Cradlepoint CTR350 User Manual
RegisterÊ yourÊ CTR350Ê
MobileÊ BroadbandÊ RouterÊ Today!
QUICK START GUIDE
CTR350
~ YOU WILL RECEIVE ~
FREE Technical Support
FREE Firmware Upgrades
New Product Information
Special Offers & Promotions
Also, get a FREE Car Charger!
cradlepoint.com/register
What’s Included In The Box
•
3G Mobile Broadband Travel Router
•
AC Power Adapter
Wireless Setup using a Mobile Broadband
*
(cellular) Data Modem
Connect Power Supply and insert a USB modem or compatible Phone via USB.
Then establish a wireless internet connection as shown below.
or Compatible Phone
•
Quick Start Guide
3G Mobile
Broadband
Travel
Router
Wired Connection using Cable/DSL Internet Service
Connect power and insert one end of your Ethernet cable (not included) to the WAN port. Insert the
other end of
two for the
the Ethernet cable into your Internet service provider's modem. It may take a minute or
CTR350 to initialize. Open your web browser. You can now access the Internet.
Note: CradlePoint recommends that WiFi security be setup at this point.
See the “Setting WiFi security on your CradlePoint Router” section of this guide.
USB Modem
or
Phone
via
USB
* Mobile Broadband Data Modem not included.
See your Mobile Broadband Service Provider for details.
Power
Supply
Establishing a Wireless Internet Connection
1) Find Your
Windows XP
Open your computer’s WIRELESS NETWORK
CONNECTION to
Access Point. This is typically completed by opening
VIEW AVAILABLE NETWORKS window. After you
have highlighted the CTR-xxx, click CONNECT.
CTR350
associate with the router’s Wireless
Windows Vista
Open CONNECT TO A NETWORK by clicking
the Start button, and then click CONNECT TO.
You'll see a list of the wireless networks
currently available. Click on the CTR-xxx
network, and then click CONNECT.
Ethernet
Cable
Modem
Mac
Open your wireless connection list by
clicking the AIRPORT wireless icon
on your menu bar. Click the CTR-xxx.
Power
Supply
Internet
Service (ISP)
CTR350
CTR350
2) Connect To the Internet
1) Using either a Windows or Mac platform, open a browser window.
A default CradlePoint page will appear asking for a password.
2) The password is the last six digits of the MAC address shown on the box label
and on the bottom of the router. This is a unique number identifying your router.
3) Once you have correctly entered your password, click “OK”.
You can now access the Internet.
Note: CradlePoint recommends
that WiFi security be setup at
this point. See the “Setting WiFi
Security on your CradlePoint
Router” section of this guide
Port Diagram
LEFT SIDE
USB
AIR VENTS
POWER
LEDs
WLAN
CTR350
USB
WAN
RIGHT SIDE
RESET
WAN
POWER
TECHNICAL INFORMATION FOR THE CTR350
Setting WiFi Security on your CradlePoint Router
WiFi security is highly recommended by CradlePoint. WiFi Security is separate from the
User Login Page. Setting “WiFi Security” on your router prevents users from connecting their
computers to your router unless they have your wireless security password.
Follow The Steps Below To Set The WiFi Security:
1) Access your router administration page by opening your browser and typing
http://192.168.0.1 in the address bar.
6) Configure security by selecting either ENABLE ADVANCED SECURITY CONFIGURATION
or REQUIRE USER LOG-IN.
7) When you select ENABLE ADVANCED SECURITY CONFIGURATION, you can rename
your wireless network and select your security mode: GOOD for WEP, BETTER for WPA
and BEST or WPA2. (Make sure your PC or other devices support the mode you choose.)
Enter a personalized SECURITY PASSWORD.
2) Click on the BASIC tab, click WIZARD, click NEXT.
3) You will see a summary of the upcoming Wizard Steps, click NEXT.
4) Enter your default Administrative password. This password is the last six digits of
the MAC address found on the label on the bottom of the router. Also select your
TIME ZONE, click NEXT.
5) Select your CONNECTION TYPE (USB Modem or Ethernet), click NEXT.
Your USB Modem or Phone Does Not Work With the Router
1) If your USB data modem or phone is not working with the router, check the list of supported
devices to ensure you are using a supported device and carrier. The device you’re using
must be supported on the carrier network providing your cellular service or it’s considered
an unsupported device, even if it is supported on another carrier’s network.
CradlePoint’s supported device list changes regularly. We update our supported device list
after a device is certified and approved. If the device you have is NOT on the list, that means
we do not support it at this time.
The SUPPORTED DEVICE list can be found at: cradlepoint.com/support/ctr350
2) Sometimes a USB data modem needs to be updated or have other configurations set correctly
in order to make a connection through the router. If your USB Modem has not been updated
recently, it is recommended that you do so if it is having trouble connecting to the CTR350.
Simply insert your USB data modem into your PC and using the software provided by your
cellular carrier, access the Internet. Follow the directions provided to complete the update.
Once you have updated your USB data modem, reconnect the cellular device to your
CradlePoint router and connect to the Internet.
8) Only select REQUIRE USER LOG-IN if you wish to force every user of the router to log-in
using the User Login Password (Set in a separate location in the User Interface), click NEXT.
9) Record the setup information shown on the final summary page, then click CONNECT.
This will save your new settings and reboot your router to operate based on your new
security information.
You’ve now secured your CradlePoint router from unintended WiFi access.
You are Connected to the Router but Cannot Connect to the Internet
The status LEDs of your router will give you an indication whether or not a proper connection is
being made. See the LED STATUS definitions below:
POWER
WLAN
The CTR350 must be powered using an approved power adapter.
Green
The CTR350 is powered on.
No Light
When your CTR350 is up and running, it creates a shareable wireless signal (WLAN).
Green
No Light
WAN
You may connect the CTR350 via an Ethernet cable to your WAN (Wide Area Network) Internet Modem.
Green
No Light
USB
The CTR350 works with a Mobile Broadband Data Modem or tethering phone with a data plan via the USB port.
Green
No Light
The CTR350 is not connected to power.
The Wireless LAN is active and available to share.
The Wireless LAN is not active.
Connected to an active Ethernet Connection.
Not connected to Ethernet or the connection is not configured correctly.
Data connection has been established with your cellular network.
Cellular network is unavailable or connection is still in progress.
Standard connection time is 15-30 seconds.
If, after following the above directions, you are still unable to access the Internet,
contact CradlePoint Technical Support for further assistance.
My WiFi-enabled Devices Can’t Get Past The Login Page
Some electronic devices may experience problems handling the Internet Access User Login setting.
Devices that commonly have trouble are, but not limited to:
• iPod Touch
• iPhone
• Wireless VoIP Phones
To Allow These Devices Access, follow the instructions below to disable the user login.
1) Access your router administration page by opening your browser and typing
http://192.168.0.1 in the address bar.
2) Go to the TOOLS tab on the top navigation, then the USER LOGIN menu on the left panel.
3) Uncheck the REQUIRE USER LOGIN check box.
4) Scroll to the top of the page and click SAVE THE SETTINGS, which will save and reboot the
router with your new configuration.
Note: Because the User Login page adds security and access control to others connected to your router,
you may need to enable additional security features such as WEP, WPA, or MAC Address Filtering (if you
are not already doing so) when turning off the User Login Page. See the “Setting WiFi Security on your
CradlePoint Router” section of this guide for details.
• Wireless Printers
• most WiFi-enabled Video Game Systems
• most WiFi-enabled Devices that are not PCs or Macs
If the USB Data Modem LED is not illuminated, your modem is not connected and online. You may
need to update firmware. Refer to “Your USB Modem or Phone Does Not Work With The Router.”
If, after updating, you are still not online, call CradlePoint Technical Support for further assistance.
I Need To Update My Firmware
To support the latest features, modems, and phones, follow the directions below:
1) Access your router administration page by opening your browser and typing
http://192.168.0.1 in the address bar.
2) Select the TOOLS tab on the top navigation, then the FIRMWARE menu on the left.
3) Select One-Button Firmware Update for easy firmware updates.
If you experience problems, you can also install the firmware manually.
1) Download the new firmware by going to cradlepoint.com/support/ctr350.
2) Select the TOOLS tab on the top navigation, then the FIRMWARE menu on the left.
3) In the FIRMWARE UPGRADE section, click BROWSE.
4) Browse for the new firmware file you downloaded in Step 1 and click OPEN.
5) Click the UPLOAD button. The upgrade process can take a minute or two.
DO NOT TURN OFF OR UNPLUG THE DEVICE WHILE IT IS UPGRADING!
StillÊ HaveÊ Questions??
visit
cradlepoint.com/knowledge-base
or
EMAIL support@cradlepoint.com
CHAT cradlepoint.com/content/chat-support
CALL (208) 424-5054 Option #2
Monday-Friday 7:00am to 7:00pm MST
Regulatory Information
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. This device must accept any interference received, including
interference that may cause undesired operation. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for help.
Changes or modifications not expressly approved by CradlePoint, Inc. could void the user’s authority to operate the product.
Radio Frequency Interference Requirement - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Warranty Information
CradlePoint, Inc. warrants this product against defects in materials and workmanship to the original purchases (or the first
purchaser in the case of resale by an authorized distributor) for a period of one (1) year from the date of shipment. This warranty
is limited to a repair or replacement of the product, at CradlePoint’s discretion.
Within thirty (30) days of receipt should the product fail for any reason other than damage due to customer negligence, purchaser
may return the product to the point of purchase for a full refund of the purchase price.
If the purchaser wishes to upgrade or convert to another CradlePoint, Inc. product within the thirty (30) day period, purchaser
may return the product and apply the full purchase price toward the purchase of the other product. Any other return will be
subject to CradlePoint, Inc.’s existing return policy.
Loading...