Clarion WH200 User Manual

WH200

OWNER’S MANUAL
INSTALLATION GUIDE

D

UALCHANNEL

S

TEREO

I

NFRARED

H

EADPHONES

1

W

ARNING

!

THE CLARION WH200 DUAL INFRARED HEADPHONES ARE
DESIGNED FOR LISTENING TO VIDEO OR AUDIO SOURCES
FOR REAR SEAT PASSENGERS ONLY.

THIS PRODUCT IS NOT INTENDED FOR USE BY THE DRIVER
WHILE THE VEHICLE IS IN MOTION SINCE SUCH USE MAY
DISTRACT THE DRIVER OR INTERFERE WITH THE DRIVER’S
SAFE OPERATION OF THE VEHICLE AND MAY RESULT IN
SERIOUS INJURY OR DEATH. SUCH USE MAY ALSO VIOLATE
STATE LAW.

CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY
INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE
THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED
USES OF THIS PRODUCT.

A

BOUTINSTALLATION

Installation of mobile audio and video components requires
experience with a variety of mechanical and electrical proce­dures. Even though this manual provides general installation
and operation instructions for your new Clarion WH200 Dual
Channel Infrared Headphones, it does not show the exact
installation methods for your particular vehicle.

If you do not have the required knowledge and experience to
successfully complete the installation, we strongly recom­mend consulting an authorized Clarion Pro Audio dealer
about professional installation options.

T

ABLEOFCONTENTS

Introduction...............................................................2

Description Of Controls and Indicators.......................3

IR Transmitter Specifications ......................................3

Description of Headphone Controls............................4

Battery Installation....................................................5

Operation Description................................................5

Operation Precautions...............................................6

Installation Precautions .............................................6

Mounting Description.................................................7

Wiring Description.....................................................8

Troubleshooting ........................................................9

FCC Statement ...........................................................9

OWNER’S MANUAL/INSTALLATION GUIDE

2

I

NTRODUCTION

The Clarion WH200 is a full-featured Dual Channel Infrared
Headphone System specifically created for the mobile envi­ronment. The WH200 frees you from the tangle of head­phone wires and lets you enjoy music or TV audio without
the clutter of cables. To ensure the best performance of your
system, please read this manual carefully .

When used with the enclosed pair of individual headphones,
the system allows independent source selection of two audio
channels (ex: audio or video sources), each capable of play­ing a different high-fidelity stereo program. Each headphone
allows for independent volume and source selection to pro­vide individual and private listening.

Special Features

• Automatic Level Control prevents input signal over load­ing.

• Uses high frequency infrared light to assure a clean signal
for clear reception.

• Power Indicator LED.

• Two Channel Input Operation.

• Auto ON/OFF Micro Switch.

• Independent Volume Controls.

• Independent A/B Channel Selection Switches.

About The Manual And Warranty

To start enjoying your new Clarion WH200 system, please
read all remaining instructions listed in this manual. Keep all
instructions for future reference.

This product is covered by a limited warranty (see the
enclosed warranty card). Save the sales receipt to protect

your purchase and aid in warranty service.

WH200

DUAL CHANNEL INFRARED HEADPHONES

Additional Headphones

The Clarion WH200 allows users to take full advantage of the
benefits of infrared audio transmission and its ability to oper­ate multiple headphones from one single transmitter. There is
no need for Y-adapters, complex installation, or concerns
over electrical overload. Additional headphones,WH200H,
are available through your local Clarion Audio Dealer.

3

Infrared Transmitter

1

IR Array window

Point Infrared LED array window toward users.

2

Mounting hole locations (covers removed)
Use M4x12 sheet metal screws to attach IR Transmitter.
(see Mounting Description on page 7).

D

ESCRIPTIONOFCONTROLS ANDINDICATORS

Figure 1. The WH200 Transmitter descriptions.

OWNER’S MANUAL/INSTALLATION GUIDE

IR T

RANSMITTERSPECIFICATIONS

General Specifications

Power Requirement: 12 volts dc
Power Consumption: 1 watt, Power On
Dimensions (w x h x d): 3.75 x 1.89 x 4.72 in.

Mounting Base (95 x 48 x 120 mm)
Mounting Holes: 3.86 in.

(to centers) (98 mm)
Supplied Accessories: (2) M4x12 Sheet Metal Screws,

(1) 5-pin Power/Channel A Molex,
(1) 3-pin Channel B Molex
(2) Plastic Screw cover inserts.

4

Figure 2. The WH200 IR Remote Headphone controls and indi­cators.

D

ESCRIPTIONOFHEADPHONECONTROLS

Infrared Headphones

3

POWER Switch
Main power switch turns headphone power off to prevent
accidental micro switch activation during storage.

4

POWER Indicator

When illuminated the headphones are fully functional.
The indicator will turn off when the headphones are
removed or when the power switch is turned off.

5

CHANNEL SELECTION A/B Switch
Allows user to choose the audio source.

6

VOLUME Control
Allows user to set individual listening levels.

7

BATTERY Compartment
Remove the cover and place 2 Alkaline AAA batteries in
the compartment. (See page 5 for information).

8

MICRO Switch
Turns the headphones ON when placed on the user’s head
and turns OFF the headphones when removed.

WH200

DUAL CHANNEL INFRARED HEADPHONES

5

B

ATTERYINSTALLATION

1. Open the battery compartment by sliding the cover
toward the bottom of the Headphone.

2. Place two (2) alkaline AAA batteries into the battery
compartment of the Headphones, making sure that the
battery polarity is correct.

3. Snap the battery cover back into place.

O

PERATIONDESCRIPTION

PLEASE READ CAREFULLY TO PREVENT DAMAGE TO THE
HEADPHONES OR YOUR EARS.

1. Be sure batteries are properly installed in the
Headphones.

2. Turn the Headphone volume nearly off before turing on
the power switch.

3. Turn the Headphone power switch to the ON position.

4. Place the headphones on your head and the power indica­tor will illuminate.

5. Adjust the Headphone volume to a comfortable listening
level.

Channel A/B Selection Switch

1. Select the appropriate channel (A/B) for the desired audio
source signal.

NOTE: Remove headphones and lower volume before switch­ing between channels. The signal on one channel may be
louder than the other, resulting in possible hearing damage.

Figure 3. The Remote Headphone Battery Installation.

OWNER’S MANUAL/INSTALLATION GUIDE

6

O

PERATIONPRECAUTIONS

:

• Do not allow liquids or foreign objects to enter the
WH200 IR Transmitter or Headphones.

• If any unit should become wet, turn off all power and let
your authorized Clarion Pro Audio dealer clean or service
the equipment.

DO NOT ATTEMPT TO OPEN OR SERVICE THE IR
TRANSMITTER OR HEADPHONES. THE INTERNAL PARTS
ARE NOT USER-SERVICEABLE. DOING SO WILL VOID THE
WARRANTY.

• Do not drop or excessively jar the WH200 headphones.

• Do not use liquid cleaners on any surfaces. Only use a

soft (cotton or other non-static) cloth to wipe off finger­prints.

• Do not subject the unit to direct sunlight or an extremely

hot environment (e.g., closed windows on a hot summer
day , direct path of heater vent, etc.).

• Avoid using the products under the following conditions:

– After extended parking on an extremely hot or cold day
– Near strong magnetic fields
– In an environment with excessive humidity , dust, or

vibration (e.g., off-road travel, etc.)

I

NSTALLATIONPRECAUTIONS

• This unit operates on an automotive 12-volt negative
ground power source and requires additional mobile audio
and video components for proper operation.

• Before installation, disconnect the (–) negative lead from
the vehicle’s battery.

• Use only supplied screws and hardware. Make sure all
connections and components are fastened securely .

• At the proposed installation sites, make sure there is ade­quate space to accommodate the WH200 IR Transmitter
(see Mounting on page 7).

• Use extreme caution when drilling around electrical
wiring, brake lines, and fuel lines. Check clearances on
both sides of a planned installation surface before drilling

WH200

DUAL CHANNEL INFRARED HEADPHONES

7

Figure 4. The WH200’s input connectors and wiring.

M

OUNTINGDESCRIPTION

Opening

for Cables

Blind Nut

Blind Nut

any holes or installing any screws.

• Always wear protective eyewear when using tools.

• Use only high-quality RCA cables that are no longer than
necessary . Extra-length audio and video cables can cause
signal loss and act as an “antenna” for noise.

• When routing RCA cables, keep them away from power
cables and output speaker wires.

• If a fuse needs replacement, use the same value as the
original. Do not substitute another rating.

OWNER’S MANUAL/INSTALLATION GUIDE

8

Figure 5. The WH200’s input connectors and wiring.

W

IRINGDESCRIPTION

WH200

DUAL CHANNEL INFRARED HEADPHONES

9

OWNER’S MANUAL/INSTALLATION GUIDE

Headphone
indicator illu­minated but no
sound.

Check Battery and
Ground wiring at tran­mitter.

Power wires not
connected.

No power indi­cator on head­phone.

Insert (2) Alkaline AAA
batteries into headphone.

Insert Batteries with
proper polarity.

Batteries not
inserted.

Battery polarity
improper.

System does
not work.

Replace external fuse
with the same value.

Fuse is blown.

No sound from
headphone.

Select the proper audio
channel. (see Page 5)

Place headphone on head
to activate Micro switch.

Wrong audio
channel selected

Micro switch
not activated.

T

ROUBLESHOOTING

Symptom Cause Solution

FCC S

TATEMENT

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a automotive instal­lation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer­ence will not occur in a particular installation.

If this equipment does cause harmful interference to radio or
television reception, which can be verified by turning the unit
off and on, the user is encouraged to consult the dealer or an
experienced radio/television technician for help.

2000-WH200-10 Rev. 0 (3/00)

Clarion Corporation of America

661 West Redondo Beach Blvd

Gardena, CA 90247

800-Go-Clarion

www.clarion-usa.com

©2000 Clarion Corporation, Gardena, CA