FRANÇAIS ESPAÑOL ENGLISH
CSC 600
V508
1 – ENGLISH
Congratulations on your purchase of the CSC600 Phone from ClearSounds Communications®. Please read this User Guide carefully in order to get the very best results from your telephone. Keep the manual near the telephone for easy reference.
Please visit our web site at www.clearsounds.com to: Register your product, download additional manuals, and review trouble shooting tips.
Due to the nature of VOIP/Broadband technology results may vary when used with VOIP/Broadband service
IMPORTANT SAFETY INSTRUCTIONS
Read and understand the Installation Guide & User Manual. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following.
WARNING: The CSC600 Phone is capable of amplifying sounds to a loud volume. It is important to instruct all potential users of its proper operation. It is advised to adjust the volume control to the minimum level (Low) when not in use and alert other users that hearing damage can potentially result from misuse.
WARNING: To avoid the possibility of electrical shock, do not use this product near water (For example, near a bathtub, wash basin, kitchen sink or laundry tub, in a wet basement or near a swimming pool) while in the bathtub or shower or when you are wet. If the phone becomes submerged in water, do not attempt to retrieve it until after you have unplugged the AC adapter from the electrical outlet and the line cord from the modular wall jack. Do not plug the phone back in until it has dried completely.
WARNING: Avoid using the telephone during electrical storms. There may be a remote risk of electric shock from lightning. If the electrical storm is present in your immediate area, possibility of electrical shock exists.
WARNING: Do not use the phone if you suspect a gas leak in the area. The phone’s electrical contacts could create a spark, which could ignite any heavy concentration of leaking gas.
WARNING: Do not use liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth for cleaning.
2 – ENGLISH
WARNING: No telephone should ever be placed near an open radiator or heating register.
WARNING: Occasionally a power surge can occur on electrical lines without warning. With any electrical device that you plug into an outlet, it is suggested you use a surge protector. A surge protector will prevent power surges from damaging your telephone. Surge protectors are simple devices available at your local hardware store.
WARNING: Never push any objects through the slots in the phone. They can touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock.
WARNING: Do not cover slots and openings on the unit, they are needed for ventilation and protection against overheating. Never place the unit near hot places where proper ventilation is not provided.
WARNING: Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:
A When the power supply cord or plug is damaged B If liquid has been spilled over the unit
C If the unit has been exposed to rain or water
DIf the unit does not work normally upon following the instructions. Adjust only controls covered by the operating instructions, to avoid expensive repairs by qualified technicians.
E If the unit has been dropped or damaged
F If the unit exhibits a distinct change in performance
3 – ENGLISH
PLEASE SAVE THESE INSTRUCTIONS
|
VOL |
HI |
|
|
SPCHLO |
|
1 Hook switch
2 Caller ID Screen
3 Delete Button
4 Up and Down Buttons
5 Dial Button
6 Phonebook Button
7 Handset Tone control
8 Handset Volume control
9 Voice mail button
10 Call waiting
11 Programming button
12 Emergency Memory Dial
13 Amplify Button
14 Headset Button
15 Speaker Button
16 Flashing incoming call indicator
17 Redial Button
18 M1-M5 One Touch Memory Dial buttons
19 Speakerphone
20 Speaker Volume Control
21 Ringer Volume
22Outgoing speech volume select switch (LO/NORMAL/HI)
23Audio Neckloop jack
24Optional Bed Shaker Jack
25Ringer, Strobe, Shaker, Selector
26Auto Amplify/Volume reset override
27AC Power Adapter Jack
28Phone line jack
29Handset cord jack
30Headset jack
31Battery Compartment
32Dialing Mode Switch (Tone/ Pulse)
33Message Waiting Indicator/ Off/On switch
4 – ENGLISH
Installation of your ClearSounds® CSC600 Amplified Phone is easy. There are some basic steps you need to take when you set-up your CSC600 Phone for the first time.
1Check parts list.
a Handset with handset cord and phone base b Telephone line cord
c User’s Manual
d AC Power Adapter
2 Install (4) AAA Alkaline batteries (optional). This provides back-up power to the Caller ID Screen.
3 Phone mounting installations.
4 Set the dialing mode.
5 Choose desktop or wall mount.
6 Set ringer and auxiliary alert.
7 Program your memory dial buttons.
INSTALLING THE OPTIONAL BATTERIES
The batteries are necessary in case of network power failure to save stored numbers in memory and in the phone book.
1Begin by unplugging the AC adapter & line cord before installing new batteries.
2Open the battery compartment door located on the bottom of your phone by unscrewing the battery compartment door and removing it from the bottom of your phone (screwdriver provided).
3Correctly insert 4 AAA alkaline batteries (purchased separately) in the battery compartment. Be sure to observe battery polarity as imprinted on the base of the compartment.
4 Replace the battery compartment door and screw back in place.
BATTERY SAFETY
1When replacing the batteries in your CSC600 phone, make sure to put the batteries in correctly.
2 Never mix battery types (different chemistries, brands and/or fresh vs. used). 3 Never dispose of batteries in fire, as they could explode.
4Remove worn-out batteries from equipment immediately and dispose of promptly.
5Do not attempt to recharge a battery unless the battery specifically is marked “rechargeable.”
5 – ENGLISH
NOTE: Disposing of used batteries improperly may cause environmental damage.
PHONE MOUNTING INSTALLATIONS
The telephone may be placed on a shelf or table, or may be fixed to a wall using the mounting bracket.
Plug the AC Adapter into the AC power back on the back of your phone, then into an electrical outlet or surge protector, if you are using one.
NOTE: The adapter is required for the telephone to work correctly. If the adapter is accidentally unplugged (or in case of power failure) the amplification feature will not work properly. If the batteries are dead or not installed, some of the phone features will not work.
IMPORTANT: Please remove the clear plastic Caller ID tab. This film tab is only for display and to protect your Caller ID display during shipping.
Desk / Table Use
1Connect one end of the 6ft telephone cord to the line jack on the back of your CSC600 Phone and connect the other end to a modular phone jack (RJ11C).
2Connect the handset coil cord (curly cord) to the handset and to the telephone.
3Lift the handset and listen for a dial tone. If you hear a dial tone, your phone is ready to use. If there is no dial tone, check all your cords to make sure they are plugged in securely.
Wall Mount Use
1Slide the handset hanger tab out and reverse its position (rotate it 180 degrees). Slide it back into place so that the hook points up. This will keep the handset from falling out of the cradle when it is mounted on the wall.
2Plug the 8in short phone cord into the telephone jack on the CSC600, run phone cord underneath wall plate adapter and through the opening.
3Insert the Wall Plate adapter. Hold the wall plate adapter so that the raised mounting pins line up with the phone’s keyholes on the CSC600. Once the holes are lined up, push the wall plate adapter in towards the CSC600 and then slide the plate upwards until it is securely seated on the phone.
4With the Wall Plate adapter installed, plug the 8 inch short cord into the jack on the wall.
5Holding the phone slightly above the mounting screws on the wall jack, push the phone against the mounting screws so they are hooked into
6 – ENGLISH
upper and lower key hole slots on the back of the phone. Slowly slide the phone down until it snaps into place.
6Connect the handset coil cord (curly cord) to the handset and to the telephone.
7Attach the AC Power Adapter to the back of the phone and plug the other end into a working electrical outlet (not controlled by a wall switch).
8Lift the handset and listen for a dial tone. If you hear a dial tone, your phone is ready to use. If there is no dial tone, check all your cords to make sure they are plugged in securely.
SETTING UP PHONE
BASIC FUNCTIONS
Setting The Dialing Mode
Set the dial mode switch on the bottom of the phone to “T” if you have Touch Tone service, or “P” for Pulse dialing if you have rotary dialing service. The default is set to the “T” dialing switch mode.
Redial Function
This feature allows you to redial the last number you have called by one-touch operation.
1 Lift the handset or press the SPEAKER button to get a dial tone. 2 Press the REDIAL button to redial the last number called.
Flash Function
Press the CALL WAITING button to end a call and get a dial tone for another call or to switch to another call from “call waiting”.
NOTE: You must subscribe to Call Waiting Service from your local phone company. If you do not subscribe to Call Waiting, pressing the CALL WAITING button during a call may disconnect your current call.
Speakerphone
Making A Call Using The Speakerphone
1 Press the SPEAKER button for dial tone.
2 Adjust the volume to fit your needs. Move the Speaker Volume Adjustment Switch located to the side of the telephone.
3To dial a number you can:
a Dial a number from the keypad
b Press one of the Priority or Memory dial buttons c Dial from your Phone Book or Caller ID
7 – ENGLISH
Loading...