VMA633
6.5 INCH WIDE LCD MONITOR
6.5” WIDE ACTIVE MARTIX TFT
VMA633
COLOUR LCD MONITOR
OWNER’S MANUAL
INSTALLATION GUIDE
OWNER’S MANUAL
WARNING!
THE CLARION VMA633 LCD MONITOR IS DESIGNED FOR NAVIGATION PURPOSE AND REAR
SEAT PASSENGER VIEWING ONLY.
THIS PRODUCT IS NOT INTENDED FOR VIEWING MOVIES BY THE DRIVER WHILE THE VEHICLE
IS IN MOTION. SUCH USE MAY DISTRACT THE DRIVER OR INTERFERE WITH THE DRIVER’S
SAFE OPERATION OF THE VEHICLE AND MAY RESULT IN SERIOUS INJURY OR DEATH. SUCH
USE MAY ALSO VIOLATE STATE LAW. CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY
INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY
IMPROPER OR UNINTENDED USES OF THIS PRODUCT.
INTRODUCTION:
The VMA633 is a TFT active matrix colour LCD monitor that delivers a striking picture
with superior image resolution. The Clarion VMA633 is a full-feature 6.5” LCD Colour Monitor
and has the following topics:
● 6.5” wide-screen colour LCD panel.
● A bright vibrant clear screen.
● Video composite & RGB 8-pin DIN Style inputs
● Built-in speaker for navigation announcements
● Universal mount for easy installation in different car types
ABOUT THIS MANUAL AND WARRANTY:
To start enjoying your new Clarion VMA633 monitor, please read the instructions listed in
this manual. Keep all instructions for future reference. Please fill out and send in the
enclosed warranty card to protect your purchase and aid in warranty service. Also, save
your original sales receipt as proof of purchase.
TABLE OF CONTENTS:
INTRODUCTION, ABOUT THIS MANUAL & TABLE OF CONTENTS
PRECAUTIONS & DESCRIPTION OF BUTTONS AND CONNECTORS
DESCRIPTION OF PICTURE ADJUSTMENT
INTRODUCTION
CARE AND MAINTENANCE
WIRING PRECAUTIONS
DESCRIPTION OF INSTALLATION
TROUBLESHOOTING
SPECIFICATIONS
1
1
2
3
3
3
4
5
5
VMA633 6.5” TFT LCD Monitor
PRECAUTIONS:
● This monitor is intended for use in DC 12V, negative ground vehicles.
● Do not operate the monitor in ways other than described in this guide, doing so may cause
damage and void the warranty.
● Be careful not to run down the car’s battery while using a multimedia system with the engine
stopped. Doing so may damage the vehicle’s battery or the multimedia system.
● Do not disassemble or modify monitor. Doing so may damage it and void the warranty.
● Keep moisture away from the set. Water and humidity may damage the internal circuitry.
● Do not let the monitor become overheated. If the temperature inside the vehicle is high or the
monitor has been exposed to direct sunlight, lower the monitor’s temperature before use. (The
liquid crystal panel operates within a temperature range of –1~45°C (30~113°F).
● In extremely cold temperature, the movement of the picture may slow and the picture may
become dark. The monitor will work normally once the temperature increase to its normal
operation range.
● Small black or shiny dots may been see inside the liquid crystal panel. These are normal when
manufacturing liquid crystal products.
DESCRIPTION OF BUTTON AND CONNECTORS:
6.5 INCH WIDE LCD MONITOR
1 2 3 4 5 6
7
8
9
10
11
12
13
VMA633
1. Power Button 6. Source Controls 11.Speaker -
2. Dimmer Sensor 7. Video Composite Input (White w.Black line)
3. Remote Sensor 8. 2-Pin Molex Power Connector 12.Speaker + (White)
4. Picture Controls 9. IR Serial Remote OUT 13.Dimmer Lead
5. Wide Mode Controls 10. 8-Pin RGB input DIN cable (Orange)
D
ESCRIPTION
B
UTTONS
2
OWNER’S MANUAL
DESCRIPTION OF PICTURE ADJUSTMENT:
● Press the PICTURE SELECT button several times, the screen will display the picture control
Bar in the following order sequentially.
(BLANK)àBRIGHTNESSàCONTRASTàCOLOURàTINTàDIMMERàMEM RESET─
● Before the display disappears, use the PICTURE SELECT UP (VOLUME UP) button or PICTURE
SELECT DOWN (VOLUME DOWN) button, to adjust the picture quality.
COLOUR
← →
DOWN UP
● Press the WIDE/NORMAL button, the screen will display 16:9 or 4:3 picture.
● DIMMER
：
Press UP、DOWN or Brightness to choose seven different sets.
Auto Brightness automatically
DASHBOARD Controlled by Dashboard illumination
● MEM RESET
CARE AND MAINTENANCE:
Cleaning the Cabinet:
● Use a soft, dry cloth to gently wipe off any dirt.
● Do not use benzene, thinner, car cleaner, etc., as these substances may damage the
cabinet or cause the point to peel.
Cleaning the LCD Panel:
● Use a soft, dry cloth to gently wipe off any dust.
● The surface is easily scratched, do not rub it with hard objects.
WIRING PRECAUTIONS:
Read all wiring precautions. If you are not sure of the connections, contact your
authorized Clarion dealer.
1.Disconnect the negative (-) lead from the vehicle’s battery before making any
connections.
2.When creating passage holes through metal or plastic, use grommets to
Eliminate any sharp edges created during drilling. This will protect power or
video wires from nicks or damaged causing a possible short circle or failure.
3.When connecting the ground lead, fasten the ground lead (black) securely to
a clean metal plate on the vehicle. Use sandpaper to remote any paint from the
surface where the ground terminal is attached.
DESCRIPTION OF INSTALLATION:
Now the VMA633 is useable with including mounting bracket. The VMA633 monitor
PICTURE ADJUSTMENT
will accept a video signal from any video source with composite video output.
The Infrared
(IR) sensor will work with a Clarion NAX9500E using the CCE-001 adapter and IR
extension cable, which are provided.
3
：
Press UP or DOWN, all sets return the initial value.
VMA633 6.5” TFT LCD Monitor
1. Look over the vehicle for a monitor location. Each vehicle is different and locations
will vary. Make sure the monitor will not interfere with the driver’s safe operation of
vehicle.
2. Once a location has been determined, run the 3.5 mm IR extension, Video Composite
and power Molex connector into the monitor’s mounting location.
3. Plug main cable into the monitor.
4. Run the IR extension, video, and power cables to their respective destinations.
1 RED
2 GREEN
3 BLUE
4 C-SYNC
5 NOT CONNECTED
6 NOT CONNECTED
7 NOT CONNECTED
8 NOT CONNECTED
*CCE-001
2
4 5
3
1
8
7
6
RGB Input DIN Configuration
from Composite Video
Video Source Composite In
To lgnition Fuse
+12V
Ground(To Chassis)
To Remote Onput IR Remote Output
from RGB
Video Source
from RGB Output of RGB Input DIN Connector
NAX9500E
NAX
VS718
Video Out
speaker(-)
speaker(+)
Dimmer Lead
6.5 INCH WIDE LCD MONITOR
VMA633
NOTE:
*These CCE-001 adapt IR of NAX
and/or VS718 to VMA633! Never use
IR connection without CCE-001!
I
NSTALLATION
4
Replace external fuse with the same
1°C (30°F) or
OWNER’S MANUAL
TROUBLESHOOTING:
Symptom Cause Solution
System does not
work
The screen dark. The brightness is adjusted
Fuse is blown.
Power wires are not
connected.
too low.
Usage conditions are poor.
SPECIFICATION:
GENERAL SPECIFICATIONS:
Power Requirement: +12 Volts DC (9-16 Volts DC)
Power Consumption: 9 watts, Power On
Weight 0.5 kg (1.1 lb)
Dimensions (w x h x d): 167 x 121 x 29 mm (6-1/2 x 4-7/10 x 1-3/10 in.)
Included Parts LCD Monitor
MONITOR SPECIFICATIONS:
Display Type: Colour TFT Active Matrix LCD
Screen Size: 6.5” (Panel Dimensions 144.4 x 80.3 mm)
Pixels: 1200 x 234
Screen Resolution: 280,800 dots
Video Input Level(RCA) 1.0 volts peak to peak, NTSC
RGB Input Level 0.75 volts peak to peak, TTL
value.
Check the wire connections and
Connect it properly.
Check that the brightness is proper-
0.8 amps (800mA)
3.5 mm Male to Male IR extension cable (5m)
2-pin Molex Power connector
CCE-001 IR adapter for NAX9500E and/or VS718
Mounting bracket
Speaker extension cable (5m)
ly adjusted, if not adjust it properly.
This may happen if the temperature
in the vehicle is below –
above 45°C (113°F). Check again
when the temperature is between
-1°C (30°F) and 45°C (113°F)
TROUBLE SHOOTING
5
Loading...