Model Pulse M74DP
Dual power Mini Airsoft Machine Gun
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS
MANUAL BEFORE USING THIS SOFT AIR GUN
Distributed by |
|
Crosman Corporation |
|
7629 Routes 5 & 20 |
|
East Bloomfield, NY 14443 |
|
www.crosman.com |
|
1-800-724-7486 |
SAPM74DP-515 |
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR EYE PROTECTION TO PROTECT YOUR EYES.
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND
OWNERSHIP OF THIS AIRSOFT GUN.
Recommend 18 years or older to purchase. Intended for use by those 16 or older.
Please read this owner’s manual completely. Remember to treat this airsoft gun with the same respect you would a firearm. Always carefully follow the safety instructions found in this owner’s manual and keep this manual in a safe place for future use.
If you have any questions regarding your new airsoft gun, please contact Crosman Customer Service at: 1-800-724- 7486, 585-657-6161 or www.crosman.com.
1. Learning the Parts of Your New Airsoft Gun.
Learning the names of the parts of your new airsoft gun will help you to understand your owner’s manual. Use this manual to increase your enjoyment of this airsoft gun.
A. Muzzle
B. Safety
C. Trigger Guard
D. Battery Cover
E. Grip Frame
F. Vertical Feed System
G. Vertical Feed System Port
H. Trigger
2. Operating the Safety
WARNING: Keep the airsoft gun in the “ON SAFE” position until you are actually ready to shoot. Then turn the safety to the “OFF SAFE” position.
2.1 To Put the Airsoft Gun “ON SAFE”-
A.Electronic mode
•The safety is located on the left hand side of the gun behind the trigger (fig. 2)
•This airsoft gun is “ON SAFE”,when pointing to “SAFE
B Spring mode
•The safety is located on the left hand side of the gun behind the trigger (fig. 2)
•The airsoft gun is “ON SAFE” when the handle is pointing to the word “SAFE”.
Like all mechanical devices, an airsoft gun safety can fail. Even when the safety is “ON SAFE”, you should continue to handle the airsoft gun safely. NEVER point the airsoft gun at any person. NEVER point the airsoft gun at anything you do not intend to shoot.
2.2 To Take the Airsoft Gun “OFF SAFE” A. Electronic mode
Fig.
2
SEMI
SAFE |
FULL
•Locate the safety on the left hand side of the gun behind the trigger.
•Using your thumb push the safety down toward the “FULL” and HOLD. The airsoft gun is now “OFF SAFE” and ready to fire.
•You must continue to hold the safety in the “OFF SAFE” position while shooting
B. Spring Mode
•Locate the safety on the left hand side of the gun behind the trigger.
•Push the safety up to the “SEMI” positionThis will allow you to cock the gun.
•Cock the gun by pulling the bolt back. |
|
Fig. 3 |
3.Installing the batteries
•The Pulse M74DP is run on 4 AA batteries (not included).
•To install the batteries, locate the battery cover on the bottom of the grip frame.
•Slide the cover lock back and pull cover open.
•Insert 4 AA batteries as shown (fig 3).
•Close battery cover, push down and slide cover lock back into place.
4.Loading and Unloading Plastic BBs.
WARNING: Use 6 mm plastic BBs only in this airsoft gun. Use of any other ammunition can cause injury to you or damage to the airsoft gun.
4.1 Loading Plastic BBs
DO NOT re-use plastic BBs because they could possibly cause damage to your airsoft gun.
•Make sure the airsoft gun is “ON SAFE” (step 2.1)
•Point the airsoft gun in a SAFE DIRECTION
•Slide forward the hopper door (fig. 4).
•Insert up to 250 6mm plastic BBs, shaking the gun slightly to help feed the BBs down in to the chamber.
•Close the hopper door.
Fig. 4
NOTE: YOU MUST MAKE SURE THAT THE DOOR BETWEEN THE HOPPER AND THE GUN IS OPEN FOR BBS TO FEED INTO THE GUN.
WARNING: Never assume that because the airsoft gun no longer fires a BB and/or the hopper is removed, that a BB is not lodged in the barrel. Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm
4.2Unloading the Plastic BBs Unloading without firing
•Make sure the airsoft gun is “ON SAFE” (step 2.1) and pointed in a SAFE DIRECTION.
•Slide forward the hopper door.
•Turn the airsoft gun upside down.
•Gently shake until all plastic BBs have been emptied.
•Close the hopper door.
4.3Unloading by Firing
•Make sure the airsoft gun is “ON SAFE” (step 2.1) and pointed in a SAFE DIRECTION.
•Your airsoft gun is fully automatic. It will continue to fire as you hold in the trigger.
•When you are sure of your target and backstop, and the area around the target is clear take the airsoft gun “OFF SAFE” (section 2A) aim and pull the trigger to fire.
•While holding the safety in the “FULL” position, squeeze and hold the trigger for continuous fire until no more bbs are released.
WARNING: Never assume that because the airsoft gun no longer fires a BB and/or the hopper is removed, that a BB is not lodged in the barrel. Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm
5.Aiming and Firing Safely
•You and others with you should always wear eye protection designed for airsoft to protect your eyes.
•Always point your airsoft gun in a SAFE DIRECTION.
•Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit someone or something you had not intended to hit.
•DO NOT re-use plastic BBs because they could possibly cause damage to your airsoft gun.
•Your airsoft gun is designed for target shooting and is suited for both indoor and outdoor use. Always remember to place your target carefully. THINK about what you will hit if you miss the target.
•Your airsoft gun is fully automatic. It will continue to fire as you hold in the trigger.
•While holding the safety in the “OFF SAFE” position, squeeze and hold the trigger for continuous fire.
•When you are sure of your target and backstop, and the area around the target is clear, load and charge the air-
soft gun following sections 3 and 4. Take the airsoft gun “OFF SAFE” (section 2A) aim and pull the trigger to fire. NOTE: The safety must be held in position for the airsoft gun to fire.
6.Maintaining Your Airsoft Gun
•DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft gun in any way inconsistent with this manual may make it unsafe to use, cause serious injury and will void the warranty.
•If you drop your airsoft gun, check to see that it works properly before you use it again. If anything seems changed, like a shorter or weaker trigger pull, this may mean worn out or broken parts. Call Customer Service at Crosman for assistance before using your airsoft gun again.
•Occasionally shake the gun to ensure smooth BB feeding.
•Change the batteries if firing cycle becomes slow
6.1Clearing a Jam
•Never look down the end of barrel to see if a jam has been cleared.
•Make sure the airsoft gun is “ON SAFE” and pointed in a SAFE DIRECTION.
•Insert the tapered end of the cleaning rod into the barrel, with the angle toward the breech (where the magazine connects).
•CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
6.2To Clean the Airsoft gun barrel:
•Spray a cleaning patch with Crosman Nitro Lubricant oil.
•With patch on rod, insert in into barrel to clean
•Swab barrel 3-4 times
•Repeat swabbing procedure with a dry patch
•Barrel is clean when patches come out clean after dry swabbing.
7.Reviewing Safety
•Do not ever point the airsoft gun at any person. Do not ever point the airsoft gun at anything you do not intend to shoot.
•Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm.
•Always aim in a SAFE DIRECTION. Always keep the muzzle of the airsoft gun pointed in a SAFE DIRECTION.
•Always keep the airsoft gun “ON SAFE” until you are ready to shoot in a SAFE DIRECTION.
•Always check to see if the airsoft gun is “ON SAFE” and unloaded when getting it from another person or from storage.
•Always keep your finger off the trigger and out of the trigger guard until ready to shoot.
•You and others with you should always wear eye protection to protect your eyes.
•Always wear eye protection designed for airsoft over your regular glasses.
•Use 6 mm plastic BBs only.
•Do not reuse plastic BBs because they could cause possible damage to your airsoft gun.
•Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit someone or something you had not intended to hit.
•Replace the backstop if it becomes worn. Place the backstop in a location that will be safe should the backstop fail.
•Your backstop should be checked for wear before and after each use. All backstops are subject to wear and will eventually fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.
•Do not attempt to disassemble or tamper with your airsoft gun.
•DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft gun in any way may make your airsoft gun unsafe to use, cause serious injury or death and will void the warranty.
•Using unauthorized repair centers or modifying the function of your airsoft gun in any way may be unsafe and will void your warranty.
•Do not put the airsoft gun away loaded. Make sure ALL of the plastic BBs are unloaded from the airsoft gun.
•Always store this airsoft gun in a secure location.
Specifications |
|
|
|
|
|
|
|
|
|
Mechanism/Action |
Electronic or spring |
|
Overall Length |
11.75 in |
|
|
|
|
|
Caliber/Ammunition |
6mm Plastic BBs |
|
Barrel |
Smooth |
|
|
|
|
|
Reservoir |
Up to 250 6mm BBs |
|
Safety |
Lever |
|
|
|
|
|
Weight |
12 oz. (.37 kg) |
|
Velocity |
Up to 150 fps (45.72 m/s) |
|
|
|
|
|
PERFORMANCE: Many factors can affect velocity, including brand of projectile, type of projectile and barrel condition.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our friendly customer service representatives will be glad to help. You can get answers to frequently asked questions at www.crosman.com or you can contact us directly at 1-800-7AIRGUN (1-800-724-7486)
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800- 724-7486 or 585-657-6161. (International customers should contact their distributor.) DO NOT ATTEMPT TO DISASSEMBLE IT! If you take it apart you probably will not be able to reassemble it correctly. Crosman assumes no warranty responsibility under such circumstances.
For optimum performance use Crosman ammunition only. Using other than Crosman branded ammunition may cause your product to malfunction and may void your warranty.
LIMITED 30 DAY WARRANTY
This product is warranted to the retail consumer for 30 days from date of retail purchase against defects in material and workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform normal maintenance. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, OR INCIDENTAL EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to product. Package and return to Crosman Corporation, Routes 5 & 20, East Bloomfield, NY 14443.
International Customers: Please return product to your nearest distributor. If you do not know your distributor, please call 585-657-6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be preempted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.
Loading...