Page 1
®
Page 2
TABLE OF CONTENTS
MODEL NUMBER: 486.24441
SERIAL NUMBER: __________________
DATE OF PURCHASE: __________________
....................................................................
.............................................................
...................................
....................................................
............................................................
............................................................
WARRANTY
SAFETY
Page 3
ACCESSORIES AND ATTACHMENTS
REF. QTY. DESCRIPTION
A 1 Hex Bolt, 1/4-20 x 3-1/4" LG.
C 1 Hex Bolt, 5/16-18 x 1-1/2"
D 14 Hex Bolt, 3/8-16 x 1"
E 2 Carriage Bolt, 3/8 x 1-1/4"
F 2 Carriage Bolt, 5/16 x 1"
G 6 Hex Bolt, 3/8" x 1" (Thread Forming)
H 6 Carriage Bolt, 3/8" x 1"
I 2 Hex Jam Nut, 5/16-24 Thread
J 3 Nylock Hex Nut, 1/4-20 Thread
K 3 Nylock Hex Nut, 5/16-18 Thread
L 16 Nylock Hex Nut, 3/8-16 Thread
M 6 Large 1/2" Washer
N 6 3/8" Flat Washer
P 2 Cotter Pin 1/8" x 1-1/4"
Q 1 1/2" Washer
R 6 Lock Washer, 3/8"
S 2 Palnut, 3/8"
T 1 Spacer, 9/16" OD x 5/8" LG.
U 2 Spacer, 9/16" OD x 1" LG.
D
L
I
J
K
H
A B
T
U
R
E
F
C
N
Q
O
P
S
M
G
SPECIAL
USE ONLY
FULL SIZE HARDWARE CHART
Page 4
REF. QTY. DESCRIPTION
REF. QTY. DESCRIPTION
12 1 Hanger Bracket, L.H.
13 1 Hanger Bracket, R.H.
14 1 Pivot Support Bracket
15 2 Angle Support Bracket
16 1 Channel Assembly
17 1 Blade Assembly
18 1 Blade Pivot Rod
19 1 Lift Handle Tube
20 1 Lift Handle Rod
21 1 Cable
1
2
3
4
5
6
7
10
8
9
11
REF. QTY. DESCRIPTION
7 1 Blade Adjust Spring
8 1 Plastic Grip
9 1 Grip Assembly
10 2 Angle Lock Bars
11 1 Blade Pivot Shaft
REF. QTY. DESCRIPTION
1 2 Cable End Fitting
2 1 Cable Mount Bracket
3 1 Angle Lock Spring
4 2 Nylon Tie
5 1 Spring Mount Rod
6 1 Channel Pivot Pin
18
21
19
13
12
15
14
16
17
20
Page 5
ASSEMBLY
your tractor does not have a mower deck suspension
MOWER DECK
SUSPENSION
BRACKET
Not all of the supplied parts and hardware will be
Right hand (RH) and left hand (LH) are
begin assembling until
REMOVE
BROWNING
SHIELD
5/16" NYLOCK
NUT (K)
3/8" NYLOCK
NUT (L)
5/16" x 1"
CARRIAGE
BOLT (F)
ENGINE
MOUNTING
PLATE
1/2" LARGE
WASHER (M)
(IF NEEDED)
3/8" x 1" CARRIAGE
BOLT (H)
•
Reinstall the browning shield before using your
on
Page 6
FRONT SUSPENSION
BRACKET
FRONT SUSPENSION
BRACKET
REMOVE BOLTS FROM THESE HOLES
FRONT
SUSPENSION
BRACKET
3/8" x 1"
HEX BOLT (D)
3/8" LOCK
WASHER (L)
3/8" FLAT
WASHER (N)
1/2" LARGE
WASHER (M)
R.H. HANGER
BRACKET
Repeat for the left side.
REMOVE BOLTS FROM
THESE HOLES
FRONT
SUSPENSION
BRACKET
Page 7
Use special 3/8" x 1" thread forming bolts (G) in any
3/8" x 1" HEX BOLT (D)
(OR THREAD FORMING
BOLT (G) IF NEEDED)
3/8" LOCK
WASHER (R)
3/8" FLAT
WASHER (N)
3/8" NYLOCK NUT (L)
(IF NEEDED)
R.H. HANGER
BRACKET
3/8" x 1"
HEX BOLT (D)
3/8" NYLOCK
NUT (L)
PIVOT SUPPORT
BRACKET
3/8" x 1"
HEX BOLT (D)
3/8" NYLOCK
NUT (L)
ANGLE SUPPORT
BRACKET
the 4 bolts fastening the angle support
the 4 bolts fas ten ing the pivot support bracket
x 1-1/4" carriage bolt (E) and one 3/8" nylock nut (L).
Do not
tighten at this time.
3/8" x 1-1/4"
CARRIAGE BOLT (E)
3/8" NYLOCK NUT (L)
ANGLE LOCK
BARS
ANGLE LOCK SPRING
tighten yet.
Page 8
so that lock bars can
tighten
the 3/8" carriage bolt and hex nut
When the angle lock bars are pulled back in slot,
1/4" x 3-1/4"
HEX BOLT (A)
1" SPACERS (U)
1/4" NYLOCK
NUT (J)
PIVOT
PLATE
ANGLE
LOCK
SPRING
SPRING
MOUNT
BRACKET
CHANNEL
3/8" PALNUT (S)
PIVOT
PLATE
SPRING
MOUNT
ROD
3/8" PALNUT (S)
3/8" x 1-1/4"
CARRIAGE BOLT (E)
3/8" NYLOCK
NUT (L)
ALIGN CABLE
MOUNT BRACKET
WITH L.H. HOLE
ANGLE
LOCK
BARS
FRONT
Some adjustment of jam nuts may be required
CHANNEL ASSEMBLY
5/16" JAM
NUT (I)
5/16" JAM
NUT (I)
CABLE MOUNT
BRACKET
REAR
3/4"
Page 9
Tighten.
Make sure the cable mount bracket is aligned
3/8" HEX NUT
(TOP)
PLASTIC
CAP
3/8" HEX NUT
(BOTTOM)
BLADE
1/8" x 1-1/4"
COTTER PIN (P)
BLADE
PIVOT
SHAFT
SPRING
MOUNT
ROD
BLADE
ADJUST
SPRING
1/8" x 1-1/4"
COTTER PIN (P)
PIVOT PLATE
NOTCHED HOLE
HAIRPIN
COTTER (O)
PIVOT SUPPORT
BRACKET
CHANNEL
PIVOT PIN
CHANNEL
ASSEMBLY
1/2" WASHER (Q)
CHANNEL
ASSEMBLY
HOLE
1/4" x 1-1/2"
HEX BOLT (B)
CABLE END
FITTING
1/4" NYLOCK
NUT (J)
5/8" SPACER (T)
CHANNEL
ASSEMBLY
HOLE
REAR
Page 10
the fi rst
jam nut from the
secure it with the fi rst jam nut.
Some adjustment of jam nuts may be required
RUBBER
CAP
CABLE MOUNT BRACKET
JAM NUTS
3/4"
CONTROL CABLE END
LIFT HANDLE ROD
HAIRPIN COTTER (O)
LONG PIN
(LIFT LINK)
WELDED BRACKET
LIFT HANDLE TUBE
5/16" x 1-1/2"
HEX BOLT (C)
PLASTIC
GRIP
LOCK RELEASE
GRIP ASSEMBLY
1/4" WELD
BOLT
CABLE END
FITTING
5/16" NYLOCK
NUT (K)
1/4" NYLOCK
NUT (J)
CABLE
BLADE PIVOT
ROD
LIFT HANDLE
TUBE
BLADE
PIVOT SHAFT
HAIRPIN
COTTER (O)
HAIRPIN COTTER (O)
PLASTIC TIES
Page 11
OPERATION
BLADE SHOE
BLADE PIVOT SHAFT
LIFT HANDLE TUBE
BLADE PIVOT ROD
BLADE
ADJUST
SPRING
ANGLE
LOCK
BARS
LOCK RELEASE GRIP ASSEMBLY
CONTROL CABLE
LIFT HANDLE ROD
HANDLE TUBE
PULL BACK AND
LIFT UP TO
LOWER BLADE
PULL BACK AND
PUSH DOWN TO
RAISE BLADE
HANDLE GRIP
HANDLE TUBE
LOCK RELEASE
GRIP ASSEMBLY
LIFT ROD
Page 12
your snow blade for traction. These accessories are
repeatedly push snow in the same di rec tion.
MAINTENANCE SCHEDULE
complete regular service.
After each use
Every season
Before storage
Check for worn or damaged parts X
Clean Blade X X
Lubricate Blade X
MAINTENANCE
GREASE
LUBRICATE
LUBRICATE
•
Page 13
SERVICE AND ADJUSTMENTS
BLADE SHOE
CABLE MOUNT BRACKET
5/16" HEX
JAM NUT
CONTROL
CABLE
5/16" HEX
JAM NUT
STORAGE
Page 14
TROUBLESHOOTING
Page 15
Page 16
Page 17
Page 18
PARTS
B
B
A
A
3
8
8
10
30
35
35
50
33
34
45
38
23
46
32
42
56
15
14
19
39
40
24
27
20
48
48
37
47
41
41
25
36
25
25
11
36
21
17
13
44
47
43
12
26
4
5
4
7
7
44
44
44
44
47
31
55
36
25
C
C
57
54
2
1
9
18
22
29
28
49
51
9
51
51
51,59
51
16
16
44
16
16
16
16
16
5
52
58
58
52
52
53
38
58
Page 19
Page 20
® Registered Trademark / TM Trademark /SM Service Mark of Sears Brands, LLC
® Marca Registrada /
TM
Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC
Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC
Get it fixed, at your home or ours!
Your Home
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
®
(1-888-784-6427)
Au Canada pour service en français:
1-800-LE-FOYER
MC
(1-800-533-6937)
www.sears.ca
Loading...