1. BEFORE BEGINNING................................................................................1
2. UNPACKING THE CYCLEOPS PRO SERIES INDOOR CYCLE............2
3. INDOOR CYCLE ASSEMBLY....................................................................3
Attach Stabilizer Feet
Attach Handlebar
Attach Seat
Level the Indoor Cycle
Attach Pedals
4. GENERAL USE............................................................................................6
Adjust Seat
Adjust Handlebar
Adjust Resistance
5. COMMON ADJUSTMENTS.....................................................................8
Replace Speed Sensor Battery
Replace Cadence Sensor Battery
Replace Hub Batteries
Adjust Flywheel/Chain Tension
Adjust Brake Pad
6. PREVENTATIVE MAINTENANCE.........................................................10
7. ELECTRONICS.........................................................................................11
8. RADIO FREQUENCY (RF) INTERFERENCE........................................12
9. IMPORTANT PRECAUTIONS................................................................12
10. WARRANTY............................................................................................13
CHAPTER 1: bEfoRE bEginning
Congratulations on choosing the CycleOps Pro Series indoor cycle! The CycleOps Pro Series indoor cycle takes cycling to the next
level as the only indoor cycle to fit, feel and ride like an outdoor bike.
CycleOps Pro Series Indoor Cycle User Guide for:
-400 Pro
-300 Pro
-200 Pro
-100 Pro
Read this guide to learn how to:
-Assemble the indoor cycle
-Use the indoor cycle
-Make common adjustments
Visit www.cycleops.com to learn more about Saris Cycling Group and the CycleOps Pro Series indoor cycle:
-Register product for warranty
-View frequently asked questions
-View instructional videos
-View product and technical updates from CycleOps
-Sign up for CycleOps Power newsletter
-Learn more about training with power
1
CHAPTER 2: UnPACking THE CyClEoPs PRo sERiEs indooR CyClE
Place the box upright and cut the plastic binding straps. Lift the top of the box to expose the indoor cycle and packaging.
Remove all parts from the box including foam inserts. Ensure all the following parts are included:
Name Quantity
A Rear stabilizer 1
B Front stabilizer 1
C Main frame assembly 1
D Handlebar post (shorter, reads to 18”) 1
E Seat post (longer, reads to 23”) 1
F Seat 1
G Seat post clamp 1
H Handlebar 1
I Water bottle holder 1
J End caps 2
K End cap screws 4
L Water bottle spacer 1
M Large L handles 2
N Small L handles 2
O Stabilizer bolts 8
P Stabilizer washers 8
Q Multi-purpose wrench 1
R 6mm Allen wrench w/Phillips screw-
driver end
S 5mm Allen wrench 1
T 4mm Allen wrench 1
U 3mm Allen wrench 1
1
Rear stabilizer
Handlebar
post
Seat post
clamp
End caps
A
D E
18”
G
J
Front stabilizer
Seat post
Handlebar
End cap screws
B
H
K
Main frame assembly
Seat
23”
Water bottle
holder
Water bottle
spacer
C
F
I
L
Additional tools that may be helpful:
-Vice Grips or small clamping tool
-17mm Cone wrench
-15mm box wrench
-10mm box wrench
-Pliers
-Pedal wrench
-2.5mm Allen wrench
Large L Handles
Stabilizer bolts
M
O
6mm Allen wrench w/
Phillips screwdriver end
5mm Allen wrench
4mm Allen wrench
3mm Allen wrench
Small L Handles
Stabilizer washers
N
P Q
Multi-purpose
wrench
R
S
T
U
2
CHAPTER 3: indooR CyClE AssEmbly
Attach Stabilizer Feet
Rear stabilizer
A
Front stabilizer
B
1. Note the difference between the front
and rear stabilizers. The larger stabilizer
with wheels goes in the rear of the indoor
cycle (under the fl ywheel).
Attach Handlebar
C
Main frame
assembly
Rear stabilizer
A
A
2. Attach the rear stabilizer to the rear of
the main frame with four 5mm stabilizer
bolts and stabilizer washers using the
5mm Allen wrench. Tighten the inner
bolts fi rst, and then proceed to the outer
bolts to ensure the foot is secured properly and evenly.
Handlebar post
D
M
Large L
handle
Front stabilizer
B
3. Attach the front stabilizer to the front
of the main frame with four 5mm stabilizer bolts and stabilizer washers using
the 5mm Allen wrench. Tighten the
inner bolts fi rst, and then proceed to the
outer bolts to ensure the foot is secured
properly and evenly.
Handlebar
Water bottle
spacer
Water bottle holder
1. Remove 6mm bolt in main frame assembly using 6mm Allen wrench. The
6mm bolt can be kept in place of the
large L handle for a more permanent
placement of the handlebar height.
Handlebar
Water
bottle
spacer
Water
bottle
holder
4. Secure the water bottle holder and
handlebar together using the previously
removed, two 4mm spacer bolts and
washers, on the underside of the handlebar.
2. Insert the handlebar post into the head
tube and secure it by inserting the large L
handle into the main frame assembly on
the right side of the indoor cycle (chain
guard side).
Handlebar post
Handlebar
End cap
5. Carefully slide the road style handlebar
assembly onto the handlebar post.
Secure the plastic end cap to the
handlebar post using two end cap screws
with the Phillips screwdriver side of the
6mm Allen wrench.
3. Slide the water bottle holder and water
bottle spacer onto the road style handlebar.
Small L
handle
6. Once the road style handlebar is in
place, secure it with the small L handle on
the right side of the indoor cycle (chain
guard side).
3
Large L
handles
Push
M
Small L
handles
N
Rotate
7 Push black button and rotate handle on
small and large L handles to position the
handle without tightening. Release the
button and allow the handle to seat to
tighten or loosen an adjustment.
Attach Seat
A seat has been included with the CycleOps Pro Series indoor cycle. If desired, the indoor cycle can accommodate an off-the-shelf
seat to personalize the fit, feel and ride. In some instances, a shorter seat post clamp is required for individuals under five feet tall.
If desired, contact Saris Cycling Group to purchase the short seat clamp.
Main frame
assembly
C
1. Remove 6mm bolt in main frame assembly using 6mm Allen wrench. The
6mm bolt can be kept in place of the
large L handle for a more permanent
placement of the seat post height.
Main frame
assembly
Seat post
C
E
Large L
handle
M
2. Insert seat post into the seat tube and
secure it by inserting the large L handle
into the main frame assembly on the
right side of the indoor cycle (chain
guard side).
Seat post
E
Seat post
clamp
Small L
handle
G
N
3. Attach the seat post clamp to the seat
post. Once the seat is level, properly
tighten with the small L handle.
4
Loading...