Code 3 Ultra-Lite Strobe Beacon User Manual

®®

®

ULTRA-LITEULTRA-LITE

ULTRA-LITE

ULTRA-LITEULTRA-LITE
MODEL L1000HMODEL L1000H

MODEL L1000H

MODEL L1000HMODEL L1000H

INSTALLATION INSTRUCTIONS - DC Models OnlyINSTALLATION INSTRUCTIONS - DC Models Only

INSTALLATION INSTRUCTIONS - DC Models Only

INSTALLATION INSTRUCTIONS - DC Models OnlyINSTALLATION INSTRUCTIONS - DC Models Only

ULTRA-LITE: Use on 12-48VDC only. Average load current approximately 1A@ 12 vdc.
FIRE-FLASH: Use on 12-24VDC only. Average load current approximately 1.5A@12 vdc.

Red wire is Positive (+)
Black wire is Negative (-)

Use fuse loop included for protection. Locate as close to the battery as possible. Failure to
use fuse loop voids warranty. To install fuse loop, cut loop in two and remove one-half inch
insulation from each end. Connect one end to Positive, the other end to the red lead of the

strobe light. Connect black lead to vehicle ground.

®®

REPLACEMENT PARTS LIST

PART NO. DESCRIPTION

15597 XENON FLASH TUBE
14425 LENS O-RING
13069 LENS RETAINER RING
14428 ALUMINUM CIRCUIT CASE
14533 BASE MOUNTING GASKET
13075 LENS DUST COVER
14429 BRANCH GUARD FOR 4” LENS
14630 BRANCH GUARD FOR 6” LENS
13057 6” AMBER LENS
13058 6” BLUE LENS
13059 6” CLEAR LENS
13060 6” GREEN LENS
13061 6” MAGENTA LENS
13062 6” RED LENS
13063 4” AMBER LENS
13064 4” BLUE LENS
13065 4” CLEAR LENS
13066 4” GREEN LENS

FIRE-FLASH II FIRE-FLASH II

FIRE-FLASH II

FIRE-FLASH II FIRE-FLASH II

MODEL L9200H MODEL L9200H

MODEL L9200H

MODEL L9200H MODEL L9200H

13067 4” RED LENS

Public Safety Equipment, Inc. emergency devices are tested and found to be operational
at the time of manufacture. Provided they are installed and operated in accordance with
manufacturer’s recommendations, PSE. guarantees all parts and components except the
lamps to a period of 2 year (unless otherwise expressed) from the date of purchase or delivery,
whichever is later. Units demonstrated to be defective within the warranty period will be
repaired or replaced at the factory service center at no cost.

Use of lamp or other electrical load of a wattage higher than installed or recommended
by the factory, or use of inappropriate or inadequate wiring or circuit protection causes this
warranty to become void. Failure or destruction of the product resulting from abuse or unusual
use and/or accidents is not covered by this warranty. Code 3, Inc. shall in no way be liable for
other damages including consequential, indirect or special damages whether loss is due to
negligence or breach of warranty.

PUBLIC SAFETY EQUIPMENT, INC. MAKES NO OTHER EXPRESS OR IMPLIED
WARRANTY INCLUDING, WITHOUT LIMITATION, WARRANTIES OF FITNESS OR
MERCHANTABILITY, WITH RESPECT TO THIS PRODUCT.

PRODUCT RETURNS

If a product must be returned for repair or replacement*, please contact our factory to obtain
a Return Goods Authorization Number (RGA number) before you ship the product to
Public Safety Equipment, Inc. Write the RGA number clearly on the package near the
mailing label. Be sure you use sufficient packing materials to avoid damage to the product
being returned while in transit.

*Public Safety Equipment, Inc. reserves the right to repair or replace at its discretion. Public Safety Equipment, Inc. assumes no
responsibility or liability for expenses incurred for the removal or reinstallation of products requiring service or repair; nor for the packaging,
handling, and shipping: nor for the handling of products return to sender after the service has been rendered.

WARRANTY

NEED HELP? CALL OUR TECHNICAL ASSISTANCE HOTLINE [phone]

Public Safety Equipment, Inc.

10986 N. Warson Road

www.code3pse.com

Ultra-Lite and PSE-AMBER are registered trademarks of Public Safety Equipment, Inc.

St. Louis, Missouri 63114-2029—USA

Revision 3, 12/2005 - Instruction Book Part No. T15067
©2004-5 Public Safety Equipment, Inc. Printed in USA