All about the
Use&Care
of your Refrigerator
TA B L E O F C O N T E N T S
Important Safety Instructions |
......................2 |
Features at a Glance................................... |
4 |
Installation................................................. |
5 |
Door Removal Instructions........................... |
7 |
Handle Installation...................................... |
9 |
Connecting Water Supply.......................... |
10 |
Controls................................................... |
12 |
Storage Features...................................... |
15 |
Automatic Ice & Water Dispenser............... |
16 |
Changing the Filter................................... |
20 |
Normal Operating Sounds and Sights......... |
21 |
Care and Cleaning..................................... |
22 |
Before you Call......................................... |
24 |
Major Appliance Limited Warranty.............. |
27 |
www.frigidaire.com USA 1-800-944-9044 |
www.frigidaire.ca Canada 1-800-265-8352 |
2017) (September A12515901
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Please read all instructions before using this refrigerator.
For your Safety
•DO NOT store or use gasoline, or other flammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding flammability and other hazards.
•DO NOT operate the refrigerator in the presence of explosive fumes.
•Avoid contact with any moving parts of automatic ice maker.
•Remove all staples from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture.
Definitions
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
IMPORTANT
IMPORTANT indicates installation, operation or maintenance information which is important but not hazard-related.
Installation Checklist
Doors
Handles are secure and tight
Door seals completely to cabinet on all sides
Freezer door is level across the top
Leveling
Refrigerator is level, side-to-side and tilted ¼” (6mm) front-to-back
Toe grille is properly attached to refrigerator
Cabinet is setting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Ice Maker
House water supply connected to refrigerator
No water leaks present at all connections - recheck in 24 hours
Ice maker is turned ON
Ice & water dispenser operates correctly
Front filter must be flush with filter housing (select models)
Final Checks
Shipping material removed
Refrigerator and freezer temperatures set
Crisper humidity controls set
Registration card sent in
Child Safety
Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.
Proper Disposal of your Refrigerator or Freezer
Risk of child entrapment
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators or freezers are still dangerous
– even if they will sit for “just a few days”. If you are getting rid of your old refrigerator or
2
IMPORTANT SAFETY INSTRUCTIONS
freezer, please follow the instructions below to help prevent accidents.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance recycling/disposal methods. Check with your utility company or visit www.energystar.gov/recycle for more information on recycling your old refrigerator.
Before you throw away your old refrigerator/freezer:
•Remove doors.
•Leave shelves in place so children may not easily climb inside.
• Have refrigerant removed by a qualified service technician.
IMPORTANT
CFC/HCFC Disposal
Your old refrigerator may have a cooling system that used CFCs or HCFCs (chlorofluorocarbons or hydrochlorofluorocarbons). CFCs and HCFCs are believed to harm stratospheric ozone if released to the atmosphere. Other refrigerants may also cause harm to the environment if released to the atmosphere.
If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release refrigerant, you may be subject to fines and imprisonment under provisions of environmental legislation.
WARNING
These guidelines must be followed to ensure that safety mechanisms in this refrigerator will operate properly.
Electrical information
•The refrigerator must be plugged into its own dedicated 115 Volt, 60 Hz., 15 Amp, AC only electrical outlet.The power cord of the appliance is equipped with a threeprong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician.
Avoid connecting refrigerator to a Ground Fault Interrupter (GFI) circuit. Do not use an extension cord or adapter plug.
•If the power cord is damaged, it should be replaced by an authorized service technician to prevent any risk.
•Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.
•Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.
•Performance may be affected if the voltage varies by 10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.
•Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally.
IMPORTANT
Pressing and holding the On/Off button for three seconds, located on the temperature control panel will disable your refrigerator’s cooling system, but does not disconnect the power to the LED lighting and other electrical components. To turn off power to
your refrigerator you must unplug the power cord from the electrical outlet.
Grounding type wall receptacle
Do not, under
any circumstances, cut, remove,
or bypass the grounding prong.
Power cord with 3-prong gounded plug
CAUTION
To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.
3
FEATURES AT A GLANCE
Features may vary according to model
Ice Cream Shelf |
Water Filter |
CAUTION: |
|
Ice Maker |
(Location varies by model) |
||
|
|
Do Not Remove |
|
Fixed |
|
Magnet Behind |
|
|
Dairy |
||
Door Bin |
LED Lights |
Compartment |
|
Ice |
Dairy |
||
|
|||
Container |
|
Compartment |
|
|
|
Glass Shelf |
|
Shelf |
|
Door Bin |
|
|
|
||
|
|
Glass Shelf |
|
|
|
Door Bin |
|
|
|
Deli Drawer |
|
Door Bins |
|
Fixed |
|
|
Door Bin |
||
|
|
Crisper Pan |
|
|
|
and Cover |
|
|
|
Fixed |
|
|
|
Door Bin |
|
Slide Out Basket |
Toe Grille |
|
IMPORTANT
Features not included with your refrigerator can be purchased at
www.frigidaire.com or by calling 1-800-944-9044.
4
INSTALLATION
This Use & Care Guide provides general operating instructions for your model. Use
the refrigerator only as instructed in this Use & Care Guide. Before starting the
refrigerator, follow these important first steps.
Location
•Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.
•If possible, place the refrigerator out of direct sunlight and away from the range, dishwasher or other heat sources.
•The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.
•Consider water supply availability for models equipped with an automatic ice maker. If you do not hook up water to the refrigerator, remember to turn the ice maker off.
CAUTION
Do Not install the refrigerator where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the refrigerator.
Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator.
Installation
Installation clearances
•Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:
Sides & Top |
3/8 inch |
Back |
1 inch |
NOTE
If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider.
Toe Grille Installation and Removal
To install toe grille
1Open both doors. Slide left and right sides of toe grille over lower hinges of refrigerator.
2While pushing toe grille firmly against cabinet, fasten bottom clips of toe grille to cabinet.
3Fasten top clips to cabinet.
4Close the doors. Fasten right and left side clips into groove of bottom hinge.
|
Installing Toe Grille |
|
|
1 3 |
4 |
4 |
|
|
2 |
3 |
|
|
|
|
|
|
2 |
|
|
1 |
To remove toe grille |
|
1With both doors closed, unfasten right and left side clips of toe grille from bottom hinge groove.
2Open both doors. Press firmly on top of toe grille until top of toe grille pops off.
3Pull toe grille outward toward your body and off of lower hinges.
Removing Toe Grille
1
2
1 3 2 3
5
INSTALLATION
Door Opening
NOTE
The refrigerator doors are designed to shut by themselves within a 20 degree opening.
Your refrigerator should be positioned to allow easy access to a counter or table when removing food. For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened.
Guidelines for final positioning of your refrigerator:
•All four corners of the cabinet must rest firmly on the floor.
•The cabinet should be level at the front and rear.
•The sides should tilt ¼ inch (6 mm) from front to back (to ensure that doors close and seal properly).
•Doors should align with each other and be level.
All of these conditions can be met by raising or lowering the adjustable front rollers.
To level the cabinet using the front rollers:
1Open both doors and remove the toe grille (see “Toe Grille Installation and Removal” in the “Installation” section).
2Close the doors and use a flat-blade
screwdriver or 3/8 inch socket wrench to raise or lower the front rollers.
3Ensure both doors are bind-free with their seals touching the cabinet on all four sides.
Raise
To level the doors using the adjustable lower hinge:
NOTE
Some models will not have a set screw. For those models follow steps 2 through 4.
1Before leveling either door, remove set screw that locks door height into position. (The door cannot be adjusted without set screw removed).
2If the refrigerator door is lower than the freezer door, raise the refrigerator door by turning the adjustment screw clockwise using a 7/16 inch wrench. (See illustration.)
3If the freezer door is lower than the refrigerator door, raise the freezer door by turning the adjustment screw clockwise using a 7/16 inch wrench. (See illustration.)
Door Door
Raise |
Raise |
Door |
Door |
4After leveling, verify door stop contacts lower hinge and top of door does not contact upper hinge through full movement of door (from fully closed to fully open).
5 Reinstall set screw, locking the door height.
Door Stop |
Open Door |
|
|
Flange |
Hinge |
|
|
|
Flange |
|
Set Screw |
|
(some models) |
|
Hinge |
7/16" Wrench and
3/32" Hex Key (some models)
6Replace the toe grille by fitting it into place (see “Toe Grille Installation and Removal” in the “Installation” section).
6
DOOR REMOVAL INSTRUCTIONS
Getting through narrow spaces
If your refrigerator will not fit through an entrance area, you can reduce its size by removing the doors. Check first by measuring the entrance.
Tools Necessary:
AND |
OR |
OR |
PhillipsTM Head |
Socket Wrench Set |
Top Hinge
Cover
Screw
Top
Bottom
Hinge
Screw
Hinge
Screw
1.Disconnect electrical supply.
2.Open both doors, then remove toe grille.
3.Close doors.
To Remove Refrigerator Door:
1.Remove top hinge cover screw on refrigerator door and remove cover.
2.Trace around hinge with soft lead pencil. This will make it easier to realign doors when they are replaced.
3.Remove top hinge and lift refrigerator door off bottom hinge pin. Set door aside.
4.Remove bottom hinge, if necessary.
5.Reverse this procedure to reinstall refrigerator door.
CAUTION
Be sure doors are set aside in a secure position where they cannot fall and cause personal injury.
Adjustable Wrench 3/8" Fixed Wrench
NOTE
Before you begin, press and hold the On/Off button (located on the temperature control panel) for three seconds. Remove electrical power cord from wall outlet. Remove any food from door shelves.
Cover Screw
Top
Hinge
Cover
Hinge
Screws
Top
Hinge
Door
Hinge
Assembly
Screws
7
DOOR REMOVAL INSTRUCTIONS
To Remove Freezer Door:
1.Disconnect water line coming from lower hinge of freezer door at connection located under front of freezer: Press outer ring against face of fitting, then pull to remove tube.
2.Remove top hinge cover screw on freezer door and remove cover.
3. Disconnect wiring harness connector plug at top hinge: place your thumbs on flat sides of each connector and bend both parts back and forth, then with firm grasp, pull both pieces apart.
4.Trace around hinge with soft lead pencil. This will make it easier to realign doors when they are replaced.
5.Remove top hinge, allowing wiring harness to pull through hinge and lift freezer door off of bottom hinge pin. Lay door down flat to avoid kinking water line.
6.Remove bottom hinge, if necessary.
7. Reverse this procedure to reinstall freezer door.
When both doors have been reinstalled, connect water line by inserting tube and push until mark touches face of fitting, replace toe grille and plug in electrical power cord. Turn both temperature controls to center position. Adjust settings as necessary.
To Disconnect |
Door |
1. Press outer ring against face of |
|
fitting |
|
2. Pull to |
remove tube |
To Connect
Insert tube and push until mark touches face of fitting
Water
Line
Tubing
Hinge
Assembly Screws
8
HANDLE INSTALLATION
CAUTION
Wear gloves and safety goggles and use extreme CAUTION when installing these handles. The rounded end of the handles may be sharp (some models).
IMPORTANT
To ensure proper installation of handles, please review these instructions and illustrations thoroughly prior to installing the handles.
1Remove handles from carton and any other protective packaging.
2Position freezer handle end caps over upper and lower pre-installed shoulder bolts (A) that are fastened into door, ensuring the holes for the set screws are facing towards the refrigerator door.
3While holding handle firmly against door, fasten upper and lower Allen set screws
(B) with supplied Allen wrench.
4Repeat steps 2 and 3 to install refrigerator handle. Ensure the holes for the set screws are facing towards the freezer door.
NOTE
All set screws should be tightened and sub-flush (Allen set screw should be seated just below the surface of the end cap) of handle end cap. The end caps should be drawn tight to freezer and refrigerator doors with no gaps.
Freezer |
Refrigerator |
Upper |
Upper |
End Cap |
End Cap |
Door |
Door |
Ensure Handle Set Screws are Facing Each Other with Doors Closed |
Door |
Door |
Freezer |
Refrigerator |
Lower |
Lower |
End Cap |
End Cap |
9