Crown CTS-8200 Brochure
CTs MULTICHANNEL SERIES
CTs 8200
Architectural & Engineering Specifi cations
CTs 8200 (120 V, 60 Hz models)
The power amplifi er shall be a solid-state eight-channel model employing Multi-Mode
The amplifi er shall contain protection from shorted, open and mismatched loads, general overheating, DC, high-frequency overloads,
under/over voltage, and internal faults.
The amplifi er shall contain FIT (Fault Isolation Topology), which isolates
channel-specifi c faults and prevents them from affecting remaining
channels.
If an amplifi er channel starts to overheat, the Thermal Level Control
(TLC) circuit shall engage that channel’s input compressor in an amount
proportional to the amount of overheating, in order to generate less
heat. If the channel becomes too hot for safe operation, the channel shall
shut off, and the Thermal Indicator for that channel shall fl ash brightly
to alert the user that a state of thermal stress or overload has caused the
channel to shut down.
The front-panel control shall be a power switch.
Rear-mounted controls shall include Channel Level Controls and a Mode
Switch. The Mode Switch (used on each consecutive pair of channels)
is a four-position switch which selects among Dual 8/4 ohms, Dual 70V,
Bridge-Mono 16/8 ohms, and Bridge-Mono 100V.
The recommended load impedance in Dual mode shall be 4/8 and 25
ohms (70V). The load impedance in Bridge-Mono mode shall be 8/16
ohms and 50 ohms (100V). The amplifi er shall be safe when driving any
kind of load, including highly reactive ones.
Rear-mounted output connectors shall be one four-pole terminal strip
for every two channels with a touch-proof cover. Rear-mounted input
connectors shall be removable Phoenix-style barrier connectors for
balanced input.
The amplifi er shall be fully compatible with and shall provide appropriate
input cables and connectors for Crown® VCA-MC8 module.
Front panel indicators shall include a yellow Bridge-Mode Indicator
(one per channel pair) that illuminates when the channel pair’s Mode
Switch is set to the “Bridge” position (and fl ashes if the Mode Switch is
changed while the amplifi er is powered up, indicating that the amplifi er
must be powered off and on to reset the Mode), a green Ready Indicator
(one per channel) that illuminates when the channel is initialized and
ready to produce audio output, a green Signal Indicator (one per channel) that illuminates to indicate the presence of input signals above –40
dBu, a red Clip Indicator that illuminates when the THD of the channel’s
output signal rises to a level typically considered as the onset of
audible clipping (and illuminates during Thermal Level Control or input
overload), a red Thermal Indicator (one per channel) that fl ashes when
a state of thermal stress or overload has caused the channel to shut
down (and fl ashes in all channels if the power supply goes into thermal
overload), a red Fault Indicator (one per channel) that fl ashes when a
fault condition has occurred in the channel, and a blue Power Indicator
that illuminates when the amplifi er has been turned on and AC power is
available (and illuminates when the amplifi er shuts off due to an under/over-voltage condition on the AC mains).
®
(AB+B) output circuitry.
The power amplifi er shall meet or exceed the following performance criteria. Input sensitivity for rated output: 1.4 V. Rated output with eight channels driven in Dual mode with 0.1% THD (20 Hz to 20 kHz): 175 watts per
channel into 4 ohms; 155 watts per channel into 8 ohms, and 185 watts
per channel (70V). Rated output in Bridge-Mono mode with four channel
pairs driven at 0.1% THD (20 Hz to 20 kHz): 350 watts per channel pair
into 8 ohms; 310 watts per channel pair into 16 ohms, and 185 watts per
channel pair (100V). Signal to Noise Ratio below rated power (20 Hz to 20
kHz): 100 dB unweighted. Phase Response: ±35 degrees from 10 Hz to 20
kHz at 1 watt. Frequency Response: 20 Hz to 20 kHz, ±0.5 dB at 1 watt into
8 ohms per channel in Dual mode. Damping Factor: greater than 180 from
10 to 400 Hz. Crosstalk (below rated power, 20 Hz to 1 kHz): greater than
80 dB. Intermodulation Distortion (60 Hz and 7 kHz at 4:1, from 163 milliwatts to full bandwidth power): less than 0.05% typical. Total Harmonic
Distortion at 1 watt from 20 Hz to 20 kHz: less than 0.05%. Common Mode
Rejection (20 Hz to 1 kHz): greater than 50 dB. DC Output Offset (shorted
input): less than 5 mV. Maximum Input Level (before input compression):
+ 22 dBu rms. Power Draw at Idle (120 VAC mains, all channels in 4/8 ohm
mode): 58 watts. Power Draw at Idle (120 VAC mains, all channels in 70V
mode): 77 watts.
The amplifi er chassis shall be constructed of steel with a durable black
fi nish and shall be designed for continuously variable-speed forced-air
ventilation from the front panel to the back panel.
The dimensions of the amplifi er shall allow for 19 inch (48.3 cm) EIA
standard (RS-310-B) rack mounting. The amplifi er shall be 5.25 inches
(13.3 cm) tall, and 16.25 inches (41.3 cm) deep behind the rack-mounting
surface.
The amplifi er shall weigh 36 pounds, 6 ounces (16.5 kg).
The amplifi er shall be designated the Crown CTs 8200.
Crown International
P.O. Box 1000
Elkhart, IN 46515-1000
TEL: 574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
Specifi cations subject to change without prior notice. Latest
information available at www.crownaudio.com.
®
Crown
, Crown Audio® Multi-Mode®, and IQ System® are registered trademarks of Crown International. Printed in U.S.A.
© 2006 Crown Audio, Inc.
06/06 135005-2A
Loading...