Citizen JQ2XXX, WINGMAN V, JQ2 Series, C420, CTZ-E6793 Instruction Manual

CITIZEN QUARTZ

WINGMAN V

Model No. JQ2XXX/

Cal. No. C420

• INSTRUCTION MANUAL

CTZ-E6793

Thank you for purchasing a CITIZEN QUARTZ
WATCH. To ensure correct use, please read these
instructions carefully . Please ensure that the Citizen
International Guarantee Card is included for your
possible claim.

1. FEA TURES

Using the Zone Set Function, this watch shows the
local time of 31 major cities of the world by simple
operation of a button.
It also has the Electroluminesence Display which is
visible in the darkness.

2. P ARTS NAME AND FUNCTION

3. SETTING THE ANALOG TIME DISPLAY

1. Pull out the crown and stop the
seconds hand.

2. Turn the crown and set the
hands to the correct time.

3. Press back the crown to
finalise the setting and start
the watch.

How to adjust the watch to the correct time.

Stop the seconds hand at the “0” position. Move the
minutes hand to a few minutes past the time you want
to set, then move it back to the correct time. Press
the crown back synchronising to the correct time.

4. MODE SELECTION OF THE DIGIT ALDISPLAY

This watch offers the following 7 functions beside the
Time; Calendar, Alarm-1, Alarm-2, Chronograph,
Timer, Zone Set and UTC (Greenwich Time) Monitor.
The watch can be set to those modes in the above
order by pressing the M button.

• The Auto-return to the Time
mode will be activated when the
watch is left in the Alarm-1,
Alarm-2, or Zone Set mode for
more than 2 minutes without
any operation.

When reading this instruction manual please keep
the watch diagram folded out and in view. Symbols
used in the sections on operating instructions
refer to the symbols indicated in this diagram.

Display Function

TME Time
CAL Calendar
AL-1 Alarm-1
AL-2 Alarm-2
CHR Chronograph (Stopwatch)
TMR Timer
SET Zone Set
UTC UTC (Greenwich Time)

5. FUNCTION INDICATOR FOR BUTTONS
OPERATION

6. TIME DIFFERENCE BETWEEN THE LOCAL
TIME AND THE UTC

7. MONITORING THE
UNIVERSAL LOCAL TIME
AND THE CALENDAR

1. Select the TIME or
CALENDAR mode by
pressing the M button.

2. Each time the B button is
pressed, the city name and
its local time (or calendar)
will be shown.

• When the “UP” is shown on

the display of button function,
the city name will change
forward each time the B

button is pressed. When the
“DOWN” is shown, the city

name will change backward.

• Press the A and B button simultaneously to switch
the “UP” and “DOWN” indicator.

• The cities adopting the summertime are indicated
with a circle mark (O), the non-adopting cities are
indicated with a cross mark (X).

• The time difference between the UTC and
summertime shown on the table may be changed
practically according to each country’s summertime
system operation.

8. EL (ELECTROLUMINESCENCE) ILLUMINATION

EL

EL (Electroluminescence) panel is a florescent panel
which becomes illuminant when voltage is applied to it.

EL Illumination

The EL panel will be illuminated under the following
circumstances:

1. When pressing button A in time mode, calendar

mode, zone set mode or UTC mode.

2. When displaying stop state or split time state in

chronograph mode.

EL panel has the following characteristics.

• When the battery voltage decreases, so will the
brightness.

• It is sensitive to dampness.
In case the watch gets wet inside, have it serviced
as soon as possible.

• Depending on the accumulative usage time of the
EL (Emitting time), the brightness will decrease.
If the emitting display starts to go dark, and the face
becomes hard to read, take it to the shop from which
you bought it, or the nearest Citizen Service Centre,
and ask for the EL panel to be replaced or repaired.
You will be charged for the service.

9. SETTING THE DIGIT ALTIME DISPLAY (TME)

When the Local Time adjustment for a city is
completed, the time of the other 31 cities will be
automatically adjusted calculating time differences.

1. Set to the Time mode by pressingM button.

2. Press the B button to select the desired city name
for adjustment.

3. The “ON” or “OF” indicator of the Summertime set
will start flashing by pressing the B button for
about 2 seconds. Set the Summertime by pressing
the A button while the indicator is flashing.

4. To adjust other Time displays, select the digits by
pressing the B button. The flashing digits will
change in the order as shown in the diagram.

5. Adjust the flashing digits by pressing theA button.
Press and hold the A button for rapid advancement.

• Make sure that the AM/PM indicated is correct when

setting the time to the 12-hour display system.

• Auto-Return to the normal time display will activate

when the watch is left in the adjustment mode for
more the 2 minutes.

• The adjustment mode will be directly returned to the

normal time display by pressing the M button.

10. SETTING THE CALENDAR DISPLAY (CAL)

When the local calendar adjustment for a city is
completed, the calendar of other 31 cities will be
adjusted automatically calculating time differences.

1. Set the Calendar mode by pressing the M button.

2. Press the B button to select a desired city for
adjustment.

3. Press and hold the B button for 2 seconds or more.
The Month digits will start flashing for adjustment.
Month can be adjusted by pressing the A button.

4. To adjust other digits, press the B button. The digits
will change as shown on the diagram.

5. Adjust the flashing digits by pressing theA button.
Press and hold the A button for rapid advancement.

• Year can be set from 1995 to 2099.

• Calendar is programmed to be set automatically , so

the month-end adjustment is not required.

• Day of the week is automatically adjusted

synchronising to Month, Date and Year settings.

• Auto-return to the normal display will activate when

the watch is left in the adjustment mode for more
than 2 minutes.

• When the Calendar is set to a non-existent date

(e.g., February 30), the display will show
automatically the first day of the next month when
the display is returned to the normal position.

11. USING THE ALARM-1 AND ALARM-2

(AL-1/AL-2)

The operation of the Alarm-1 and Alarm-2 are the
same except the alarm sound. Once the Alarm is set,
it will ring every day at the set time.

Alarm Setting

1. Set to the AL-1 or AL-2 mode by
pressing the M button.

2. Select a city name to set the
Alarm on each local time by
pressing the B button.

3. Press and hold the B button for
at least 2 seconds or more until
the Hour digits start flashing for
adjustment. Adjust the Hours by

3. pressing the A button. Press and hold the A button

for rapid advancement.

4. To adjust the Minutes digits, press the B button to
change the flashing digits. Adjust the Minutes by
pressing the A button.

5. Press the B button to complete setting, the display
will return to the normal alarm display .

Switching the Alarm ON/OFF

• Press the A button to switch the Alarm on/off in the

Alarm mode.

Alarm Sound

The Alarm will sound for about 20 seconds. Press any
button to stop alarm sound.

• Alarm Monitoring: Press and hold theA button in
the Alarm mode to monitor the alarm sound. The
alarm will sound while the button is pressed.

• The Alarm time setting will be synchronised to
the selection of 12-hour/24-hour system in the
Time mode. Make sure that the AM/PM is set
correctly when the 12-hour system is selected.