Craftsman 113.225909, 113.225900 User Manual

Save This Manual For Future Reference

MODEL NO.

113, 225909

BELT AND DISC

SANDER ONLY

MODEL NO.

113.225931

BELT AND DISC

SANDER!WITH

LEGS AND MOTOR

Serial Number

Model and serial number may be found

at the right hand side of the base,

You should record both model and serial number

in a safe place for

CAUTION:

Read SAFETY INSTRUCTIONS

BEL T AND D/SC SANDER

. assembly ® operating

carefully

Sold by SEARS, ROEBUCK AND CO., Chicago, iL. 60684 U.S.A.

Part No. 68073 Printed in USA

o repair parts

FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER

If within one year from the date of purchase th s Craftsman Belt and Disc Sander fails due to a defect in material or workmanship, Sears will repair it, free of charge.

WARRANTY sERVICE IS AVAILABLE BY S MPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SEARS. ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684

general safety instructions power tools

1. KNOW YOUR POWER TOOL mask if cutting operation is dustv, and ear protectors

Read and understand the owner's manual and labels (plugs or muffs) during extended periods of operation.

affixed to the tool. Learn its application and limitations as well as the specific potential hazards peculiar to this tool. 13. SECU RE WORK

2. GROUND ALL TOOLS

Th_s foot Is equIPbe(1 with an approved 3.conductor cord and a 3-prong grounamg type plug tp fit the proper

groundmg type receptacle Th_ _reen conductor n the

cord _s tha grounding wire. Never connect the green w_re _o a hve termmal.

3. KEEP GUARDS IN PLACE

- m working order, and in proper aolustment and align

ment

4. REMOVE ADJUSTING KEYS AND WRENCHES

Form habit of ¢heckmg to see tnat keys ana adlustmg

wrenches are removed from tool before turning _t pn

5. KEEP WORK AREACLEAN

C_uttereo areas and benches mwte acc_dems FtOol

must not be Slippery due tO wax or SaWdUSt

6. AVOID DANGEROUS ENVIRONMENT

Don't LISP Dower tOOlS in damp or wet locations or ex

(_se them to raln, Keep work area well hghted Provlde

d(lequate surrounding work space Follow the nslrucPons that accompany the accessories.

7. KEEP CHILDREN AWAY

All visitors should be keot a safed_stance from work area

8. MAKE WORKSHOP CHILD-PROOF

w_tn {_adlpcks rnastel swltche_ or r)V remownq starter

I<eVS

9. DON'T FORCE TOOL 20.

It wdl do the IOb bt, tter ana safer at the rate to{ which

• was des_qneo

10. USE RIGHT TOOL

_OCt't foFce too ol dttaci_mPnt to (30 a 1o13 r'[ was not

ties gnea for

11. WEAR PROPER APPAREL

Do not weal loose cIothlnh gloves, rleckttes or _ewelrv brags. _.,rlstwatcnesl to get caugn[ in movlng parts

NONSLIP footwear s iecommended Weal protective 21. nalr covering to contain long halt. Roll long Sleeves

above the elbow

12. USE SAFETY GOGGLES (Head Protection) 22. NEVER LEAVE TOOL RUNN NG Wear safety goggles (must comply with ANSI Z87,1) at all UN ATTENDED

times. Everyday eyeglasses only have impact resistant Turn power off _)on't leave too_ unt_l t comps _o a

lenses, mey are NOT safety glasses. Also use face or dust coml)lete stop

Use clamps or a v_se to hold WOrK When Dractlcal It s safer than uslng your 13and. frees both hands to operate tool.

14. DON'T OVERREACH

Keep ProPer foottng and balance at all bmes

15. MAINTAIN TOOLS WITH CARE

Kee_) tools snaro and clean for best and safest perform ance. Follow nstruct_ons for ubrlcat_ng ano changing accessor les.

16. DISCONNECT TOOLS

before servicing, when changing accessories SUCh as

blades. P_ts. cutters etc

17. AVOID ACCIDENTAL STARTING

Make sure swdch s m "OFF" position before pluggmg

18. USE RECOMMENDED ACCESSORIES

Consult tbeowner's manua for recommended accessories.

The use of mproDer accessories may cause hazards.

19. NEVER STAND ON TOOL

Serious ]nlury could OCCUI _f the tool _s tipper or tf the

cuttmg tool _s accidentally contacteP Do not store materials 3bove or near the tool such mat

it s necessar, to stand on the tool to reach them

CHECK DAMAGED PARTS

Before furmer use of the tool a guard or other _)art thai _s Clamaged should be carefully checked to ensure that LI

will operate properly and perform its intended function Check for alignment of mPvmg Darts bJndmg of mowng baits, breakage of _arts, mountmg, and any other con

dd_ons that may affect ts operation. A guaro Ol othe_ oa_I that is damage(] should De properly repaired Ol

replaced

DIRECTION OF FEED

Feed work mto a blade or cutter aga nst the ChrPCtion Of rotation of the blade or cutter only

safety instructions for beJt and disc sander

Safety is a combination of common sense, staying alert and knowing how your belt and disc sander works. Read this

manual to understand this sander.

BEFORE USING THE SANDER:

WARNING: To avoid mistakes that could cause serious, per- manent injury, do not plug the sander in until the following steps are completed.

o Assembly. (See pages 7 - 16.) o Learn the use and function of the ON-OFF switch,

backstop lock screw, belt adjusting screws, belt lock- ing screws, work table and work table tilt lock screw.

(See pages 16 - 18.)

o Review and understanding of all safety instructions and

operating procedures in this manual.

" Review of the maintenance methods for this sander.

(See page 22.)

Read the following DANGER label found on the front of the sander:

WHEN INSTALLING OR MOVING THE

SANDER.

AVOID DANGEROUS ENVIRONMENT. Use the sander in a dry, indoor place protected from rain. Keep work area well

lighted.

Place the sander so neither the user or bystanders are forced to stand in line with the abrasive belt or disc.

To avoid injury from unexpected sander movement:

e Put the sander on a firm level surface where there is

plenty of room for handling and properly supporting the workpiece.

Support the sander so it does not rock. Bolt the sander to the floor or work surface if it tends

to slip, walk, or slide during normal use.

To avoid injury or death from electrical shock:

o GROUND THE SANDER. This sander has an approved

3-conductor cord and a 3-prong grounding type plug. Use only 3-wire, grounded outlets rated 120 volts, 15 amperes (amps). The green conductor in the cord isthe grounding wire. To avoid electrocution, NEVER connect

the green wire to a live terminal.

,, Make sure your fingers do not touch the plug's metal

prongs when plugging or unplugging the sander.

To avoid back injury, get help or use recommended casters

when you need to move the sander. Always get help if you need to lift the sander.

NEVER STAND ON TOOL. Serious injury could occur if the

tool tips or you accidentally hit the cutting tool. Do not store

anything above or near the tool where anyone might stand on the tool to reach them.

BEFORE EACH USE:

Inspect your sanderl DISCONNECTTHE SANDER. To avoid injury from accidental starting, unplug the sander, turn the switch off and remove

the switch key before changing the setup, sanding disc or belt or adjusting anything.

CHECK DAMAGED PARTS. Check for:

,, alignment of moving parts, ,, binding of moving parts,

= broken parts,

• stable mounting, and o any other conditions that may affect the way the sander

works.

WARNING: The 2-1/2" machine pulley and the 2" motor

pulley furnished will run the disc at about 2700 RPM and the

belt at about 2100 FPM (Feet Per Minute) when used with a

3450 RPM motor. To avoid throwing of work or broken

sander fragments, never substitute or interchange these

pulleys to increase this speed.

If any part is missing, bent, or broken in any way, or any elec-

trical parts don't work properly, turn the sander off and

unplug the sander. REPLACE damaged, missing, or failed

parts before using the sander again. MAINTAIN TOOLS WITH CARE. Keep the sander clean for

best and safest performance. Follow instructions for lubri-

cating.

REMOVE ADJUSTING KEYS AND WRENCHES from tool before turning it on.

To avoid injury from jams, slips or thrown pieces:

• USE ONLY RECOMMENDED ACCESSORIES. (See

page 22.) Consult this Owner's manual for recom- mended accessories. Follow the instructions that

come with the accessories. The use of improper ac- cessories may cause risk of injuryto persons.

Adjust table to clear the sanding surface by no more

than 1/16 of an inch.

,, Make sure all clamps and locks are tight and no parts

have excessive play.

• KEEPWORK AREA CLEAN. Cluttered areas and benches invite accidents. Floor must not be slippery.

To avoid burns or other fire damage, never use the sander near flammable liquids, vapors or gases.

Plan ahead to protect your eyes, hands, face, ears.

KNOW YOUR SANDER. Read and understand the owner's manual and labels affixed to the tool. Learn its application

and limitations as well as the specific potential hazards pecu- liar to this tool.

To avoid injury from accidental contact with moving parts, don't do ]ayout, assembly, or setup work on the sander while

any parts are moving. AVOID ACCIDENTAL STARTING. Make sure switch is "OFF'"

before plugging sander into a power outlet.

safety instructions for belt and disc sander

Plan your work. , • Use extra supports (tables, saw horses, blocks, etc.) for

USETHERIGHTTOOL Don t forcetoo[or attachment to doa any workpieces large enough to tip when not held down job it was not designed to do. to the table _oD,

CAUTION:Thismachineisnotdesignedforheavydeburring • NEVER use another person as a substitute for a table operations. When finishing metals, sparks or hot fragments extension or as additional support for a workplace that could cause a fire. To avoid this. disconnect any dust col- is longer or wider than the basic sander table, or to help

lectieg hose fromthesander. Also, remove all traces of wood dustfrom inside dust traps in the sander. = When finishing on the Disc, always press the workpieca

Dress for safety, side coming up from under the table could damage the

WEAR YOUR hands and throw it.

Any power sandercan throw foreignobjects intothe eyes. This can cause permanent eye damage. Wear safety goggles (not glasses) that cornpty withANSI Z87.1. Everyday eyeglasses

have only impact resistant lenses. Theyare not safety glasses.

Safety goggles are available at Sears retail catalog stores. Glasses or goggles not in compliance with ANSI Z87.1 could

seriously hurt you when they break,

= Do not waarioosa clothing, gloves, neckties orjewelry

(rings. wrist watches). Tney can get caught and draw

you into moving parts.

= Wear nonslio footwear.

- Tie back long hair.

• Roll long sleeves above the elbow. Make sure the sanding disc turns counterclockwise before

- Noise levels vary widely. To avoid possible hearing dam- using the sander. age, Wear ear plugs ormuffs when using sander for hours KEEP CHILDREN AWAY. Keep all visitors a safe distance from

at a time. the sander. Make sure bystanders are clear of the sander and

o Sanding operationaare usually dusty. Wear a dust mask workpiece.

along with the safety goggles. DON'T FORCE TOOL. It will do the job better and safer at its

Inspect your workpieoe, designated rate. Press the workeiece against the sanding

Make sure there are no nails or foreign objects in the part of material only hard enough to let it sand without bogging the workDiece to be sanded, down or binding.

Plan your work to avoid THROWBACKS--when the work- piece catches on the sanding belt or disc and is torn from

your hands.

• Make sure there's no debris between the workpiece and its supports.

• When sanding irregularly shaped workpiecas, plan your work support so it wit{ not slip and be pulled from your

hands.

• Use extra caution with large, very small or awkward pieces:

• Never use this tool to finish pieces too small to hold by hand.

feed support or pull the workp=eca,

against the "'Down" side of the disc. Sanding against the

work by making it "chatter," or tear the work from your

• Sand only one workpiece at a time,

• Clear everything except the workoiece and related sup- port devices off the table before turning the sanaer on.

Plan the way you will hold the workpiece from start to finish.

Avoid awkward oeerations and hand positions where a sud- den slip could cause fingers or hand to move into a sanding surface. Keep fingers away from where the belt goes into the

dust trap, DON'T OVERREACH. Keep good footing and balance

Keep your face and booy to one side. out of line with a pos- sible throwback

WHENEVER SANDER IS RUNNING.

WARNING: Don't let familiarity (gained from frequent use of your belt and disc sander} cause a careless mistake. A care-

less fraction of a second is enough to cause a severe injury. Before starting your cut, watch the sander while it runs. If it

makes an unfamiliar noise or vibrates alot, stop immediately. Turn the sander off. Unplug the sander. Do not restart until

finding and correcting tee problem.

Before freeing any jammed material:

• Turn switch "ORE"

• Unplug the sander.

• Wait for all moving parts to stop.

To avoid throwback of the workpiece, use work!_iece supports for all flat surface sanding.

BEFORE LEAVING THE SANDER:

Wait for all moving parts to stop, Make workshop child-proof. Lock the shoo. Disconnecl

master switches. Remove the yellow switch key Store it away from children and others not qualified to use tne tool.

electrical requirements

CONNECTING TO POWER SOURCE OUTLET

This machine must be grounded while in use to protect the operator from electric shock.

Plug power cord into a 120V properly grounded type outlet protected by a 15-amp. dual element time delay or Circuit-

Saver fuse or circuit breaker.

If you are not sure that your outlet is properly grounded,

have it checked by a qualified electrician.

WARNING: DO NOT PERMIT FtNGERSTO TOUCH THE

TERMINALS OF PLUGS WHEN INSTALLING OR RE- MOVING THE PLUG TO OR FROM THE OUTLET.

WARNING: IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN INCUR THE POTENTIAL HAZARD OF ELECTRICAL SHOCK. PARTICULARLY WHEN USED IN DAMP LOCATIONS IN PROXIMITY TO PLUMBING.

IF AN ELECTRICAL SHOCK OCCURS THERE IS THE POTENTIAL OF A SECONDARY HAZARD SUCH AS

YOUR HANDS CONTACTING THE ABRASIVE BELT OR DISC.

If power cord is worn or cut, or damaged in any way, have it replaced immediately.

Your unit is wired for 120 volts and has a plug that looks like the one shown below.

If the outlet you are planning to Use for this power tool is of the two prong type DO NOT REMOVE OR ALTER THE GROUNDING PRONG IN ANY MANNER, Use an adapter as shown and always connect the grounding lug to

known ground.

It is recommended that you have a qualified electrician

replace the TWO prong outlet with a properly grounded

THREE prong outlet.

A temporary adapter as shown below is available for

connecting plugsto 2-prong receptacles. The green ground-

ing lug extending from the adapter must be connected to a

permanent ground such as to a properly grounded outlet

box,

A temporary adapter as illustrated is available for connecting

plugs to 2-prong receptacles. The temporary adapter should be used only until a properly grounded outlet can be

installed by a qualified electrician.

NOTE: The adapter illustrated is for use only if you already have a properly grounded 2-prong receptacle.

The use of any extension cord will cause some loss of power. To keep this to a minimum and to prevent over-

heating and motor burn-out; use the table below to deter- mine the minimum wire size (A.W.G.) extension cord. Use

only 3 wire extension cords which have 3-prong grounding

type plugs and 3-pole receptacles which accept the tools

plug.

GROUNDING LUG

3-PRONG PLUG

PROPERLY GROUNDED

/n Ul

OUTLETs, 4

/Do l

This power tool is equipped with a 3-conductor cord and

grounding type plug, approved by Underwriters' Labora-

tories and the Canadian Standards Association. The ground

conductor has a green jacket and is attached to the tool hous=

ing at one end and to the ground prong in the attachment plug at the other end.

This plug requires a mating 3-conducto{ grounded type out- let as shown.

GROUNDING PRONG

I _ MAKE SURE THIS IS

3-PRONG _ _ I _ " j} CONNECTED TO A

__.,,,_r__..._3_ [_ ]1 2-PR ONG

/ _ RECEPTACLE

ADAPTER

Extension Cord Length

Wire Size A.W.G.

0-25Ft ................... 16

26-50Ft ................... 14

51-100 Ft .................. 12

CHECK MOTOR ROTATION

Place the motor on your workbench or on the floor. Standing clear of the motor shaft, plug the motor cord into a

properly grounded outlet. Notice the rotation of the shaft. As you look directly at the motor shaft it should be turning in

the counterclockwise direction _ . tf the motor shaft is turning counterclockwise, remove the plug from the power

outlet and continue the assembly procedures. If the motor is turning clockwise, remove the plug from the power outlet and contact your Sears Store immediately,

CONTENTS

SAFETY INSTRUCTIONS FOR POWER TOOLS .............. 2

ADDITIONAL SAFETY NSTRUCTIONS FOR BELT AND

DISC SANDER ............................................................ 3

ELECTRICAL REQU REMENTS .......... 5

Check Motor Rotation .............................................. 5

UNPACKING AND CHECKING CONTENTS ...................... 6

ASSEMBLY ....................................................................... 7

Assembling Steel Legs ............................................... 8

Mounting Belt and Disc Sander on Steel Leg Set ...,.. 8

Installing Sanding Disc and Dust Trap ....................... 9

Installing Motor, V-Belt Tensioning and Tracking .... 1!

On-Off Switch ........................................................... 12

Installing Work Table ............................................... 14

Installing Abrasive Belt Tensioning and Tracking .... 14

Installing Belt Dust Trap ........................................... 15

Installing Backstop ..................................... 16

GETTING TO KNOW YOUR SANDER ............................. 16

Belt Adjusting Screws ............................................. 17

unpacking and checking

Model 113.225900 Belt and Disc Sander is shipped complete in one carton but DOES NOT INCLUDE Steel

Legs or Motor.

Model 113.225931 Belt and 0isc Sander is shipped

complete in one carton and INCLUDES Steel Legs and

Motor.

Separate all parts from packing materials and check each"

item with Ilustration and "Table of Loose Parts." Make

certain all items are accounted for, before discarding any packing material.

If any parts are m_ss_ng, do not attempt to assemble the Belt and Disc Sander. plug in the power core. or _urn the

switch on until the missing parts are obtained aria

installed correcti V. Using a 112" wrench, remove the plywood attached to

the machine. Save the nuts and bolts and washers. You SHOULD_ NOGAPOROVE,LAPNEREWHEN Wil] need them for attaching the machine to the base SOUARES_L'PPEOOVE"_NDOTTEOPOS,T_ON

contents

3/4"7/16"1/2"WrenchWrenChwrenchMedium_:2Screwdriver_PhilbpsScrewdrlvelC°mbinati°nSquare !i_._Square 3/8" Wrench

Belt Locking Screws ................................................. 17

Work Table Tilt Lock Screw ..................................... 17

Backstop Lock Screw ............................................... 18

Belt Table Locking Bolts .......................................... 18

Belt Table Stop ......................................................... 18

BASIC OPERATION ......................................................... 19

Surface Finishing on tne Abrasive Belt ................... 20

End Finishing on the Abrasive Belt .......................... 20

Finishing Curved Edges on the Abrasive Belt .......... 21

Finishing Small End Surfaces and Curved Edges

on Disc ................................................................ 21

MAINTENANCE ................................................................ 22

Motor Maintenance and Lubrication ......................... 22

LUBRICATION .................................................................. 22

Recommended Accessories .................................... 22

TROUBLESHOOTING ...................................................... 23

REPAIR PARTS ................................................................ 25

Motor Connections ................................................... 29

TOOLS NEEDED - - - ,

COMBINATION SQUARE MUST BE TRUE.

DRAW LIGHT J 8OAR° 3/4 THICK

LINE ON BOARO TNIS EDGE MUST B£

AEOf_G THIS EIE)GE I_'_ _ PERFECTLY STRAIGHT

I "N.I

[ q_u

D E

Item ! Table of Loose Parts Qty, j

A V-Belt, 1/2 x 41" . ....................... 1

B Backstop ............................... 1

O Belt, Du_tTrap .......................... 1

D Motor Pulley Belt Guard ................... 1

E Belt Guard Support ....................... 1

F Belt Guard Support Bracket ................ I

G "S'" Clip ............................... 3

H Pan Head Screw, Type 23, 10-32 x 1/2 ........ 3

J Baseand Belt, Table (w/Sanding Belt) ......... t

K Disc Dust Trap .......................... t

L Oust Trap Cover ......................... 1

M Work Table ............................. 1

N Bag (containing the following loose parts)

(Part No. 68035)

Motor Pulley, 2 In. Oia................... 1

Wrench, 1/2" . ......................... 2

5/32 Setscrew Wrench ................... 1

Flat Head Machine Screw 10-32 x 1-3/4 ...... 4

assernbJy

The following parts are included with Model 113.225931

ONLY.

Item

No. Qty.

*Loose Parts Bag Part#68062Containing Following items:

*A Nut, Hex Head1/2-13 ........................ 8

*A Nut Hex 1/4-20 .............................. 32

*B Screw Truss Hd. 1/4-20x 5/8 ................. 32

*C Lockwasher, 1/4 External .................... 32

*D Foot, Leveling .............................. 4

E Motor ...................................... 1

F Leg ......................................... 4

G Channel,Support ........................... 2

H Stiffener, Side .............................. 2

J Stiffener,End ............................... 2

K Support, Motor ............................. 1

P Bracket, Mounting ........................... 1

HAROWABEFORMOUNTINGTOOL& MOTOR

*L Screw,Hex Hd. 5/16-18x 1-1/2 ............... 2

*C Lockwasher Ext. 5/16 ....................... 6

*A Nut,Hex5116-18 ............................ 6

*M Washer11132ID ............................ 6

*N Bolt, Carriage 5116-18x 314 .................. 4

Item Table of Loose Parts Qty.

Pan Head Screw, Type 23 8-32 x 3/8 ......... 5

Fiat Washer, 21/64 x 7/8 x 1/8 .............. 1

Hex, Head Machine Screw 5/16-18 x 1 ........ 1

Screw, M Pan Hd. 10-32 x 9/16 ............. I

Lockwasher No, 10 Int. Tooth .............. 1

Hunger, Cable ........................... 1

0 Owner's Manual ........................... t

P 9" Abrasive Disc .......................... 1

Q Sanding Disc (w/Set Screw) .................. 1

R Belt,Sanding .............................. 1

- Bag Assembly, Outlet (Part No. 68064) (Containing the following loose parts):

S Outlet, on/off Power ...................... 1

T Switch Key ............................. 1

U Bracket, Switch Mounting .................. t

V Screw, Pan Hd. 8 x 3/8 .................... 3

W Lockwasher, 114" . ....................... 2

X Screw; Pan Hd. Machine 1/4-20 x 1/2 ......... 2

F•

N P

1. Assemble the two (2) End Stiffeners and the two 2 Side Stiffeners using four (4) 1/4-20 Truss head

screws. The End Stiffeners are placed On top of each Side Stiffener as shown. Insert screws through the

9/32 inch diameter holes and finger tighten 1/4-20

nutS.

2. Attach the four (4) legs to the side and End Stiffener

using 1/4-20 screws, Iockwashers and nuts as shown.

3. Remove the four (41 Truss head screws which were assembled in Paragraph No. One. Place the two (2 Support Channels as shown, in position align holes in

supports with holes in the Stiffeners, replace

Iockwashers and nuts, Tighten all nuts using 7/16

wrench.

4. Assemble the motor support to steel legs with 1/4-20

screws and nuts. Motor support can be mounted to either end of stand. Tignlen nuts

5. Install leveling feet as shown. To level Leg Set, loosen nut on inside of leg and turn nut on outside to raise or lower feet. Adjust alt four levelers, if necessary, and then tighten nuts on inside of leg.

NOTE: These levelers are not intended for height adjustment.

END STIFFENER HEX NUT

SCREW_ 1 | LOCKWASHER

S,DE ST,FFEN R

STIFFENER

LOCKWASHER

HEX NUT _e

_- _ SUPPORT

_ k _.

_ CH/%NNEL

LEG

SCREW

SIDE STIFFENER

CHANNEL SUPPORT

MOTOR

SUPPORT

/ NUT

LOCKWASHER

LEG

SCREW

WHEN INSTALLING OR MOVING THE SANDER. AVOID DANGEROUS ENVIRONMENT, Use the sander n a

dry, indoor place protected from rain. Keen work area well

lighted.

Place the sander so neither the user nor bystanders are forced to stand in line with the abrasive belt or d sc.

To avoid injury from unexpected sandel movement: = Put the sander on a firm level surface where there is plenty

of room for handling and properly supporting the workpiece.

- Support the sander so it does not rock.

,,Bolt the sander tothe floor or work surfaceif it tends to slip,

walk. or slide during normal use.

To avoid back injury, get help or use recommended casters when you need to move the sander. Always get help if you

need to lift the sander. NEVER STAND ON TOOL. Serious injury could occur if the

too] tips or you accidentally hit the cutting tool, Do not store

anything above or near the toot where anyone might stand on

the tool to reach them.

MOUNTING BELT AND DISC SANDER ON

CRAFTSMAN STEEL LEG SET.

CATALOG NO. 9-22236

MOTOR MOUNT

BRACKET THISSIDE

0 C OOc

NOTE: Forillustrative purposes, the Belt and Disc Sander is

shown mounted on the Craftsman Catalog No. 9-22236

Steel Leg Set. This Leg Set is included with Model No.

113.225931.

o°o°

o o

___c oc

1. )lace the 3elt and Disc Sander on the Steel Legs, position as shown, ane align the mounting qoles n

the feet of the Belt and Disc Sander with those in the

END STIFFENERS marKea with an X n tne Jllustratior !.

NOTE: The abrasive belt is shipped detached. To install the belt on the machine:

1. Loosen both belt LOCKING screws, using the 1/2" wrench furnished with the machine.

2. Turn both of the abrasive belt AJUSTING screws as shown until they stop. Retighten the two belt LOCK-

ING screws so that the idler pulley does not come out

3. Remove the piece of paper,

4. Remove the protective coating, that is applied at the factory, from the belt table. Use any ordinary house-

hold type grease and spot remover.

2. Mount to legs using two 5_16-18 x 2-1/2'" hex head screws, flat washers, externa! Iockwashers. ana hex

nuts.

1/2" WRENCH

WARNING: Never use gasoline, naptha, or similar highly volatile solvents.

NOTE: Do not apply wax to the belt table.

INSTALLING SANDING DISC AND DUST TRAP

1. Loosen the belt table locking bolts behind the mount-

ing bracket using one of the 1/2"" wrenches supplied with your machine.

2. Position belt table vertically and tighten only one of the bolts.

3. Place the V-Belt over the pulley.

4. Attach the switch assembly to the base using the two

screws and washers packed with the switch.

5. Loosen the bolt that you tightened in step 2. Position the belt table horizontally, and tighten both bolts.

BELT ADJUSTING SCREW (ONE ON EACH SIDE)

BELT TABLE LOCKING

WRENCH

SWITCH

ASSEMBLY

assembly

B. Find five 378" Pan Head Self-Treading screws from

among the loose parts.

7. Place Disc Dust Trap on your workbench and screw m five Pan Head "Thread Cutting Screws," 3/8" long. Screw them in all the way.

NOTE: The holes in the Trap are not threaded but the screws are "Thread Cutting Screws" and will cut a thread as they are tightened.

DISC DUST TRAP

R. Find four Flat Head Machine Screws 1-¾" long from

among the loose _arts

9. Attach the Disc Dos1 Trap with four flat head screws !-¾" long.

10. There is a flat spot on the shaft near the end. Rotate the shaft so that the flat spot is facing up.

11 Place the disc on the shaft so that the set screw ts

facmc up. Position the disc so that it is approx, 1/16

rich outward from the edge of the dust trap.

12 Insert the long end of me 532" setscrew wrench

through me hole in the disc housmg and mto the setscrew n the disc. Make sure setscrew _s aligned

with "F ]at" on shaft.

FLAT HEAD SCREWS

1 3/4" LONG

/ /

TRAP

5/32INCH

/--SETSCREW

/ WRENCH

FLAT SPOT

/ONSHAFT

NOTE: After several hours of operation, check for

ooseness of setscrew and ret_gh[er

13. Make certain that the metal disc is free of oil and

grease then peel the backing from the 9" abrasive disc and affix to the sanding disc.

\ \

+ 22 hidden pages