Craftsman 113.213213 User Manual

Save This Manual

For Future Reference

MODEL NO.

113.213213

DRILL PRESSWITH

MAXIMUM DEVELOPED

2 HP MOTOR

Serial

Number
Model and serial number

may be found at the left
side of the head.

You should record both
model and serial number in

a safe place for future use.

YO

SAFETY:

READ ALL

INSTRUCTIONS

CAREFULLY

\

MOTORIZED

20-1NCH

iNDUSTRIAL RATED DRILL PRESS

o assembly

• operating

• repair parts

Sold by SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60195 U.S.A.

Part No. SP5868 Printed in China

FULL ONE YF.AR WARRANTY ON CRAFTSMAN DRILL PRESS

if within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in

material or workmanship, Sears wili repair it, free of charge.

WARRANTY SERVICE iS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SER-
VICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.

This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

SEARS, ROEBUCK AND CO., D/817 WA Hoffman Estates, iL 60195

GENERAL SAFETY iNSTRUCTiONS FOR POWER TOOLS

1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and

labels affixed to the tool. Learn its application and
limitations as well as the specific potentialhazards

peculiarto thistool.

2. GROUND ALL TOOLS 13.
This tool is equipped with an approved 3-conductor

cord and a 3-prong groundingtype plug to fit the

proper groundingtype receptacle. The green con- 14.
ductor inthe cord isthe groundingwire. Never con-

nect the greenwire to a liveterminal,

3. KEEP GUARDS IN PLACE

in working order, and in proper adjustment and

alignment.

4. REMOVE ADJUSTING KEYS AND WRENCHES 16.

Form a habit of checking to see that keys and
adjusting wrenches are removed from tool before

turning it on. 17.

5. KEEP WORK AREA CLEAN

Cluttered areas and benches invite accidents.

Floor must not be slippery due to wax or sawdust. 18.

6. AVOID DANGEROUS ENVIRONMENT

Don't use power tools in damp or wet locations or
expose them to rain. Keep work area will lighted.

Provide adequate surroundingwork space.

7. KEEP CHILDREN AWAY
All visitors should be kept a safe distance from
work area.

8. MAKE WORKSHOP CHILD-PROOF

With padlocks, master switches, by removing

starter keys, or storing tools where children can't
get them.

9. DON'T FORCE TOOL

It will do the job better and safer at the rate for

which itwas designed.

10. USE RIGHTTOOL

Don't force tools or attachment to do a job it was

not designedfor.

11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties, or

jewelry (rings,wrist watches) to get caught in mov-

ing parts. NONSLIP footwear is recommended.

Wear protective hair covering to contain long hair.

Roll long sleeves abovethe elbow. 22.

12. USE SAFETY GOGGLES (HEAD PROTECTION)
Wear safety goggles (must comply with ANSI

Z87.1 ) at all times. Everyday eyeglasses are not
safety glasses. They only have impact resistant
lenses. Also, use face or dust mask ff cutting ope,_

ation is dusty, and ear protectors (pMugsor m_ffsl
during extended periods of operation.

SECURE WORK
Use clamps or a vise to hold workwhen pract_ca_ _t

frees both hands to operate tool.

DON'T OVERREACH
Keep proper footing and balance at all times.

15.

MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest _er_

formance. Follow instructions for lubricating anGi
changing accessories.

DISCONNECT TOOLS

Before servicing; when changing accessories such
as blades, bits, cutters, etc.

AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF' position before P_Jg-

ging in.

USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories. Follow the instructionsthat accompa-

ny the accessories. The use of improper acces-

sories may cause hazards.

NEVER STAND ON TOOL OR ITS STAND

19.

Serious injurycould occur ifthe tool is tipped or if

the cutting tool is accidentally contacted, Do not

store materials above or near thetool such that it is
necessary to stand on the tool or itsstan_ to reach

them.

CHECK DAMAGED PARTS

20.

Before further use of the tool, a guard or other part

that is damaged should be carefully checked to

ensure that it will operate properly and perform its
intended function. Check for alignment of moving

parts, binding or mowng parts, breakage of par_s,
mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged

should be properly repaired or replaced.

DIRECTION OF FEED

21.

Feed work intoa blade or cutter against the direc-

tion of rotation of the blade or cutter only.

NEVER LEAVE TOOL RUNNING UNATTENDED

Turn power off. Don't leave tool until it comes to a

complete stop.

2

additionaj safety instructions for drill presses

SAFETY SIGNAL WORDS a, _fany pa_ of your driit press is missing, maifunc_

DANGER: means if the s_fet,, informatio_ i,:___ot tic,,,_;_ir_q,,_as been damaged or broken...such as

followed, someone Wttl be serio(,;s_y iniured o_ ktled

&_ WARNING: means if the safety _formatio_ s not

followed, someone Coutd be ser o _s_y ir_iu_ed o_
kitted.

CAUTION: means if the safety ir#ormat or_ is _ot

followed, someone May be iniured.

WARNgNG: For your own safe_,, do r_ot attempt
to operate your drill press until it is completely

assembled and installed according to the
instructtons.,.and untiR you have read and under-

stand the foNowlng:

1. General Safety instructions for Power Tools ....... 2

2. Getting to Know Your Drill Press ......................... 19

3. Basic Drill Press Operation ................................... 25

4. Adjustments ........................................................... 28

5, Maintenance ............................................................ 30

6. Stability of Drila Press

If there is any tendency of the drill press to titt or
move during any use, boit it to the fio_:,_ror a flat pi_;<.e
of 1/2" exterior plywood _arge enough to stabiiize the

dritt press. Bolt the p{ywood to the under side of the
base, so its extends at least 2' beyond aft sides.

Make sure the plywood won't trip the operator. Do

not use pressed wood panels ,they can break

unexpectedly.

7. Location

Use the drill press in a well Ht area and or_ a level
surface ctean and smooth enough to reduce the risk
of trips, slips, or fails. Use it where nerther the opera-

tor nor a casual observer is forced to stand in line
with a potential kickback.

8. Kickback

Kickback is the grabbing of the workpiece by the

rotating tool. The workpiece can be thrown at very

high speed in the direction of rotation. THiS CAN

CAUSE SERIOUS INJURY To redu_ the possibi_
of injury from kickback:

Clamp the workpiece firmly to the table whenever
possible.

Buffing or sanding wheels or drums should be

contacted on the side moving away from you, not
the side moving toward .you.

Use only recommended accessories and fottow
the instructions supplied w_th the accessory.

9. Protection: Eyes, Hands, Face, Ears and Body.

WARNING: To avoid being pulled into the

spinning tool:

1. Do NOT wear:

- gloves

- necktie

- loose c|othlng

- jewelry

2, Do tie back long hair

the motor s `w'itch' or other operating control, a
safety device or the power cord, turn the driti

press off acid unplug it until the particular part is
properly repaired or replaced.

b,

Never place your fingers in a position where they
c.ou_d oontz_ct the drill or other cutting tool if the

wompiece should unexpectedly shift or your hand
s;_oL._id5_ip.

i_:._avoid iniurY from parts thrown by the spring,

C,

foI_ow instructions exactly as given and shown in
adjustir-_g spring tension of quill.

_'b preve;r_t the workpiece from being torn from
your ha_ds, spinning of the tool, shattering the

too_ o_ being the'own, always properly support
you_ w_:_rk so it won't shift or bind on the tool:

Aiways position BACKUP MATERIAL (use
beneath the workpiece) to contact the left side

of the coturT_n.

.....Whenever possible, position the WORKPIECE

to contact the left side of the column-if it is too

short or the table is tilted, clamp solidly to the

tab!e. Use table slots or clamping ledge

around the outside edge of the table.

.... When using a drill press VISE, always fasten it

to the table.

.....Never do any work "FREEHAND" (hand-hold-

ing workpiece rather than supporting it on the

tab_e), except when polishing.

.. Securely lock Head to Column, table Support

to Column, and Table to Table Support before
operating drill press.

......Nerv,er move the Head or Table while the tool is

running.

.....Before starting the operation, jog the motor

swit:cf_ to make sure the drill or other cutting
too! does not wobble or cause vibration.

.... if a workpiece overhangs the table such that it

wilt fat! or tip if not held, clamp itto the table or
provide auxiliary support.

.....Use fixtures for unusual operations to ade-

quatefy hold, guide and position workpiece.

..,-.Use the SPINDLE SPEED recommended for

the specific operation and workpiece materi-
aFcheck the inside of the Belt Guard for

drifting ir_formation; for accessories, refer to the
instructions provided with the accessories.

e. Never climb on the drill press Table, it could

break or pu_ the entire driUpress down on you.

f. Turn the motor Switch Off and put away the

Sw_tchKey when leaving the drill press.

g. TOavoid }njury from thrown work or toot contact,

do NOT perform layout, assembly, or setup work
or_the tab4e _ile the cutting tool is rotating.

10; Use only accessories designed for this driBI

press to avoid serious injury from thrown bro-

ken parts or work pieces.

a. When cuttinglarge diameterholes:

Clamp the workpiece firmly to the table.

Otherwise the cutter may grab and spin itat high
speed.

Use onlyone piece, cup-type,hole cutters.
DO NOT use fly cuttersor mufti-part hole cutters

as they can come apart or become unbalancedin
use.

Keep speed below 1,500 RPM.

b. Drum sanders must NEVER be operated on this

drillpress at a speed greater than 1800 RPM.

c. Do not install or use any drillbit that exceeds 7" in

length or extends 6" belowthe check jaws. They
can suddenlybend outward or break.

d. Do not use wire wheels, router bits, shaper cut-

ters, circle (fly) cutters or rotary planers on this
drillpress.

11. Note the Follow the Safety Warnings and

instructions that Appear on the Panel on the

Right Side ofthe Head:

12. This Drill Presshas 12 speeds as listed below:
150 RPM 1150 RPM

260 RPM 1550 RPM
300 RPM 1840 RPM

440 RPM 2220 RPM
490 RPM 2950 RPM

540 RPM 4200 RPM

See inside of belt guard for specific placement of
belt on pulleys.

13. Think Safety. Safety is a combination of operator
common sense and alertness at all times when the

drill press is being used.

WARNING: Do not allow familiarity (gained from
frequent use of your drill press) to become com-

monplace, Always remember that a careQess
fraction of a second is sufficient to inflict severe

injury.

The operations of any power tool can result in foreign

objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles that

comply with ANSI Z87.1 (shown on Package) before
commencing power tool operation, Safety Goggles are

available at area stores.

WEAR YOUR

O

, WARNING

®

4

glossary of

1. Workpiece 4.

The item on which the cutting operations is being

performed.

2. DriU Bit or Drill

The cutting tool used in the drill press to make holes

in a workpiece.

3. Backup Material
A piece of wood placed between the workpieceand

table.,.it prevents wood in the workpiecefrom splin-
tering when the drillpasses throughthe backside of
the workpiece...also prevents drilling into the table

top.

table of contents

terms

Revolution Per Minute {R.RM.)

The number ofturns completed by a spinningobject

in one minute.

5, Spindle Speed

The RPM of the spindle.

6. Backlash - The amount of handle movement or play
between adjacent moving parts.

Page

Warranty.......................................................................... 2

General Safety Instructionsfor Power Tools..................2

AdditionalSafety Instructionsfor Drill Presses ..............3

Glossary ofTerms........................................................... 5

TableofContents............................................................ 5

MotorSpecificationsand Electrical

Requirements............................................................. 6

Unpacking and Checking Contents ................................ 7

List of Loose Parts .......................................................... 8

Location and Function of Controls ................................. 9

Assembly ...................................................................... 10

Tools Needed ........................................................... 10

Assembly of Column and Base ............................... 10

Assembly of Elevation worm Gear and Table

Crank ...................................................................... 10

Installing the Table/Support Assembly ..................... 11

Installing the Head ................................................... 13

Mounting Motor ........................................................ 14

Installing Motor Pulley .............................................. 14

Installing and Tensioning Belt .................................. 14

Installing Belt Guard Knob ....................................... 15

Motor Connections ................................................... 16

Installing Feed Handles ........................................... 16

Installing the Chuck.................................................. 16

Installing Light Bulb.................................................. 18

Bevel Scale .............................................................. 18

Page

Getting to Know Your Drill Press .................................. 19

Spindle Speeds ........................................................ 20

Feature Description .................................................. 20

On-Off Switch ........................................................... 21

Drilling to a Specific Depth ....................................... 22

Locking Chuck Desired Depth .................................22

Removing the Chuck and Arbor ..............................23

Re-Installing the Chuck and Arbor ........................... 24

Basic Drill Press Operation .......................................... 25

Installing Drill Bits in Chuck ...................................... 26

Positioning Table and Workpiece ............................ 26

Tilting Table .............................................................. 27

Hole Location ........................................................... 27

Feeding .................................................................... 27

Adjustments .................................................................. 28

Quill Return Spring................................................... 28

Quill Bearing Adjustment .........................................29

Maintenance ................................................................. 30

Lubrication .................................................................... 30

Recommended Accessories ........................................ 30

Trouble Shooting .......................................................... 31

Repair Parts .................................................................. 32

5

motor specifications and electrical requirements

MOTOR SPECiFiCATiONS

This drillpress is designed to use a 1725 RPM motor
only. Do not use any motor that runsfaster than 1725

RPM. It iswired for operation on 110-120 volts, 60 Hz.
alternatingcurrent.

WARNING: To avoid injury from unexpected

startup, do not use blower or washing machine
motors or any motor with an automatic reset
overload protector.

CONNECTING TO POWER
SOURCE OUTLET

This machine must be grounded while inuse to protect

the operator from electric shock.

Plug power cord into a 110-120V properly grounded
type outlet protected by a 15-amp, dual element time
delay fuse or circuit breaker.

NOT ALL OUTLETS ARE PROPERLY GROUNDED.

IF YOU ARE NOT SURE THAT YOUR OUTLET, AS

PICTURED BELOW, IS PROPERLY GROUNDED,
HAVE iT CHECKED BY A QUAUFIED ELECTRICIAN.

This power tool is equipped .with a 3-conductor cord

and grounding type plug, approved by Underwriters'
Laboratories and the Canadian Standards Association.

The ground conductor has a green jacket and is
attached to the tool housing at one end and to the
ground prong in the attachment plug at the other end.

This plug requires a mating 3-conductor grounded type

outlet as shown.

ff the outlet you are planning to use for this power tool
is of the two prong type, DO NOT REMOVE OR

ALTER THE GROUNDING PRONG IN ANY MANNER.

Use an adapter as shown and always connect the
grounding lug to known ground.

It is recommended that you have a qualified electrician
replace the TWO prong outletwith a properly grounded
THREE prong outlet.

An adapter as shown below is available for connecting

plugs to 2-prong receptacles

WARNING: The green grounding lug extending
from the adapter must be connected to a per-

manent ground such as to a properly grounded
outlet box.

WARNING: To avoid electric shock, do not
touch the metal prongs on the plug, when

installing or removing the plug to or from the
outlet.

WARNING: Failure to properly ground this
power tool can cause electrocution or serious
shock, particularly when used in damp loca-
tions, or near metal plumbing, if shocked, your

reaction could cause your hands to hit the cut-

ting tool.

If power cord is worn or cut, or damaged in any
way, have it replaced immediately to avoid

shock or fire hazard.

3-PRONG

PLUG

GROUNDING LUG

SCREW

3-PRONG __\ _ MAKE SURE THIS IS

RECEPT.CLE

ADAPTER

NOTE: The adapter illustrated is for use only if you
already have a propedygrounded 2-prongreceptacle.

NOTE: Make sure the proper extension cord is used
and is ingood condition.

The use of any extension cord willcause some loss of

power.To keep this to a minimumand to prevent over-
heating and motor burn-out, use the table below to

determine the minimum wire size (A.W,G.) extension
cord. Use only 3 wire extension cords which have 3-

prong grounding type plugs and 3-pole receptacles
whichaccept the toolsplug.

GROUNDING

PRONG

ALWAYSUSE A

PROPERLYGROUNDED

OUTLET

Your unit isfor use on 120 volts, it has a plug that looks
likethe one above.

Extension Cord Length Wire Size A.W.G.

0-25 Feet 16

26-50 Feet 14

WARNING: To avoid injury from unexpected
starting or electrical shock, do not plug the
power cord into a source of power. This cord
must remain unplugged whenever you are
working on the drill press.

Model 113.213213 Drill Press is shipped complete in
one box.

1. Unpacking and Checking Contents
a. Separate all "loose parts" from packaging materi-

als and check each item with "Table of Loose
Parts" to make sure all items are accounted for,

before discarding any packing material. Some
loose parts are contained inside the belt guard.

Open the belt guard cover to find them.

WARNING: if any parts are missing, do not
attempt to assembDe drill press, plug in the

power cord, or turn the switch on until the
missing parts are obtained and are installed
correctly.

2. Remove the protective oil that is applied to the table
and column. Use any ordinary household type
grease and spot remover.

WARNING: To avoid fire or toxic reaction, never
use gasoline, naptha or simiSar highly volaUle

solvents to remove protective oil.

3. Apply a coat of paste wax to the table and column to
prevent rust. Wipe all parts thoroughly with a clean

dry cloth.

TABLE OF LOOSE PARTS

Rtem

G

* Number varies; bags can contain other smaller bags.

Note: To make assembly easier keep contents of each
bag together and separate from contents of other bags.

Part Name Qty.

A

Table/Support Asrn............................................ 1

B

Column Support Asm ........................................ 1

C

Owner's Manual ................................................. 1

D

Motor .................................................................. 1

E

Box of Loose Parts ............................................. *

F

Base ................................................................... 1

Head Asm .......................................................... 1

H

Bag of Loose Parts ............................................ 1

G

E

List of loose parts in the box and bags

M8 x 1.25-20 Long

Hex head bolt (4)

M5 x 0.8 - 12 Long

Pan head screw (1)

(_ M8x16x1.6

Q M8 x 1.25 hex nut (4)

Flat washer ,(8)

Clamp-column Lock (1)

M12 x 1.75 - 40 Long
Hex head bolt (4)

nk (With Set Screw) (1)

Handle crank (1)

e (3)

(_p M3 Hex "L" wrench (1)

M4 Hex "L" wrench (1)

M5 Hex "L" Wrench (1)

(_ M6 Hex "1_"Wrench (1)

Elevation Worm
Gear Shaft (1)

_ Key-Dritt (1)

Knob (1)

Key chuck (1)

__ Chuck (1)

_ Pulley-motor (With Set Screw) (1)

Idler Pulley Assembly (1)

Belt '_" A29 (1)

J __= Key-switch(1)

Belt "V" A33 (1)

location and function of controls

It

BELT TENSION LOCK HANDLES...Tightening

handles locks motor bracket support and BELT
TENSION HANDLE to maintain correct belt dis-
tance and tension.

2. BELT TENSION HANDLE...Turn handle counter
clockwise to apply tension to belt, turn handle

clockwise to release belt tension.

3. HEAD LOCK SET SCREWS...Lock the head to
the column. ALWAYS have them locked in place

while operating the drill press.

4. FEED HANDLE...For moving the chuck up or
down. One or two of the handles may be removed

if necessary whenever the workpiece is of such

unusual shape that it interferes withthe handles.

5. TABLE CRANK...Tum clockwise to elevate table.
Support lock must be released before operating

crank.

6. CHUCK KEY...Used to tighten drill in the chuck
and also to loosen the chuck for drill removal.

7. CHUCK...Holds drill bit or other recommended
accessory to perform desired operations.

8. DEPTH SCALE...AIIows operator to adjust drill
press to drill to a desired depth.

9. DRILL "ON-OFF" SWITCH...Tums drillpress on
and off...also used to lock drill press in off position.

10. UGHT "ON=OFF" SWITCH...Turns the light on
and off.

11. DEPTH SCALE LOCK...Locks the depth scale at
selected depth.

12. SPRING CAP...Provides means to adjust quill

springtension.

13. TABLE LOCK PIN...Acts as an indexing pin to
locate the table at a 90 ° angle to the drill and

chuck.

14. TABLE BEVEL LOCK...Locks the table in any

position from 0o-45°.

15. BEVEL SCALE...Shows degree table is tilted for

bevel operations. Scale is mounted on side of arm.

18. SUPPORT LOCK..,Tightening locks table support

to column. Always have it locked in place while
operating the Drill Press.

11

assembUy

WARNING: For your own safety, never connect

[ plug to power source outlet until all assembly

_ steps are completed.

- TOOLS NEEDED

MEDIUM

SCREWDRIVER

8-INCH ADJUSTABLE

WRENCH

base, table, or drill press head from the carton.

I WARNING: To avoid back injury,get help to lift the

COMBINATION

SQUARE

ASSEMBLY OF BASE/COLUMN

1. Positionbase on floor.
2_ Remove protective sleeve from column tube and dis-

card. Place column assembly on base, and align
holes in column support with holes inbase.

3. Locate four (4) 12mm Dia. x 40mm long bolts among
loose parts bag.

4. Install a bolt in each hole through column support
and base and tighten with adjustable wrench.

COMBINATION SQUARE MUST BE TRUE.

Check its accuracy as illustrated below.

STRAIGHT EDGE OF

DRAW LIGHT
LiNE OH BOARD
ALONG

BOARD 3/4" THICK-
THIS EDGE MUST BE

PERFECTLY STRAIGHT

F

SHOULD BE OVERLAP WHEN
SQUARE IF FLAPPED OVER IN DOTTED POSITION

i

!

12rnm DIA:X 40turn LONG BOLT

COLUMN

SUPPORT

ASSEMBLY OF ELEVATION WORM GEAR AND TABLE CRANK

1. Find elevation worm gear shaft, the crank handle
and table crank inthe loose parts bag. Insert the ele-
vation shaft into the table support and extend the
shaft through the opening as far as possible. The

crank is to be installed on the elevation worm gear
shaft, the set screw is to be aligned with the fiat por-
tion of the shaft. The crank is to be positioned as
close to the arm support as possible, then tighten set

screw with a 3mm HEX "L" wrench. See illustration.

2. Screw the crank handle intothe table crank as illus-

trated. Use an adjustable wrench to tighten the crank
handle securely.

TABLE SUPPORT

10

ASSEMBLY

._ ELEVATION WORM

GEAR SHAFT

TABLE

INSTALLATION OF TABLE/SUPPORT

ASSEMBLY AND HARDWARE

3. Loosen setscrew in column collar with 3mm HEX "L"
wrench and remove collar and rack from column.

w

0°, !,,.°

4. With long smooth end of rack pointing upward, slide
rack down through large round opening in table sup-

port. Engage rack in gear mechanism found inside

opening of table support.

SPECIAL NOTE: This step can be made easier to
complete if you remove the table from the table sup-
port. To do so, following the instructions listed under the

heading "bevel scale" in this section of the manual and
remove the table lock pin and table bevel lock.

COLLAR

5. While holding rack and table support in an engaged
position slide both down over column. Slide rack

down column until rack is positioned against lower
column support.

11

,i

TABLE

COLUMN

SUPPORT

ASSEMBLY

TABLE

SUPPORT

TABLE

RACK

LOWER

sCOLUMN

UPPORT

6. Replace column collar (bevel side down) and posi-
tion it over rack. Tighten set screw in collar with 3mrn

HEX %" wrench. Rotational position of set screw is
not important. Collar must sit loosely over rack and
must not be angled on the column. Only tighten set
screw enough to keep collar in place; rack should
still slide freely in collar when the table is swung to

the left or right around the column.

NOTE: To avoid column tube or collar damage, do not
over tighten setscrew.

COLLAR

RACK

ROTATIONAL
POSITION OF

SET SCREW IS

NOT IMPORTANT

GEAR

MECHANISM

7. Locate the supportlock inloose parts bag.

8. Install support lock from left side into table support
and tighten by hand.

9. Check "Gap" or clearance between table crank and

table support. If the "Gap" is larger than 1/32 of an

inch,crank backlashcan be minimized.

To minimize crank backlash, tighten support lock

(shownabove), rotate elevation worm shaft clockwise,

then assemble table crank tight against table support
and tightenset screw.

SUPPORT

LOCK

COLUMN

\

TABLE

SUPPORT

TABLE

SUPPORT

CHECK"GAP"

ROTATE

ELEVATION

WORM SHAFT

CLOCKWISE

12

TABLE

CRANK

iNSTALLiNG THE HF_AD

CAUTION: To avoid back injury, get help in lift-
ing the head.

1. Remove protective bag from head assembly and dis-
card. Carefully lift head above column tube and slide

it onto column making sure head slides down over
column as far as possible. Align head with table and

base.

2. Using a 5mm HEX "L" wrench, tighten the two head
lock set screws on the right side of the head.

.... .L

HEAD
LOCK

SET

SCREWS

13

MOUNTING MOTOR

1. Locate four (4) 8mm Dia. x 20mm long hex head y
bolts, eight (8) flat washers, and four (4) hex nuts

among loose parts.

2. Put a fiatwasher on each bolt.

3. Install hex head bolts through motor bracket on

head.

4. Place motor in position so motor base slots line up

with motor bracket slots. Install fiat washers and hex
nuts as illustrated. (Do not tighten)

5. Motor shaft should be as close as possible to center
of round opening in belt guard.

8mmDia.x 2_m LONGBOLT

HEXNUT

FLAT WASHER

INSTALLING MOTOR PULLEY

1. Find the motor pulley in loose parts bag.

2. Slide pulley onto motor shaft. Line up the flat surface
on the motor shaft with the set screw in pulley.

3. Make sure the pulley does not rest on the lower
guard.

4. Tighten the set screw using a "4" mm Hex "L"
wrench.

BOLT

MOTOR

BRACKET

MOTOR

BASE

FLAT HEX

WASHER NUT

MOTOR

PULLEY

SET SCREW

FLAT

_ SURFACE

INSTALUNG AND TENSIONING BELT

WARNING: To avoid injury due to accidental
starting always turn drill press off and remove
switch key before making belt adjustments.

1. Place a straight edge such as a piece of wood,
metal, orframing square across the top of pulleys.

2. Move the motor upward until the pulleys are in line.
"13ghtenthe motor mount nuts using an adjustable

wrench.

NOTE: To avoid rattles or other noise, motor frame
must not touch lower belt guard.

3. Release Belt Tension Lock handles located on each
side of Drill Press head by turning them counter-

clockwise.

4. LoosenBelt Tension handle by turningclockwise.

STRAIGHT EDGE

t, 2

0001

LOWER BELT MOTOR

BELT TENSION MOUNT MQTQR

GUARD LOCK NUTS

HANDLE

• '_' BELT

HANDLE

]"__i TENSION

5. Locate idler pulley assembly in loose parts bag and j _y
place in proper hole.

IDLER PULLEY ASSEMBLY

SPINDLE PULLEY

6. Locate two (2) V-belts inthe loose parts bag.

7. Use speed chart inside belt guard to choose speed
for drilling operation. Install belts in correct position

for desired speed. The longer of the two belts is

always positioned between the spindle pulley and
idler pulley.

NOTE: Refer to chart inside belt guard for
Recommended Drilling Speeds.

8. Apply tension to belt by turning Belt Tension Handle
counter clockwise until belt deflects approximately

1/2 inch by thumb pressure at its center.

9. Tighten Belt Tension Lock Handles.

NOTE: Over tensioning belt may cause motor not to
start or damage bearings.

10. Ifbelt slips while drilling, readjust belt tension.

IDLER PULLEY

BELT

TENSION

(} LOCK HANDLE

BELT GUARD KNOB

SCREW

INSTALLING BELT GUARD KNOB

1. To attach belt guard knob, locate knob and 5mm Dia.
x 12mm long pan hd. screw in loose parts bag.

Install screw _nhole located in guard and attach
knob turning until tight.

WARNING: To avoid possible injury keep guard
in place and in proper working order while

operating.

BELT

TENSION

HANDLE I

BELT GUARD KNOB _"_J I

15

MOTOR CONNECTIONS

plug to power source outlet until ag assembly
steps are completed.

1, Open motor connector box cover located on under-

side of motor usingflatblade screwdriver.

WARNING: To avoid electrocution, never con-
nect anything but the ground wire (colored
green) to the green screw.

2. Remove GREEN SCREW and insert throughround
metal terminal on the end of the GREEN wire of

power cord.

3. Reinsert GREEN SCREW in threaded hole that it
was removed from and tighten securely,

4. Insert terminal end of WHITE wire on spade terminal

(next to silver _ marked #4 on the motor. Push

terminal firmly until seated.

5. Insert terminal end of BLACK wire on spade terminal

(next to copper gp__) marked #1 on the motor. Push

terminal firmly until seated.

6. Close motor connector box being sure that power

cord is seated in the "center" strain relief groove and

tighten box cover screws.

7, Do not plug in power cable.

POWER

-/U(((( - CE.TERsT.*,.

-tt'_\\\ J]_'l_ _"1 _ RELIEF GROOVE

\'k._ _ _ _ F'_ \-"" TO TERMINAL #4

BLACK }LACK

GREEN

GROUND

CORD

f

MOTOR

i

1. Locate three (3)feed handles arnong loose parts. _ _,_,_,,_, /
2 Screw the feed handles into the threaded holes in _,,_

/_-'_ FEED

HANDLE

i

INSTALUNG THE CHUCK

1. Clean out the TAPERED HOLE in the chuck, Clean
the tapered surface on the arbor with a clean cloth,

Make sure there are no foreign particles sticking to
these surfaces. The slightest piece of dirt on these
surfaces will prevent the chuck from seatingproper-
ly. This will cause the drill to '_Nobble" or possibly fall
off when drilling.

QUILL

16

CLEAN THIS

ARBOR

SURFACE

2. Slide the chuck up over the arbor as illustrated.

LL

3, Unlock support lock and raise table so its about two SUPPORT

(2) inches below tip of chuck. LOCK

4. Turn chuck sleeve clockwise and open jaws in chuck
completely. \ql

5. Turn feed handles counterclockwise and force chuck
against table until chuck is secure.

CHUCK

SLEEVE

17

_iP

OFCHUCK

iNSTALLiNG UGHT BULB

1. install a light bulb (not larger than 60 watt) into the

socket insidethe head.

BEVEL SCALE

NOTE: The bevel scale has been included to provide a |

quick method for beveling the table to approximate ZE
angles. If precise accuracy is necessary, a square, or UNE_
other precision measuring tool should be used to posi-

tion the table.

1. To use the bevel scale do the following.
a. Using an adjustable wrench, turn the nut (on the

table lock pin) clockwise. This will pull the table
lock pin out of its indexing hole in the table sup-

port.

b. Lcosen the table bevel lock by turning it counter-

clockwise using an adjustable wrench.

c. Move table so desired angle on bevel scale is

straight across from zero line on table support,

d. Retighten the table bevel lock,

2. To return the table to the 90° position do the follow-
ing:

a. Loosen the table bevel lock,
b. Move the table and reinstall the table lock pin into

the indexing hole in the table support, Tap in gen-
tly into place.

c. Tighten the table bevel lock,
d. Tighten the nut (on the table lock pin) finger tight

so it won't vibrate loose.

.ol

BEVEL SCALE

LOCK

PIN

TABLE SUPPORT

TABLE

BEVEL

LOCK

TABLE

18

geeing to know your dritmpress

27

FEED SPRING
ADJUSTMENT

26

FEED SPRING

20

SPRING

CAP

1

BELT GUARD

\

3

BELT TENSION
LOCK HANDLE

25

TABLE BEVEL LOCK

23

BEVEL

SPLINES

(GROOVES)

RACK

(TEETH)

22

TABLE

LOCK PIN

SPINDLE

WEDGE KEY

18

15

DEPTH SCALE

COLUMN

SWITCH

17

DEPTH

SCALE LOCK

16

DEPTH SCALE

INDICATOR

14

BELT TENSION

5

HEAD LOCKS

FEED HANDLE

COLUMN COLLAR

R 9

ACK I ITABLECRANK

2

DRILL

SPEED CHART

3

BELT TENSION
LOCK HANDLE

4

HANDLE

6

7

19

CHUCK KEY

\

QUILL AND SPINDLE ASSEMBLY

INSIDE OF DRILL PRESS

13 COLUMN /.4 !

ARBOR

18

CHUCK

19

This Drill Press has 12 speeds as listed below:

150 RPM

260 RPM
300 RPM

440 RPM

49(] RPM 1840 RPM on pulleys
540 RPM 2220 RPM

1150 RPM 2950 RPM
1550 RPM 4200 RPM

SPINDLE SPEEDS IN R,P.N.

See inside ofbelt guard for specific placement of belts

150

490

1840

260

540

2220

Feature Description

1. BELT GUARD ASSEMBLY...Covers pulleys and
belt during operation ofdrill press.

2. DRILLING SPEED CHART...Speeds can be
changed by placingthe belt in any of the STEPS

(grooves) in the pulleys. See Spindle Speed label

inside belt guard. To determine the approximate
drilling speed, for specific materials, refer to the

table insidethe belt guard.

3. BELT TENSION LOCK HANDLES...Tightening
handles locks motor bracket support and BELT

TENSION HANDLE to maintain correct belt dis-
tance and tension.

4. BELT TENSION HANDLE...Turn handle counter

clockwise to apply tension to belt, turn handle

clockwiseto release belttension. Refer to section
"Assembly-Installing and TensioningBelt",

5. HEAD LOCK...Lock the head to the column.
ALWAYS have them locked in place while operat-
ingthe drillpress.

6. FEED HANDLE...For moving the chuck up or
down. One or two of the handles may be removed

if necessary whenever the workpiece is of such
unusual shape that itinterfereswiththe handles.

7. COLUMN COLLAR...Holds the rack to the col-

umn. Rack remains movable in collar to permit

table support movements.

So

TABLE SUPPORT...Rides on column to support
arm and table.

9.

TABLE CRANK...Turn clockwiseto elevate table.
Support lock must be released before operating

crank.

10. BASE...Supports Drill Press. Foradditionalstabili-

ty, holes are provided in base to bolt DrillPress to
floor. (See "Additional Safety instructions for Drill

Presses.")

11. COLUMN SUPPORT...Supports column, guides
rack, and provides mounting holes for column to

base.

12. RACK...Combines with gear mechanism to pro-

vide easy elevation of table by hand operated table

crank.

3O(}

1150

2950

13. TABLE...Provides working surface to support

workpiece.

14. COLUMN...Connects head, table, and base on a

one-piece tube for easy alignmentand movement.

15. DEPTH SCALE._Shows depth of hole being

drilled.

16. DEPTH SCALE INDICATOR...Indicates drilling

depth selectedon depth scale,

17. DEPTH SCALE LOCK...Locks the depth scale to
selecteddepth.

18. CHUCK...Holds drill bit or other recommended
accessoryto performdesired operations.

19. CHUCK KEY...It isa self-ejectingchuckkey which
will "pop" out of the chuck when you let go of it.
This action isdesigned to helpprevent throwingof

the chuck key from the chuck when power is
turned "ON". Do not use any other key as a substi-
tute, order a new one ifdamaged of lost.

20. SPRING CAP...Provides means to adjust quill

springtension.

21. DRILL "ON-OFF" SWITCH...Has lockingfeature.

THIS FEATURE IS INTENDED TO HELP PRE-

VENT UNAUTHORIZED AND POSSIBLE HAZ-

ARDOUS USE BYCHILDREN AND OTHERS.

22. TABLE LOCK PIN...Acts as an indexing pin to

locate the table at a 90 ° angle to the drill and
chuck.

23. BEVEL SCALE...Shows degree table is tiltedfor
bevel operations,Scale is mounted on topof arm.

24. SUPPORT LOCK...Tightening locks table support

to column. Always have it locked in place while

operatingthe Drill Press.

25, TABLE BEVEL LOCK...Locks the table in any

position from 00-45°.

26. FEED SPRING...Provides tension to feed handle

mechanism.

27, FEED SPRING ADJUSTMENT...AIIows adjust-

mentoftensiontofeed handle mechanism.

2O

440

1550

4200

ON-OFF SWITCH

The On-Off switch has a locking feature. This fea-
ture is intended to help prevent unauthorized and
possible hazardous use by children and others.

Insert KEY into switch.
NOTE: Key is made of yellow plastic.

To turn drill ON, insert finger under switch lever
and pull end of the lever out.

To turndrill OFF, push lever in.

In an emergency: If the drill bit BINDS...STALLS...

STOPS...or tends to tear the workpiece Ioose...you
can QUICKLY turn the drill OFF by hitting the switch
with the palm of your hand.

To lock switch in OFF position, hold switch IN with

one hand and REMOVE key withother hand.

WARNING: For your own safety, always push
the switch "OFF" when drill press is not in

use...remove key and keep it in a safe
place...aiso...in the event of a power failure (all
of your lights go out) or blown fuse or tripped

circuit breaker, turn switch off...Iock it and
remove the key. This will prevent the drill press
from starting up again when the power comes

back on.

21

DRiLLiNG TO A SPECiFiC DEPTH

To drifta BLIND hole(notall the way through)to a given
depth,proceed as follows.

1. Mark the depth of the hole on the side of the work-
piece.

2. Loosen the depth scale lock.

3. With the switchOFF, bringthe drillbit down untilthe

tip or lips of the bitare even withthe mark.

4. -rum the depth scale counterclockwise until it stops
moving.

5. Tighten the depth scale lock.

6. The bit will now be stopped at this depth until the
depth scale is readjusted.

DEPTH

SCALE LOCK

DEPTH SCALE

INDICATOR

DEPTH
SCALE

MARK

ANOTHER WAY- DEPTH SCALE

1. Wdhthe switchOFF, loosenthe depthscale lock.

2. Place workpieceon table. Adjusttableuntiltip of drill

bit isjusta littleabove the top ofthe workpiece. Turn
the depthscale clockwiseto zero.

3. rum the depth scale clockwise untilthe depth scale

indicator pointsto the desired drillingdepth on the
depthscale.

4. Tighten the depth scale lock.

5. The chuck or drill will now be stopped after traveling
downward the distance selected on the depth scale.

LOCKING CHUCK AT DESIRED DEPTH

1. With the switch off-loosen the depth scale lock.

2. Turn the feed handles until the chuck is at the

desired depth. Hold feed handles at this position,

3. Turn the depth scale clockwise until it stops.

4. Tighten the depth scale lock,

5. The chuck will now be held at this depth when the
feed handles are released,

\

DEPTH

SCALE LOCK

SCALE

DEPTH SCALE

INDICATOR

ADJUST TO

DESIRED DEPTH/ /

22

REMOVmNG CHUCK AND ARBOR

I. With the switch OFF, adjust depth scale to hold drill

at a depth of (3) three inches. (See instructionsfor
"Locking chuck at desired depth").

2. Align key holes in spindle and quill by rotating the
chuck by hand. (See illustration)

3. Insert key drift into key holes.

4. Tap key drift lightly until the chuck and arbor fall out
of spindle.

NOTE: Place one hand below chuck to catch it when it

falls out.

SPECIAL NOTE: With the chuck and arbor
removed, morse taper number 3 drills may be used

by installing one directly into the spindae in the
same position normalhj occupied by the arbor.

The same procedures and cautions used when

"reinstalling the arbor and chuck" (see following
page) should be used when installing a morse taper

number 3 driBi. The only exception to this proce-
dure is that you may place a piece of wood on the
table top to prevent damage to the table and dri,,
when they are forced against each other.

SPINDLE KEY

HOLE __

QUILL KL=Y_ -

HOLE

CHUCK

SLEEVE

DRIFT

KEY

CHUCK

SLEEVE

J

CHUCK

BODY

23

RE-INSTALUNG THE CHUCK AND ARBOR

NOTE: The chuck received with this drill press willnot
permitthe use of smallerdiameter drillbits. Foran alter-

nate accessory chuck and key with 1/32" - 5/8" capacity

the following partnumber shouldbe ordered. - Part No.

#8! 7340 (chuck&key).

1. Clean the tapered surfaces onthe arbor and spindle

with a clean cloth. Make sure there are no foreign
particles sticking to these surfaces. The slightest

piece of dirt on these surfaceswill prevent the arbor

from seating properly. This will cause the drill to

"wobble".

2. Slide arbor into spindle on drill press.

3. Push up on chuck/arbor assembly as you rotate
them. You willfeel rectangular end of arborslipintoa

notchinthe spindle.

WARNING: Make sure the rectangular end of
the arbor has slipped into the notch in the

spindle before going on to step 4. Failure to
follow this direction may allow the chuck to

come loose during operation, fly' out, and hit
the operator.

TAPERED SLIRFACE

TAPERED

ARBOR SURFACE

CHUCK

SLEEVE

CHUCK

BODY

4. Unlock support lock and raise table so its about two
(2) inches below tip of chuck.

5, Turn chuck sleeve clockwise and openjaws in chuck

completely.

6, "rum feed handles counterclockwise and force chuck

against table until arbor is secure.

FEED

HANDLE

SUPPORT

LOCK

_POF

CHUCK

CHUCK

SLEEVE

24

CHUCK

basic drill press operation

Followthe following instructions for operating your drill
pressto get the best results and to minimize the likeli-
hood of personal injury.

WARNING: For your own safety, always
observe the safety precautions here and on
pages 2, 3, and 4.

I. Protection: Eyes, Hands Face, Ears & Body

WARNING: To avoid being pulled into the spin-
ning tool-

1. Do NOT wear:

- gloves

- necktie

- loose clothing

- jewelry

2. Do tie back gong hair

a.

If any part of your drill press is missing, malfunc-
tioning, has been damaged or broken...such as
the motor switch, or other operating control, a

safety device or the power cord...cease operating

immediately until the particular part is properly

repaired or replaced.

b.

Never place your fingers ina position where they

could contact the drill or other cutting tool if the

workpiece should unexpectedly shift or your hand

should slip.

c.

To avoid injury from parts thrown by the spring,

follow instructions exactly as given and shown in

adjusting spring tension of quill.

d.

To prevent the workpiece from being torn from

your hands, spinning of the tool, shattering the

tool or being thrown, always properly support your

work so it won't shift or bind on the tool:

- Always position BACKUP MATERIAL (use
beneath the workpiece) to contact the left side

of the column.

- Whenever possible, position the WORKPIECE
to contact the left side of the column-if it is too

short or the table is tilted, clamp solidly to the

table. Use table slots or clamping ledge around
the outside edge of the table.

- When using a drill press VICE, always fasten it
to atable.

- Never do any work "FREE HAND" (hand-hold-

ing workpiece rather than supporting it on the
table), except when polishing.

- Securely lock Head and Support to Column,
and table to support before operating drill

press.

- Never move the Head or Table while the tool is
running.

- Before starting the operation, jog the motor
switch to make sure the drill or other cutting

tool does not wobble or cause vibration.

- If a workpiece overhangs the table such that it
will fall or tip if not held, clamp itto the table or

provide auxiliary support.

- Use fixtures for unusual operations to ade-

quately hold, guide and position workpiece.

- Use the SPINDLE SPEED recommended for
the specific operation and workpiece

material-check the panel inside the guard
cover for drilling information; for accessories,

refer to the instructions provided with the
accessories.

e. Never climb on the drill press Table, it could break

or pull the entire drill press down on you.

f. Turn the motor Switch Off and put away the

Switch Key when leaving the drill press.

g. To avoid injury from thrown work or tool contact,

do NOT perform layout, assembly, or setup work

on the table while the Cuttingtool is rotating.

2. Use only accessories designed for this drill press

to avoid serious injury from thrown broken parts
or work pieces.

a. When cutting large diameter holes:

Clamp the workpiece firmly to the table. Otherwise
the cutter may grab and spin it at high speed.

Use only one piece, cup-type, hole cutters.

DO NOT use fly cutters or multi-part hole cutters

as they can come apart or become unbalanced in
use.

Keep speed below 1,500 RPM.

b. Drum sanders must NEVER be operated on this

drill press at a speed greater than 1800 RPM.

c. Do not install or use any drill that exceeds 7" in

length or extends 6" below the chuck jaws. They

can suddenly bend outward or break.

d. Do not use wire wheels, router bits, shaper cut-

ters, circle (fly) cutters or rotary planers on the drill

press.

25

iNSTALLiNG DRILL BiTS iN CHUCK

With the switch off and the key removed, insertdrill bit
intochuckfar enoughto obtain maximumGRIPPING of

the CHUCK JAWS...the jaws are approx. 1" long.
When using a small drillbit do not insert it so far that

thejaws touchthe flutes (spiralgrooves)ofthe drillbit.
Make sure thatthe drill bit is CENTERED In the chuck

beforetighteningthe chuckwith the key.
Tighten the drillbit sufficiently,so that it does not SLIP
while drilling.
Tum the chuck key clockwiseto tighten-counterclock-

wiseto loosen.

POSITiONiNG TABLE AND WORKPIECE

Lock the table tothe column in a positionso that the tip
ofthe drill isjusta little above the topof theworkplece.

Always place a piece of BACK-UP MATERIAL (wood,
plywood...) on the table underneath the workpiece.
This willprevent"splintering" or making a heavy burr on

the underside on the workpiece as the drill bit breaks
through. To keep the backup materialfrom spinningout

of control,itmust contactthe left sideof the column,as
illustrated.

WARNING: To prevent the workpiece or the

backup material from being torn from your
hand while drilling, position them against the

left side of the column, if the workpiece and the
backup material are not long enough to reach

the column, clamp them to the table. Failure to

do this could result in personal injury.

CHUCK KEY

CHUCK

JAWS /

WORKPIECE

BACK-UP

MATERIAL

For small pieces that cannot be clamped to the table,
use a drill press vise (Optional accessory).

to the table to avoid injury from spinning work

I WARNING: The vise must be clamped or bolted

and vise or tool breakage. WORKPIECE

DRILL PRESS

VISE

BOLT OR CLAMP

26 VISE SECURELY

T_LTING TABLE

1. To use the table in a bevel (tilted) position, do the fo_-
lowing:

a. Using an adjustable wrench, turn the nut (on the

table lock pin) clockwise. This will pull the table

lock pin out of its indexing hole in the table sup-
port.

b. Loosen the table bevel lock by turning it counter-

clockwise using an adjustable wrench.

c. Move the table so desired angle on the bevel

scale is straight across from the zero line on the
table support.

d. Retighten the table bevel lock.

WARNING: To avoid injury from spinning work
or tool breakage, always ciarnp workpiece and
backup material securely to table before oper-

ating drill press with the table tilted.

2. To return the table to the 90 ° position do the follow-
ing:

a. Loosen the table bevel lock.
b. Move the table and reinstall the table lock pin into

the indexing hole in the table support. Tap in gen-

tly into place.
c. lqghten the table bevel lock.
d. -lqghten the nut (on the table lock pin) finger tight

so it won't vibrate loose.

BEVEL
SCALE

NUT

TABLE

SUPPORT

TABLE LOCK PIN

HOLE LOCATION

Make a DENT in the workpiece where you want the
hole...using a CENTER PUNCH or a SHARP NATL.

Before turning the switch ON, bring the drill down to the

workpiece lining it up with the hole location.

FEEDING

Pull down on the feed handles with only enough effort
to allow the drillto cut.

Feeding TOO SLOWLY might cause the drill to
burn...Feeding TOO RAPIDLY might stop the

motor...cause the belt or drill to SLIP...tear the work-
piece LOOSE or BREAK the drill bit.

When drilling metal, it may be necessary to lubricate the

tip of the drill with cutting oil or motor oil to prevent burn-

ing of the drill tip.

27

adjustments

WARNING: For your own safety turn switch
"OFF" and remove plug from power source ouUet
before making any adjustments. To avoid injury
from thrown parts due to spring release, follow
instructions carefully, and wear eye goggles.

QUILL RETURN SPRING

1. With the chuck at its highest possible position, turn

the depth scale clockwise until it stops and tighten

the depth scale lock. This will prevent the quill drop-
ping while tensioning the spring.

2. Lower table for additional clearance.

3. Work from leftside of Drill Press.

4. Place screwdriver in lower front notch of spring

cap, and hold it in place while loosening and

removing [outer] nut only.

5. With screwdriver remaining in notch, loosen [inner]

nut (approximately 1/8") until notch disengages

from boss on head. DO NOT REMOVE THIS NUT.

6. Carefully turn screwdriver counter clockwise and

engage next notch in boss. DO NOT REMOVE
SCREWDRIVER.

7. Tighten standard nut with wrench only enough to
engage boss. Do not overtighten as this will restrict

quill movement.

8. Move stop nuts and depth pointer to upper most
position and check tension while turning feed han-
dles.

9. If there is not enough tension on spring, repeat
steps 4-8 moving only ONE notch each time and

checking tension after EACH repetition.

10. Proper tension is achieved when quill returns gently

to full up position when released from 3/4" depth.

11. When there is enough tension after checking,
replace outer nut and tighten to inner nut. BUT do

not overtighten against inner nut.

12. Check quill while feeding to have smooth and unre-
stricted movement. If movement is too tight, loosen

outer nut and SLIGHTLY loosen inner nut until
unrestricted. Retighten outer nut.

NUT

(INNER)

SPRING CAP

PiN

NOTCH

NOTCH

NUT

(OUTER)

28

QUILL BEARING ADJUSTMENT

The front of the head is "Split" which permits an adjust-
ment to be made as the quill and the quill bearing sur-
faces inside of the head become worn after an extend-

ed period of use. The front of the head can be

SQUEEZED together or SPREAD apart by adjusting

three screws.

.

LOOSEN all three screws "A", "B", and C" four

turns using a 6ram HEX "L" wrench.

NOTE: TIGHTENING BOTH SCREWS "A" AND
"B" SQUEEZES HEAD TOGETHER..,TIGHTEN-

ING SCREW "C" SPREADS IT APART.

a. IF QUILL IS TOO TIGHT

(1) TIGHTEN screw "C" until quill is free to move

up and down.

(2) Extend quill halfway down...TIGHTEN screw

"B" until quill is LOCKED.

(3) Carefully LOOSEN screw "B" until quill is free.
(4) TIGHTEN screw "A" only enough so that it

does not lock the quill...quill must move up
and down freely.

b. IF QUILL IS TOO LOOSE

(1) Extend quill halfway down,..TIGHTEN screw

"B" until quill is locked.
(2) Carefully LOOSEN screw "B" until quill isfree.
(3) TIGHTEN screw "A" only enough so that it

does not lock the quill...quill must move up

and down freely.
(4) Screw in remaining screw "C" all the

way.. ,tighten it lightly.

29

maintenance

"OFF" and remove plug from power source outlet

i WARNING: For your own safety, turn switch

before maintaining or lubricating your drill press.

Frequently blow out any dust that may accumulate
insidethe motor.

A coat of automotive type paste wax applied to the

table and column will held to keep the surfaces clean.

WARNING: To avoid shock or fire hazard, if the

power cord is worn or cut, or damaged in any

way, have it replaced immediately.

wiring diagram

lubrication

Allof the BALL BEARINGS are packed with grease at
thefactory.They require no furtherlubrication.

Periodicallylubricate the table elevation mechanism,

the SPUNES (grooves) in the spindle, and the RACK

(teeth of the quill), See "Getting to know your drill
press."

"-T-

GREEN / BLACK

i

MOTOR CORD

i WIRE _ !

w.iT i cK.u=pER

LIGHT

WHITE BLACK

POWER CORD

GREEN

±

Sears Recommends the Following Accessories

Drill Bits......................................................... See Catalog

Drill Press Mortising Kit ................................ See Catalog

Drill Press Vises ........................................... See Catalog

Hole Saw up to 2-!/2" dia. max.................... See Catalog

5 pc, Stop Collar Set .................................... See Catalog

Mortising Chisel and Bits .............................. See Catalog

1/32" -5/8" Dia. Chuck and Key .................See Page 36

Clamping Kit ................................................. See Catalog

15 Piece Drum Sanding Kit..........................See Catalog

Sanding Drums ....................................9-2497 9-2498

Buffing Wheels upto 8" dia. max................. See Catalog

Power Tool Know-How Handbook ......................9-29117

Sears may recommend other accessories not listed in the manual.
See your nearest Sears store or Power and Hand ToolCatalog for other accessories.
Do not use any accessory unless you have received and read complete instructions for its use.

WARNING: Use only accessories recommended |
for this drill press. Using other accessories may

be dangerous.

/

J

30

trouble shooting

before trouble shooting.

i ARNING: For your own safebj, turn switch "OFF" and always remove paug from power source outlet

* CONSULT YOUR LOCAL EMERSON SERVgCE CENTER iF FOR ANY REASON MOTOR WiLL NOT RUN.

TROUBLE

Noisy operation

Drill bit burns

Drill bit leads off...
hogenot round.

PROBABLE CAUSE

1. Incorrect belt tension.

2. Dry Spindle.

3. Loose spindle pulley.

4. Loose motor pulley.

1. Incorrect speed.

2. Chips not coming out
of hole,

3. Dull Drill bit.

4. Feeding too slow.

5. Not lubricated,

1. Hard grain inwood or
lengths of cutting
lips and/or angles
not equal.

2. Bent drill bit.

REMEDY

1. Adjust tension, See section
"Installing and Tensioning Belt."

2. Lubricate spindSe.See "lubrication"
section.

3. Checking tightness of retaining nut on
pulley, and tighten if necessary.

4. Tighten setscrews in pulleys.

1. Change speed. See section "Getting
to Know Your Drill Press"...

spindle speed.

2. Retract drill bit frequently to clear chips.

3. Resharpen drill bit.

4. Feed fast enough to allow dril! bit to cut.

5. Lubricate drill bit. See "Basic Drill Press

Operation" section.

1, Resharpen drill bit correctly,

2. Replace drill bit.

Wood splinters on
underside.

Workpiece torn
loose from hand.

Drill bit binds in
workpiece.

Excessive drill bit
runout or wobble.

Quill returns
too slow or too
fast.

Chuck will not stay
attached to spindle

itfails off when

trying to install it.

1. No "back-up material"
under workpiece,

1, Not supported or

clamped properly.

1. Workpiece pinching drill bit
or excessive feed pressure.

2. Improper belt tension.

1. Bent drill bit.

2. Worn spindle bearings.

3. Drill bit not properly

installed in chuck.

4. Chuck not properly installed.

1. Spring has improper tension.

1. Dirt, grease, or oil on the
tapered insidesurface of
chuck or on the spindles

tapered surface.

1. Use "back-up material"...See basic
drill press operation" section.

1. Support workpiece or clamp it...See
"Basic Drill Press Operation" section.

1. Support workpiece or clamp it...See
"Basic Drill Press Operation" section.

2. Adjust tension...See section
"Installing and Tensioning Belt."

1. Use a straight drilt bit.

2. Replace bearings.

3. Install drillbit properly...See "Basic

Drill Press Operation" section.

4. Install chuck properly...refer to section on
"Installing the Chuck."

1. Adjust spring tension...See section
"Adjustments--Quill Return Spring."

1. Using a household detergent-clean the
tapered surface of the chuck and spindle to

remove all dirt, grease and oil.

31

52

PARTS UST FOR CRAFTSMAN 20" DRILL PRESS

MODEL NO. 113.213213

51

5O

49

=O

4

8

\

46

9

%,

43

42

ro

29

32

41

34

31 30 29

28

27

26

25

24

23

22

/

21

12

19

9

1

10

18

FIGURE 1 PARTS LIST

PARTS UST FOR CRAFTSMAN 20" DRILL PRESS

MODEL NO. 113.213213

Always order by Part Number -- Not by Key Number

fig

FIGURE 1 - PARTS UST

_oy! Part

No_ Description

I 1 1STD835016

I 2 1817317

13 1817688

14 J817336

I 5 I STD852012 *Lockwasher 12mm
I 6 ISTD84!2!71 *Nut-HexM12x1,75

I 7 I 817719 • Motor
I 8 J STD840812 *Nut-HexM8x1.25
I 9 I STD851008 *WasherM8x16x1.6
I 10 1822004 Cord-Motor

I 11 I STD835020 * Screw-Hex Hd M8 x 1,25-20

G)
03

! 12 1817689 Support-MotorBracket
I 13 J817320 Knob-Motor Adjusting

I 14 J817687 Handle-BeltTension

I 15 I 821750 Screw-SocSetM10x 1,5-12

I 16 1817343 Lock-DepthScrew
I 17 I 817300 Guide-Scale

I 18 1817711 Knob

I 19 1817710 Rod

* Screw-Hex Hd M8 x ! ,25-16

Lever=Adjusting
Support-Motor Bracket

MountoMotor

I 20 1822084 Hub

I 21 I 817774-2 Ring-DepthStopw/Scate
I 22 1817303 Pin-Stop

I 23 I 820239-2 Screw-Soc Hd CapM8 x 1.25-30
I 24 I STD852005 * Lockwasher-Ext. 5

I 25 I 820240-3 Screw-Pan Cr M5 x 08-6

I 26 I 817697 Box-Switch
I 27 I 817698 Screw-Pan Cr M6 x 1.0-35

816!13 Switch-Locking

Key

No

29

30
31

32
33
34
35

36

37
38

39
4O

41
42

43
44
45

46
47
48
49

5O
5!
52

Pa_

No.

820248_2

9_22256
817699

817354
8!7698q
818511
820239

817308

STD8410!5
817667
813249-152

817685

817686

821738-3

822003-1
813249-53

822216-5
STD375008

820244
817321
813317-6

813317-7
813317-8
813317-9
SP5868

Description

Screw Self !ap Pan Hd

M4,2 x 1.4,-8

t Key-Switch

Cover-Switch Piate
Switch *Rocker
Screw.Pan Cr M6 x ! ,0,15
Lead-3"

Screw-Soc Hd Cap

M8 x 125-25

Screw-Special Set

Mt0 x 1.5-27

* Nut-Hex M!0 x t .5

Seat-Spring
Pin-Roll 6 x 16

Spring-Torsion
Cap-Spring
Nut-Hex M12 x 1.5-8
Cord-Power

Pin-Roll 2,5-10
Head w/Pointer & Trim

* Connector-Wire

ScrewoPan Cr M6 x t,0-t2
Socket-Bulb
Wrench-Hex "L'_M3
Wrench-Hex "L" M4

WrenchoHex "L" M5
Wrench-Hex "L" M6
Owners Manual

(Not I!lustrated)

•Any Attempt to Repair This Motor May Create a Hazard Unless Repair is Done by a Quaiified Service Technician,
Repair Service is Available at your nearest Sears Store.

* Standard Hardware Item..-May Be Purchased Locally,

t Stock Item-,-May Be Secured Through The Hardware Department Of Most Sears Retait Stores,

repair parts

PARTS LiST FOR CRAFTSMAN 20" DRILL PRESS

MODEL NO. 113.213213

19

I

13

14

12

15

l

2

7

FIGURE 2 - PARTS LIST

34

repair pa s

PARTS LIST FOR CRAFTSMAN 20" DRILL PRESS

MODEL NO, 113,213213

Always order by Part Number-Not by Key Number

FIGURE 2 - PARTS LIST

Key Part

No. No.

12817663

817391-1

3 822334
4 817712
5 817713
6 817662

7 817391
8 817661

9 STD837040

* Standard Hardware item - May be purchased locally

* Screw-Hex Hd

Description

Collar-Rack
Screw-Hex Soc Set

M6 x 1.0-10

Support-Table w/Indicator
Crank

Handle-Crank

Rack

Screw-Hex Soc Set

M_0x 1.5-12

Support-Column

M12 x 1.75-40

Key Part

No. No.

10 817709

11 819042

12 817720
13 STD840812

14 822069
15 817789

16 817288
17 817294
18 817350
19 817349

Description

Base
Tube-Column

Pin-Table Lock

* Nut-Hex M8x 1.25

Screw-Hex Hd M20 x 2.5-50
Table-Drill Press w/Scale

Pin-Gear
Clamp-Column

Gear-Hefical
Worm-Elevation

35

repair parts

PARTS LiST FOR CRAFTSMAN 20" DRILL PRESS

MODEL NO. 113.213213

11

12

12
..---3

6
7

Always order by Part Number-Not by Key Number

FIGURE 3 -PARTS LIST

I

Key i Part

No. No.

1 822057

2 817682
3 817681

4 STD315245

5 817684

6 817675

7 817326

* Standard Hardware Item -May be purchased locally

* Bearing-Ball20ram

Description

Lock-NutM20 x 1.5
Ring-Locking

Washer
Washer-Rubber

Tube-Quill

Key-Drift

:Key Pad

No. No.

8 823253
9 817340-5

10 824014

11 817676

12 STD315265
13 817679

tt - For alternate chuck and key with 1/32" - 5/8" capaci-
ty order part no. 817340 (chuck & key)

36

tt Chuck (Includes Key No. 8)

* Bearing-Ball 30mm

Description

Key-Chuck

Arbor

Spindle
Bearing-Thrust

repair parts

20

PARTS UST FOR CRAFTSMAN 20" DRILL PRESS

MODEL NO. 113.213213

7

\

9

Always order by Part Number-Not by Key Number

FIGURE 4 - PARTS LIST

Key Part

No.

1 STD304290
2 STD315225

3 817715
4 817716

5. 817717
6 817391-5
7 816755-3
8 63418
9 817451-1

10 817358-1

Standard Hardware Item - May be purchased locally

* Belt-"V" 1/2 x 29
* Bearing-Ball 15mm

Description

Pulley-Center
Pivot Idler

Pulley-Motor

Screw-Soc Set M8 x 1o25-12

Screw-Pan Hd M5 x 0.8-12

Clamp-Cord

Bushing-Rubber
Screw-Rd Wash Hd

M6 x 1.0-16

37

Key

No.

11
12

13

14

15
16

17
18
19

2O
21

L

Part

No.

STD852006
820294
822059
817668

STD315265
817670
817671
817705
822060

STD304330
817325

Description

iii

* Lockwasher Ext, M6

Washer Foam

Guard-Pulley w/Label
Ring-Retaining

* Bearing-Ball 30mrn

Spacer-Bearing

Insert-Pulley

Pulley-Spindle
Nut-Pulley

* Belt-"_r 1/2 x 33

Knob

Notes

38

39

MOTORIZED

20° NC

MODEL NO.

113.213213

DRILLPRESS WITH

MAXUMUM DEVELOPED

2 HP MOTOR

The model number of your
drill press isfound at the rear

of the head.
When requesting service or

ordering parts, always pro-
vide the following informa-
tion:

• Product Type

• Model Number

• Part Number
o Part Description

1

For the repair or replacement paAs you need

USTRIAL ATE

Call 7 am - 7 pro, 7 days a week

1-800°3G6-PART

(1-880-366q278)

For in-home major brand repair service

Call 24 hours a day, 7 days a week

1-800-4-REPAIR

(1-880-473-7247)

For the location of a

SearsRepair Service Center in your area

Call 24 hours a day,7 days a week

t -800-488-1222

DRILL

For information on purchasing a Sears

Maintenance Agreement or to inquire

about an existing Agreement

Call 9 am - 5 pm, Monday-Saturday

1-800-827-6655

SEARS

•:"'_, . *_

America's Repair Specialists

_. J J

Sold by SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60195 U.S.A.

Part No. SP5868 Form No, SP5868 Printed in China