Craftsman 315.27122 User Manual

Owner's Manual

iP R 0 F E S S I O N A L I

318in. PROFESSIONAL
CORDLESS DRILL-DRIVER

Variable Speed / Reversible

Model No.

315.271220

Save this manual for
future reference

CAUTION: Read and

follow all Safety Rules and
Operating Instructions before

first use of this product.

Customer Help Line: 1-800-932-3188

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman

972000-709

12-99

• Safety

• Features

• Assembly

• Operation

• Maintenance

• Parts List

®

TABLE OF CONTENTS

• General Safety Rules ................................................................................................................................................. 2-3

• Specific Safety Rules/Symbols .................................................................................................................................. 3-5

• Features ..................................................................................................................................................................... 5-7

• Assembly .................................................................................................................................................................... 8-9

• Operation ................................................................................................................................................................ 10-14

• Maintenance ................................................................................................................................................................ t5

• Accessories ................................................................................................................................................................. 16

• Exploded View And Repair Parts List ......................................................................................................................... 17

• Parts Ordering / Service .............................................................................................................................................. 18

WARNING: Read and understand all instructions.

n

Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal

injury.

SAVE THESE INSTRUCTIONS
Work Area

• Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.

Do not operate power tools in explosive atmo-

spheres, such as in the presence of flammable

liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while

operating a power tool. Distractions can cause you

to lose control.

Electrical Safety

Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords

immediately. Damaged cords may create a fire.

A battery operated tool with integral batteries or a

separate battery pack must be recharged only with
the specified charger for the battery. A charger that

may be suitable for one type of battery may create a

risk of fire when used with another battery. Use battery

only with charger listed.

MODEL BATTERY PACK CHARGER

315.271220 Item No. 9-11031 Item No. 2-11040

Use battery operated tool only with specifically
designated battery pack. Use of any other batteries

may create a risk of fire Use only with battery pack
listed.

Personal Safety

Stay alert, watch what you are doing and use
common sense when operating a power tool. Do

not use tool while tired or under the influence of

drugs, alcohol, or medication. A moment of inatten-
tion while operating power tools may result in serious

personal injury.

• Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep your hair, clothing,

and gloves away from moving pads. Loose clothes,

jewelry, or long hair can be caught in moving parts.

• Avoid accidental starting. Be sure switch is in the

locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or

inserting the battery pack into a tool with the switch on,
invites accidents.

Remove adjusting keys or wrenches before turn-
ing the tool on. A wrench or a key that is left attached

to a rotating part ofthe tool may result in personal

injury.

• Do not overreach. Keep proper footing and bal-
ance at all times. Proper footing and balance enable

better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.

2

Tool Use and Care

• Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and

may lead to loss of control.

• Do not force tool. Use the correct tool for your

application. The correct tool will do the job better and
safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off.

A tool that cannot be controlled with the switch is

dangerous and must be repaired.

• Disconnect battery pack from tool or place the switch

in the locked or off position before making any adjust-
ments, changing accessories, or storing the tool. Such

preventive safety measures reduce risk of starting the tool
accidentally.

• Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands

of untrained users.

• When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause
sparks, burns, or a fire.

• Maintain tools with care. Keep cutting tools sharp

and clean. Properly maintained tools, with sharp

cutting edges are less likely to bind and are easier to

control.

• Check for misalignment or binding of moving parts,

breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by

poorly maintained tools.

• Use only accessories that are recommended by

the manufacturer for your model. Accessories that

may be suitable for one tool, may create a risk of injury

when used on another tool.

Service

Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.

When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a

risk of shock or injury.

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

Additional Rules For Safe Operation

Know your power tool. Read operator's manual

carefully. Learn its applications and limitations, as

well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of

electric shock, fire, or serious injury.

Make sure your extension cord is in good condi-
tion. When using an extension cord, be sure to
use one heavy enough to carry the current your
product will draw. A wire gage size (A.W.G.) of at

least 16 is recommended for an extension cord
100 feet or less in length. A cord exceeding 100

feet is not recommended. If in doubt, use the next

heavier gage. The smaller the gage number, the
heavier the cord. An undersized cord will cause a

drop in line voltage resulting in loss of power and
overheating.

Important Rules for Battery Tools

• Battery tools do not have to be plugged into an

electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when chang-

ing accessories. Following this rule will reduce the

risk of electric shock, fire, or serious personal injury.

Do not place battery tools or their batteries near

fire or heat. They may explode. Following this rule

will reduce the risk of electric shock, fire, or serious

personal injury.

Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of

electric shock, fire, or serious personal injury.

Your battery tool should be charged in a location
where the temperature is more than 50°F but less

than IO0°F. Following this rule will reduce the risk of

electric shock, fire, or serious personal injury.

Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with

soap and water, then neutralize with lemon juice

or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek

immediate medical attention. Following this rule will
reduce the risk of serious personal injury.

Important Safety Instructions For Charger

• Save these instructions. This manual contains

important safety and operating instructions for
battery charger part number 9-11040. Following this

rule will reduce the risk of electric shock, fire, or

serious personal injury.

• Before using battery charger, read all instructions

and cautionary markings in this manual, on

battery charger, and product using battery
charger. Following this rule will reduce the risk of

electric shock, fire, or serious personal injury.

• To reduce risk of injury, charge only nickel-

cadmium and nickel metal hydride type recharge-
able batteries, Othe r types of batteries may burst

causing personal injury and damage. Following this
rule will reduce the risk of electric shock, fire, or

serious personal injury.

• Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or

serious personal injury.

• Use of an attachment not recommended or sold

by the battery charger manufacturer may result in

a risk of fire, electric shock, or injury to persons.

Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.

• To reduce risk of damage to charger body and

cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will

reduce the risk of electric shock, fire, or serious
personal injury.

• Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce

the risk of serious personal injury.

• An extension cord should not be used unless
absolutely necessary. Use of improper extension

cord could result in a risk of fire and electric shock. If

extension cord must be used, make sure:
a. That pins on plug of extension cord are the

same number, size and shape as those of

plug on charger.

b. That extension cord is properly wired and in

good electrical condition; and

c. That wire size is large enough for AC ampere

rating of charger as specified below:
Cord Length (Feet) 25' 50' 100'
Cord Size (AWG) 16 16 16

Note: AWG = American Wire Gage

• De not operate charger with a damaged cord or

plug. If damaged, have replaced immediately by a

qualified serviceman. Following this rule will reduce

the risk of electric shock, fire, or serious personal

injury.

• DO not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or

serious personal injury.

• Do not disassemble charger; take it to a qualified

serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal

injury.

• To reduce the risk of electric shock, unplug

charger from outlet before attempting any mainte-
nance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the

risk of electric shock, fire, or serious personal injury.

• Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious

personal injury.

Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of

electric shock, fire, or serious personal injury.

DANGER: RISK OF ELECTRIC SHOCK. DO NOT

u

TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY TERMI-
NAL.

• Save these instructions. Refer to them frequently

and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will

reduce the risk of electric shock, fire, or serious

personal injury.

SYMBOLS

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

rain Minutes Time

"_ Alternating Current Type or a characteristic of current

--= Direct Current Type or a characteristic of current

no No Load Speed Rotational speed, at no load

.../min Revolutions or Reciprocation Per Minute Revolutions, strokes,

surface speed, orbits etc. per minute

A Safety Alert Symbol Indicates danger, warning or caution.

It means attentionH! Your safety is
involved.

DEFINITIONS

A)

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

B)

WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

c)

CAUTION: Failure to obey a safety warning may result in property damage or personal injury
to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric

shock and personal injury.

D)

NOTE: Advises you of information or instructions vital to the operation or maintenance of the
equipment.

I

5

KNOW YOUR DRILL-DRIVER

See Figure 1.

Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety

requirements.

_i WARNING: Carefully read through this entire owner's

manual before using your new drill-driver. Pay close
attention to the Rules For Safe Operation, Warnings
and Cautions. If you use your drill-driver properly and
only for what it is intended, you will enjoy years of safe,

reliable service.

WRIST STRAP

A wrist strap is provided to reduce the chances of dropping
your drill-driver. Place one hand through the wrist strap

when carrying tool.
BIT STORAGE

When not in use, bits provided with your drill-driver can be
placed in the storage area located on the top of the motor
housing.

LEVEL

To keep drill bit level during drilling operations, a level is
located on the top and end of the motor housing.

_i WARNING: Do not allow familiarity with your drill-

driver to make you careless. Remember that a care-

less fraction of a second is sufficient to inflict severe
injury.

KEYLESS CHUCK
Your drill-driver has a keyless chuck that allows you to hand

tighten or release drill bit in the chuck jaws.

SWITCH

To turn your drill-driver ON, depress the switch trigger.

Release switch trigger to turn your drill-driver OFF.

SWITCH LOCK

The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting

when not in use.

VARIABLE SPEED

This tool has a variable speed switch that delivers higher

speed with increased trigger pressure. Speed iscontrolled
by the amount of switch trigger depression.

TWO SPEED GEAR TRAIN

Your drill-driver has a two speed gear train designed for

drilling or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO speed.

FORWARD/REVERSE SELECTOR
(DIRECTION OF ROTATION SELECTOR)

Your drill-driver has a forward/reverse selector located
above the switch trigger.

_i, WARNING: If any pads are missing, do not operate

your drill-driver until the missing parts are replaced.

Failure to do so could result in possible serious

personal injury.

PRODUCT SPECIFICATIONS:

DRILL-DRIVER 315.271220

Chuck
Motor
Gear Train
Switch

No Load Speed

Clutch

Maximum Torque

CHARGER

Input

Charging Voltage

Charge Rate

BATTERY PACK

120 V, 60 Hz, AC only

3/8 in. Keyless

DC Motor 12 Volt

Two Speed

Variable Speed

0°350 RPM (Low)

0-1100 RPM (High)

24 Positions

350 in./Ibs.

ITEM NO. 9-11040

9.6 - 24 Volt

1 Hour

ITEM NO. 9-11031

6

BA'FIB_

PACK

I.B/B.

BrrSIOFIA6E

Q'_RGE_

GRBE_UG-I]'"ON"INDCA'I_SFULLY

_/_DSLOWQ-I/_NG

TOf_t_Nr,_NI_._ PACK

Fig. I

CHARGER

See Figure 2.

Your charger has a "key hole" hanging feature for convenient, space saving storage. Screws should be installed so that
center distances are 4-1/8 inches apart.

4-1/8in.

BA_ PACK_I"I3V_

IN_ Fig. 2

7

INSTALLING BITS

See Figure 3.

• Lock the switch trigger by placing the direction of
rotation selector incenter position. See Figure 10.

• Open or close chuck jaws to a point where the open-
ing is slightly larger than the bit size you intend to use.

Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.

• Insert drill bit into chuck the full length of the jaws as

shown in Figure 3.

_ WARNING: Do not insert drill bit into chuck jaws

and tighten as shown in Figure 4. This could cause
drill bit to be thrown from drill resulting in possible
serious personal injury or damage to the chuck.

DRLLBIT

LOCK

Q-IXX9..I_-VE

Fig. 3

Tighten the chuck jaws on drill bit. To tighten, grasp

and hold the drill with one hand, while rotating the

chuck sleeve with your other hand.

Note: Rotate the chuck sleeve in the direction of the
arrow marked LOCK to tighten chuck jaws.

• Do not use a wrench to tighten or loosen the chuck
jaws,

WRONG Fig. 4

REMOVING BITS

See Figure 3.

• Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.

• Loosen the chuck jaws from drill bit.

• To loosen, grasp end hold the drill with one hand,

while rotating chuck sleeve with your other hand.
Note: Rotate chuck sleeve in the direction of the arrow

marked UNLOCK to loosen the chuck jaws.

• Do not use a wrench to tighten or loosen the chuck
jaws.

• Remove drill bit from chuck jaws.

8

TO ATTACH BATTERY PACK TO DRILL

See Figure 5.

Note: Battery pack is shipped in a low charge condition.

Therefore, it must be charged prior to use. Refer to page 10,

"CHARGING BATTERY PACK" for charging instructions.

• Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.

• Align raised ribs on battery pack with grooves on
bottom of drill, then attach battery pack to drill as
shown in Figure 5.

• Make sure latch on battery pack snaps in place and
battery pack is secured to drill before beginning
operation.

TO REMOVE BATTERY PACK FROM DRILL

See Figure 6.

• Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.

• Depress latch located on front of battery pack (1) to
release battery pack.

• Pull forward on battery pack (2) to remove from drill.

PUlJ_

TORBVlOVE

(_CX]VES

BA_ PACK

_1= CAUTION: When attaching battery pack to your

drill, be sure raised ribs and grooves align properly
and latch snaps in place properly. Improper assembly

can cause damage to drill and battery pack.

Fig. 6

Fig. 5

_1 WARNING: Always wear safety goggles or safety

glasses with side shields when operating tools.

Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.

CHARGING BATTERY PACK

The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,

you should charge ituntil light on front of charger changes
from red to green.

Note: Batteries will not reach full charge the first time they

are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.

TO CHARGE

• Charge battery pack only with the charger provided.

• Make sure power supply is normal house voltage,

120 volts, 60 Hz, AC only.

• Connect charger to power supply.

• Attach battery pack to charger by aligning raised ribs
on battery pack with grooves in charger, then slide

battery back onto charger. See Figure 7.

GR00VI_

Fig. 7

• Red light should turn on. Red light indicates fast
charging mode.

If red light is flashing, this indicates battery pack is

deeply discharged or hot.

If battery pack is hot, red light should become steady
after battery pack has cooled down.

tf battery pack is deeply discharged, red light should
become steady after voltage has increased, normally

within 60 minutes.

If after one hour red light is still flashing, this indicates a

defective battery pack and should be replaced.

Green light on indicates battery pack is fully charged

and slow charging to maintain battery pack.
Yellow tight on and red light flashing indicates defective

battery pack. Return battery pack to your nearest Sears
Repair Center for checking or replacing.

• When your battery pack becomes fully charged, the red light
willtum OFF and the green lightwill turn ON.

• After normal usage, 1 hour of charging time is required to be
fully charged. A minimum charge time of 1-1/2 hours is
required to recharge a completely discharged tool.

• The battery pack will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.

• Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.

• When the batteries become fully charged, unplug your
charger from power supply and remove the battery

pack.

LED FUNCTION OF CHARGER

LED WILL BE LIGHTED TO INDICATE STATUS OF

CHARGER AND BATTERY PACK:

• Red LED Lighted = Fast Charging Mode.

• Green LED Lighted = Fully Charged And Slow

Charging To Maintain Battery Pack.

• Red LED Flashing = Hot Or Deeply Discharged
Battery Pack. Also Defective Battery Pack After 1

Hour.

• Yellow LED Lighted and Red LED Flashing =

Defective Battery Pack.

IMPORTANT INFORMATION FOR RECHARGING
HOT BATTERIES

Under extreme continuous use, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 1 hour before attempt-
ing to recharge. When the battery pack becomes dis-
charged and is hot, this will cause the red light on your

battery charger to flash. When battery pack cools down,
red light will glow continuously indicating fast charging
mode, 1 hour charge time. Once the battery pack cools
down, it will recharge battery pack in fast charging mode

as normal.
Note: This situation only occurs when extreme continuous

use of your drill causes the batteries to become hot. It
does not occur under normal circumstances. Refer to

"CHARGING BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack
under normal circumstances, return both the battery pack

and charger to your nearest Sears repair center for

electrical check.

10

SWITCH

See Figure 8.

To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.

SB..BC_R

c_ln_l:_6nlON

(LOCI<)

SWITCH LOCK

See Figure 10.

The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental

starting when not in use. To lock switch trigger, place the
direction of rotation selector in center position.

REVm

(LOCI<)

9NITCH

1RGGi_

Fig. 8

VARIABLE SPEED
This tool has a variable speed switch that delivers higher

speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.

Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal

part of the switch function.
TWO SPEED GEAR TRAIN

See Figure 9.

Your drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of your drill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque. Use

LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.

"IWOSPB_ LO

GF._'m_N(re.O)

Fig. 10

_h WARNING: Battery tools are always in operating

condition. Therefore, switch should always be locked
when not in use or carrying at your side.

REVERSIBLE

See Figure 10.

This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the

switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be

positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of

the switch. When the selector is in center position, the
switch trigger is locked.

,_ CAUTION: To prevent gear damage, always allow

chuck to come to a complete stop before changing
the direction of rotation or the two speed gear train

(hi-lo).

To stop, release switch trigger and allow the chuck to

come to a complete stop.

Fig. 9

11

KEYLESS CHUCK

See Figure 11.

A keyless chuck has been provided with your drill to allow
for easy installation and removal of bits. As the name
implies, you can hand tighten or release drill bits in the
chuck jaws. Arrows on the chuck indicate which direction
to rotate the chuck sleeve in order to LOCK (tighten) or

UNLOCK (release) the chuck jaws. Loosen the chuck

sleeve by rotating it counterclockwise with one hand.

Insert drill bit into the chuck the full length of the jaws,
tighten securely by rotating the chuck sleeve in clockwise

direction.

DRU.BIT

Fig. 11

,_ WARNING: Do not hold chuck sleeve with one

hand and use power of the drill to tighten chuck jaws

on drill bit. Chuck sleeve could slip in your hand or
your hand could slip and come in contact with

rotating drill bit. This could cause an accident
resulting in serious personal injury.

Fig. 12

Note: Remember the two-speed feature (HI-I.O) when
setting torque. The amount of torque will vary depending
on which speed setting you have your drill-driver. Switch-

ing to LO speed will increase torque. Switching to HI

speed will decrease torque.

BIT STORAGE

See Figure 13.

When not in use, bits provided with your drill can be

placed in the storage area located on the top of your drill

as shown in Figure 13.

BTSTORAGEN]EA

ADJUSTABLE TORQUE CLUTCH

Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and
the size of screw you are using.

TO ADJUST TORQUE

• identify the twenty four torque indicator settings
located on the front of your drill. See Figure 12.

• Rotate adjusting ring to the desired setting.

1 - 4 For driving small screws.

• 5 - 8 For driving screws into soft
material.

• 9 - 12 For driving screws into soft and
hard materials.

• 13 - 16 For driving screws in hard wood.

• 17 - 20 For driving large screws.

• 21 -_11 For heavy drilling.

Fig 13

12

APPLICATIONS
(Use drill-driver only for the purpose listed below)

• Drilling in wood.

• Drilling in ceramics, plastics, fiberglass, and lami-
nates.

• Drilling in both hard and soft metals.

• Using driving accessories, such as driving screws
with screwdriver bits.

• Mixing paints.

LEVEL DRILLING

See Figure 14.

A convenient feature provided on your drill is a level. It is

recessed in the motor housing on top and end of your
drill. It can be used to keepdrill bits level during most
drilling operations.

TOP_IEW

DRILLING

See Figure 15.

,[L=VB.

Fig. 15

When drilling hard smooth surfaces use a center punch to
mark desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.

The material to be drilled should be secured in a vise or
with clamps to keep it from turning as the drill bit rotates.

Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.

Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do net force or apply side
pressure to elongate a hole.

,_ WARNING: Be prepared for binding or bit

breakthrough. When these situations occur, drill has

a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when

breaking through material. If not prepared, this loss
of control can result in possible serious injury.

When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.

If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.

13

CHUCK REMOVAL

See Figures 16, 17, and 18.

The chuck must be removed in order to use some
accessories. To remove:

• Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.

• Insert a 5/16 inch or larger allen wrench (hex key
wrench) into the chuck of your drill and tighten the chuck

jaws securely.

• Tap the allen wrench sharply with a mallet in a
clockwise direction. See Figure 16.This will loosen
the screw in the chuck for easy removal.

Insert allen wrench in chuck and tighten chuck jaws
securely. Tap sharply with a mallet in a counterclock-
wise direction, This will loosen chuck on the spindle. It
can now be unscrewed by hand. See Figure 18.

Fig. 18

Fig. 16

• Open chuck jaws and remove allen wrench. Remove
the chuck screw by turning it in a clockwise direction.

See Figure 17.

Note: The screw has left hand threads.

Fig. 17

TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on spindle and develop a

wobble. Also, the chuck screw may become loose caus-

ing the chuck jaws to bind and prevent them from closing.

To tighten, follow these steps:

• Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.

• Insert allen wrench into chuck and tighten chuck jaws

securely. Tap allen wrench sharply with a mallet in a
clockwise direction. This will tighten chuck on the

spindle.

• Open the chuck jaws and remove allen wrench.

• Tighten the chuck screw.
Note: The chuck screw has left hand threads.

14

WARNING: When servicing use only identical
Craftsman replacement parts. Use of any other

parts may create a hazard or cause product damage.

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, carbon dust, etc.

_ WARNING: Do not at any time let brake fluids,

gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.

BATTERIES

The battery pack for your drill-driver is equipped with

nickel-cadmium rechargeable batteries. Length of service
from each charging will depend on the type of work you
are doing.

The batteries in this tool have been designed to provide

maximum trouble free life. However, like all batteries, they

will eventually wear out. Do not disassemble battery pack

and attempt to replace the batteries. Handling of these

batteries, especially when wearing rings and jewelry,

could result in a serious burn.

To obtain the longest possible battery life, we suggest the

following:

Do not abuse power tools. Abusive practices can
damage tool as well as workpiece.

Only the parts shown on parts list, page 17, are intended
to be repaired or replaced by the customer. All other parts
should be replaced by a qualified service technician at an
authorized service facility.

_L WARNING: Do not attempt to modify this tool or

create accessories not recommended for use with
this tool. Any such alteration or modification is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

• Store and charge your batteries in a cool area.
Temperatures above normal room temperature will
shorten battery life.

• Never store batteries in a discharged condition.

Recharge them immediately after they are

discharged.

• All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If

you store your tool for long periods of time without

using it, recharge the batteries every month or two.

This practice will prolong battery life.

To preserve natural resources, please

recycle or dispose of properly.

This product contains nickel-cadmium

batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium

batteries in ordinary trash.

Consult your local waste authority for information
regarding available recycling and/or disposal options.

OVERLOAD

Your drill has a built-in overload protector to protect the motor during overloading or prolonged use. The overload
protector automatically activates to break the circuit. When this occurs, allow your drill to cool a few seconds before

resuming operation.

BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING

_k WARNING: Upon removal, cover the battery pack's

terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or

remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.

Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep

away from children. Failure to comply with these
warnings could result in fire and/or serious injury.

15

The following recommended accessories are currently available at Sears Retail Stores.

• 6-Pc. Extra Length Magnite Power Bit Set

• 30-Pc. Power Screwdriver/Nutdriver Set and Case

_i, WARNING: The use of attachments or accessories not listed might be hazardous.

_, WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can

result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision

Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores.

WARRANTY

FULL ONE YEAR WARRANTY ON CRRFTSMRNPROFESSIONAL CORDLESS DRILL-DRIVER

If this CRAFTSMAN Professional Cordless Drill-Driver fails due to a defect in material or workmanship within one year

from the date of purchase, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE IN

THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

• 17-Pc. Power Screwdriver/Nutdriver Set and Case

• High Speed Bits (For Wood or Metal)......3/4 in. Max.

SAVETHESEINSTRUCTIONS

16

CRAFTSMAN 318 in. PROFESSIONAL CORDLESS DRILL-DRIVER

MODEL NO. 315.271220

The model number will be found on a plate attached to the motor housing. Always mention the model number

in all correspondence regarding your CRAFTSMAN 3/8 in. PROFESSIONAL CORDLESS DRILL-DRIVER

I

or when ordering repair parts.

SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS

2

I

5

Key

No.

2

4

4

PARTS LIST

PaN
Number

1

3

5
6

616478-003
981502-001
981501-001

981497-001
972000-709

Description Quan.

Screw (Special) ................................................................................ 1

Chuck (Item No, _9-20955)................................................................ 1

Logo Plate ........................................................................................ 1

Battery Pack (Item No. 9-11031) ..................................................... 1

Battery Charger (Item No. -9-11040) ................................................ 1

Carrying Case - Not Shown ............................................................. 1

Owner's Manual

* Can Be Purchased At Your Nearest Sears Retail Store

17

In U.S.A. or Canada

for in-home major brand repair service:

Call 24 hours a day, 7 days a week

1-8004-MY-HOME sM(1-800-469-4663)

Para pedir servicio de reparacibn a domicilio - 1-800-676-5811
Au Canada pour tout le service ou les pi_ces - 1-800-469 4663

For the repair or replacement parts you need:

Call 6 a.m. - 11 p.m. CST, 7 days a week

Parts Direct s_

1-800-366-PART (1-800-366-7278)

Para ordenar piezas con entrega a domicilio - 1-800-659-7084

For the location of a Sears Service Center in your area:

Call 24 hours a day, 7 days a week

1-800-488-1222

To purchase or inquire about a Sears Maintenance Agreement:

Call 7 a.m. - 5 p.m. CST, Monday - Saturday

1-800-827-6655

p.-

HomeCentralS°