Craftsman 137212920 Owner’s Manual
SLUDENGCOMPOUND
M_TERSAW
E82443
C@US
37J2 LISED
CAUTION:
Before using this Sliding Miter Saw,
read this manual and follow all its
Safety Rules and Operating
Instructions.
o Safety Instructions
o Installation
o Operation
o Maintenance
o Parts List
o EspaSol
Customer Help Line
1o800o843o1682
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Part No. 137212920002
SECTION
PAGE
Warranty ..............................
Product Specifications ...................
I_l==l_l==l======_lu_==_=.J==om=j 2
Safety instructions ......................
Accessories and Attachments .............
Carton Contents ........................
Know Your Sliding Miter Saw ..............
Glossary of Terms ..... .....................................
Assembly and Adjustments ...................................
Operation ...............................................
Maintenance .................... i... : .....................
Troubleshooting guide .......................................
Parts .....................................................
........... 11
........... 12
• ; ......... 20
........... 28
........... 29
........... 30
EspaSol ................................................................ 39
MOTOR
Power source ......... 120 VAC, 60 HZ, 15 AMPS
Horsepower .......... 3 HP (Max. Developed)
Speed .............. 4300 R.RM.
Brake ......... _..... Electric
Double insulated ...... Yes
CUTTING CAPACITY
0" Mitre - 0' Bevel .....
45" Mitre - 0r Bevel ....
0r Mitre - 45" Bevel ....
45' Mitre - 45" Bevel ...
MITRE DETENT STOPS ...
BEVEL POSITIVE STOPS..
CARRIAGE SYSTEM .....
BLADE SIZE ...... ......
4" x 12-5/8"
4" x 8-3/4"
2-1/2" x 12-5/8"
2-1/2" x 8-3/4"
0, 15, 22.5, 31.6, 45" R & L
0, 33.9 & 45" L
3 Rail, ball bearing slide
12"
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known [to the State of Califcrnia] to cause cancer, birth defects or other
reproductive harm Some examples of these chemicals are:
e Lead from lead-based paints
Crystalline silica from bricks, cement and other masonry products
® Arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals:work in a well ventilated area. and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles
ARBOR SIZE .................. 5/8"
TABLE DIAMETER ............. 20-5/8"
DUST COLLECTION ........... Yes
AUXILIARY FENCE EXTENSION ... Yes
NET WEIGHT ................. 61.6 Lb.
To avoid electrical hazards, fire hazards, or damage to
the tool, use proper circuit protection.
Your sliding mitre saw is wired at the factory for 120V
operation. Connect to a 120',/, 15 AMP time delay fuse or
circuit breaker. To avoid shock or fire, replace power cord
immediately if it is worn, cut or damaged in any way.
GENERAL SAFETY mNSTRUCT_ONS
12.
W_ARYOUR ALWAYS WEAR EYE
PROTECTION. Any miter saw
BEFORE USING THE SUD_NG _TER SAW
can throw foreign objects into
the eyes which could cause
Safety is a combination of common sense, staying alert
and knowing how to use your sliding miter saw.
permanent eye damage.
ALWAYS wear Safety Goggles
(not glasses) that comply with
ANSI safety standard Z87.1. Everyday eyeglasses
To avoid mistakes that could cause serious injury, do not
plug the miter saw in until you have read and understood
the following:
i
,
READ and become familiar with this entire instruction
manual. LEARN the tool's applications, limitations, and
possible hazards.
2.
KEEP GUARDS _NPLACE and in working order.
3.
REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ON.
.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
5.
DON'T USE IN A DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations, or
expose them to rain. Keep work area welt lighted.
6,
KEEP CHILDREN AWAY. All visitors should be kept at
a safe distance from the work area.
,
MAKE WORKSHOP KID PROOF wilh padlocks, master
switches, or by removing starter keys.
8.
DON'T FORCE THE TOOL. It will do the job better
and safer at the rate for which it was designed.
9.
.I
USE THE RIGHTTOOL Don't force tool or the
attachment to do a job for which it was not designed.
10.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss
of power and overheating. The table on page 7 shows
the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.
11.
WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
have only impact-resistant lenses. ]hey ARE NOT
safety glasses. Safety Goggles are available at Sears.
NOTE: Glasses or goggles not in compliance with ANSI
2:87.1could seriously hurt you when they break.
13.
WEAR A FACE MASK OR DUST MASK.
Sawing operation produces dust.
14.
SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand and it
frees both hands to operate tool.
15.
DBCONNECT TOOLS before servicing, and when
changing accessories, such as blades, bits, cutters,
and the like.
16.
REDUCE THE RISK OF UNiNTENTiONAL STARTING.
Make sure the switch is in OFF position before
plugging in.
17.
USE RECOMMENDED ACCESSORIES. Consult the
owner's manual for the recommended accessories.
The use of improper accessories may cause risk of
injury to persons.
18.
NEVER STAND ON TOOL. Serious injury could occur
ifthe tool is tipped or if the cutting tool is unintentionally
contacted.
19.
CHECK FOR DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
20.
NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER OFF. Don't leave the tool until
it comes to a complete stop.
21.
DON'T OVERREACH. Keep proper footing and
balance at all times.
22.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
23.
DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or culter only.
SAVE THESE NSTRUCT ONS
2
3
!i! i !::: :::::i:i::ii::i:!¸¸::!:i i:!¸iii!: ii!i
24. DO NOT operate the tool if you are under the
influence of any drugs, alcohol or medication that
could affect your ability to use the tool properly.
25. WARNnNG: Dust generated from certain materials can
be injurious to your health. Always operate miter saw in
well ventilated areas and provide for proper dust removal.
SPEC HC SAFETY NSTRUCT ONS
FOR SUDRNG VHTER SAWS
1. READ AND UNDERSTAND all safety instructions
and operating procedures throughout the manual.
2. DO NOT operate the miter saw until it is completely
assembled and installed according to the instructions.
3. SHOULD any part of your miter saw be missing,
damaged, or fail in any way, or any electrical
component fail to perbrm properly, shut off tile switch
and remove the plug from the power supply outleL
Replace missing, damaged, or failed parts before
resuming operation.
4. IFYOU ARE NOT thoroughly familiar with the
operation of miter saws, obtain advice from your
supervisor, instructor, or other qualified person.
5. NEVER CARRY the tool by the cord or the cutting
head handle. Damage to the insulation could cause
electric shock. Damage to the wire connections could
cause a fire.
6. SERIOUS _NJURY could occur if the tool tips over or
you accidentally hit the cutting tool. Do not store
anything above or near the tool.
7. AVOID nNJURY from unexpected saw movement.
Place the saw on a firm level surface where the saw
does not rock, and bolt or clamp the saw to its support.
8. BEFORE MOWNG the saw, lock the miter, bevel, and
cutting head positions.
9. CHOOSE the right 12" diameter blade for the
material and the type of cutting you plan to do. Never
use blades larger or smaller in diameter than
recommended.
10. USE ONLY CROSSCUTTING SAW BLADES. Do not . piopefiy _up#6!t ih6w0ikpiece and keep yoUr
use blades with deep gullets as they can deflect to hoiGd0wn hand the required distance from the blade.
the side and contact the guard.
11. USE only blade collars specified for your saw. The
recessed sides must Pacethe blade ......
12. USING THE HEX BLADE WRENCH supplied, make
sure the arbor screw is firmly tightened.
13. NEVER USE the saw without the cover plate securely
in place. It keeps the arbor screw from falling out if it
accidentally loosens, and orevents the spinning blade
from cornJng off the machine.
14.
KEEP HANDS out of the path of the saw blade. If the
workpiece you are cutting would cause your hand to
be within 6-1/2 inches of the saw blade, the W0rkpiece
should be clamped in place before making the cut.
15.
MAKE SURE the blade and collars are clean and
properly arranged. After installing a new blade, make
sure the blade clears the table slot at the 0o and 45°
bevel positions. Lower the blade into the table slot and
check for any contact with the base or turn table
structure. If the blade contacts the table, see the
TROUBLESHOOTING GUnDE for "depth stop
adjustment" or contact the Sears Service Center.
Broken saw parts could injure you or others.
16.
ALWAYS check the blade for cracks or damage
before operation. Replace a cracked or damaged
blade immediately.
17.
USE blades recommended at 4300 RPM or greater.
18.
ALWAYS keep the blade guards in place.
19.
TO KEEP the pivot nut from working its way off as you
use the saw, at least one thread of the pivot bolt must
always stick out past the nut. Always keep the nut at
least that tight.
20.
FAILURE TO'RGHTEN the jam nut could let the depth
stop slip and let the blade strike the saw table.
Broken saw parts could injure you or others.
21.
CLEAR EVERYTHING except the workpiece and
related support devices off the table before turning
the miter saw on.
22. MAKE SURE all clamps and locks are tight and
there is no excessive play in any part.
23. ALWAYS MAKE SURE all handles are tight before
cutting, even if the table is positioned in one of the
positive stops.
24. MAKE SURE there are no nails or foreign objects in
•the part of the workpiece to be cut.
25. MAKE SURE the blade is not contacting the workpiece
before the switch is turned on.
26. ALWAYS hold the work firmly against the fence and
table. DO NOT perform any operation freehand.
27. DO NOTTRYTO CUT SHORT PIECES, You cannot
28. ALWAYST_GHTENTHE CLAMP so that the workpiece
is secured between the clamp and fence or base. No
visible gap should be present between saw and wood.
29. NEVER cut metals or masonry. Because of the
sliding action of the saw, this machine is not designed
for cutting metals. Use this miter saw to cut only wood
and woodlike products. Other materials may shatter,
bind on the blade, start fires or create othe- dangers.
30. NEVER reach around the saw blade.
3"1
• NEVER PULL THE SAW toward you during a cut.
The blade can suddenly climb up on Iop of the
workpiece and force itself toward you.
32.
ALLOW the motor to come up to full speed before
starting cut.
33.
KEEP the motor air slots clean and free of chips.
34.
NEVER apply lubricants to the blade when it is
running.
35.
MAKE SURE the blade has come to a complete stop
before removing or securing the workpiece, changing
the workpiece angle, or changing the angle of the
blade.
36.
NEVER use the miter saw in an area with flammable
liquids or gases.
37.
NEVER use solvents to clean plastic parts. Solvents
could possibly dissolve or otherwise damage the
material.
38. ALWAYS PERFORM DRY RUNS+ Make sure the saw
is unplugged. Completely set up your saw. Pull the
blade and cutting head through the full range of motion
to check for interference. When using a clamp make
sure that your blade, saw guard or motor does not
interfere with the clamp. Correct any interference
before use.
39. PLAN HOW YOU WILL MAKE THE CUT:
° MAKE SURE the blade is net spinning.
, RAISE the blade.
, SUDE the saw out above the front edge of the
workpiece before starting the saw.
- PUSH the saw blade down on top of the wood and
back toward the rear of the saw to make the cut.
BEFORE EACH USE
40. JNSPEOTYOUR MITER SAW.
41. D+SCONNECTTHE M_TERSAW. To avoid injury from
accidental starting, unplug the saw before changing
the setup, changing the blade, or adjusting anything.
Compare the direction of the rotation arrow on the
guard to the direction arrow on the blade. The blade
teeth should always point downward at the front of the
saw. Tighten the arbor screw. Tighten the cover plate
screw.
42.
CHECK FOR DAMAGED PARTS° Check for:
° PROPER alignment of moving parts
+ DAMAGED electric cords
, BINDING of moving parts
° BROKEN parts
+ STABLE mounting
+ FUNCTION of arm return spring and lower guard:
Push the arm all the way down, then let it rise
up until it stops by itself. Check the lower guard
to see if it closed fully. If it did not, follow the
instructions in the TROUBLESHOOTONG GUDDE.
SMOOTH, solid movement of sliding assembly.
OTHER conditions that may affect the way the
miter saw works. If any part of the miter is
missing, bent, or broken in any way, or any
electrical parts don't work, turn the saw off and
unplug it. REPLACE damaged, missing, or failed
parts before using the saw again.
4+3,
KEEP GUARDS UNPLACE, in working order, and in
proper adjustment. Maintain tools with care.
Keep the miter saw clean for best and safest
performance. Follow instructions for lubricating.
DON'T put lubricants on the blade while it's spinning,
44. REMOVE adjusting keys and wrenches from the tool
before turning it on.
45.
TO AVOID INJURY FROM JAMS, SMPS, OR
THROWN PECES:
° USE ONLY RECOMMENDED ACCESSORIES.
Consult this Owner's Manual for recommended
accessories. Follow the instructions that come
with the accessories. The use of improper
accessories may cause risk of injury to persons.
o MAKE SURE the blade is sharp, undamaged,
properly aligned and free of vibration. With the
saw unplugged, push the cutting head all the way
down. Hand spin the blade and check for
clearance. Tilt the cutting head to a 45 degree
bevel and repeat the check. If the blade hits
anything, see the TROUBLESHOOTING GUIDE
for "depth stop adjustment", or contact your
Sears Service Center.
46. PLAN HOW you will hold the workpiece from start
to finish:
+ AVOID awkward operations and hand positions
where a sudden slip could cause fingers or
hand to move into the blade.
° DON'T OVERREACH. Keep good footing and
balance.
° KEEP your face and body to one side of the
saw blade, out of line with a possible throwback.
+ NEVER CUT FREEHAND:
+ BRACE your workpiece solidly against the fence
and table top so it will not rock or twist during
the cut.
MAKE SURE there is no debris between the
workpiece and its supports.
- MAKE SURE no gaps between the workpiece,
fence and table wilt let the workpiece shift after
it is cut in two.
° CUT only one workpiece at a time.
° KEEP the cut off piece free to move sideways
after it is cut off. Otherwise it could get wedged
against the blade and be thrown violently•
, CLEAR everything except the workpiece and
related support devices off the worktable before
turning the miter saw on.
° SECURE WORK. Use clamps or a vise to help
hold the work when it is practical.
SAVE THESE WNSTRUCT ONS
SAVE THESE NSTRUCT ONS
5
47.USEEXTRACAUTIONwithlarge,verysmallor
awkwardworkpieces:
USEextrasupports(tables,sawhorses,blocks,
etc.)foranyworkpieceslargeenoughtotip
whennothelddowntothetabletop.
o NEVERuseanotherpersonasa substitutefora
tableextension,orasadditionalsupportfora
workpiecethatislongerorwiderthanthebasic
mitersawtable,ortohelpfeed,supportorpull
theworkpiece.
o DONOTUSEthissawtocutpiecestoosmallto
letyoueasilyholdthework.
WHENCUTTINGirregularlyshapedworkpieces,
planyourworksoitwillnotslipandpinchthe
bladeandbetornfromyourhands.A pieceof
molding,forexample,mustlieflatorbeheldby
afixtureorjigthatwillnotletittwist,rockorslip
whilebeingcut.
o PROPERLYSUPPORTroundmaterialsuchas
dowelrods,ortubing.Theyhaveatendencyto
rollwhilebeingcut,causingthebladeto"bite".
Toavoidthis,alwaysusea fixturedesignedto
properlyholdyourworkpiece.
WHEN THE SAW IS RUNNING
48. BEFORE STARTING your cut, watch the miter saw
while it runs. If it makes an unfamiliar noise or
vibrates a lot, stop immediately. Turn the saw OFF.
Unplug the saw. Do not restart until finding and
correcting the problem.
49. KEEP CHILDREN AWAY. Keep all visitors a safe
distance from the miter saw. Make sure bystanders
are clear of the miter saw and workpiece.
50. LET THE BLADE reach full speed before cutting.
This will help avoid thrown workpieces.
51. DON'T FORCE THE TOOL. It will do the job better
and safer at its designed rate. Feed the saw into the
workpiece only fast enough to let the blade cut without
bogging down or binding.
52. BEFORE FREEING JAMMED MATERIAL:
o TURN miter saw OFF by releasing trigger switch.
o WAiT for all moving parts to stop.
o UNPLUG the miter saw.
53. AFTER FINISHING A CUT:
o KEEP holding the cutting head down.
o RELEASE the switch, keeping the cutting head
down, and wait for all moving parts to stop before
moving your hands.
o IF BLADE doesn't stop within 6 seconds, unplug
the saw and follow the instructions in the
TROUBLESHOOTING GUIDE for fixing the blade
brake before using the saw again.
54. BEFORE LEAVING THE SAW:
NEVER LEAVE the tool running unattended.
Turn the power OFR Wait for all moving parts
to stop.
MAKE WORKSHOP child proof. Lock the shop.
Disconnect master switches. Store the tool away
from children and others not qualified to use the
tool.
55. NEVER unplug the saw with the switch in the ON
position.
56. DISCONNECT the saw from the power source and
clean the machine before leaving it. MAKE SURE the
work area is clean before leaving the machine.
ELECTRICAL REQUIREMENTS
POWER SUPPLY AND MOTOR
SPECIFICATIONS
The AC motor used in this saw is a universal, nonreversible
type. See "MOTOR" in the PRODUCT SPECIFiCATiONS
section on page 2.
To avoid electrical hazards, fire hazards, or damage to the
tool, use proper circuit protection. Yoursaw is wired at the
factory for 120V operation. Connect to a 120V, 15 Amp circuit
and use a 15 Amp time delay fuse or circuit breaker. To avoid
shock or fire, if power cord is worn or cut, or damaged in any
way, have it replaced immediately.
DOUBLE INSULATED _]
The miter saw is double insulated to provide a double
thickness of insulation between you and the tool's electrical
system. All exposed metal parts are isolated from the internal
metal motor components with protecting insulation.
Replacement parts - When servicing use only identical
replacement parts.
Polarized plugs - This saw has a plug that looks like the
one shown below:
To reduce the risk of electrical shock, this saw has a
polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. Ifthe plug
does not fit fully in the outlet, reverse the plug. tf it still
does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
To avoid electrocution:
o Use only identical replacement parts when servicing a
tool with double insulation. Servicing should be
performed by a qualified technician.
o Do not use power tools in wet or damp areas or
expose them to rain.
o This tool is intended for indoor use only.
o Double insulation does not take the place of normal
safety precautions when operating this toot.
MOTOR SAFETY PROTECTION
IMPORTANT: To avoid motor damage, this motor
should be blown out or vacuumed frequently to keep
sawdust from interfering with normal motor ventilation.
CONNECT this tool to a 120V, 15 Amp branch circuit
with a 15 Amp time delay fuse or circuit breaker.
Using the wrong size fuse can damage the motor.
,
IF the motor won't start, release the trigger switch
immediately. UNPLUG THE TOOL. Check the saw
blade to make sure it turns freely. If the blade is free,
try to start the motor again. If the motor still does not
start, refer to the TROUBLESHOOTING GUIDE.
,
tF the motor suddenly stalls wMe cutting wood,
release the trigger switch, unplug the tool, and free
the blade from the wood. The saw may now be
restarted and the cut finished.
.
FUSES may "blow" or circuit breakers rnay trip
frequently if:
a. MOTOR is overloaded. Overloading can occur if
you feed too rapidly or make too many start /
stops in a short time.
b. LINE VOLTAGE is rnore than 10% above or
below the nameplate voltage. For heavy loads,
however, the voltage at motor terminals must
equal the voltage specified on the nameplate.
c. IMPROPER or dull saw blades are used.
,
MOST motor troubles may be traced to loose or
incorrect connections, overload, low voltage (such as
small size wire in the supply circuit) or to overly long
supply circuit wire. Always check the connections, the
load and the supply circuit if the motor doesn't work
well. Check wire sizes and length with the Extension
Cord Chart below.
GUIDELINES FOR EXTENSION CORDS
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heaW enough to carry
the current your product will draw. An undersized cord will
cause a drop in line voltage, resulting in loss of power and
cause overheating. The table below shows the correct size to
use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
Be sure your extension cord is properly wired and in
good condition. Always replace a damaged extension cord or
have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive
heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit
must not be less than #12 wire and should be protected
with a 15 Amp time lag fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF position
and the electric current is rated the same as the current
stamped on the motor nameplate. Running at a lower
voltage will damage the motor.
(when using 120 volts only)
Ampere Rating
more than not nlole Ihal]
0 6
6 t0
10 12
12 16
CAUTION: In all cases, make certain the receptacle in
question is properly grounded. If you are not sure have a
certified electrician check the receptacle.
Totallength ofcordinfeet
25' 50' 100' 150'
18 16 16 14
18 16 14 12
16 16 14 12
14 12 Notrecommended
SAVE THESE
77 7 7 ; Y 7 r 7 t
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
7
UNPACKING YOUR COMPOUND SLIDING MBTER SAW
PROHiBiTED ACCESSORIES
To avoid injury:
° Use only accessories recommended for this sliding
miter saw. Follow instructions that accompany
accessories. Use of improper accessories may cause
hazards.
o The use of any cutting tool except 12 inch saw blades
which meet the requirements under recommended
accessories is prohibited. Do not use accessories such
as shaper cutters or dado sets. Ferrous metal cutting
and the use of abrasive wheels is prohibited.
• Do not attempt to modify this tool or create
accessories not recommended for use with this tool. Any
such alteration or modification is misuse and could
result in a hazardous condition leading to possible
serious injury.
Read warnings and conditions on your CARBIDETIPPED
SAW BLADE. Do not operate the saw without the proper
saw blade guard in place. Carbide is a very hard but brittle
material. Care should be taken while mounting, using, and
storing carbide blades to prevent accidental damage. Slight
shocks, such as striking the tip while handling, can seriously
damage the blade. Foreign objects in the workpiece, such as
wire or nails, can also cause tips to crack or break off.
Before using, always visually examine the blade and tips
for bent blade, cracks, breakage, missing or loose tips, or
other damage. Do not use if damage is suspected. Failure to
heed safety instructions and warnings can result in serious
bodily injury.
UNPACKING AND CHECKING CONTENTS
To avoid injury:
• Do not plug the power cord into a power source
receptacle during unpacking and assembly. This cord
must remain unplugged whenever you are working on
the saw.
Get help whenever you have to lift the saw. This saw
is heavy.
If any part is missing or damaged, do not plug the sliding
miter saw in until the missing or damaged part is
replaced, and assembly is complete. To avoid electric
shock, use only identical replacement parts when
servicing double insulated tools.
Carefully unpack the sliding miter saw and all its parts, and
compare against the illustration on page 9.
1. Before removing the saw from the shipping carton,
tighten the carriage lock knob to guard against
sudden movement.
2. DO NOT LIFT the sliding miter saw by the cutting
head handle. Damage to the insulation or wire
connections could cause fire. Remove the saw from
the carton by lifting with the hand-holds at the base of
the saw body, or use the carry handle.
3. Place the saw on a secure, stationary work surface
and look the saw over carefully.
TABLE OF LOOSE PARTS
ITEM DESCRIPTION QUANTITY
A. Sliding miter saw 1
B. Dust collection chute 1
C. Dust collection elbow 1
D, Auxiliary fence 1
E. Dust bag 1
R Blade wrench 1
B C
E
D
0
o
Dust bag
Depth stop
bolt
handle
Lock-off
switch
ON/OFF
triggerswitch
Blade
storage
Lock pin
Power cord storage
}arriage lock handle
Depth adjustment
45 ° Bevel stop
90 ° Bevel stop
Bevel lock handle
Arbor
lock
Brush covers
Slide carry
Miter lock Motor handle
handle
Slide bar cover
Dust collection elbow blade
Bevel positive Miter
stop lock scale
-- Fence
Exhaust port
Dust exhaust
collection chute
Auxiliary fence
Turntable
Hand-holds Mounting
Blade wrench holes
Base
Bevel scale
Upper
bladeguard
cover
plate
Lower
guard
CRAFTSMAN SLiDiNG COMPOUND MUTER
SAW TERMS
ARBOR LOCK - Allows the user to keep the blade from
rotating while tightening or loosening the arbor screw
during blade replacement or removal.
BASE - Supports the table, holds accessories and allows for
workbench mounting.
BEVEL ADJUSTMENT STOPS = Bolts that are adjusted to
stop the saw blade at 0° and 45° bevel.
BEVEL POS_TaVESTOP LOCK - Locks the miter saw at
the 33.9° bevel angle positive stop.
BEVEL LOCK HANDLE - Locks the miter saw at a desired
bevel angle.
BEVEL SCALE - Measures the bevel angle of the saw
blade.
BLADE WRENCH - Fits the arbor screw for removing and
replacing the blade.
CARRaAGE LOCK HANDLE - Prevents the saw's sliding
motion by locking the carriage in place.
COVER PLATE - Holds the lower guard and is attached to
the upper guard. It prevents the arbor screw from backing out.
CUTTING HEAD ASSEMBLY - Consists of pivot arm,
blade, upper and lower blade guards, motor, arbor and pin
locks, and switch on handle. Components work together to
perform cutting operation.
DEPTH ADJUSTMENT- Allows setting of desired cutting
depth.
DEPTH STOP BOLT - Limits the saw blade travel to
approximately 1/4" below the table.
DUST BAG - Provides a means of collecting sawdust.
DUST COLLECTION ELBOW - Provides a means of
attaching a vacuum or dust collection bag.
DUST COLLECTION CHUTE - Fits into the exhaust port for
efficient sawdust exhaust.
EXHAUST PORT - Exhausts debris away from the operator.
FENCE - Helps to keep the workpiece from moving when
sawing.
HAND-HOLD - Provides a means of safely carrying the saw.
LOCK-OFF SW_TCH - Activates the ON / OFF switch
when pushed. This prevents the trigger switch from being
accidentally turned ON.
LOCK PIN - Locks the miter saw in the lowered position for
compact storage. Use this only for carrying and storage
applications.
LOWER BLADE GUARD - Protects the user's hands from
the blade in the raised position. It retracts as the blade is
lowered to avoid binding on the workpiece.
MATERLOCK HANDLE - Rotates the saw to a right or left
cutting position and locks the miter saw table at the desired
miter angle.
MITER SCALE - Measures the miter angle of the saw
blade. Positive stop index points have been provided at 0, 15,
22.5, 31.6, and 45° right and left.
MOUNTING HOLES - Provides a means of mounting the
sliding miter saw to a stable work surface.
ON / OFFTRIGGER SWITCH - Starts the saw when
squeezed. As a safety feature, the lock-oft button must be
pushed to activate the trigger and turn the saw ON. Release
timetrigger to turn the saw OFR
SLIDE BAR COVER - Covers and protects the 3 slide
carriage rails.
SWITCH HANDLE - Contains the trigger switch with a
lock-off button. The blade is lowered by pushing down on the
handle, and returns to the upright position when the handle
is released.
TURNTABLE - Sits in the base, supports the workpiece,
and allows rotation for miter cutting.
UPPER BLADE GUARD - Protects the user from the saw
blade teeth.
WARNING LABELS - Informs the user of dangers and
necessary precautions in the use of this saw. Read carefully
before using.
WOODWORKUNG TERMS
ARBOR - The shaft on which the blade is mounted.
BEVEL CUT - An angle cut made through the face of a
workpiece.
COMPOUND CUT - A simultaneous bevel and miter cut.
CROSSCUT - A cut made across the width of the workpiece.
FREEHAND - Performing a cut without using a fence
(guide), hold-down or other proper device to prevent the
workpiece from twisting during the cutting operation.
GUM - A sticky sap based residue from wood products.
HEEL - Misalignment of the blade.
KERF - The amount of material removed by a blade in a
through cut, or the slot produced by the blade in a partial cut.
M_TER CUT - An angle cut made across the width of a
workpiece.
RESIN - A sticky sap that has hardened.
REVOLUTIONS PER MINUTE (RPM) - The number of turns
completed by a spinning object in one minute.
SAW BLADE PATH - The area of the workpiece or table top
directly in line with the travel of the blade or the part of the
workpiece which will be cut.
SET - The distance between two tips of the saw blade teeth,
bent outward in opposite directions to each other.
WORKP_ECE - The item being cut. The surfaces of a
workpiece are commonly referred to as faces, ends, edges.
lO
Loading...