Citizen JCTV1600SA, JCTV3075SA Instruction Manual
INSTRUCTION MANUAL / MANUEL D'INSTRUCTIONS
PLEASE READ CAREFULLY AND KEEP FOR REFERENCE
VEUILLEZ LIRE ATTENTIVEMENT ET CONSERVER POUR CONSULTATIONS ULTERIEURES
COMBINATION COLOUR TELEVISION AND
VIDEO CASSETTE RECORDER
COMBINÉ TÉLÉVISEUR COULEUR ET MAGNÉTOSCOPE
ATTENTION
If you purchase a universal remote control from your local retailer, please
contact the remote manufacturer for the required programming code.
Si vous utilisez avec cet appareil une télécommande universelle (autre que
celle vendue avec ce téléviseur), consultez la documentation accompagnant la
télécommande universelle afin de connaître le code numérique correspondant
au téléviseur.
TV/CABLE MODE SELECTION
SÉLECTION DU MODE TV/CABLE
When shipped from the factory, the TV/CABLE menu option is set to the "CABLE"
(Cable Television) mode.
If not using CABLE, set this menu option to the TV mode.
Lorsque l'appareil sort de l'usine, l'option du menu TV/CABLE est en mode
"CABLE" (câblodistribution).
Si vous n'utilisez pas la câblodistribution, choisissez l'option "TV".
ENGLISH
FRANÇAIS
THE TOLL FREE CITIZEN HELPLINE IS 1-800-663-5954
CALL US IF YOU HAVE ANY PROBLEMS OR QUESTIONS
9am - 5pm (TORONTO TIME) MONDAY TO FRIDAY
NUMERO D'AIDE CITIZEN SANS FRAIS 1-800-663-5954
APPELEZ-NOUS SI VOUS EPROUVEZ DES PROBLEMES OU AVEZ DES QUESTIONS AU
SUJET DE VOTRE NOUVEL APPAREIL CITIZEN
9 h à 17 h (HEURE DE TORONTO) DU LUNDI AU VENDREDI
MODEL NO./MODÈLE NO: JCTV1600SA/JCTV3075SA
WITH YOUR NEW CITIZEN PRODUCT
CITIZEN ELECTRONICS
TORONTO, CANADA
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTEN-
SION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
WARNING:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
CAUTION:
Changes or modifications not expressly approved by the
party responsible for compliance with the FCC Rules
could void the user's authority to operate this equipment.
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be
read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any
recommendations for attachments, as they may
cause hazards.
2
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
8. ACCESSORIES
Do not place this unit on an unstable cart, stand,
tripod, bracket, or table.
The unit may fall, causing serious injury, and
serious damage to the unit.
An appliance and cart
combination should be
moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause
the appliance and cart
combination to overturn.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3126A
IMPORTANT SAFEGUARDS
9. VENTILATION
Slots and openings in the cabinet back or bottom
are provided for ventilation, and to ensure reliable
operation of the unit, and to protect it from overheating. These openings must not be blocked or
covered. The openings should never be blocked by
placing the unit on a bed, sofa, rug, or other similar
surface. This unit should never be placed near or
over a radiator or heat source. This unit should not
be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have
been adhered to.
10. POWER SOURCES
This unit should be operated only from the type of
power source indicated on the rating plate. If you
are not sure of the type of power supply to your
home, consult your appliance dealer or local power
company. For units intended to operate from battery
power, or other sources, refer to the operating
instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternatingcurrent line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
polarized plug, if your unit is equipped with a 3-wire
grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This too, is a safety feature. If you are
unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the groundingtype plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your unit from a lightning storm, or when
it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent
damage to the unit due to lightning and power line
surges.
14. POWER LINES
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to
keep from touching such power lines or circuits, as
contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as
this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit,
as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never
spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected
to the unit, be sure the antenna or cable system is
grounded to provide some protection against
voltage surges and built-up static charges, Section
810 of the National Electrical Code, ANSI/NFPA 70,
provides information with respect to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
ENGLISH
3
IMPORTANT SAFEGUARDS
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operat-
ing instructions, as an improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the unit to its normal
operation.
e. If the unit has been dropped or the cabinet has
been damaged.
f . When the unit exhibits a distinct change in
performance, this indicates a need for service.
20. REPLACEMENT PARTS
When replacement parts are required, be sure the
service technician uses replacement parts specified
by the manufacturer or those that have the same
characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
21. SAFETY CHECK
Upon completion of any service or repairs to this
unit, ask the service technician to perform safety
checks to determine that the unit is in proper
operating condition.
22. HEAT
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
23. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the CABLE TV
system installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground
shall be connected to the grounding system of the
building, as close to the point of cable entry as
practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
GROUND CLAMP
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
4
PRECAUTIONS
MOISTURE CONDENSATION
DO NOT OPERATE ANY FUNCTIONS ON THIS UNIT
FOR AT LEAST TWO OR THREE HOURS WHEN
MOISTURE IN THE AIR CONDENSES ON IT. LET THE
UNIT STAND WITH POWER ON (SEE BELOW).
■ WHAT IS MOISTURE CONDENSATION?
When a cold liquid is poured into a glass, for example,
water vapor in the air will condense on the surface of
the glass. This is called moisture condensation.
■ MOISTURE WILL CONDENSE ON THE UNIT IN
THE FOLLOWING CASES:
• When you move the unit from a cold to a warm place.
• After heating a cold room or under extremely humid
conditions.
■ WHEN YOU EXPERIENCE THE ABOVE CONDITIONS,
Plug the power cord into an AC outlet, press the
POWER button to turn on and leave the unit at room
temperature until moisture condensation disappears.
Depending on the surrounding conditions, this may
take two or three hours.
LOCATION AND HANDLE
• If you cause a static discharge when touching the unit,
and the unit fails to function, simply unplug the unit
from the wall outlet, wait 10 minutes and plug it back
in. The unit should return to normal operation.
• Avoid extreme heat or cold. (41°F/5°C - 104°F/ 40°C)
• Do not place the unit on or near appliances which may
cause electromagnetic interference (e.g. speakers,
etc). Doing so may cause erratic operation of the unit
including picture and/or sound distortion or noise.
• Avoid extreme moisture and dust.
• The ventilation holes prevent overheating. Do not
block or cover these holes. Especially avoid covering
the holes with soft materials such as cloth or paper.
• Do not insert fingers or any other objects into the
cassette loading slot. Do not spray cleaner or wax
directly on the unit or use forced air to remove dust.
• Avoid places subject to strong vibration. Use in a
horizontal (flat) position only.
• Keep the unit away from flower vases, sinks, etc.
If liquids should be spilled into the unit, serious damage
will result. If you spill any liquids into the unit, unplug the
AC power cord immediately and consult qualified
service personnel before attempting to use it again.
• When you finish operating the unit, always unload the
cassette and turn off the power.
• When you leave your home for a long time, unplug the
AC power cord.
• To protect the unit from a lightning storm, unplug the
AC power cord from the wall outlet and disconnect the
antenna.
POWER SOURCE
Use the AC polarized line cord provided for operation on
AC. Insert the AC cord plug into a standard 120V 60Hz
polarized AC outlet.
NOTES: • Never connect the AC line cord plug to
anything other than the specified voltage (120V
60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a
nonpolarized AC outlet, do not attempt to file
or cut the blade. It is the user's responsibility
to have an electrician replace the obsolete
outlet.
AC Outlet
Wider Hole
and Blade
Polarized AC Cord Plug
(One blade is wider than the other)
ENGLISH
5
PRECAUTIONS
FEATURES
BATTERY INSTALLATION
Slide the battery compartment cover off.
Install two “AAA” batteries (not supplied), paying
attention to the polarity diagram in the battery compartment.
Replace the compartment cover.
BATTERY PRECAUTIONS
The precautions below should be followed when using
batteries in this device:
1 Use only the size and type of batteries specified.
2 Be sure to follow the correct polarity when installing
the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3 Do not mix different types of batteries together (e.g. Al-
kaline and Carbon-zinc) or old batteries with fresh ones.
4 If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
5 Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture (Follow
battery manufacturer’s directions).
EFFECTIVE DISTANCE OF THE
REMOTE CONTROL
Colour TV With Video Cassette Recorder - Unique space
saving design combines a colour TV and a video cassette
recorder.
High Quality Picture Technology - This TV/VCR equipped
with “HQ” incorporates VHS High Quality technology. A
built-in detail enhancer is used to boost the recorded signal
and provide maximum picture quality during playback. It is
compatible with other VHS video cassette recorders.
181 Channel Tuner - Receives standard VHF and UHF
broadcast channels and up to 113 cable channels. The
actual number of channels received depends upon channel
reception in your area or your cable system. (more on pg. 13)
Closed Caption Decoder With Full Text Mode - Displays
text captions or full screen text on the screen for hearing
impaired viewers. (more on pg. 14)
8-Programs/1-Month Programmable Timer With Everyday/Every Week Capability - The built-in timer allows
automatic absentee recording of up to 8 TV programs within
1 month. It is also possible to record a program which is
broadcast at the same time everyday or every week.
(more on pg. 20)
On-Screen TV Display And VCR Programming - When
you select a channel or make other changes, the TV will
show an indicator on the screen for a few seconds. Timer
recording can be programmed and confirmed on the
screen. (more on pg. 14)
Picture Adjustments Using The Remote Control - The
On-Screen display allows precise remote control adjustment of BRIGHTNESS, CONTRAST, COLOUR, TINT and
SHARPNESS. (more on pg. 17)
Automatic Playback/Rewind-Stop-Eject - When loading a
cassette tape without the erase prevention tab, this TV/VCR
will automatically play back the cassette tape at the correct
speed. When a tape reaches its end during play-back,
recording
forward, it will automatically stop, rewind, stop and eject the
tape. (more on pg. 18)
(except during OTR and Timer Record) and fast
15 FEET (5m)
30˚
30˚
NOTES: • When there is an obstacle between the TV/VCR
and the remote control, the remote control may
not operate.
• When direct sunlight, an incandescent lamp,
fluorescent lamp or any other strong light
shines on the Remote sensor of the TV/VCR,
the remote operation may be unstable.
6
Programmable ON/OFF Timer - Allows you to automatically
turn on or off the TV/VCR at a set time. (more on pg. 16)
Programmable TV Sleep Timer - Operable from the remote
control, the TV can be programmed up to 120 minutes to turn
off automatically. (more on pg. 14)
Automatic Repeat Play System - When Auto Repeat
option is turned on, the TV/VCR will automatically play back
the same cassette tape repeatedly. (more on pg. 19)
TABLE OF CONTENTS
One-touch Timer Recording (OTR) - Simply by pressing
the REC/OTR button, the TV/VCR can be programmed for
up to 6 hours of recording with an immediate start.
(more on pg. 20)
Audio/Video Input Jacks - A VCR or other video device
may be hooked up to this TV/VCR for dubbing or playback
purposes. (more on pg. 22)
Skip Search - When the SKIP SEARCH button on the
remote control is pressed during playback, the TV/VCR will
automatically search forward in 30 second increments to a
maximum of 3 minutes with each press of the SKIP
SEARCH button, and then return to normal playback.
(more on pg. 19)
2 Speed Picture Search - 3 or 5 times normal speed in SP
mode (7X or 9X in LP and 9X or 15X in SLP). (more on pg. 19)
3 Speed Playback - Plays three tape speeds (SP, LP, SLP).
(more on pg. 18)
2 Speed Record - Records two tape speeds (SP, SLP).
(more on pg. 19)
Real Time Tape Counter With Zero Return - The counter
displays the real tape time and the zero return can be used
to return the tape to a pre-selected position (00:00:00) while
the counter can be used to locate programs.
(more on pg. 21)
Digital Auto Tracking - Automatically adjusts tracking
during playback for the best possible picture.
(more on pg. 18)
CAUTIONS
IMPORTANT SAFEGUARDS ..................................... 2
PRECAUTIONS .......................................................... 5
PREPARATION
FEATURES ................................................................. 6
TABLE OF CONTENTS .............................................. 7
LOCATION OF CONTROLS ....................................... 8
ANTENNA CONNECTIONS ..................................... 10
CABLE TV CONNECTIONS ..................................... 11
SETTING THE LANGUAGE ..................................... 11
AUTO CLOCK SETTING .......................................... 12
MANUAL CLOCK SETTING ..................................... 13
TV OPERTION
TV OPERATION ....................................................... 13
TO MEMORIZE CHANNELS .................................... 15
TO SET THE ON TIMER .......................................... 16
TO SET THE OFF TIMER ......................................... 17
PICTURE CONTROL ADJUSTMENT ....................... 17
ADJUSTING THE PICTURE PREFERENCE ........... 17
PLAYBACK
LOADING AND UNLOADING .....................................
PLAYBACK ............................................................... 18
SPECIAL PLAYBACK ............................................... 19
18
RECORDING
ENGLISH
On-Screen 3 Language Display - You can select one of 3
languages, English, Spanish or French for on-screen
programming.
TV Monitor - When the TV MONI. button on the remote
control is pressed during playback, the TV channel selected
on the TV/VCR can be viewed. (more on pg. 18)
(more on pg. 11)
RECORDING A TV PROGRAM ................................ 19
ONE-TOUCH TIMER RECORDING (OTR) .............. 20
TIMER RECORDING................................................ 20
ADDITIONAL INFORMATION
USING THE REAL TIME TAPE COUNTER.............. 21
USING ZERO RETURN ........................................... 21
VIDEO INDEX SEARCH SYSTEM ........................... 22
DUPLICATING A VIDEO TAPE ................................. 22
TROUBLESHOOTING GUIDE ................................. 23
RECEPTION DISTURBANCES ................................ 25
VIDEO HEAD CLEANING ........................................ 25
SPECIFICATIONS .................................................... 26
LIMITED WARRANTY .............................................. 27
7
LOCATION OF CONTROLS
FRONT REAR
1
2 43 68
5 7
ANT.
15 16
T-REC
REC/OTR
REC/OTR
VOLUME
CHANNEL
PLAY
VIDEO IN AUDIO IN PHONES
F.FWD
REW
STOP/EJECT
POWER
1091112 1413
DESCRIPTION OF CONTROLS
FRONT:
1. Cassette Loading Slot - To insert or remove a
video tape.
2. POWER Button - Press to turn the TV/VCR on or off.
3. REC/OTR Button - Press once to start normal
recording. Additional presses activate One-touch
Timer Recording.
4. T.REC Indicator - Lights when the unit is in the Timer
Record Mode.
5. REC/OTR Indicator - Lights up when the TV/VCR
is recording.
6. CHANNEL
nel for viewing or recording.
7. PLAY Button - Press to play a prerecorded tape.
8. REW (Rewind) Button - In the Stop mode, this
button rapidly winds the tape backwards. In the
Play mode, this button activates reverse search.
9. Remote Sensor - Signals from the Remote Control
are received here.
/ Buttons - Press to select a chan-
10. VOLUME / Buttons - Press to raise or lower
the level of the sound.
11. STOP/EJECT Button - Press once to stop the tape
in any mode. Press again to eject the tape.
12. F.FWD (Fast Forward) Button - In the Stop mode,
this button rapidly winds the tape forward. In the
Play mode, this button activates forward search.
13. AUDIO/VIDEO IN Jacks - Audio and video signal
cables from an external source can be connected
here.
14. PHONES Jack - Plug monaural headphones or an
earphone with a 3.5 mm miniplug into this jack for
private listening.
REAR:
15. UHF/VHF Antenna Jack - Connect the 75 ohm
coaxial cable from the antenna or Cable TV service
to this jack.
16. AC Power Cord - Connect to a 120V, 60Hz outlet.
8
1
11
12
2
13
21
26
14
3
4
15
22
28
27
ENGLISH
5
6
7
8
9
16
17
18
19
20
10
DESCRIPTION OF CONTROLS
1. POWER Button - Press to turn the TV/VCR on. Press
again to turn the TV/VCR off.
2. Direct Channel Selection Buttons (0-9) - Allows
direct access to any channel.
3. MENU Button - Press to display the On-Screen menu
function.
4. VOL + / – and B / A (cursor) buttons
VOL + / – :
button to decrease the volume level.
B / A (cursor) : Select an item or adjust the setting in
the menu.
5. INPUT SELECT Button - Switches the program for
viewing between the VCR and external input sources.
6. REW (Rewind) Button - In the Stop mode, this button
rapidly winds the tape backwards. In the Play mode,
this button activates reverse search.
7. INDEX + / – buttons - Search for the INDEX mark of a
tape.
8. REC/OTR Button - Press once to start normal
recording. Additional presses activate One-touch
Timer Recording.
9. AUTO TRACKING Button - Allows automatic adjustment of tracking to minimize picture noise during
playback.
10. SPEED Button - Sets the tape speed for recording.
11. EJECT Button - Press to eject the tape.
12. TV MONI. Button - Used to temporarily view a TV chan-
nel selected on the VCR while in the playback mode.
13. TV/CAP/TEXT Button - Switches between Caption, Text
and TV modes for Closed-Captioned programs.
14. PROGRAM Button - Press to confirm the programmed
timer recording and ON/OFF timer.
15. CANCEL Button - Used to clear the selected program
and to move the cursor backward.
16. MUTE Button - Press to turn off the sound. Press
again to turn the sound back on.
17. F.FWD (Fast Forward) Button - In the Stop mode, this
button rapidly winds the tape forward. In the Play
mode, this button activates forward search.
Press the + button to increase, or the –
23
29
24
30
25
18. PAUSE/STILL Button - During recording, this button
temporarily stops the tape. During playback, it stops
the tape and displays a still image on the TV screen.
19. SKIP SEARCH Button - Press in the playback mode
to search forward in 30 second increments to a
maximum of 3 minutes.
20. COUNTER RESET Button - Used to reset the counter
to “00:00:00”.
21. CALL Button - Displays the present time/day of the
week, channel, counter, speed selection (and VCR
mode if VCR is playing) on the TV screen.
22. CH (CHANNEL)
CH (CHANNEL)
to a higher numbered channel set into memory. Press
? ?
the
? button to change to a lower numbered channel
? ?
set into memory.
▲ / ▼ (cursor) : Selects an item in the menu.
23. PLAY Button - Press to play a prerecorded tape.
24. TIMER REC Button - Used to set the TV/VCR to start
recording at a preset time.
25. TRACKING + / – Buttons - During playback, they are
used to adjust tracking manually.
26. SLEEP Button - Sets the TV to turn off automatically
after up to 120 minutes.
27. QUICK VIEW Button - Switches between the present
channel and the last channel selected.
28. ENTER Button - Press to enter or select information
for on-screen operations.
29. STOP Button - Press once to stop the tape.
30. ZERO RETURN Button - Use to stop the tape when the
counter reaches “00:00:00”.
M / ?M / ?
M / ? and ▲ / ▼ (cursor) buttons
M / ?M / ?
M / ?M / ?
M / ? : Press the
M / ?M / ?
MM
M button to change
MM
ATTENTION
If you purchase a universal remote control from your
local retailer, please contact the remote manufacturer
for the required programming code.
9
ANTENNA CONNECTIONS
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna
system. If you are using a cable TV service (CABLE), see page 11 for Cable TV connections.
Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire
Connect the 75 ohm cable from the combination VHF/UHF antenna to the antenna jack.
If your combination VHF/UHF antenna has a 300 ohm twin-lead wire, the use of the 300-75 ohm matching
transformer may be necessary.
Antenna jack
ANT.
75 ohm
Coaxial
Cable
300-75 ohm Matching Transformer
Antenna jack
ANT.
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires
Connect the UHF 300 ohm twin-lead wire to the combiner (not supplied). Connect the VHF 300 ohm twin-lead wire to
the 300-75 ohm matching transformer. Attach the transformer to the combiner, then attach the combiner to the
antenna jack.
Antenna jack
ANT.
300-75 ohm matching
transformer
)
)
Combiner
UHF 300 ohm
VHF 300 ohm
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires
Connect the VHF 75 ohm cable and UHF 300 ohm twin-lead wire to the combiner (not supplied). Attach the
combiner to the antenna jack.
Antenna jack
ANT.
VHF 75 ohm
Combiner
UHF 300 ohm
10
)
CABLE TV CONNECTIONS
This TV/VCR has an extended tuning range and can tune most cable channels without using a cable TV
converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled.
Descrambling these signals for normal viewing requires the use of a descrambler device which is generally
provided by the cable company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a converter/descrambler box,
connect the CABLE TV 75 ohm coaxial cable directly to the antenna
jack
on the back of the TV/VCR.
75 ohm
coaxial cable
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming
75 ohm coaxial dable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect the output jack
of the converter/descrambler box to the antenna jack on the TV/VCR. Follow the connections shown below. Set the
TV/VCR to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the converter/
descrambler box to select channels.
Incoming 75 ohm
CABLE TV cable
Converter/descrambler
75 ohm cable to TV/VCR
Antenna jack
ANT.
Antenna jack
ANT.
ENGLISH
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH
SCRAMBLED PREMIUM CHANNELS
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the
cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B” position,
you can directly tune any nonscrambled channels on your TV/VCR. With the switch in the “A” position, tune your TV/
VCR to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box
to tune scrambled channels.
Incoming 75
ohm CABLE TV
cable
Converter/descrambler
Splitter
A/B switch
75 ohm cable
A
B
to TV/VCR
Antenna jack
ANT.
SETTING THE LANGUAGE
This TV/VCR can display the on screen language in
English, Spanish or French.
On-screen language selection (step 3) will automatically appear on the screen when you press the MENU
button initially. Select the language you prefer first,
then proceed with the other menu options.
1 Press the MENU button.
Press the B or A button to
select
option.
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
////
CH
MENU
2 Press the ▲ or ▼ button to
select the LANGUAGE option,
then press the
A
button.
3 Press the ▲ or ▼ button to
select the desired language:
English (ENGLISH), Spanish
(ESPAÑOL) or French
(FRANCAIS), then press the
ENTER button.
4 Press the MENU button until the
MENU screen is cleared.
MENU
ENGLISH
ESPAOL
FRANCAIS
ENTER/MENU
CH
CH
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
///
LANGUAGE/IDIOMA/LANGUE
//
11
AUTO CLOCK SETTING
The Auto Clock function will automatically set the
built-in clock (Month, Day, Year and Time) when the
TV/VCR is connected to an Antenna or Cable system
and it is turned off. As the TV/VCR searches for a
receivable station in your area and it receives a
broadcast signal for Auto Clock, the Auto Clock needs
several minutes to set itself.
AUTO CLOCK SETTING
1 Connect the Antenna or Cable system.
• If you use a cable box, turn it on.
2 Plug the AC Power cord to the AC outlet.
3 Make sure the TV/VCR is turned off.
• If you press the POWER button, the Auto Clock set is
not effective.
4 Wait at least three minutes and press the POWER
button.
5 Press the CALL button to check the clock on the screen.
6 If the clock is not set, check the Antenna condition. The
Auto Clock may not function properly if the reception
condition is not good.
AUTO CLOCK ADJUSTMENT
The Auto Clock Adjustment will be performed at 12:00 PM
everyday if you turn off the TV/VCR.
• If you use a cable box and you want Auto Clock adjust-
ment to be performed, the cable box must be left on.
• The Auto Clock Adjustment is not effective when there
is a difference of more than 5 minutes exists between
the built-in clock time and the actual time.
TO SET AUTO CLOCK TO OFF
When shipped from factory the AUTO CLOCK option is set
to ON. If you do not want the Auto Clock set (Adjustment):
1 Turn on the TV/VCR.
2 Press the MENU button.
3 Press the B or A button to select the option.
4 Press the ▲ or ▼ button to select the AUTO CLOCK
option.
5 Press the B or A button to select OFF.
6 Press the MENU button repeatedly to return to the
normal screen.
• When the AUTO CLOCK is set to OFF, the Auto Clock
adjustment does not function.
• Set the clock manually (see page 13).
TO SET STANDARD TIME
In the rare event that you live within broadcast range of
two stations in two different time zones, the TV/VCR
may recognize the wrong station for the Auto Clock set.
To correct the situation:
1 Press the MENU button.
2 Press the B or A button to select the option.
3 Press the ▲ or ▼ button to select the STANDARD
TIME option, then Press the A button.
4 Press the ▲/▼/B/A button to select your time zone,
then press the ENTER button.
ATLANTIC : GMT – 4 hours
(GMT: Greenwich Mean Time)
EASTERN : GMT – 5 hours
CENTRAL : GMT – 6 hours
MOUNTAIN : GMT – 7 hours
PACIFIC : GMT – 8 hours
ALASKA : GMT – 9 hours
HAWAII : GMT – 10 hours
AUTO : AUTO SET
5 Press the MENU button twice to return to the normal
screen.
NOTES: • To be able to select the standard time, the
clock must first be set by “AUTO CLOCK”
once.
• If you live in Newfoundland and the Auto
Clock does not function properly, set the
AUTO CLOCK menu option to OFF and set
the clock manually.
DAYLIGHT SAVING TIME SETTING
You can set the Daylight saving time automatically or
manually.
1 Press the MENU button. Press
the B or A button to select the
option.
2 Press the ▲ or ▼ button to select
the DAYLIGHT SAVING TIME
option, then press the A button.
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
////
3 Press the ▲ or ▼ button to select
one of the options, then press the
ENTER button. Press the MENU
button until the MENU screen is
cleared.
ON: for manual setting
(forward one hour)
OFF: for manual setting
(back one hour)
AUTO: for automatic setting
(read XDS in the signal)
When you want to set the Daylight Saving Time manually,
on the first Sunday in April you set to “ON”, and on the last
Sunday in October you set to “OFF”.
NOTES: • When shipped from factory, the DAYLIGHT
SAVING TIME option is set to AUTO position.
• When the clock is not set, Daylight Saving
Time setting is not available.
• When there is no Daylight Saving Time in your
area, always select OFF position in step 3.
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
///
DAYLIGHT SAVING TIME
//
SAVING TIME
MENU
SAVING TIME
MENU
ON
OFF
AUTO
ENTER/MENU
CHCH
ON
CH
ON
CH
12
VOLUME 32
MANUAL CLOCK SETTING
TV OPERATION
You must set the date and time for Timer Recordings
and ON/OFF Timer.
EXAMPLE: Setting the clock to “8:30 AM”, 30th (SAT)
October, 2004.
1 Press the MENU button.
Press the
the
B or A
option.
button to select
2 Press the ▲ or ▼ button to
select the CLOCK SET option,
then press the A button.
3 Press the B or A button to set the
month, then press the ▼ button.
4 Set the day, year and time as in
step 3.
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
////
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
///
CLOCK SET
////
CLOCK SET
////
SAVING TIME
MENU
SAVING TIME
MENU
MONTH
DAY
YEAR
TIME
ENTER/MENU
MONTH
DAY
YEAR
TIME
ENTER/MENU
CHCH
CHCH
CHCH
10
1(MON)
2004
12:00AM
CHCH
10
30(SAT)
2004
8:30AM
ON
ON
After setting the clock, date and time
starts functioning automatically.
8:30 AM SAT
1 To turn on the TV/VCR, press the POWER button.
2 Adjust the volume level by
pressing the VOL + or –
button. The volume level will be
indicated on the screen by
green bars. As the volume level
increases, so do the number of
bars. If the volume decreases, the number of green
bars also decreases.
3 Set the TV/CABLE menu option to the appropriate
position (see page 15).
4 Press the Direct Channel selection buttons to select
the channel.
• TV mode direct channel selection
When the TV/CABLE menu option is in the TV
position, all channels can be instantly selected by
using two buttons (for example, to select channel 2,
press “0”, then “2”. If you press only “2”, channel
selection will be delayed for a few seconds). For
channels 10 and above, press the 2 digits in order.
• CABLE TV mode direct channel selection
When the TV/CABLE menu option is in the CABLE
TV position, channels can be selected as follows:
• TO SELECT CABLE TV CHANNELS:
1-9 Press “0” twice, then 1-9 as needed.
Example, to select channel 2, press “002”.
10-12 Press “0”, then the remaining 2 digits.
Example, to select channel 12, press “012”.
13-99 Press the 2 digits in order.
Example, to select channel 36, press “36”.
100-125 Press the 3 digits in order.
Example, to select channel 120, press “120”.
ENGLISH
NOTES:
• After a power failure or disconnection of the
power plug, the time display will be lost. In
this case, set the present time again.
• To move cursor backward, press the ▲ button.
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are
pressed, the corresponding
channel will be selected in 2
seconds.
NOTES:
• If a channel with no broadcast is selected,
the sound will automatically be muted.
• If a station being viewed stops broadcasting,
the TV will automatically shut itself off after
15 minutes.
CH 012
13
TV OPERATION
MUTE
Press MUTE button to switch off
the sound. The TV/VCR’s sound
will be silenced and “MUTE” will
briefly appear on the screen. The
sound can be switched back on by
pressing this button again or one
of the VOL + or – button.
MM
CHANNEL
Press and release the CH (CHAN-
MM
NEL)
automatically stops at the next
channel set into memory. For
proper operation, before selecting
channels, they should be set into
the memory. See pages 15 and 16
“To memorize channels”.
??
M or
? button. The channel
MM
??
M/
MM
??
?
??
MUTE
CH 012
CALL
Press the CALL button. The clock, date, channel number,
real time tape counter, tape speed and VCR operation will
be indicated.
Press the CALL button again to disappear the call display.
Current time
8:47AM THU CH 012
00:04:38 SP
Real Time Counter
NOTE: To listen through the headphones, insert a
headphones (not supplied) with a 3.5 mm mini
plug into PHONES jack on the front. The sound
from the TV speaker is muted.
Channel No.
Auto Repeat
Tape In
Tape Speed
VCR operation
: Play
: Rewind
: Fast-forward
: Eject
: Recording
: Pause
: Stop
0
0
: Zero return
(Rewind)
: Zero return
(Fast-Forward)
SLEEP
To set the TV/VCR to turn off after a preset amount of
time, press the SLEEP button on the remote control.
The clock will count down 10 minutes for each press of
the SLEEP button (120, 110, ...10, 0). After the sleep time
is programmed, the display will appear briefly every ten
minutes to remind you that the sleep timer is operating.
To confirm the sleep timer setting,
press the SLEEP button and the
remaining time will be momentarily
displayed. To cancel the sleep timer,
press the SLEEP button repeatedly
until the display turns to 0.
SLEEP
120
QUICK VIEW
This button allows you to go back
to the last channel selected by
pressing the QUICK VIEW button.
Press this button again to return to
the last channel you were watching.
CH 012
TV/CAPTION/TEXT
WHAT IS CLOSED CAPTIONING?
This television has the capability to decode and display
Closed Captioned television programs. Closed
Captioning will display text on the screen for hearing
impaired viewers or it will translate and display text in
another language.
Press the TV/CAP/TEXT button to switch between
normal TV and the two closed
caption modes (captions and full
screen text). Closed captioning will
display text on the screen for
hearing impaired viewers.
NOTES:
• If using an indoor antenna or if TV reception
is very poor, the Closed Caption Decoder text
may not appear. In this case, adjust the
antenna for better reception or use an outdoor
antenna.
• When activating the Closed Captioned
Decoder, there will be a short delay before
the Closed Captioned text appears on the
screen.
• Closed Captioned TV programs can be
recorded and played back on a VCR with the
Closed Captioned text intact. The Closed
Captioning text will disappear during Cue,
Rewind and Pause modes or if the VCR
tracking is not adjusted properly.
• Closed Captioned text is only displayed in
locations where it is available.
• If the Call display is on, the Closed Captioning
text will not appear.
CLOSED CAPTIONING WITH A VCR
Closed Captioned programs can be recorded and played
back on a VCR with the Closed Captioned text intact.
The Closed Captioned text will disappear during Cue
(Fast Forward Search), Review (Rewind Search) and
Pause Modes or if the VCR tracking is not adjusted
properly.
TO VIEW CLOSED CAPTIONS
Press the TV/CAP/TEXT button on the remote control to
switch between normal TV and the two Closed Caption
Modes (Captions and Full Screen Text).
CAPTION CH 1
14
TO MEMORIZE CHANNELS
Captions: This Closed Caption Mode will display text on
the screen in English or another language (depending
on the setting of the Closed Captions CH. 1 or 2).
Generally, Closed Captions in English are transmitted
on Captions Channel 1 and Closed Captions in other
languages are transmitted on Captions Channel 2.
The Captions will appear in places on the screen where
they will least interfere with the picture, usually on the
bottom of the screen. News programs will usually show
three-line Closed Captions which scroll onto the screen.
Most other shows provide two or three lined Captions
placed near the character who is speaking so the viewer
can follow the dialogue. Words in italics or underlined
describe titles, words in foreign languages or words
requiring emphasis. Words that are sung usually appear
enclosed by musical notes.
Text: The Text Closed Caption Mode will usually fill the
screen with a programming schedule or other information.
After selecting a Closed Caption Mode, it will stay in
effect until it is changed, even if the channel is changed.
If the Captions signal is lost due to a commercial or a
break in the signal, the Captions will reappear when the
signal is received again. If the channels are changed,
the Captions will be delayed approximately 10 seconds.
For television programs broadcasting with Closed Captions, look in your TV guide for the Closed Captions
symbol (CC).
This TV/VCR is equipped with a channel memory
feature which allows channels to skip up or down to
the next channel set into memory, skipping over
unwanted channels. Before selecting channels, they
must be programmed into the TV/VCR’s memory. In
addition to normal VHF and UHF channels, this TV/
VCR can receive up to 113 Cable TV channels. To
use this TV/VCR with an antenna, set the TV/CABLE
menu option to the TV mode. When shipped from the
factory, this menu option is in the CABLE mode.
TV/CABLE SELECTION
When shipped from the factory, the TV/CABLE menu option
is set to the “CABLE”(Cable Television) mode.
If not using CABLE, set this menu option to the “TV” position.
1 Press the MENU button.
2 Press the B or A button to select
CH
the
mode.
3 Press the ▲ or ▼ button to
select the TV/CABLE mode.
4 Press the B or A button to
select the TV or CABLE mode.
The arrow indicates the selected
mode.
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
////
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
////
MENU
MENU
CH
CHCH
CABLE
CH
CHCH
CABLE
ENGLISH
• When selecting Closed Captions, the captioning will
be delayed approximately 10 seconds.
• If no caption signal is received, no captions will
appear, but the television will remain in the Caption
Mode.
• When Captions are being displayed, on-screen
displays, such as volume and mute may not be seen
or may interfere with Closed Captions.
• Misspellings or unusual characters may occasionally
appear during Closed Captioning. This is normal with
Closed Captioning, especially with live programs. This
is because during live programs, captions are also
entered live. These transmissions do not allow time for
editing.
• Some cable systems and copy protection systems
may interfere with the Closed Captioned signal.
• If using an indoor antenna or if TV reception is very
poor, the Closed Caption Decoder may not appear or
may appear with strange characters or misspelled
words. In this case, adjust the antenna for better
reception or use an outdoor antenna.
TV - VHF/UHF channels
CABLE - CABLE TV channels
VHF/UHF/CABLE CHANNELS
TV
VHF
2-13
UHF
14-69
STD / HRC / IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100) (125)
01 (5A)
CABLE
VHF
2-13
5 Press the MENU button until the MENU screen is cleared.
15
TO MEMORIZE CHANNELS
TO SET THE ON TIMER
AUTOMATIC MEMORY TUNING
1 Press the MENU button.
2 Press the B or A button to
CH
select the
mode.
3 Press the ▲ or ▼ button to
select the AUTO CH MEMORY
mode, then press the A button.
The TV/VCR will begin memorizing all the channels available
in your area. Channel numbers
will remain red until auto memorizing is complete.
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
///
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
///
/
MENU
MENU
CH
CHCH
CH
CHCH
4 Press the MENU button until the
MENU screen is cleared.
TO ADD/DELETE CHANNELS
1 Press the MENU button.
2
Press the B or A button to select
the CH mode.
3
Press the ▲ or ▼ button to select
the ADD/DELETE mode, then
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
////
press the A button.
4 Select the desired channel to be
memorized or deleted using the ▲
TV/CABLE
AUTO CH MEMORY
ADD/ DELETE
or ▼ button, or using the Direct
Channel Selection buttons (10
keys, 0-9).
///
ADD
5 Press the B or A button to
select the ADD or DELETE. If you
select an unmemorized channel,
the Channel indication will be red.
If you select the ADD mode, the
0-9
Channel indication changes from red to green and the
channel will be memorized. If you select a memorized
channel, the Channel indication will be green. If you
select the DELETE mode, the Channel indication
changes from green to red and the channel will be deleted from the memory.
6 Press the MENU button until the MENU screen is
cleared.
MENU
MENU
MENU
/////
CH
CHCH
CH
CHCH
CABLE
CABLE
CABLE
CABLE
CH 001
This feature allows you to have the TV/VCR automatically turn “ON” at a predetermined time. If you
program the “ON TIMER” once, the TV/VCR will turn
“on” on the programmed day (daily/weekly) at the
same time to the same channel.
EXAMPLE: Turning on the TV to channel 12 at 7:00 AM,
MONDAY-FRIDAY.
1 Press the MENU button.
Press the B or A button to select
the
option.
2 Press the ▲ or ▼ button to
select the ON/OFF TIMER
option, then press the A button.
3 Press the ▲ or ▼ button to
select the ON TIMER option,
then press the A button.
4 Press the B or A button to set
the desired hour, then press the
▼ button.
5 Set the desired minute, channel
and daily or weekly timer date
as in step 4.
6 Press the B or A button to select
the SET mode, then press the
ENTER button. Press the MENU
button repeatedly to return to normal screen.
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
////
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
///
ON TIMER
OFF TIMER
///
ON TIMER
OFF TIMER
////
ON TIMER
OFF TIMER
////
ON TIMER
OFF TIMER
////
SAVING TIME
MENU
SAVING TIME
MENU
12 : 00AM
CH 001
SUN-SAT
12 : 00AM
MENU
7 : 00AM
CH 001
SUN-SAT
12 : 00AM
ENTER / MENU
7 : 00AM
CH 012
MON-FRI
12 : 00AM
ENTER / MENU
7 : 00AM
CH 012
MON-FRI
12 : 00AM
ENTER / MENU
CHCH
ON
CHCH
ON
CHCH
CANCEL
CANCEL
CHCH
CANCEL
CANCEL
CHCH
CANCEL
CANCEL
CHCH
SET
CANCEL
NOTES: • The TV/VCR will automatically turn off approxi-
mately 1 hour later after the ON TIMER turns on
if no OFF TIMER has been set. To continue
watching the TV, press any button to cancel the
one hour automatic shut off.
• To cancel ON TIMER, follow above steps 1-5,
then press the B or A button to select the
CANCEL. Press the MENU button repeatedly to
return to the normal screen.
• After setting the ON TIMER, the selected cursor
on to OFF TIMER. If you wish to set the OFF
TIMER, press the A button then follow the steps
4-6 on “ TO SET THE OFF TIMER ” .
• If you want to correct the digits while setting,
press the
▲ or ▼
button until the item you want
to correct, then press the B or Abutton to correct
the
desired setting.
16
TO SET THE OFF TIMER
This feature allows you to have the TV/VCR turn
“OFF” automatically at a predetermined time. If you
program the OFF TIMER once, the TV/VCR will
automatically turn “OFF” at the same time everyday.
EXAMPLE: Turning off the TV at 11:30 PM.
SAVING TIME
MENU
SAVING TIME
MENU
12 : 00AM
CH 001
SUN-SAT
12 : 00AM
MENU
CHCH
ON
CHCH
ON
CHCH
CANCEL
CANCEL
1 Press the MENU button.
Press the B or A button to select
option.
the
2 Press the ▲ or ▼ button to select
the ON/OFF TIMER option, then
press the A button.
3 Press the ▲ or ▼ button to select
the OFF TIMER option, then
press the A button.
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
////
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
///
ON TIMER
OFF TIMER
///
PICTURE CONTROL
ADJUSTMENTS
Picture controls are factory preset but you can adjust
them individually as follows:
1 Press the MENU button.
Press the B or A button to select
the
option.
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
///
2 Press the ▲ or ▼ button to select
the PICTURE option, then press
the A button.
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
///
3 Press the ▲ or ▼ button until the
item you want to adjust is
highlighted, then press the B or
A button to adjust the level.
////
Selection Pressing
BRIGHTNESS darker lighter
CONTRAST lower higher
COLOR paler deeper
TINT reddish greenish
SHARPNESS softer sharper
4 Press the MENU button until the MENU screen is
cleared.
NOTE: To reset the picture adjustments to the factory set-
tings, press the CANCEL button.
MENU
/
MENU
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
CANCEL / MENU
CHCHCHCH
CHCH
CHCH
0
+32
0
0
0
4 Press the B or A button to set the
desired hour, then press the ▼
button.
5 Press the B or A button to set the
desired minute, then press the ▼
ON TIMER
OFF TIMER
////
12 : 00AM
CH 001
SUN-SAT
11 : 00PM
ENTER / MENU
CHCH
CANCEL
CANCEL
button.
12 : 00AM
CH 001
SUN-SAT
11 : 30PM
ENTER / MENU
12 : 00AM
CH 001
SUN-SAT
11 : 30PM
ENTER / MENU
CHCH
CANCEL
CANCEL
CHCH
CANCEL
SET
6 Press the B or A button to select
the SET mode, then press the
MENU button repeatedly to return
to the normal screen.
NOTES: • If a station being viewed
stops broadcasting, the TV
will automatically shut
itself off after 15 minutes.
• To cancel OFF TIMER,
follow above steps 1-5,
then press the B or A
ON TIMER
OFF TIMER
////
ON TIMER
OFF TIMER
////
button to select the CANCEL. Press the MENU
button to return to the normal screen.
• To confirm the ON/OFF TIMER:
Press the PROGRAM button twice to indicate
the programs on the screen.
ADJUSTING THE PICTURE
PREFERENCE
You can select four picture modes—Sports, Standard,
Movie, and Memory—as described in the following
table:
1 Press the MENU button.
Press the B or A button to select
the
option.
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
///
2 Press the ▲ or ▼ button to
select PICTURE PREFERENCE
option, then press the A button.
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
///
3 Press the ▲ or ▼ button to select
the desired picture mode, then
PICTURE PREFERENCE
press the ENTER button.
//
Mode Picture Quality
STANDARD Standard picture quality (factory-set)
SPORTS Bright and dynamic picture (factory-set)
MOVIE Movie-like picture setting (factory-set)
MEMORY Your personal preferences (set by you; see
“Picture control adjustments” as left)
4 Press the MENU button until the MENU screen is
cleared.
MENU
/
MENU
STANDARD
SPORTS
MOVIE
MEMORY
ENTER / MENU
CHCHCHCH
CHCH
CHCH
ENGLISH
17
Loading...