Code 3 M180L Series, M180LMC Series, M180L-B, M180L-A, M180LMC-BA Installation And Operating Instructions Manual
...
Installation and Operation Instructions
Installation and Operation Instructions
M180SL& M180LMC directional LEDs are bright and versatile 180
degree warning light and work light that are suited to a wide variety
of applications. Their triple stack design offers approximately 3
times the light output of the popular M180S series. Their
low prole design coupled with multiple mounting options
(surface, edge, self-adhesive and permanent) and 30
degrees of adjustable pivoting, provide superior exibiltiy
when positioning the lights for optimum warning capability.
Both models offer multiple ash patterns and multiple units
can be synchronized to operate either simultaneously or
alternately with each other.
Available in solid colors: M180L-X (A,B,R,W)
dual colors: M180LMC-XX (BA, RA, AW, BW, RW, RB)
WARNING!
Failure to install or use this product according to manufacturers recommendations may result in property
damage, serious injury, and/or death to those you are seeking to protect!
M180L/M180LMC
WARNING LIGHT
Do not install and/or operate this safety product unless you have read and understand the safety information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are
essential to ensure the safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he
can operate the system without losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air
bag deployment area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal
injury or death. Refer to the vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/
operator to determine a suitable mounting location ensuring the safety of all passengers inside the vehicle particularly
avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use,
the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open
trunks or compartment doors), people, vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an inter-
section, driving against trafc, responding at a high rate of speed, or walking on or around trafc lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying
all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and
regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.
Distributed By:
920-0661-00 Rev. C Page 1 of 8
CONTENTS:
1 Light Head
1 Multi-Mount Base:
Includes:
2- M4x25 Sheet metal screws
1 1-EVA foam gasket
1 1-BEZEL
SPECIFICATIONS:
Input Voltage 12-24VDC
Work Current M180L = 1.7A Max @ DC12V
M180LMC = 1.7A Max @ DC12V
Important! This unit is a safety device and it must be
connected to its own separate, fused power source to assure its
continued operation should any other electrical accessory fail.
Caution: When drilling into any vehicle surface, make sure the
area is free from any electrical wires, fuel lines, vehicle upholstery,
etc. that could be damaged
Wire: M180LS
RED: Positive(need to add 2A Fuse)
BLACK: Negative
BLUE: Pattern Select to Negative and Dimming to Positive
YELLOW: Synchronized Function
(Up to 8 units can be Synchronized)
ORANGE: Takedown Light Operation
Operation Environment:
Ambient Temperature:
-30 to 50°C
Wire: M180LMC
RED: Positive, Colors 1 & 3 (need to add 5A Fuse)
WHITE: Positive, Colors 2 & 4 (need to add 5A Fuse)
BLACK: Negative
BLUE: Pattern Select to Negative and Dimming to Positive
YELLOW: Synchronized Function
(Up to 8 units can be Synchronized)
ORANGE: Takedown Light Operation
PRODUCT 1 & 3 COLORS 2 & 4 COLORS
M180LMC-AW AMBER WHITE
M180LMC-BW BLUE WHITE
M180LMC-RB RED BLUE
M180LMC-RW RED WHITE
M180LMC-BA AMBER BLUE
M180LMC-RA AMBER RED
RED WHITE
Pattern Select Operation:
The light ash pattern may be changed by holding the blue wire to ground for the following intervals:
1 second: increment ash pattern
3 seconds: decrement ash pattern
5 seconds: reset to default
7 seconds: set to last ash pattern
Note: The blue wire must be disconnected from any voltage when operating except when changing ash patterns or
activating dim.
920-0661-00 Rev. C Page 2 of 8
M180L Series Flash Pattern Chart:
13
12
10
11
9
29
28
26
27
Modulation NO N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
Steady Burn NO N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
25
Steady - Single NO N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
4 Single Flash ,2 Quad Flash Alt. NO N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
2 Double Flash,2 Triple Alt. NO N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
24
Quint Flash 150FPM Alt. yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
23
8
Quint Flash 150FPM sim. Phase2 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 120 100 100 60 N/C N/C N/C
22
Quint Flash 150FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 120 100 100 60 N/C N/C N/C
21
TripleAlter 75FPM Alt. yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
20
7
Triple 75FPM sim. Phase2 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 140 140 140 140 N/C N/C N/C
19
Triple 75FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 140 140 140 140 N/C N/C N/C
18
Quad Flash 150FPM Alt yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
17
6
Quad Flash 150FPM sim. Phase2 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 120 100 100 60 N/C N/C N/C
16
Quad Flash 150FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 120 100 100 60 N/C N/C N/C
15
Quad Flash 75FPM Alt. yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
5
14
Quad Flash 75FPM sim. Phase2 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 140 120 100 80 N/C N/C N/C
13-Default
12
Double Flash 120FPM Alt. yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
Quad Flash 75FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 140 120 100 80 N/C N/C N/C
4
11
Double Flash 120FPM sim. phase2 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 140 140 120 120 Class 2 Class 2 Class 2
10
Double Flash 120FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 140 140 120 120 Class 2 Class 2 Class 2
9
Double Flash 75FPM Alt. yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
8
3
Double Flash 75FPM sim. phase2 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 160 140 140 140 N/C N/C N/C
7
Double Flash 75FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 160 140 140 140 N/C N/C N/C
6
Single Flash 120FPM Alt. yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
5
2
Single Flash 120FPM sim. phase2 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 160 140 140 140 N/C N/C N/C
4
Single Flash 120FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C 160 140 140 140 N/C N/C N/C
3
Single Flash 75FPM Alt. yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C
2
1
Single Flash 75FPM sim. Phase2 yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B 160 140 140 140 N/C N/C N/C
Pattern MODE PATTERNS SYNC.
1
Single Flash 75FPM sim. Phase1 yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B 160 140 140 140 N/C N/C N/C
RED AMBER BLUE WHITE RED AMBER BLUE RED AMBER BLUE WHITE RED AMBER BLUE
SAE J595 CA T13 SAE J845 ECE R65
920-0661-00 Rev. C Page 3 of 8
Loading...