Cisco Systems CF2001P User Manual

NEXT

SETUP INSTRUCTIONS

CF2001P

Printer
WARNING
• Do not plug in the power cord or turn on this unit until you are instructed to according to this manual.
CAUTION
• Install this machine so that it can quickly be unplugged from the electrical outlet in case of an emergency. The socket-outlet shall be installed near the machine and shall be easily accessible.
• Keep all packing materials out of the reach of children.
NOTE
• If the CF2001P is connected to the Minolta MircroPress Cluster Printing System, be sure to take back the User Manual for the CF2001P, since it is not needed by the customer.
• Keep all packing materials in a safe place for later use in case they are needed for transportation.

4004-7715-01 © MINOLTA CO., LTD. Printed in Japan

1. Outline of the CF2001P System Setup
NEXTNEXT
NOTE
• Install and setup each option according to the instructions included with the option.
• For information on adjusting each option, refer to the section “10. Adjusting the Options” on page 29.
1-A. Copy Table CT-2
CF2001P
When setting up the system consisting of this unit and its options, set up each unit in the order shown below.
NOTE Set up each unit correctly according to its SETUP INSTRUCTIONS.
2-A. Paper Feed Unit PF-118
3-A. Dehumidifying Heater
*1: U.S.A and Canada only *2: Not available if the MicroPress PrintLink 2020m is installed
4004-7715-01
PF-117
2-B. Large Capacity Cabinet
PF-117
3-B.Dehumidifying Heater
PF-118
4. CF2001P Printer
5. Duplex Unit AD-14
6. Data Terminal DT-105
*1,*2
2-C. Copy Desk CD-2M
10-A. 10-Mailbin Sorter
JS-1002
*2
– 1 –
7. Mechanical Counter
8. I/F Kit
9. Controller
10-B. Finisher FN-107 10-C. Finisher FN-108
C4004U551CA
*2
2. Unpacking
NEXTNEXT
Unpacking the Accessories
1. Remove the accessories from the box, and then check that the following are enclosed.
(1) Imaging units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
(2) Power cord *1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(3) LED cleaning tool *2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(4) LED cleaning paper *2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(5) Manual holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(6) User Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(7) Setup Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(8) Warranty card *3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(9) Power cord instruction *1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(10) Paper size label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(11) Cable clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(12) Support label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(13) Additional information
(Storing the LED cleaning tool) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
*1 For Particular ar ea only. *2 The LED cleaning tool and its paper are not used during setup. Since they will be
needed when the imaging unit is changed or the printer is cleaned, keep them in a safe place for later use.
*3 U .S.A. and Canada only.
CF2001P
Unpacking the Printer
1. Open the printer box, and then remove the box containing the imaging unit.
NOTE Remove the box containing the imaging unit before removing the box from around the printer.
2. Remove the box from around the printer.
3. Remove the printer from the plastic bag.
4. Open the two handle covers, and then pull out the handles.
5. Grasp the two handles on the right side of the printer and the two grips on the left (as shown in the illustration), and then, while keeping the printer level, remove it from its box.
NOTE The printer weighs about 77 kg (169-3/4
C4004U004AA
lbs.). The printer must be lifted by at least two people. When lifting the printer, be care­ful not to strain your back.
C4004U003AA
4004-7715-01
6. Carefully place the printer on a level and sturdy surface, such as a table.
– 2 –
NEXTNEXT
Removing the Protective Tape and Packing Materials
<Outside Surface of the Printer>
Remove the tape affixed to the outside sur­face of the printer.
C4004U005AA
CF2001P
C4004U145AA
Paper take-up
roller
Packing
material
3. Remove the 2 piec es of packing material from the paper-lifting plate.
4. Close the paper drawer.
5. Pull out the paper drawer for Tray 2.
NOTE Be careful not to touch the surface of the paper take-up roller with your hands. If the roller has been t ouched, wipe it with a dry cloth.
<Paper Feed Section>
4004-7715-01
Packing
material
Paper take-up
roller
C4004U024AA
C4004U006AA
1. Pull out the paper drawer for Tray 1.
NOTE Be careful not to touch the surface of the paper take-up roller w ith your hands. If the roller has been touched, wip e it with a dry cloth.
2. Remove the 2 pieces of tape shown in the illustration from the paper-lifting plate.
– 3 –
Tapes
C4004U026AB
6. Remove the 3 pieces of tape affixed to the paper-lifting plate as shown.
7. Remove the packing material from the paper-lifting plate.
8 Close the paper drawer.
3. Installing the Units
NEXTNEXT
Installing the Imaging Units
C4004U011AA
CF2001P
1. Grasp the handle of the front door, and then carefully swing the door open to the right as shown.
2. Pinch the release lever for the yellow imag­ing unit. (The colors of the imaging units are, from the left, yellow, magenta, cyan, and black.)
C4004U144AA
Protective tape
C4004U049AB
4. Remove the packing material from the imag­ing unit slot.
5. Remove the yellow imaging unit from its box and its protective plastic bag, and then place the imaging unit on a stable, level surface, such as a table.
NOTE
• The imaging unit can easily be damaged by light. Therefore, leave the imaging unit in its protective plastic bag unti l immedi­ately before it is to be installed.
• After removing the imaging unit from its protective plastic bag, make sure that it is not exposed to light, and immediately install it into the printer.
4004-7715-01
C4004U047AA
C4004U048AA
3. Swing the release lever toward you.
6. Hold the imaging unit in both hands, tilt it to the left, and then lightly shake it twice in the direction of the tilt. Next, hold the unit tilted to the right, and then lightly shake it twice in the direction of the tilt.
C4660U001AB
– 4 –
Protective sheet
NEXTNEXT
CF2001P
7. Remove the protective tape from the imag­ing unit.
NOTE The clear plastic protective sheet is not packing material; therefore, do no t remove it.
*
C4004U193AA
* The additional protective sheet, indicated by
C4004U052AB
the shaded area, is only attached to the black imaging unit.
8. Keeping the imaging unit level, pick it up by supporting it on the bot tom with your left hand and on the bottom at the front with your right hand.
C4004U215AB
NOTE When holding the imaging unit, be sure to
C4004U217AB
hold it by its bottom cover. If the top imaging unit cover is held, it may fall off or the PC drum installed on the imaging unit may become damaged, resulting in decreased image quality.
NOTE Be sure to inser t the imaging unit until the end of the bottom imaging unit cover con­tacts the back of the imaging unit com part­ment.
NOTE Do not insert the imaging unit into the com­partment at an angle.
10. While keeping the bottom of the imaging unit supported with your left hand, carefully insert the imaging unit with your right hand, as shown, until the cartridge snaps into place.
4004-7715-01
C4004U216AB
C4004U051AC
9. Keeping the imaging unit level, insert the imaging unit as far as possible into the imag­ing unit compartmen t. Insert the imaging unit with the protective sheet(s) attached.
C4004U053AB
11. Pull out the empty imaging unit cover. The empty imaging unit cover for the black imaging unit can simply be pulled out, even if the protective sheets on the imaging unit become caught on the toner hopper lid.
C4004U054AB
– 5 –
Bottom cover
NEXTNEXT
C4004U055AA
C4004U056AA
CF2001P
12. Separate the top and bottom halves of the empty imaging unit cover.
NOTE Since the bottom half of the imaging unit cover will be used when the imaging unit is replaced again, store it in a safe place.
13. Carefully swing the release lever back up to its original position, pushing it in until it locks into place.
NOTE If the release levers are not cor rectly posi­tioned, the front door cannot be closed.
14. Remove the packing materials from the remaining imaging unit slots, and then install the magenta, cyan, and black imaging units in the same way described in steps 2 through 13.
NOTE Be sure to install the imaging units in their correct slots.
15. After all four imaging units have been installed, grasp the handle of the front door, and then carefully swing the door closed as shown.
Installing the Oil-Coating Unit
C4004U173AA
Metal terminals
C4004U149AB
1. Grasp the upper right-side door as shown, and then carefully open the door completely while making sure to support it.
NOTE Be sure to support the upper right-side door while carefully opening it; otherwise, it may become damaged.
NOTE Do not touch the metal terminals at the front of the fusing unit; otherwise, dama ge may occur due to static electricity.
4004-7715-01
C4004U013AA
– 6 –
C4004U150AB
NEXTNEXT
C4004U151AA
CF2001P
2. Remove the two pieces of tape from the lock levers of the oil-coating unit shown.
3. Remove the oil-coating unit from its box.
NOTE When picking up the oil-coat ing unit, pick it up by the two handles (one on each en d of the unit) with both hands.
4. Insert the oil-coating unit, making sure that the two pins (one on each end of the unit) fit into the notches in the printer.
5. Swing the oil-coating unit up to install it.
C4004O153AA
6. Secure the oil-coating unit by moving the two lock levers (one on each end of the unit) toward you.
C4004O154AA
7. Grasp the upper right-side door as shown, and then carefully close it.
4004-7715-01
C4004U152AB
C4004U174AA
– 7 –
NEXTNEXT
Filling the Toner
NOTE
• The toner bot tles a re no t i nclu de d. A b ott le o f to ner i s n eed ed for each col o r ( four in total) and should be purchased separately.
• Be careful no t to spill toner inside t he printer or get tone r on your clothes and hands. If toner gets on your hands, wa sh them using water and a neutral soap. If toner gets in your eyes, immediately r inse them, an d then consu lt a medical pro­fessional.
1. Grasp the toner hopper door as shown, and then carefully swing the door up to open it.
CF2001P
3. Remove the yellow toner bottle from its packaging. Hit the bottom of the bottle against a strong surface, such as a desk or table, four or five times from a height of about 10 cm (4 in.). (Since the toner within the bottle may have become compacted, be sure to break it up by performing this step.)
NOTE Be sure to hit the bottom of the ton er bottle against the strong surface (the opening of the bottle should be pointing up).
4004-7715-01
C4004U058AA
C4004U059AA
2. Open the yellow toner hopper lid (leftmost) by swinging it toward you. (The toner hopper lids are, from the left, yellow, magenta, cyan, and black.)
C4004U010AA
4. While holding the bottle securely, shake it well in all directions to mix up the toner.
C4004U060AA
5. With the rounded side (marked with “”) of the bottle mouth facing towards you, place the toner bottle on top of the hopper, and then press down on the bottle until it snaps into place.
C4004U061AA
– 8 –
CF2001P
NEXTNEXT
6. Fully pull the toner hopper shutter out toward you. Pulling out the toner hopper shutter allows the toner to begin filling the toner hop­per. Check that all of the toner has emptied out of the toner bottle and into the hopper, which may take a while.
9. Carefully close the yellow toner hopper lid.
4004-7715-01
C4004U062AA
C4004U063AA
C4004U064AA
C4004U065AB
NOTE Do not tap on the toner bottle whi le refilling the hopper; ot herwise, the toner may spur t out.
7. Push the toner hopper shutter closed until it snaps into place and closes the bottle.
8. Tilt the toner bottle slightly backward, and then pull the opening of the bottle up and toward you to remove it.
– 9 –
C4004U066AA
C4004U067AA
10. Fill the magenta, cyan, and black toner in the same way (as described in steps 2 through
9).
NOTE Be sure to fill the toner hoppers with the cor­rect color of toner.
11. After all four toner hoppers are filled, grasp the toner supply door as shown, and then carefully swing the door down to close it.
4. Connecting the Cables
NEXTNEXT
CF2001P
1. Make sure that the printer power cord is not plugged into the electrical outlet, and then insert the plug on the end of the power cord into the power cord connector on the printer.
5. Affixing the Support Label
Support label
Affix the support label on the right side of the top of the toner supply door.
NOTE Affix the label that corresponds with the install ed options.
4004-7715-01
C4005U552AA
C4004U139CA
C4004U589AA
2. Insert the plug on the other end of the power cord into an electrical outlet.
– 10 –
6. Installing the Manual Hol der
NEXTNEXT
C4004U553AA
C4004U554AA
C4004U098AA
CF2001P
1. Insert the tab on the bottom of the manual holder into the slot in the printer as shown in the illustration.
2. Insert the tabs on the left and right sides of the manual holder into the correspon di ng slots in the printer.
NOTE If the optional finisher is used, attach the manual holder to the ba ck of the finisher at the position shown, using th e same proce­dure described above.
7. Checking the Operation of the Printer
NOTE Before adjusting the p rin te r, be sure to inst all the int er fa ce ki t an d t he con trol ­ler. For more details on their ins tallation, refer to thei r manuals.
Loading Test Paper
Load test paper specifically for use with X-Rite calibration.
1. Prepare A4-size (or Letter-size) plain paper.
2. Pull out the paper drawer for Tray 1.
C4004U071AA
3. Press down on the paper-lifting plate until it locks into place.
C4004U072AA
4. Slide the adjustable paper guides to the A4(C) (or Letter(C)) paper size.
4004-7715-01
C4004U073AA
– 11 –
CF2001P
NEXTNEXT
5. Load the prepared A4(C)-s ize (or Let ter (C)­size) plain paper into the paper drawer.
Setting Up the Servicing Equipment
Set up the equipment in order to print a test pattern and make the necessary adjustments.
NOTE Do not turn on any equipment until you are instructed to do so.
4004-7715-01
C4004U074AA
C4004U170AA
C4004U075CA
6. Slide the adjustable paper guides against the edges of the paper.
NOTE Check that the adjustable paper gui des are pushed up against the edges of the paper.
7. Close the paper drawer.
8. Make sure that the media type selection dial on the drawer is turned to the setting for plain paper.
9. From the contr ol pa ne l , s el ec t t he si z e of t he test paper loaded into Tray 1.
NOTE For details on specifying settings, refer to the User Manual.
– 12 –
(4)
(5)
(3)
(6)
(7)
(1)
(1) Notebook PC
Starts the External Panel Controller for adjustment.
(2) X-Rite (DTP32)
Color Tone Tester
(3) Selector
Switches between the Notebook PC and the X-Rite, CF2001P
(4) DTP32 cable
Connects between the X-Rite and the connector A of the selector
(5) RS232 straight cable
Connects between COM1 port of the Notebook PC and the connector C of the selector
(6) RS232 straight cable
Connects between the converter and the connector B of the selector
(7) Converter
Converts the RS422 connector to the RS232 connector
(8) IR Port cable
Connects between the CF2001P and the converter
(2)
(8)
CF2001P
NEXTNEXT
Setting Up the Converter (7)
C4004U556AA
C4004U557AA
TERM
O
N
1
S2
CF2001P
1. Remove the converter from its box.
2. Remove the screw at the bottom of the con­verter, and then remove the upper cover.
3. Set the TERM switch (S2) to ON as shown in the illustration.
NOTE
• Set the button on the converte r to “Nor­mal”.
• In order to reduce the risk of damage to the circuit board due t o static electricity, do not touch the circuit board pattern.
• Do not change the setting of any switches other than those specified.
Setting Up the Selector (3)
1. Remove the selector from its box.
C4004U601AA
2. Remove the two screws from the selector, and then remove the upper cover.
C4004U602AA
3. Affix aluminum tape to the converter as shown in the illustration.
Aluminum tape
C4004U603AA
4004-7715-01
C4004U558AA
– 13 –
NEXTNEXT
Connecting the Equipment Cables
C4004U559AA
C4004U560AA
CF2001P
1. Insert a connector on the DTP32 cable (4) into the I/O port on the side of the X-Rite, and then insert the other con nect or of the cable into port B on the selector.
2. Using the RS232 straight cable (5), connect the COM 1 port of the computer to port C on the selector.
NOTE Make sure that the RS 232 straight cable is connected to the COM 1 port of the com ­puter.
3. Using RS232 straight cable (6), connect DB25 of the converter to port A of the selec­tor.
4. Connect the IR port cable (8) to the printer.
C4004U562AA
5. Using a common screwdriver, tighten the four screws shown in the illustration, and then connect the harnesses of the IR port cable to the terminals on the converter.
TXA terminal: brown harness TXB terminal: red harness RXA terminal: orange harness RXB terminal: blue harness
NOTE Be sure to connect the har nesses of the IR port cable to the specified terminals.
4004-7715-01
C4004U561AA
– 14 –
Brown
Red
Blue
Orange
C4004U563AA
C4004U604AA
NEXTNEXT
CF2001P
6. Loosen the screw of the terminal, and then attach the ground wire as shown.
7. Attach the upper cover of the converter.
8. Plug the power cable of the converter into an electrical outlet.
9. Plug the power cable of the X-Rite into an electrical outlet.
X-Rite Caliblation
NOTE
• Start up the External Panel Controller on the Notebook PC before turning on the printer.
• If an er ror message appea rs, follow the instr uctions desc ribed in the mes­sage.
• Do not quit the Exte rnal Panel Controller while it is being use d. If it is quit­ted, restart the printer and the External Panel Controller.
1. Start up the External Panel Controller on the Notebook PC.
2. Set the power switch to “I”.
C4004U564AA
3. Make sure that the selector knob is set to “A”.
C4004U598AA
4004-7715-01
– 15 –
C4004P565CA
NEXTNEXT
CF2001P
4. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
NOTE If the basic screen does no t appear in the External Panel Controller, turn the printer off. Restart the External Panel Controller, and then turn the printer on again.
5. Click [X-Rite Calibration] in the Tech. Rep. Mode screen.
7. After the test patterns are printed, check that the message appears, and then click the Start key in the External Panel Controller.
C4004P569CA
8. Check that the dialog box appears, set the selector knob to “B”, and then click [OK] in the dialog box.
C4004P570CA
4004-7715-01
C4004P597CA
C4004P567CA
Test patterns
C4004U568AA
6. Check the message that appears, and then click the Start key in the External Panel Con­troller. Test patterns are printed for the four colors. (Cyan, Magenta, Yellow, Black)
NOTE
• Since it may take some time to output th e test patterns ( about 2 minutes) , wait until printing is finished.
• During printing, do not open the front door. If the front door is opened, restart the procedure from step 1.
C4004U571AA
9. Check that the dialog box appears, and then click [Yes] in the dialog box.
C4004P572CA
10. When the dialog box appears, the auto-cal strip can be read. Prepare the auto-cal strip.
C4004P573CA
– 16 –
Reading . . .
NEXTNEXT
0.080.08 0.06
CALIBRATION OK
MANU
C4004U574AA
C4004U594CA
C4004P575CA
11. Insert the auto-cal strip into the X-Rite.
NOTE Insert the auto-cal str ip after “INS ERT CAL STRIP” appears on the X-Rite display.
12. Check that the dialog box appears.
NOTE The dialog box appears if the auto-cal str ip was read correctly.
CF2001P
13. Prepare the cyan test pattern, set the X-Rite
1
3
guide to “10”, and then feed the pattern in direction “1” to read the row represented by “A”. Align the test pattern with the guide, and insert the pattern into the X-Rite.
* The arrows indicate the direction that the
D
2
ABC
4
C4004U576AA
pattern should be fed into the X-Rite.
Guide
C4004U577AA
14. Check that the area indicated in the dialog box appears in [OK].
NOTE The area indicated appears in [OK] if the pattern was read correctly.
C4004P578CA
4004-7715-01
– 17 –
CF2001P
NEXTNEXT
1
3
the row represented by “B”. When feeding the test pattern to read the row represented by “B”, turn the paper to feed it in the correct direction without adjust­ing the X-Rite guide.
15. Feed the test pattern in direction “2” to read
3
C4004P580CA
1
NOTE
D
2
ABC
4
C4004U576AA
When reading the row in the test pattern represented by “B” , do not chang e the set­ting of the X-Rite guide.
16. Check that the area indicated in the dialog box appears in [OK].
NOTE The area indicated appears in [OK] if the pattern was read correctly.
C4004P579CA
D
2
ABC
4
C4004U576AA
17. Turn the cyan test pattern to its original ori-
1
3
entation, set the X-Rite guide to “30”, and then feed the pattern in direction “3” to read the row represented by “C”.
18. Check that the area indicated in the dialog box appears in [OK].
NOTE The area indicated appears in [OK] if the pattern was read correctly.
19. Feed the test pattern in direction “4” to read the row represented by “D”. When feeding the test pattern to read the row represented by squares, turn the paper to feed it in the correct direction without adjusting the X-Rite guide.
NOTE When reading the row in the test pattern represented by “D”, do not change the set ­ting of the X-Rite guide.
20. Check that the area indicated in the dialog box appears in [OK].
NOTE The area indicated appears in [OK] if the pattern was read correctly.
2
4004-7715-01
D
ABC
4
C4004U576AA
– 18 –
C4004P582CA
NEXTNEXT
C4004P590CA
C4004P591CA
CF2001P
21. Check that “Read the Pattern of Cyan” dis­appears, and that >> appears beside “Read the Pattern of Magenta”.
NOTE If the cyan test pattern is read correctly, “Read the Pattern of Cyan” disappears from the dialog box.
22. Prepare the magenta test pattern, and then repeat steps 13 through 21 of the above pro­cedure to read the magenta test pattern with the X-Rite.
NOTE If the magenta test patter n is read cor rectly, “Read the Pattern of Mag enta” disappears from the dialog box.
23. Prepare the yellow test pattern, and then repeat steps 13 through 21 of the above pro­cedure to read the yellow test pattern with the X-Rite.
NOTE If the yellow test pattern is read correctly, “Read the Pattern of Yellow” disappears from the dialog box.
A
C4004P592CA
C4004P595CA
B
C4004U593AA
24. Prepare the black test pattern, and then repeat steps 13 through 21 of the above pro­cedure to read the black test pattern with the X-Rite.
25. Check that the dialog box appears, set the selector knob on the selector from “B” to “A”, and then click [OK] in the dialog box.
NOTE Be sure to click [OK] only after the se lector knob has been set.
26. Check that the Tech. Rep. Mode screen is displayed.
4004-7715-01
C4004P597CA
27. Click [Fin. Time].
– 19 –
8. Making System Setting
NEXTNEXT
Checking the Date Setting
C4004P565CA
C4004PU07CA
C4004PU08CA
CF2001P
1. Check that the External Panel Controller appears in the computer screen, and then display the Date/Time Input screen. (For details about displaying the Date/Time Input screen, refer to the Service Manual.)
2. Check that the current date and time settings are correct. If the settings are not correct, use the keypad in the External Panel Con­troller to enter the correct date and time in the upper row of the screen. Example) To specify April 1, 2001 15:30, click: [2], [0], [0], [1], [0], [4], [0], [1], [1], [5], [3], [0]
3. Click [END].
C4004PU09CA
4. Click [Menu].
5. Check that the Basic screen appears on the External Panel Controller.
4004-7715-01
– 20 –
NEXTNEXT
Specifying the Serial Number
NOTE Be sure to specify the serial number. When the serial number is specif ied, the setting s for each unit can b e read by the printer. If the serial number is no t specified, a correctly adjuste d image cannot be printed.
1. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen.(For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
C4004P565CA
2. Click [System Input].
C4004P597CA
3. Click [Serial # Input].
CF2001P
4. Make sure that [Printer] is selected. Using the keypad in the External Panel Controller, enter the printer’s serial number. Repeat this step to enter the serial numbers for [LCC], [Sorter/FN], and [Duplex].
C4004P585CA
5. Click [END].
6. Click [Menu], and then click [Fin. Time].
4004-7715-01
C4004P584CA
– 21 –
NEXTNEXT
Specifying Who Performs Replacements
NOTE The message that appears a unit must be replaced can be changed to indicate that either th e user or the service repr esentative must perform the repl ace­ment. Select the ap pr opr i at e set t ing s de pe nd ing on th e t yp e of se rvi c ing b ei ng performed.
1. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
C4004P565CA
2. Click [System Input].
C4004P597CA
3. Click [Unit Change].
CF2001P
4. Click [User] or [Service] to select whether each unit should be replaced by the user or the service representative.
C4004PU02CA
5. Click [END].
6. Click [Menu], and then click [Fin. Time].
4004-7715-01
C4004P584CA
– 22 –
NEXTNEXT
Printing the List
C4004U071AA
CF2001P
1. Prepare A4-size (or Letter-size) plain paper.
2. Pull out the paper drawer for Tray 1.
3. Press down on the paper-lifting plate until it locks into place.
5. Load the prepared A4(L)-size (or Letter(L)­size) plain paper into the paper drawer.
C4004U087AA
6. Slide the adjustable paper guides against the edges of the paper.
NOTE Check that the adjustable paper g uides are pushed up against the edges of the paper.
4004-7715-01
C4004U072AA
C4004U073AA
4. Slide the adjustable paper guides to the A4(L) (or Letter(L)) paper size.
– 23 –
C4004U172AA
C4004U075CA
7. Close the paper drawer.
8. Make sure that the media type selection dial on the drawer is turned to the setting for plain paper.
9. From the control panel, select the size of the paper loaded into Tray 1.
NOTE For details on specifying settings, refer to the User Manual.
C4004P565CA
NEXTNEXT
C4004P597CA
C4004PU10CA
10. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
11. Click [List Output].
12. Click [Image Processing].
13. Click the [Start] key in the External Panel Controller. A list of image processing set­tings and the values of each counter are printed out on four sheets of A4(L)-size (or Letter(C)-size) plain paper.
14. Click [Menu], and then click [Fin. Time].
CF2001P
15. Check that the message displayed in the control panel changes from “Alert Printing suspended” to “Info”.
16. Exit the External Panel Controller.
NOTE Before connecting or disconnecting the har ­nesses of the IR por t cabl e, be sure to tu rn off the printer and the converter.
4004-7715-01
– 24 –
NEXTNEXT
T o set the “Energy Save Mode” parameter
NOTE When making setti ngs accordi ng to t he custome r’s requests, refer to the procedur e described below.
1. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
2. Click [Utility].
CF2001P
4. Click [Energy Save Mode.]
C4004P600CA
5. Using the keypad in the External Panel Con­troller, enter the desired number of minutes, and then click [Enter].
NOTE Select the [C] (Clear) key to erase the entered number.
4004-7715-01
C4004P565CA
C4004P599CA
3. Click [User’s Choice].
C4004P058CA
6. Click [Exit].
7. Click [Exit].
8. Check that the message displayed in the control panel changes from “Alert Printing suspended” to “Info”.
9. Exit the External Panel Controller.
NOTE Before connecting or disconnecting the har ­nesses of the IR por t cabl e, be sure to tu rn off the printer and the converter.
– 25 –
NEXTNEXT
To set the “Sleep Mode” parameter
NOTE When making setti ngs accordi ng to t he custome r’s requests, refer to the procedur e described below.
1. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
2. Click [Utility].
CF2001P
4. Click [Sleep Mode.]
C4004P600CA
5. Using the keypad in the External Panel Con­troller, enter the desired number of minutes, and then click [Enter].
NOTE Select the [C] (Clear) key to erase the entered number.
4004-7715-01
C4004P565CA
C4004P599CA
3. Click [User’s Choice].
C4004P059CA
6. Click [Exit].
7. Click [Exit].
8. Check that the message displayed in the control panel changes from “Alert Printing suspended” to “Info”.
9. Exit the External Panel Controller.
NOTE Before connecting or disconnecting the har ­nesses of the IR por t cabl e, be sure to tu rn off the printer and the converter.
– 26 –
9. Loading Paper
NEXTNEXT
NOTE For more details about loading paper, refer to the User Manual.
Tray 1
1. Prepare paper that meets this product’s specifications.
2. Pull out the paper drawer for Tray 1.
CF2001P
C4004U074AA
5. Load the paper into the drawer so that the front side of the paper (the side facing up when the package was unwrapped) faces up.
NOTE
• Do not load so much paper that the top of the stack is higher than the mark indicat­ing the maximum paper capacity.
• Be careful not to touch the surface of the paper take-up roller with your hands. If the roller has been touc hed , wi pe it wi th a d ry cloth.
4004-7715-01
C4004U071AA
C4004U072AA
C4004U073AA
3. Press down on the paper-lifting plate until it locks into place.
4. Slide the adjustable paper guides to fit the size of paper to be loaded.
6. Slide the adjustable paper guides against the edges of the paper.
NOTE Check that the adjustable paper g uides are pushed up against the edges of the paper.
C4004U170AA
7. Close the paper drawer.
8. Turn the media type selection dial on the drawer to the setting for the type of paper loaded.
9. From the control panel, select the size of the paper loaded into Tray 1.
NOTE For details on specifying settings, refer to the User Manual.
– 27 –
NEXTNEXT
Tray 2
C4004U076AA
C4004U077AA
C4004U078AA
CF2001P
1. Prepare paper that meets this product’s specifications.
2. Pull out the paper drawer for Tray 2.
3. Press down on the paper-lifting plate until it locks into place.
4. Slide the adjustable paper guides to fit the size of paper to be loaded.
C4004U079AA
C4004O108AA
5. Load the paper into the drawer so that the front side of the paper (the side facing up when the package was unwrapped) faces up.
NOTE
• Do not load so much paper that the top of the stack is higher than the mark indicat­ing the maximum paper capacity.
• Be careful not to touch the surface of the paper take-up roller with your hands. If the roller has been touched, wipe it with a dry cloth.
6. Slide the lateral guides against the edges of the paper.
NOTE Check that the lateral guid es ar e p ushe d u p against the edges of the paper.
7. Close the paper drawer.
4004-7715-01
– 28 –
CF2001P
NEXTNEXT
8. Affix the enclosed paper size label to Tray 2 as shown.
9. Affix the enclosed drawer number label as shown.
10.Adjusting the Options
NOTE
• With the CF2001P, the adjustments of each option are performed with the servicing equ ipment. Th erefore, st art up t he Exter nal Panel Cont roller, and make the adjustments with the appropriate setting.
• After adjusting the options, restart the printer.
Drawer number label
4004-7715-01
Paper size label
C4004U141AA
Checking the Paper Reference Position for PF-118
NOTE
• For details on the installing PF-118, refer to its Setup Instructions.
• To adjust PF-118, follow the instructions below.
• To exit the External Panel Controller, refer to step 14 on page 24.
1. Load A4-size (or Letter-size) paper into the paper drawer of the optional paper feed unit.
2. Check that the External Panel Controller appears in the computer screen, and then display the Tech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
C4004P565CA
3. Click [Machine Adjust].
C4004P597CA
– 29 –
C4004P588CA
NEXTNEXT
C4658P003CA
C4658P005CA
CF2001P
4. Click [PRT Area].
5. Click [Left Margin].
6. Select the key for the paper drawer that is to be adjusted, and then click the Start key in the External Panel Controller. A test page is printed.
a
C4658U028AA
7. Measure margin a from the edge of the paper to the pattern printed in the test page, and then check that the width of the mea­sured margin meets its standard width.
Standard width of the margin (a):
3.0 mm ± 1.0 mm (with Fiery X3e installed)
5.0 mm ± 1.0 mm (with MicroPress PrintLink 2020m installed)
If the width of the measured margin does not meet its standard width, follow the procedure in the next section, “Adjusting the Paper Ref­erence Position for PF-118”, to adjust it.
4004-7715-01
– 30 –
NEXTNEXT
Adjusting the Paper Reference Position for PF-118
1. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
C4004P565CA
2. Click [Machine Adjust].
C4004P597CA
3. Click [PRT Area].
C4004P588CA
4. Click [Left Margin].
CF2001P
C4658O005CA
C4658U024AA
5. Select the paper drawer that you wish to adjust, and then click the up and down arrows in the lower-right corner of the screen to enter the difference between the mea­sured width and the standard width.
6. Print a test page and check the paper refer­ence position. If the width of the measure margin does not meet its standard width, follow the instruc­tions described below.
7. Open the paper drawer for the cassette that needs to be adjusted, and then remove all of the paper.
8. Loosen the two screws on the guide plate at the bottom of the paper drawer.
9. Adjust the guide plate to the appropriate position on the scale inside the paper drawer.
4004-7715-01
C4658U025AA
C4658P003CA
– 31 –
CF2001P
NEXTNEXT
10. Check that the message displayed in the control panel changes from “Alert Printing suspended” to “Info”.
11. Exit the External Panel Controller.
Checking and Adjusting the Paper Reference Position for PF-117
NOTE
• For details on the installing PF-117, refer to its Setup Instructions.
• To adjust PF-117, follow the instructions below.
• To exit the External Panel Controller, refer to step 14 on page 24.
1. Load A4-size (or Letter-size) paper into the paper drawer of the large-capacity cabinet.
2. Check that the External Panel Controller appears in the computer screen, and then display the Tech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
C4004P565CA
3. Click [Machine Adjust].
C4004P597CA
4. Click [PRT Area].
4004-7715-01
C4004P588CA
– 32 –
4004-7715-01
NEXTNEXT
C4658P003CA
C4659P002CB
a
C4658U028AA
CF2001P
5. Click [Left Margin].
6. Select the key for the third paper drawer, and then click the Start key in the External Panel Controller.
7. Measure the margin from the edge of the paper to the pattern printed in the top-right corner of the test page.
Standard width (a):
3.0 mm ± 1.0 m m (with Fiery X3e installed)
5.0 mm ± 1.0 mm (with MicroPress PrintLink 2020m installed)
Click the up and down arrows in the lower­right corner of the screen to enter the differ­ence (in millimeters) between the measured width and the standard width.
8. Print another test page and check the paper reference position.
– 33 –
Checking and Adjusting the Paper Reference Position for AD-14
NOTE
• Perform the procedur e bel ow after adju sting the pap er referenc e positi ons for the paper feed unit and the large-capacity cabinet.
• For details on the installing AD-14, refer to its Setup Instructions.
• To adjust AD-14, follow the instructions below.
• To exit the External Panel Controller, refer to step 14 on page 24.
1. Load A4-size (or Letter size) paper into the paper drawer of the Tray1.
2. Check that the External Panel Controller appears in the computer screen, and then display the Tech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
C4004P565CA
3. Click [Machine Adjust].
C4004P597CA
C4004P588CA
4. Click [PRT Area].
5. Click [Dup. Left Margin].
NEXTNEXT
CF2001P
8. Measure the width of loss for the test pattern printed on the back of the test page.
a
NOTE Do not measure from the back of the te st pattern.
4004-7715-01
C4657P001CA
C4659P002CA
C4004U596CA
6. Click [1st.].
7. Click the Start key in the External Panel Controller. A test page is printed.
– 34 –
C4657U014AA
Standard width (a):
3.0 mm ± 1.0 mm (with Fiery X3e installed)
5.0 mm ± 1.0 mm (with MicroPress PrintLink 2020m installed)
If the measured width of loss does not meet its standard width, click and in the lower-ri g ht c o rner of th e s c r ee n to ad j us t t h e width. Print another test page and check the printed image.
9. Adjust the paper reference positions for the 2nd, 3rd and 4th drawers in the same way (by repeating steps 6 through 8).
NOTE The 4th drawer is only available if two optional paper feed units are installed.
NEXTNEXT
Checking the Hole-Punching Positions f or FN-107
NOTE
• For details on the installing FN-107, refer to its Setup Instructions.
• To adjust FN-107, follow th e instructions below.
• To exit the External Panel Controller, refer to step 14 on page 24.
CF2001P
6. Click [Hole-Punch].
4004-7715-01
C4004P565CA
C4004P597CA
C4004P588CA
1. Unplug the power cord, and then turn off the printer.
2. Load A4-size (or Letter-size) paper (in land­scape orientation) into Tray 1.
3. Check that the External Panel Controller appears in the computer screen, and then display the T ech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
4. Click [Machine Adjust].
5. Click [Staple/Hole-Punch].
– 35 –
C4683P005CA
4643U031AA
7. Click the Start key in the External Panel Controller.
8. Fold the paper that is fed out in half, and check that the punched holes are aligned.
Standard position: ±2mm
NOTE If the punched holes are not at their stan­dard positions, adjust the hole-punching position.
NEXTNEXT
Setting DT-105 (USA and Canada only)
NOTE
• For details on installing DT-1 05, ref er to the Setup Instructions included with it.
• To set the DT-105, follow the instructions below.
• To exit the External Panel Controller, refer to step 14 on page 24.
CF2001P
<Connecting the Telephone Cables>
• Connect the telephone cable to the jack marked “LINE” on the data terminal.
NOTE If the telephone cable is too short, obtain a different cable with modular plugs.
• Connection examples <When the telephone line is only for the data terminal>
4656M007CA
<When the telephone line is for a phone and the data terminal>
4004-7715-01
<When the telephone line is only for a fax, phone and data terminal>
4656M008CA
4656M009CA
NOTE For details on connecting the fax, refer to the manual for the fax machine.
– 36 –
<Precautions for Connecting a Telephone to the Data Terminal>
NEXTNEXT
• If a telephone is connected to the data terminal, check that the telephone complies with FCC part 68.
• If a telephone which does not comply with FCC part 68 is used, the telephone con­nection may be cut when data terminal transmission begins.
<Data terminal specifications>
Product name: DT-105 (Data Terminal) Transmission speed: 2,400 bps (max) Telephone line: General public telephone line; analog dual-line Power requirements: DC5.2V (supplied via the AC adaptor) Current consumption: 600 mA DC resistance: 149
CF2001P
<Modem Settings>
1. Plug in the AC plug for the data terminal, and then turn it on.
2. Check that the External Panel Controller appears in the computer screen, and then display the Tech. Rep. Mode screen. (For details about displaying the Tech. Rep. Mode screen, refer to the Service Manual.)
C4004P565CA
3. Click [SMART].
4004-7715-01
<Transmission Settings>
– 37 –
C4004P566CA
C4656P002CA
C4656P003CA
4. Click [Modem].
5. Click [END].
1. Click [Common DT].
C4656P004CA
NEXTNEXT
C4656P005CA
C4656P004CA
CF2001P
2. Click [Dial Mode].
3. Select the dial mode of the user’s telephone line.
Push-button.............................. [Tone]
Rotary....................................... [Pulse]
4. Click [END].
5. Click [Auto Receive].
6. Click [Disable].
7. Click [END] twice.
<Date/Time Settings>
1. Click [Date/Time Input].
C4656P003CA
2. Click [Year], click the Clear key in the External Panel Controller, and then use the keypad in the External Panel Controller to enter the correct year.
3. Enter the correct settings for [Month], [Date], and [Hour].
C4656P007CA
4. Click [SET].
4004-7715-01
C4656P006CA
– 38 –
<Maintenance Center (Billing Center) Settings>
NEXTNEXT
NOTE The procedure for making Mainte nance C enter set tings are descr ibed bel ow. If Billing Center settings are nece ssary, specify them using the same procedure after enter ing the Maintenance Center settings.
CF2001P
4. Click [ID Code] again so that it appears in black on a white background.
5. Click [RAM Clear].
<Clearing the Maintenance RAM>
C4656P003CA
C4656P008CA
C4656P009CA
4004-7715-01
1. Click [Maintenance]. (For the Billing Center, click [Billing].)
2. Click [ID Code] so that it appears in white on a black background.
NOTE For the Billing Center, there is no need to enter an ID code.
3. Using the keypad in the External Panel Controller, enter the 7-digit ID code.
NOTE Enter the service representative’s ID code.
– 39 –
C4656P010CA
6. Click [Yes].
7. Click [END].
C4656P011CA
<DT Settings>
NEXTNEXT
C4656P008CA
C4656P009CA
C4656P010CA
CF2001P
1. Click [ID Code] so that it appears in white on a black background.
2. Using the keypad in the External Panel Controller, enter the 7-digit ID code.
NOTE Enter the service representative’s ID code.
3. Click [ID Code] again so that it appears in black on a white background.
4. Click [DT Setting].
5. Click [Password] so that it appears in white on a black background.
C4656P013CA
C4656P014CA
C4656P015CA
6. Using the keypad in the External Panel Controller, enter the 4-digit Center ID.
Password: Center ID code; identification
number of the Center that the data terminal connects to
7. Click [DT-ID] so that it appears in white on a black background.
8. Using the keypad in the External Panel Controller, enter the 6-digit data terminal ID.
NOTE If the number is not 6 -digi ts long, add “0” a t the beginning.
DT-ID: Data terminal ID code; the num-
ber of the data terminal
4004-7715-01
C4656P012CA
– 40 –
<Setting the Telephone Number>
NEXTNEXT
1. Click [TEL No.] so that it appears in white on a black background.
2. Click the Clear key in the External Panel Controller.
C4656P016CA
NOTE
1. Ch eck the screen in the in the Exter nal Panel Controlle r and make sure to ente r the data correctly. If an incorrect number is entered, click the Clear key in the External Panel Controller, and then re-enter the data.
2. If the data t erminal i s connected to an inte rnal switchboa rd, the tim e required to access the outside l ine varies d ependin g on the type of s ystem used . Therefore, enter pause (–) or wait (W) codes for the time required to access the outside line.
• If the ac ces s t im e i s 3 sec ond s o r mo re, e nt er wai t c ode s by sel ecting the E ner gy
Saver key.
• If the access time is less than 3 seconds, enter pause codes by selecting the Inter-
rupt key.
3. Using the keypad in the External Panel Controller, enter the 19-digit telephone number for the Center.
CF2001P
3. If the data terminal is connected to an internal switchboard where the internal and outside lines are of different systems, enter a pulse code (P) for a rotary line or enter a tone code (T) for a push-button line.
Key Function Display
W P
T # *
4. A fter the telephone nu mber has been entere d, call the Center to inform them of the entered settings.
C4656P017CA
Pause
Wait W
Pulse P
Tone T
Extension key (sharp) #
Extension key (asterisk) *
4. Click [END].
4004-7715-01
– 41 –
<Initial Transmission>
RETURN
• To perform the initial user registration for the data terminal after the initial settings have been specified, connect to the Center so the initial information can be sent to the data terminal.
NOTE Call the Center by telephone before and after the initial transmission for verification. In addition, after the tran smission, check that the data (total counte rs, etc.) has been sent correctly to the Center.
1. Click [Initial Transmission].
CF2001P
3. Click the Panel Reset key in the External Panel Controller.
4002U103EA
4. Click [Fin. Time].
Max. trial number reached. The other line is busy.
4004-7715-01
C4656P010CA
2. After the initial transmission is completed, check that “End normal.” appears on the screen.
C4656P018CA
Messages
Line is busy. Not answering.
Connection failed. DT modem error.
Connected. Dialing.
End normal. DT Connection failed.
C4004P566CA
NOTE This completes input of the Maintenance Center settings. If the Billing Center settings must be specified, perform it in the same way .
C4656P019CA
– 42 –
Loading...