Cisco Systems E-1 6911, E-1 6901 User Manual
APPENDIX
E
Installing the Wall Mount for the Cisco Unified
IP Phone 6901 and 6911
This appendix contains information on installing the wall mount for use with the Cisco Unified IP Phone
6901 and 6911 phones.
Installing a Wall Mount for the Cisco Unified IP Phone 6901
The following section describes how to install the Wall Mount plate for use with the
Cisco Unified IP Phone 6901.
Cisco recommends that you use the Leviton Wall Mount plate (Leviton type number: 4108W-0SP) for
mounting the Cisco Unified IP Phone 6901. The wall mount plate must be ordered separately from the
phone.
Figure E-1 shows a list of items required to mount the Cisco Unified IP Phone 6901 on the wall using
the Leviton Wall Mount plate.
OL-24582-01
Figure E-1 Leviton Wall Mount Plate
A
7864
B
1
253654
2
1 RJ45 Connector 2 Leviton Wall Mount Plate
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
E-1
Installing a Wall Mount for the Cisco Unified IP Phone 6901
Before You Begin
Before you mount the phone on the wall, ensure that the handset rest is such that the receiver will not
slip out of the cradle (Figure E-2).
Figure E-2 Preparing the Handset Hookswitch
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
21 3
192897
4
1 Remove the handset from the cradle and pull the plastic tab from the handset rest.
2 Rotate the tab 180 degrees.
3 Hold the tab between two fingers, with the corner notches facing you. Make sure the tab lines up
evenly with the slot in the handset cradle. (Figure E-2).
4 Press the tab evenly into the slot. An extension protrudes from the top of the rotated tab. Return
the handset to the handset rest.
E-2
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Installing the Phone on Wall Mount Plate
To install the phone on the wall mount plate, follow these steps:
Procedure
Step 1 Plug the telephone line cord (RJ45 connector) into the phone jack at the base of the phone (Figure E-3).
Figure E-3 RJ45 Connector in the Phone Jack
2
Installing a Wall Mount for the Cisco Unified IP Phone 6901
1
1 Network Port on the Phone
2 RJ45 Connector
253655
OL-24582-01
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
E-3
Installing a Wall Mount for the Cisco Unified IP Phone 6901
Step 2 Plug the RJ45 connector into the wall mount phone jack (Figure E-4).
Figure E-4 RJ45 Connector in the Wall Mount Jack
1
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
2
3
4
253656
1 Network Port on the Phone 3 Wall Mount Plate
2 RJ45 Connector 4 Network Port on the Wall Mount Plate
E-4
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
OL-24582-01
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911
Step 3 Slip the mounting holes on the base of the wall mount plate and over the wall mount pins (Figure E-5).
Figure E-5 Mounting Holes
1
2
Installing a Wall Mount for the Cisco Unified IP Phone 6901
1 Mounting Hole on the Phone
2 Wall Mount Pin on the Wall Mount Plate
253657
OL-24582-01
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
E-5
Loading...