Craftsman 137.24883 Operator's Manual
Operator's Manual
3.0 HP (Max. Developed)
10" Inch Blade
5000 R.P.M.
TABLE SAW
Model No.
137.248830
CAUTION:
Before using this Table Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions
• Safety Instructions
• Installation
• Operation
• Maintenance
• Parts List
Customer Help Line
1-800-843-1682
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit our Craftsman website: www.sears.com/craftsman
Part No. 13724883001
SECTION PAGE
Warranty ........................................ 2
Product Specifications ....................... 2
Power Tool Safety ............................ 3
Table Saw Safety .............................. 4
Electrical Requirements and Safety ...... 5
Accessories and Attachments .............. 6
Tools Needed For Assembly ................ 6
Carton Contents .............................. 6
SECTION PAGE
Know Your Table Saw....................... 8
Assembly and Adjustments ................. 9
Operation ....................................... 16
Maintenance ................................... 20
Troubleshooting Guide ....................... 21
Parts List ........................................ 22
Push Stick Pattern ........................... 30
FULL ONE YEAR WARRANTY
If this product fails due to a defect in material or workmanship within one year from the date of purchase, Sears will
at its option repair or replace it free of charge.
Contact a Sears Service Centre for replacement.
If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of
purchase.
This warranty is in addition to any statutory warranty.
Sears, Roebuck & Co., Dept. 817 WA, Hoffman Estates, IL 60179
[A WARNING I
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals work in a well-ventilated area and work with approved safety equipmentsuch as dust
masks that are spec a y des gned to f ter out m croscop c part c es.
MOTOR
HP (Maximum developed) ..... 3.0
Type .................................. Universal
Amps ................................. 15
Voltage .............................. 120
Hz ...................................... 60
RPM (no load) .................... 5000
Overload Protection ............. YES
[A WARNING I
SAW
Table Size........................ 26-7/64" x 19-1/2"
Table Extensions ............... 3 - Left,Right,Rear
Extension Rip Capacity ....... 24" Right and Left
Blade Size ........................ 10" Diameter
Arbor Size ........................ 5/8" Diameter
Rip Fence ........................ Self Aligning
Miter Gauge ...................... T-Slotted
Maximum Cut Depth @ 90% 3"
Maximum Cut Depth @ 45°.. 2-1/2"
Maximum Dado Cut Width... 1/2"
Net Weight ...................... 65 LBS
To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.
This table saw is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere
time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it isworn, cut or
damaged in any way.
Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these
rules could result in serious injury to you or damage to the table saw.
I_ WARNING]
Before using your table saw, it is critical that you read and understand these safety rules.
Failure to follow these rules could result in serious injury or damage to the table saw.
Good safety practices are a combination of common
sense, staying alert and understanding how to use your
power tool. To avoid mistakes that could cause serious
injury, do not plug in your power tool until you have read
and understood the following safety rules:
1. READ and become familiar with this entire
Operator's Manual. LEARN the tool's applications,
limitations and possible hazards.
2. [A WARNING I
Look for this symbol that identifies important
safety precautions. It means CAUTION!
BECOME ALERT! YOUR SAFETY IS INVOLVED!
3. NEVER OPERATE THIS MACHINE WITHOUT THE
SAFETY GUARD IN PLACE FOR ALL THROUGH
SAWING OPERATIONS.
4. DO NOT USE IN A DANGEROUS ENVIRONMENT
such as damp or wet locations or exposure to rain.
Keep work area well lighted.
5. DO NOT use power tools in the presence of
flammable liquids or gases.
6. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
7. KEEP CHILDREN AWAY. All visitors should be kept
at a safe distance from the work area.
8. DO NOT FORCE THE TOOL. It will do the job better
and safer at the rate for which it was designed.
9. USE THE RIGHT TOOL. Don't force the tool or
attachment to do a job for which it is not designed.
10. WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry that may get caught in moving parts. Non-
slip footwear is recommended. Wear protective hair
covering to contain long hair.
11. WEAR A FACE MASK OR DUST MASK. Sawing,
cutting and sanding operations produce dust.
12. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, cutters, etc.
13. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure the switch is in the OFF
position before plugging into the power supply.
14. USE ONLY RECOMMENDED ACCESSORIES.
Consult the Operator's Manual for recommended
accessories. The use of improper accessories may
cause injury to you or damage to the tool.
15. REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning ON.
16. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER "OFF". Do not leave the tool
before it comes to a complete stop.
17. NEVER STAND ON THE TOOL. Serious injury
could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
18.
19.
20.
21.
22.
23.
24.
DO NOT OVERREACH. Keep proper footing and
balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for most efficient and safest performance.
Follow instructions for lubricating and changing
accessories.
CHECK FOR DAMAGED OR LOOSE PARTS.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
ensure it will operate properly and perform its
intended function. Check for alignment of moving
parts, binding of moving parts, loose mounting and
any other conditions that may affect its safe
operation. A guard or other part that is loose or
damaged should be properly adjusted repaired or
replaced.
MAKE WORKSHOP CHILD PROOF with padlocks,
master switches or by removing starter keys.
DO NOT operate the tool if you are under the
influence of any drugs, alcohol or medication that
could impair your ability to use the tool safely.
ALWAYS WEAR EYE PROTECTION. Any power
tool can throw foreign objects into your eyes that
could cause permanent eye damage. ALWAYS wear
safety goggles (not glasses) that comply with ANSI
safety standard Z87.1. Everyday glasses have only
impact resistant lenses. They ARE NOT safety
glasses.
NOTE: Glasses or goggles not in compliance with
ANSI Z87.1 could cause serious injury when they
break.
DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or
cutter only.
.
ALWAYS USE SAW BLADE GUARD, splitter and 12.
anti-kickback pawls for every operation for which they
can be used, including through sawing. Through
sawing operations are those in which the blade cuts 13.
completely through the workpiece when ripping or
crosscutting.
2. ALWAYS HOLD WORK FIRMLY against the miter
gauge or rip fence.
.
USE A PUSH STICK. Always use a push stick
especially when ripping narrow stock. Refer to ripping
instructions inthis Operator's Manual where the push
stick is covered in detail. A pattern for making your
own push stick is included on page 30.
.
14.
NEVER PERFORM ANY OPERATION FREE HAND, 15.
which means using only your hands to support or
guide the workpiece. Always use either the fence
or the miter gauge to position and guide the work.
IA WARNINGI
16
WARNING: FREEHAND CUTTING IS THE MAJOR
CAUSE OF KICK-BACK & FINGER/HAND
AMPUTATIONS,
5. NEVER STAND or have any part of your body in line
with the path of the saw blade. Keep your hands out
of the saw blade path.
6. NEVER REACH behind or over the cutting tool for
any reason.
7. REMOVE the rip fence when crosscutting.
8. DO NOT USE a molding head with this saw.
9. FEED WORK INTO THE BLADE against the
direction of rotation only.
10. NEVER use the rip fence as a cut-off gauge when
crosscutting.
11. NEVER ATTEMPT TO FREE A STALLED SAW
BLADE without first turning the saw OFF. Turn power
switch OFF immediately to prevent motor damage.
17.
18.
19.
20.
PROVIDE ADEQUATE SUPPORT to the rear and
the sides of the saw table for long or wide workpieces.
AVOID KICKBACKS (work thrown back towards you)
by keeping the blade sharp, the rip fence parallel to
the saw blade and by keeping the splitter, anti-
kickback pawls and guards in place, aligned and
functioning. Do not release work before it has passed
all the way past the saw blade. Do not rip work that is
twisted, warped or does not have a straight edge to
guide it along the fence.
AVOID AWKWARD OPERATIONS and hand
positions where a sudden slip could cause your hand
to move into the saw blade.
NEVER USE SOLVENTS to clean plastic parts.
Solvents could possibly dissolve or otherwise
damage the material. Only a soft damp cloth should
be used to clean plastic parts.
MOUNT your table saw on a bench or stand before
performing any cutting operations. Refer to
ASSEMBLY AND ADJUSTMENTS on page 9.
NEVER CUT METALS or materials which may make
hazardous dust.
ALWAYS USE IN WELL-VENTILATED AREA.
Remove sawdust frequently. Clean out sawdust from
the interior of the saw to prevent a potential fire
hazard.
NEVER LEAVE THE SAW RUNNING
UNATTENDED. Do not leave the saw until it comes
to a complete stop.
Failure to provide sawdust fall-through and removal
hole (if mounting the saw onto a solid surface) will
allow sawdust to build up in the motor area resulting
in a fire hazard and potential motor damage (Please
refer to page 10 for details).
POWER SUPPLY REQUIREMENTS
IA WARNING]
To avoidelectricalhazards,firehazardsordamage tothe
tablesaw,use propercircuitprotection.Always use a
separate electrical circuit for your tools. This power tool is
wired at the factory for 120V operation. Connect it to a
120V, 15Amp circuit and use a 15 Amp time delay fuse
or circuit breaker. To avoid shock or fire, replace the cord
immediately if it is worn, cut or damaged inany way.
EXTENSION CORD REQUIREMENTS
In WARNING]
Any extension cord must be GROUNDED for safe
operation.
MINIMUM GAUGE FOR EXTENSION CORDS
(AWG type / 120 Volt only)
Ampere Rating
Not
More Than More Than
0 6
6 10
10 12
Total length in feet
25' 50' 100' 150'
18 16 16 14
18 16 14 12
16 16 14 12
GUIDELINES FOR EXTENSION CORDS
Any extension cord used for power tools MUST be
grounded (3-wire with two flat prongs and one round
ground prong).
Make sure the extension cord is in good condition. When
using an extension cord, make sure you use one heavy
enough to carry the current the tool will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The table above shows
the correct size to use according to extension cord length
and nameplate ampere rating. If in doubt, use the next
heavier gauge cord. The smaller the gauge number the
heavier the cord.
NOTE: The 12 to 16 Amp rating is correct for this tool. It
is highlighted inthe table above.
Be sure your extension cord is properly wired and in good
condition. Always replace a damaged extension cord or
have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Before connecting the saw to the extension cord, make
sure the saw switch is turned OFF.
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR
BREAKDOWN, grounding provides a path of least
resistance for electric current and reduces the risk of
electric shock. This saw is equipped with an electric cord
that has an equipment grounding conductor and a
grounding plug. The plug MUST be plugged into a
matching receptacle that is properly installed and
grounded in accordance with ALL local codes and
ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit
the receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor (wire) with the green insulation (with or without
yellow stripes) is the equipment grounding conductor. If
repair or replacement of the electric cord or plug is
necessary, DO NOT connect the equipment grounding
conductor to a live terminal.
CHECK with a qualified electrician or service personnel if
you do not completely understand the grounding
instructions, or if you are not sure the saw is properly
grounded.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole grounding receptacles that
accept the saw's plug. Repair or replace damaged or
worn cords immediately.
3-Prong Plug
Grou_ng Lug _._--_._
_'/ _-- Make Sure This
__ It isC_nec_edtoa
Known G rc_nd
%J-X iF"
RECOMMENDED ACCESSORIES
[,A WARNINGJ
Visit your Sears Hardware Department or see the Craftsman
Power and Hand Tools Catalog to purchase recommended
accessories for this power tool.
WARNINGJ
To avoid the risk of personal injury:
• Do not use adjustable (wobble) type dadoes or carbide
tipped dado blades; maximum dado width is 1/2".
• Do not use a dado with a diameter larger than 6".
• Do not use molding head set with this saw.
• Do not modify this power tool or use accessories not
recommended by Sears.
TOOLS NEEDED
Medium screwdrive_
#2 Philtips screwdriver
Straight edge
Adjustable wrench
Combination square
UNPACKING AND CHECKING CONTENTS
Separate all parts from packing materials. Check each part
with the illustration on the next page and the "Table of Loose
Parts" to make certain all items are accounted for, before
discarding any packing material.
[Ik WARNINGI
If any part is missing or damaged, do not attempt to
assemble the table saw, plug in the power cord, or turn the
switch ON until the missing or damaged part is obtained and
is installed correctly.
TABLE OF LOOSE PARTS
ITEM DESCRIPTION QUANTITY
A. Table saw assembly 1
B. Table extension 2
C. Rear table extension 1
D. Rear table extension tube 2
E. Location seat 5
F. Blade guard and splitter 1
G. Guard Mounting bolt, flat washer,
toothed washer, oval washer,
spring wasjer 1 each
H. Rip fence 1
I. Hand wheels 2
J. Dome nuts 2
K. Dado table insert 1
L. Miter gauge 1
M. Hex keys 1
N. Blade wrenches 2
O. Blade 1
X. Dust chute 1
Y. Dust bag 1
STAND
P. Top short leg bracket 2
Q. Top long leg bracket 2
R. Bottom short bracket 2
S. Bottom long bracket 2
T. Legs 4
U. Roller wheel assemblies &
mounting hardware 1
V. Stand mounting hardware 1
W. Fence storage hardware &
Parallel washers 1
NOTE: To make assembly easier, keep contents of box together.
Apply a coat of automobile wax to the table. Wipe all parts
thoroughly with a clean dry cloth. This will reduce friction when
pushing the workiece.
UNPACKING YOUR TABLE SAW
K
L
7
M
A
D
B
G
J
_F
7
RP Q S T V W
Extension wing
locking lever
Blade guard
Rip fence
Table insert Side table
extension wing
Thermal overload
reset switch
ON/OFF switch
& safety key
Bevel angle
pointer & scale
Blade elevation
handwheel
Bevel tilting
handwheel
Blade bevel
lock knob
Table
Miter gauge
Rear outfeed table
extension
Table saw bBase
mounting holes
Roller wheel
locking lever
Stand
Leveling
foot
Stationary wheel
assembly
Dust collection
bag
SAW MOUNTED TO WORK SURFACE (FIG. C)
1. If the leg set will not be used, the saw must be
properly secured to a sturdy workbench using the four
mounting holes at the base of the saw.
2. The surface of the table where the saw is to be
mounted must have a hole large enough to facilitate
sawdust fall-through and removal.
3. Square the saw on the mounting surface and mark
the location of the four 3/8" mounting holes (1).
4. Drill four 3/8" holes into the mounting surface.
5. Mark an 11" square (2) centered between the four
mounting holes (1).
6. Cut out and remove the square.
7. This opening will allow sawdust to fall through the
saw base.
8. Place the saw on the work surface, and align the
mounting holes of the saw with those drilled through
the surface.
9. Fasten the saw to the work surface.
14WARNINGI
Do notoperatethismachine on thefloor.Thisisvery
dangerousand may causeseriousinjury.
Fig,C
BLADE RAISING HANDWHEEL (FIG. E, F)
1. Attach the handwheel (1) to the elevation screw (2)
at the front of the saw.
Make sure the slots (3) in the hub of the
handwheel engage with the pins (4). (Fig. E)
2. Attach and tighten the dome nut (5) at the end of the
shaft (Fig. F).
Fig. E
3 2 4
t
O
O
14WARNINGI
Failure to provide the sawdust fall-through hole will cause
sawdust to build up in the motor area, which may result in
fire or cause motor damage,
Place the dust bag neck opening around the dust
chute and tie the dust bag with string.
BLADE TILTING HANDWHEEL (FIG. G, F)
1. Attach the other handwheel (6) to the blade tilting
screw on the side of the saw in the same manner as
above.
2. Attach and tighten the handwheel dome nut (5).
Fig. F
Loading...