How it Works
Cub cadet
Loading...
HT59L
User Manual
12 pgs4.48 Mb0
Maintenance Manual
2 pgs278.41 Kb0

Cub cadet HT59L User Manual

• IMPORTANT SAFETY INSTRUCTIONS •
769-06500 P01 01/11
Operator’s Manual
20 Volt Lithium-Ion
Battery-Powered Hedge Trimmer
HT59L
TABLE OF CONTENTS
Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.
For assistance regarding the assembly, controls, operation or maintenance of the unit, please call the Customer Support Department. Additional information about the unit can be found on our website.
Please call the Customer Support Department for replacement parts. When servicing, use only identical replacement parts.
DO NOT RETURN THIS
PRODUCT
Please call the Customer Support Department
or visit our website for assistance:
or
SAFETY INFORMATION
SAVE THESE INSTRUCTIONS
All information, illustrations and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.
Copyright© 2011 MTD SOUTHWEST INC, All Rights Reserved.
Use 20V Lithium-Ion Battery A59 LBTY (sold separately) Use 20V Lithium-Ion Battery Charger A59LCHGR (sold separately)
SERVICE INFORMATION
PRELIMINARY SAFETY PRECAUTIONS
• DO NOT rely exclusively upon the safety devices built into the unit.
• Keep bystanders, especially children and pets, at least 50 feet (15 m) away. If anyone enters the work area, stop the unit!
• Keep the work area clean. Cluttered areas invite injuries. Do not start the operation until the work area is clear and free from obstructions and there is secure footing.
• Always wear appropriate eye and ear protection when operating this unit. Wear safety goggles, or safety glasses with side shields, that are marked as meeting ANSI Z87.1-1989 standards. Failure to do so could result in serious eye injury caused by thrown objects. If the operation is dusty, wear a facemask or dust mask.
• Dress appropriately, wear heavy, snug-fitting clothes (long pants and a long sleeve shirt), non-slip protective gloves and boots. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level to prevent entanglement in moving parts.
• Only use the unit in daylight or good artificial light.
• Only use the unit for the purpose intended.
HEDGE TRIMMER SPECIFIC SAFETY PRECAUTIONS
• DO NOT over reach.
• DO NOT cut above shoulder height.
• Inspect the work area before using the unit. Remove any hard and/or sharp objects, such as glass, wire, etc. If thrown or caught in the trimmer blade, such objects could cause property damage or injury to the operator or bystanders.
• Grip the unit firmly with both hands when the motor is running. Keep the left hand on the front handle and the right hand on the rear handle. Use a firm grip with thumbs and fingers encircling the handles. Stand slightly to the left of the unit to avoid being in the direct line of the trimmer blade. Follow all instructions in the Operating Instructions section.
• Never grip the unit by the guard or use the guard as a handle.
• Always begin a cut with the motor running at full speed. Fully squeeze the switch trigger and maintain a steady cutting speed.
• Follow the manufacturer’s sharpening and maintenance instructions for the trimmer blade.
OTHER SAFETY PRECAUTIONS
• DO NOT operate the unit with one hand! Serious injury to the operator, helpers or bystanders may result from one-handed operation. This unit is intended for two-handed use.
• DO NOT handle the unit with wet hands.
• DO NOT
operate the unit on unstable surfaces, such as trees, ladders, slopes or rooftops. Be very
careful when using the unit on stairs.
• DO NOT expose the unit to rain. Do not use the unit in damp or wet locations or conditions.
• DO NOT
operate the unit on wet surfaces.
• DO NOT use the unit in the presence of flammable liquids or gases.
• DO NOT operate a unit that is damaged, improperly adjusted or not completely and securely assembled. Be sure that the unit stops when the trigger is released. Do not use the unit if the switch does not turn the unit on and off properly or if the switch lock does not work.
• DO NOT attempt operations beyond the operator’s capacity or experience.
• DO NOT cut near electrical cables or power lines.
• DO NOT force the unit. It will do a better, safer job when used at the intended rate.
• To reduce the risk of electric shock, avoid body contact with grounded conductors, such as metal pipes or wire fences.
• Keep proper footing and balance at all times.
• Use extreme caution when reversing or pulling the unit back toward the operator.
• If the unit produces excessive vibration, stop the motor immediately. Inspect the unit for loose screws, bolts, nuts, etc. or damaged parts. Tighten or replace any loose or damaged parts before resuming operation.
• Keep all body parts away from the trimmer blade when the motor is operating. Before starting the unit, make sure the trimmer blade is not contacting anything.
READ ALL INSTRUCTIONS BEFORE OPERATING
SAFETY BASICS
• Carefully read and understand the operator's manual of the battery that powers this unit.
• Be thoroughly familiar with the controls and the proper use of the unit. Know how to stop the unit and disengage the controls quickly.
• Stay alert! Do not operate the unit when tired, ill or under the influence of alcohol, drugs or medication.
• Never allow children to operate the unit. Never allow adults to operate the unit without proper instruction.
• Do not allow the unit to be used as a toy.
• Make sure that all guards and safety attachments are properly installed before operating the unit.
• Keep these instructions. Refer to them often and use them to instruct other users. If loaning someone this unit, also loan them these instructions.
WARNING:
Please read the entire operator’s manual carefully before attempting to assemble, operate or maintain the unit. Follow all safety instructions. Failure to do so can result in property damage or serious injury to yourself and/or others.
U.S.
1-877-282-8684
www.cubcadet.com
Canada
1-800-668-1238
www.cubcadet.ca
CALIFORNIA PROPOSITION 65
WARNING:
Battery posts, terminals and certain finished components contain lead, lead compounds and chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
DANGER:
Signals an EXTREME hazard.
Failure to obey a safety DANGER signal WILL result in serious injury or death to yourself or to others.
WARNING:Signals a SERIOUS hazard.
Failure to obey a safety WARNING signal CAN result in serious injury to yourself or to others.
CAUTION:
Signals a MODERATE hazard.
Failure to obey a safety CAUTION signal MAY result in property damage or injury to yourself or to others.
IMPORTANT! Signals special mechanical information. NOTE: Signals additional important general information.
SYMBOL MEANING
• SAFETY ALERT SYMBOLS •
Safety alert symbols are used to draw your attention to possible dangers. These symbols, and their
explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures. These safety instructions are not meant to cover every
possible condition that may occur. If questions arise, please call the Customer Support
Department at 1-877-282-8684 (U.S.) or 1-800-668-1238 (Canada).
SAFETY INFORMATION
2
• SAFETY AND INTERNATIONAL SYMBOLS •
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating, maintenance and repair information.
• SAFETY ALERT SYMBOL
Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.
• READ OPERATOR'S MANUAL
WARNING:R
ead the operator’s manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.
• WEAR EYE AND HEARING PROTECTION
WARNING:Thrown objects and loud noise can cause severe eye
injury and hearing loss. Wear eye protection meeting ANSI Z87.1-1989 standards and ear protection when operating this unit. Use a full face shield when needed.
• KEEP BYSTANDERS AWAY
WARNING:Keep all bystanders, especially children and pets, at
least 50 feet (15 m) from the operating area. If anyone enters the work area, stop the unit!
SYMBOL MEANING
• WEAR SAFETY FOOTWEAR
Wear non-slip safety footwear when using this equipment.
•
WEAR SAFETY GLOVES
Wear non-slip, heavy-duty protective gloves when handling the unit.
• DO NOT USE IN THE RAIN
WARNING:Avoid dangerous environments. Never operate your
unit in the rain or in damp or wet conditions. Moisture is a shock hazard.
• Always stop the motor when operation is delayed, before setting down the unit or when walking from one location to another. Make sure the blade comes to a complete stop.
•
To avoid accidental starting, never carry the unit with fingers on the switch trigger.
•
Always carry the unit by the front handle with the battery removed, finger off the switch trigger and the
trimmer
blade
sheathed in the scabbard and positioned to the rear
•
Always make sure the switch lock is in the locked or OFF position before installing or removing the battery.
• Use extreme caution when cutting small-sized brush, as slender material may catch the trimmer blade and be whipped toward the operator or pull the operator off balance.
•
This unit is intended for infrequent use by homeowners. It is not intended for prolonged use.
MAINTENANCE AND STORAGE SAFETY
• DO NOT perform
maintenance
procedures other than those described in this manual. Do not
attempt to repair; there are no user serviceable parts inside.
• Follow all maintenance instructions in this manual.
• Before inspecting, servicing, cleaning, storing, transporting or replacing any parts on the unit:
1.
Make sure all moving parts have stopped.
2. Allow the unit to cool.
3. Make sure the switch lock is in the locked or OFF position.
4. Remove the battery.
• Never remove, modify or make inoperative any safety device furnished with the unit.
• For safer, more effective performance, make sure the trimmer blade is sharp, properly cleaned and free from obstructions.
• Frequently inspect the unit for damage.
Before further use, any damaged part should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts and any other conditions that may affect its operation. Damaged parts should be properly repaired or replaced.
• Use only original manufacturer replacement parts and accessories, which are designed specifically to enhance the performance and maximize the safe operation of the product. Failure to do so may cause poor performance and possible injury.
• Remove the battery from the unit when not in use.
• Be sure to secure the unit while transporting.
• Always use the scabbard on the trimmer blade during transportation and storage.
• When not in use, store the unit in a locked-up and dry, or high and dry, place to prevent unauthorized use or damage. Keep out of the reach of children.
•
Keep the handles dry, clean and free from debris, oil and grease. Clean the unit after each use. Never douse or squirt the unit with water or any other liquid.
Do not use solvents or strong detergents.
• If dropped in water, do not use the unit.
This unit comes completely assembled.
UNPACKING
• Carefully remove the product and any accessories from the box.
• Inspect the product carefully to make sure no breakage or damage occurred during shipping.
• Do not discard the packing material until you have carefully inspected and satisfactorily operated the product.
• If any parts are damaged or missing, please call 1-877-282-8684 (U.S.) or 1-800-668-1238 (Canada) for assistance.
INSTALLING AND REMOVING THE BATTERY
Follow these instructions in order to avoid injury and to reduce the risk of electric shock or fire:
• Verify that the switch lock is in the locked or OFF position before installing or removing the battery. Refer to Starting and Stopping Instructions.
• Verify that the battery is removed and the switch lock is in the locked or OFF position before inspecting, adjusting or performing maintenance on any part of the unit.
Installing the Battery
1. Align the tongue of the battery with the handle cavity (Fig. 1).
2. Grasp the rear handle firmly.
3. Push the battery into the handle cavity until the latch locks into place.
4.
Do not use force when inserting the battery. It should slide into position and “click.”
Removing the Battery
1. Press the latch button on the battery down and hold (Fig. 1).
2. Grasp the rear handle firmly and pull the battery out of the handle cavity.
NOTE: The battery fits into the handle cavity snugly in order to prevent accidental dislodging. It may require a strong pull to remove it.
IMPORTANT! The battery is equipped with an internal circuit breaker that will automatically shut off power to the unit if the battery is
overloaded during heavy use. Once cooled, the battery will reset itself. Follow these steps if an overload occurs:
1. Release the switch trigger and then restart the unit. Refer to Starting and Stopping Instructions.
2. The battery may need to be removed for approximately 1 minute, allowed to cool and then reinstalled.
INSTALLING AND REMOVING THE SCABBARD Installing the Scabbard
1. Grasp the rear handle firmly.
2. Slide the scabbard over the trimmer blade until it locks into place.
Removing the Scabbard
1. Grasp the rear handle firmly.
2. Squeeze both sides of the scabbard near the tip (Fig. 2) and slide the
scabbard off of the trimmer blade.
KNOW YOUR UNIT
ASSEMBLY INSTRUCTIONS
Blade Support Rod
Scabbard
APPLICATIONS
This unit may be used for the purposes listed below:
• Trimming and forming hedges, shrubs and bushes with a branch diameter of up to 1/2 of an inch (12.7 mm).
Switch
Lock
Switch Trigger
SAVE THESE INSTRUCTIONS
Rear
Handle
Front Hand
Guard
Front
Handle
Fig. 1
Tongue
Latch
Button
Handle Cavity
STARTING AND STOPPING INSTRUCTIONS
STARTING THE MOTOR
To help prevent accidental start-ups, this unit has a switch lock and switch trigger that must be used together to start the unit.
1. Fit the battery into the handle cavity (Fig. 1). Refer to Installing the Battery.
2. Press and hold the switch lock (Fig. 3). This makes the switch trigger
operational.
3. While holding the switch lock, press and hold the switch trigger.
4. Release the switch lock and continue to squeeze the switch trigger for
continued operation.
STOPPING THE MOTOR
1. Release the switch trigger.
NOTE: It is normal for the trimmer blade to coast to a stop once the switch
trigger is released.
NOTE: Upon release of the switch trigger, the switch lock will automatically
reset to the locked position.
Switch
Trigger
Fig. 3
Switch
Lock
Battery
(Sold Separately)
CAUTION:
When the battery is not installed in the unit, keep it away from paper clips, coins, keys, nails, screws or other metal objects that could make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns or a fire.
Upper Cutting Blade
Lower Blade
Fig. 2
Squeeze Both Sides
to Release the Scabbard
Scabbard
• SHARP BLADE
WARNING:The blade on this unit is sharp. To prevent serious
injury, do not touch the blade. Keep both hands away from the blade while operating the unit.
NO TOOLS REQUIRED!
3
OPERATING INSTRUCTIONS
PROPER GRIP ON HANDLES
• Hold the unit firmly with both hands. Always keep one hand on the front handle and the other hand on the rear handle.
• Maintain a proper grip on the unit whenever the motor is running. The fingers should encircle the handle and the thumb should wrap under the handlebar. This grip is least likely to be broken. Any grip in which the thumb and fingers are on the same side of the handle is dangerous because a slight kick of the unit can cause loss of control.
• Keep hands away from the trimmer blade. Keep both hands on the handles and behind the protective guard whenever the motor is running.
PROPER CUTTING STANCE
• Balance body weight securely, with both feet on solid ground.
WORK AREA PRECAUTIONS
• Keep everyone – helpers, bystanders, children and animals – at least 50 feet (15 m) away from the work area. If anyone enters the work area, stop the unit!
• Only operate the unit when visibility and light are adequate to see clearly.
• Keep the work area clean. Do not start the operation until the work area is clear and free from obstructions. Remove all cords, lights, wires, strings or other objects that could become entangled in the trimmer blade.
BASIC OPERATING PROCEDURES
IMPORTANT: Lubricate the trimmer blade before and after each use. Ignoring
this step will decrease the life of the trimmer blade and hamper operation. Refer to Maintenance and Repair Instructions.
• Use the hedge trimmer for trimming and forming hedges, shrubs and bushes with a branch diameter of up to 1/2 of an inch (12.7 mm). For larger branches, use a non-powered saw or pruning saw.
• Work slowly, while maintaining a proper grip and stance.
• Allow the unit to do the cutting. Forcing the unit through dense growth, or attempting to trim too much at one time, can cause the blade to bind and slow, reducing the cutting efficiency. Forcing the unit can also result in damage to the blade and can increase the chance of personal injury.
• When trimming new growth, use a wide sweeping action, so that stems are fed directly into the trimmer blade. Older growth will have thicker stems and will be trimmed easiest by using a sawing motion.
• Release the switch trigger as soon as the cut is completed. Allow the trimmer blade to come to a complete stop. Unnecessary wear may occur if the unit is run without a cutting load.
• After completing the cut, wait for the trimmer blade to stop before moving the unit. Always stop the motor before moving from hedge to hedge.
• If desired, use a string to help cut hedges level. Determine the desired height of the hedge, then stretch a length of string along the hedge at that height. Trim the hedge to just above the string line. Trim the side of the hedge so that it will be slightly narrower at the top. More of the hedge will be exposed when shaped this way, and it will appear more uniform.
• Do not cut from a ladder; this is extremely dangerous. Leave this operation for professionals.
• Do not cut above chest height, as a hedge trimmer held higher is more difficult to control.
Fig. 4
MAINTENANCE BASICS
Before inspecting, servicing, cleaning, storing or transporting the unit:
1. Make sure all moving parts have stopped.
2. Allow the unit to cool.
3. Remove the battery.
SHARPENING THE BLADE
The cutting blades are made from high-quality, hardened steel and with normal usage will not require sharpening. However, if the trimmer blade accidentally hits wire fencing, stones, glass, nails or other hard objects, the blade may become nicked. There is no need to remove this nick unless it interferes with the movement of the trimmer blade. If it does interfere, or if the performance of the unit has diminished due to blade dullness, have the trimmer blade sharpened by an authorized service center.
LUBRICATING THE BLADE
• For easier operation and longer blade life, lubricate the trimmer blade before and after each use.
• During use, occasionally stop the motor, ensure that the switch lock is in the locked or OFF position, remove the battery and lubricate the trimmer blade as needed.
1. Apply light machine oil along the edge of the top blade (Fig. 5).
Fig. 5
MAINTENANCE AND REPAIR INSTRUCTIONS
Cleaning Instructions
• Remove the battery from the unit.
• Use a firm-bristled, non-wire, brush to remove debris from the trimmer blade and air vents. Keep the air vents free from obstructions.
• Wipe the unit down with a damp cloth. Do not douse the unit with water. Do not use solvents or strong detergents.
• Spray the trimmer blade with corrosion inhibiting oil.
Storage Instructions
• Follow the Cleaning Instructions listed above.
• Attach the scabbard to the trimmer blade.
• Store the unit in a dry, high and/or locked location, out of the reach of children and other unauthorized persons.
WARNING:
Do not let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic
parts. These chemicals may damage, weaken and destroy plastic, which may result in serious personal injury.
SPECIFICATIONS
MOTOR*
* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at
any time without notice.
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cordless, Battery-powered
Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
Reciprocating Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3200 SPM (Strokes Per Minute)
Blade Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 inches (56 cm)
Cutting Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 inch (12.7 mm)
Weight (with Battery) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 lb 3 oz (3.7 kg)
CLEANING AND STORAGE
TROUBLESHOOTING
NOTE: For maintenance beyond the minor adjustments listed above, please call the Customer Support Department at 1-877-282-8684 (U.S.)
or 1-800-668-1238 (Canada).
THE MOTOR OPERATES SLOWLY OR WILL NOT OPERATE
CAUSE SOLUTION
The battery lacks sufficient charge Charge the battery
The trimmer blade is jammed with debris Clean the trimmer blade
ACCESSORIES (SOLD SEPARATELY)
Model #
A59 LBTY . . . . . . . . . . . . .
A59LCHGR . . . . . . . . . . . .
Description
20V Lithium-ion Battery 20V Lithium-ion Battery Charger
Part #
753-06579 . . . . . . .
753-06580 . . . . . . .
WARNING:
Before inspecting, cleaning, or servicing the unit, stop the motor, wait for all moving parts to stop, and
remove the battery. Failure to follow these instructions can result in serious personal injury or property damage.
CAUTION:
Some spray-on lubricants contain solvents and will cause some types of grease to break down. To prevent damage to the unit, only use a high-quality machine oil.
WARNING:
To avoid possible serious injury, never touch or adjust the trimmer blade while the motor is running. The
trimmer blade is very sharp; always wear protective gloves when performing maintenance to the trimmer blade.
DANGER:
If the trimmer blade gets caught on an electrical cord or wire, DO NOT TOUCH THE BLADE! IT MAY BE ELECTRICALLY LIVE AND EXTREMELY DANGEROUS. Release the trimmer in the quickest and safest way. If possible, disconnect the damaged electrical cord or wire from its power source. If that is not possible, call an electrician, electrical contractor, or the power company for assistance. Failure to heed this danger warning will cause serious personal injury or possible death.
WARNING:
Do not allow familiarity with this unit to promote carelessness. Remember that a careless fraction of a
second is enough to inflict serious injury.
WARNING:
Always wear appropriate eye and ear protection when operating this unit. Wear safety goggles, or safety glasses with side shields, that are marked as meeting ANSI Z87.1-1989 standards. Failure to do so could result in serious eye injury caused by thrown objects. If the operation is dusty, wear a facemask or dust mask. Use a hard hat or other type of safety helmet.
WARNING:
If any parts are damaged or missing, do not operate the unit until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
WARNING:
Wear non-slip gloves for maximum grip and protection. Refer to the Safety Information section for
appropriate safety equipment.
WARNING:
Do not attempt to remove cut material or hold material to be cut while the trimmer blade is moving. Do not grasp the trimmer blade when picking up or holding the unit. Make sure the battery is removed and the switch lock is in the locked or OFF position before clearing any jammed material from the trimmer blade.
4
NOTES
Loading...
+ 8 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use