Clarke COB 10C, 4003600 User guide

10W LED WORKLIGHT(110V)

MODEL NO: COB10C/110

PART NO: 4003600

ASSEMBLY & USER

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1119 ISS 2

INTRODUCTION

Thank you for purchasing this CLARKE portable worklight. This portable
worklight with carrying handle/ floor stand is suitable for indoor or outdoor use.

Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.

2

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SAFETY PRECAUTIONS

1. This worklight must not be immersed in water.

2. Do not look directly into the lamp when switched on as this can damage
the eyes.

3. If used with an extension cable always ensure that the extension cable is
fully unwound.

4. Do not use this worklight if it has a broken lens, casing or damaged supply
cable

5. Always unplug the worklight before moving it or performing maintenance.
Do not touch the lamp when your hands are wet.

6. Do not attempt to disassemble or repair the worklight.

7. Do not leave the worklight unattended when switched on. Always unplug
the worklight when it is not in use.

8. Never unplug the worklight by holding the cable. Unplug by holding the
plug.

9. Never use the worklight if the cable or plug are damaged.

3

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

ELECTRICAL CONNECTIONS

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO A
POWER SUPPLY.

This product can be connected to one of the following power supplies:

• 110V generator

• 110V isolating transformer

• 110V site supply

• 230V generator via a 110V transformer.

Connecting it to any other power source may cause damage.

This product includes a fitted industrial plug to BS-EN
60309, and a cable for use with a 110 volt supply. On
no account must a 230V, 13amp (BS1363) plug be
used.

If using a portable 110V transformer make sure it has a
rated capacity sufficient to take the load of the
worklight.

Should the plug need changing at any time, ensure
that a plug of identical specification is used and
proceed as follows:

1. Undo the socket screws & remove the rear section.

2. Rotate the cable clamp clear of the terminals.

3. Feed the cable through the rear gland in the plug.

4. Remove the cable sheath to the required lengths
as shown in the diagram.

5. Terminate the correct wires in the
correct terminal blocks as shown.

6. Remove the cable clamp screws. Clip
the cable clamp back into position and
place the clamp around the outer
sheath of the cable. Replace the screws
and tighten until the cable is securely
held.

7. Replace the rear cover and tighten the cover screws.

4

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.

The user should purchase a suitable connecting lead which is compatible with
the worklight socket. The length giving mobility to the worklight but without
becoming a trip hazard.

ASSEMBLY & MOUNTING

The worklight is mounted on a carry
frame which is assembled as follows:

1. Remove the locking knob from
the base of the carry frame, then
insert the tubular base into the
frame attachment, as shown.

2. Line up the holes in the two
sections of the frame then
replace and tighten the fixing
screw.

CARE & STORAGE

1. When not in use, switch off & unplug from the power supply.

2. Store this worklight in a secure, dry place, out of the reach of children. DO
NOT leave it exposed to the elements and avoid direct sunlight, direct
heat, rain/moisture etc.

3. Keep the external surfaces clean. Avoid impact damage & do not allow
this worklight to come into contact with abrasive or corrosive materials.

4. Do not use solvents, thinners or alcohol for cleaning, as these chemicals will
damage the finish. With the worklight unplugged from the power supply,
use a dry cloth to wipe over the components.

5. Only use extension leads that are of an appropriate power rating and
suitable for the work environment. Inspect the extension lead regularly and
replace if damaged.

6. The LED light source cannot be replaced but has a life expectancy of
approximately 20,000 hours.

5

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

7. Only use parts and accessories recommended in this manual. Never use
unauthorised accessories or attachments which may result in personal
injury or damage to the product.

8. Do not attempt to repair or modify this product or attempt any electrical
repair yourself. Consult the Clarke Service Department on 020 8988 7400.

ERP TECHNICAL INFORMATION

Model COB10C/110

Part No 4003600

Model type L9601P

Dimensions (L x W x H) 180 x 156 x 250 mm

Weight 1.1 kg

Operating Temperature

-20oC to +50oC

Input power (consumption) 10W

Light Source COB LED

Light Output (luminous flux) 800 lumen @ 1m

Efficiency 80 Lm/W

Power Supply 110V 60HZ

Insulation Class I

IP Rating IP65

Energy Efficiency Class A+

Colour Temperature 6500 K

Weighted Energy Consumption 10 kWh/1000h

Life expectancy of LED 20,000 hours

Tilt Adjustment

-90

o

to +90

o

6

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

DECLARATION OF CONFORMITY

7

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]