Page 1
Cisco Systems, Inc.
www.cisco.com
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the
Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks,
go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does
not imply a partnership relationship between Cisco and any other company. (1110R)
© Cisco Systems, Inc. All rights reserved.
78-21626-02 A0
1 Package Contents
Your Cisco Universal Small Cell (USC) 3331 is shipped with the
following:
• Power supply unit
• Ethernet cable
• This Quick Start Guide
2 Before You Begin
Consider where you want to place your new small cell. Place it on a flat
surface that is:
• somewhere central, away from windows so your small cell provides
the best possible coverage
• at least 30 cm (1 foot) from other wireless broadcasting devices to
avoid possible interference
• convenient to connect to your broadband router or cable modem
Warning
Read the installation instructions before you connect the system to its
power source.
Statement 1004
Warning
Installation of the equipment must comply with local and national
electrical codes.
Statement 1074
Warning
This product relies on the building’s installation for short-circuit
(overcurrent) protection. Ensure that the protective device is rated not
greater than: 15A.
Statement 1005
Warning
In order to comply with FCC radio frequency (RF) exposure limits,
antennas should be located at a minimum of 7.9 inches (20 cm) or more
from the body of all persons.
Statement 332
Note Use only with listed ITE equipment.
If you require assistance installing or operating your small cell, contact customer
support.
For warranty information, refer to:
http://www.cisco-servicefinder.com/WarrantyFinder.aspx
CISCO USC 3331 QUICK START GUIDE
Page 2
3 Connect Your Small Cell
Follow these instructions to connect your USC 3331 for use:
Step 1 Connect one end of the network cable to the small cell Ethernet port and the
other end to your broadband router or cable modem.
Step 2 Conn
ect the power adapter to the power port and to an AC power source.
Step 3 Flip
the power switch up to turn the unit ON.
Step 4 W
ait ten minutes for your small cell to be ready to use.
The status LED stops flashing green and
becomes solid green when your
small cell is ready to use.
Figure 1 Cisco USC 3331 Connections
1
2
3
4
5
381908
1
Status LED
4
Power port
2
Reset button
5
10/100 Base-T Ethernet port
3
Power switch
4 Verify Your Small Cell Operation
The LED display is located on the side of your small cell. Note the color and activity
of the LEDs and refer to this table to diagnose any problems:
Ta b l e 1 USC 3331 Status LED Indications
LED Indication Small Cell State / Action
Off No power—Ensure power supply is connected and turned on
Fast Green Initialization or provisioning—Wait for action to complete
Green In service, no calls or data sessions—Ready to support calls
Slow Green In service with active calls or data sessions
Red blink 1 time
in 4 seconds
No connection to local broadband router—Verify connection
between broadba
nd router and small cell, and verify that the
broadband router is operational
Red blink 2 times
in 4 seconds
No Internet connection—Verify that the broadband router is
connected to the Internet an
d is providing service
Red blink 3 times
in 4 seconds
Interference with other systems—T
ry placing your small cell in
a different place. If this problem persists, contact customer
support
Red blink 4 times
in 4 seconds
Overheating—Verify that the small cell is located where there is
proper air
flow
Red Initial boot—Wait up to 20 minutes; if still red, perform a reset
Cannot create secure connection—Contact customer support
Internal fault—Contact cust
omer support
RF issue, cannot select an RF profile—Verify whether another
small cell
is located in close proximity and if so, relocate unit
Provisioning failure—Contact customer support
5 Safety Instructions
Translated versions of the following safety warnings are provided in Cisco USC 3331
Regulatory Compliance and Safety Information, located on Cisco.com.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could
cause bodily injury. Before you work on any equipment, be aware of the
hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided
at the end of each warning to locate its translation in the translated
safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Loading...