Cisco 800 Installation Guide

Cisco 800 Series Integrated Services Router Hardware Installation Guide

April 7, 2015

Cisco Systems, Inc.

www.cisco.com

Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.

THE SPECIFICATIONS AND INFORMATION REGA RDING THE P RODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE W ITH OUT NOT ICE. A LL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILIT Y FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRA NTY FO R THE A CCOMPA NYING PRODUCT A RE SET FORTH IN T HE INFORM ATION P ACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV tech nician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DO CUMENT FILES AND SOFTW ARE OF THESE SUPPL IERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAI M ALL WARRANTIE S, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICUL AR PURPOS E AND NONINFRINGE MENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOS T PROFITS OR LOSS OR DAMAGE TO DATA ARISIN G OUT OF THE US E OR INABILI TY TO USE THIS MA NUAL, EVEN I F CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SU CH DAMA GES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks men tioned are th e property o f their respective owners. The use of the wo rd partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers us ed in th is do cumen t are not in tended to be actual addres ses and phone numbers. Any ex ampl es, co mmand di sp lay output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Cisco 800 Series Integrated Services Router Hardware Installation Guide

CONTENTS

Preface vii

Objective vii Audience vii Organization viii Conventions viii Related Documentation xvi Searching Cisco Documents xvi Obtaining Documentation and Submitting a Service Request xvi

Product Overview 1-1

Cisco 810 Series 1-1

Cisco 812 Series 1-1

General Description 1-1 Hardware Features 1-4 SKU Information 1-9

Cisco 819 Series 1-10

General Description 1-10 SKU Information 1-14 Hardware Features 1-19

Cisco 860, 880, 890 Series 1-33

General Description 1-34 Cisco 860 Series ISRs 1-34 Cisco 860VAE Series ISRs 1-36

Interfaces 1-36 IOS Images 1-36

Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs

Model-Specific Features 1-38 Common Features 1-39

Cisco 880 Series ISRs 1-42

Cisco 880 Series Data Routers 1-43 Cisco 880 Series Voice and Data Routers 1-46 Cisco 880 Series with Embedded WLAN Antennas 1-52 C881G-B/S/V-K9 ISRs 1-54 C881GW-S/V-A-K9 ISRs 1-54

1-38

Cisco Integrated Services Router Hardware Installation Guide

Contents

C881G-U-K9 ISRs 1-55 HSPA+ Versions of the Fixed-Platform ISRs 1-55

Cisco C881, C886, and C887 Series ISRs 1-55

Cisco C881 Router 1-56 Cisco C886VA Router 1-57 Cisco C886VAJ Router 1-58 Cisco C887VA Router 1-59

Cisco C887VAM Router 1-60 Cisco C888 Integrated Services Router 1-62 Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers 1-65

Cisco C881G-4G Integrated Services Router 1-71

Cisco C887VAG-4G Integrated Services Router 1-74

Cisco C896VAG-LTE Integrated Services Router 1-77

Cisco C897VAG-LTE Integrated Service Router 1-81

Cisco C898EAG-LTE Integrated Service Router 1-85

Cisco C899G-LTE Integrated Service Router 1-89 Cisco 890 Series Integrated Service Routers 1-94

Cisco 891, Cisco 892, and Cisco 892F 1-94

Cisco C897VAB-K9 1-104 Cisco C891 Series ISRs 1-107

Cisco C891F Router 1-107

Cisco C891FW Router 1-109 Hardware Features 1-110

Kensington Lock 1-111

Reset Button 1-111

LEDs 1-113

Memory 1-119

USB Port 1-120

Fan 1-121

Power Supply 1-121

Power over Ethernet Module 1-121

3G Cellular Data WAN Connectivity 1-122

Small Form-Factor Pluggable Port 1-124

Feature Summary 1-124

Installing the Router 2-1

Installing the Cisco 810 ISR 2-1

Installing the Cisco 812 ISR 2-1

Items Shipped with your Router 2-2

Items Shipped with your PoE+ Splitter 2-2

Cisco Integrated Services Router Hardware Installation Guide

Installing the Cisco PoE+ Splitter 2-2 Grounding the Cisco 812 ISR 2-18

Installing the Cisco 819 ISR 2-19

Installing the Router 2-22 Mounting the DC Power Supply 2-37

Installing the Cisco 860, 880, 890 ISR 2-38

Equipment, Tools, and Connections 2-39

Items Shipped with your Router 2-39 Additional Items 2-39 Connections 2-40 Ethernet Devices 2-40

Installing the Cisco 860, 880, and 890 Series Routers 2-40

Warnings 2-40 Installing on a Table 2-41 Mounting on a Wall 2-41 Installing the Router Ground Connection 2-44 Installing the FIPS Cover 2-44 Installing Antennas for Cisco 890 Series 2-48 Installing Cisco 890 Series in a Rack 2-52

Installing the C881G-B/S/V-K9 ISR 2-54

Installing Antennas 2-54

Installing the C881GW-S/V-A-K9 ISR 2-54

Installing Antennas 2-54 Installing the C881G-U-K9 ISR 2-54 Installing the Cisco 880G for 3.7G (HSPA+)/3.5G (HSPA) ISRs 2-56

Contents

Connecting the Router 3-1

Cisco 810 Series 3-1

Cisco 819 Series 3-1

Preparing to Connect the Router 3-1

Connecting a PC, Server, or Workstation 3-2

Connecting an External Ethernet Switch 3-3

Connecting a Terminal or PC to the Console Port 3-4

Connecting a Modem to the Console Port 3-5

Connecting the AC Adapter 3-5

Connecting the DC Adapter 3-6

Verifying Connections 3-7

Cisco 860, 880, 890 Series 3-8

Safety Warnings 3-9 Preparing to Connect the Router 3-10

Cisco Integrated Services Router Hardware Installation Guide

Contents

Preventing Damage to the Router 3-11 Connecting a PC, Server, or Workstation 3-12 Connecting a Phone 3-13 Connecting an External Ethernet Switch 3-14 Connecting the V.92 modem Port 3-15 Connecting a Terminal or PC to the Console Port 3-16

Terminal Emulator Settings 3-16 Connecting a Modem to the Auxiliary Port 3-17 Connecting the 3G Card 3-18 Installing the 3G Adapter for Extended Cable/Antenna 3-24 Connecting a Data BRI Port 3-28 Connecting an FE Line to an FE WAN Port 3-30 Connecting a GE Line to an GE WAN Port 3-31 Connecting an xDSL Line 3-31 Connecting Power over Ethernet 3-34 Connecting the AC Adapter 3-35 Connecting an FXS Line 3-39 Connecting an FXO Line 3-40 Connecting a Voice ISDN BRI Line 3-42 Verifying Connections 3-45

Initial Configuration 4-1

Cisco 810 Series 4-1

Cisco 819 Series 4-1

Cisco IOS CLI 4-1

Setup Command Facility 4-1

Verifying the Initial Configuration 4-2

Cisco 860, 880, 890 Series 4-2

Cisco Configuration Professional Express 4-2 Cisco IOS CLI 4-2 Setup Command Facility 4-4 Verifying the Initial Configuration 4-6 Initial Configuration of the Wireless Access Point 4-7

Technical Specifications A-1

Cisco 810 Series A-1

Cisco 812 Series A-1

Router Specifications A-1

Mean Time Between Failure Ground Benign Environment A-4 Cisco 819 Series A-4

Cisco Integrated Services Router Hardware Installation Guide

Router Specifications A-4 Mean Time Between Failure Ground Benign Environment A-8 Supported Power Adapters A-9

Cisco 860, 880, 890 Series A-11

Router Specifications A-12

All Models Except Cisco 860VAE Series A-12 Cisco 860VAE Series A-14 Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 Series A-15 Cisco 870 Series A-16 Cisco 880 Series A-17 Cisco 880G Series 3G Wireless Integrated Services Router A-19 Cisco 880VA Series A-19

Cisco 890 Series A-21 Power Supply A-22 Wireless Access Point A-22 FE and GE Port Pinouts A-23 Console and Auxiliary Port Connector Pinouts A-24 FXS and FXO Port Connector Pinouts A-24 VDSL2 Port Connector Pinouts A-24 ADSL2+ Port Connector Pinouts A-25 V.92 Port Connector Pinouts A-25 G.SHDSL Port Connector Pinouts A-25 Data BRI Port Connector Pinouts A-26 Voice ISDN BRI Interface Pin Numbers and Functions A-27 SFP Port Connector Pinouts A-27 Cable Specifications A-28

Ethernet Cable Specifications A-28

Maximum Cable Length A-28

Contents

Cisco Integrated Services Router Hardware Installation Guide

Contents

Cisco Integrated Services Router Hardware Installation Guide

Preface

This preface describes the objectives, audience, organization, and conventions of this guide and describes related documents that have additional information. It contains the following sections:

• Objective, page vii

• Audience, page vii

Objective

Audience

• Organization, page viii

• Conventions, page viii

• Related Documentation, page xvi

• Searching Cisco Documents, page xvi

• Obtaining Documentation and Submitting a Service Request, page xvi

This guide provides an overview and explains ho w to install, connect, and perform initial configuration for the following series:

• Cisco 810 series ISRs that include both Cisco 812 series and 819 series ISRs

• Wireless and non-wireless Cisco 860 series, Cisco 880 series, and Cisco 890 Integrated Services

Routers (ISRs)

This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar with Cisco routers and Cisco IOS software and features.

Cisco Integrated Services Router Hardware Installation Guide

vii

Organization

This guide is organized into the following chapters and appendix.

Chapter Name Description

Chapter 1 Chapter 1, “Product Overview” Describes the router models and the

Chapter 2 Chapter 2, “Installing the Router” Lists the items shipped with the router, the

Chapter 3 Chapter 3, “Connecting the Router” Describes typical connections for the

Chapter 4 Chapter 4, “Initial Configuration” Provides the procedures for initially

Appendix A Appendix A, “Technical Specifications” Provides the router, port, and cabling

hardware features available.

equipment and tools necessary for installing the router, the safety warnings and guidelines, and the procedures for installing the router.

router, procedures for connecting the router to various devices, and how to verify the connections.

configuring the router settings.

specifications.

Conventions

This section describes the conventions used in this guide.

Note Means reader take note. Notes contain helpful suggestions or references to additional information and

material.

Caution This symbol means reader be careful. In this situation, you might do something that could result in

equipment damage or loss of data.

Tip Means the following information will help you solve a problem. The tip information might not be

troubleshooting or even an action, but could be useful information.

Cisco Integrated Services Router Hardware Installation Guide

viii

Warning

Waarschuwing

Varoitus

IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. Y ou are in a situ ation tha t could cause bod ily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

Attention

Warnung

SÄILYTÄ NÄMÄ OHJEET

IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr . Sie be finden sich in einer Situation, die zu V erletzungen führen

kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Cisco Integrated Services Router Hardware Installation Guide

Avvertenza

Advarsel

Aviso

IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle

persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du

begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser , og kjenn e til standardprosedyrer for å forhindre u lykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de

lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

¡Advertencia!

Varning!

GUARDE ESTAS INSTRUÇÕES

INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular

cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Cisco Integrated Services Router Hardware Installation Guide

Aviso

Advarsel

INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões

corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for

legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Cisco Integrated Services Router Hardware Installation Guide

xii

Cisco Integrated Services Router Hardware Installation Guide

xiii

Warning

When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products.

Statement 371

Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

Statement 378

There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions

. Statement 1015

T o avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

Statement 1021

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available

Cisco Integrated Services Router Hardware Installation Guide

xiv

. Statement 1024

Warning

If the symbol of suitability with an overlaid cross appears above a port, you must no t connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe personal injury or can damage the unit.

Statement 1031

Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards.

Statement 1033

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

Statement 1035

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Statement 1036

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Statement 1037

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Statement 1038

Warning

When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54).

No user-serviceable parts inside. Do not open.

Installation of the equipment must comply with local and national electrical codes.

Statement 1052

Statement 1073

Statement 1074

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Cisco Integrated Services Router Hardware Installation Guide

Warning

Read the installation instructions before connecting the system to the power source.

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed.

Hot surface.

Statement 1077

Statement 1079

Related Documentation

• Regulatory Compliance and Safety Information for Cisco 800 Series Routers

• Cisco IOS Software Releases 12.4 Special and Early Deployments

• Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T

• Cisco IOS Security Configuration Guide, Release 12.4T

• Cisco IOS Security Command Reference, Release 12.4T

Statement 1004

• Cisco CP Express User’s Guide

Searching Cisco Documents

T o search an HTML document using a web bro wser, press Ctrl-F (W indows) or Cmd-F (Apple). In most browsers, the option to search whole words only , in voke case sensiti vity , or search forward and backward is also available.

To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader Search window (Shift-Ctrl-F). Use the Find toolbar to f ind words or phrases within a specific document. Use the Full Reader Search window to search multiple PDF files simultaneously and to change case sensitivity and other options. A dobe Reader’ s online help has mor e information about ho w to search PDF documents.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’ s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/wha tsnew/whatsnew.html

Cisco Integrated Services Router Hardware Installation Guide

xvi

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.

Cisco Integrated Services Router Hardware Installation Guide

xvii

Cisco Integrated Services Router Hardware Installation Guide

xviii

Product Overview

This chapter provides an overview of the features available for the Cisco 812, Cisco 819, Cisco 860, 880, 890 Integrated Services Router (ISR) and contains the following sections:

• Cisco 810 Series, page 1-1

• Cisco 860, 880, 890 Series, page 1-35

Note For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco

800 Series Routers.

Cisco 810 Series

This section contains the following:

• Cisco 812 Series, page 1-1

• Cisco 819 Series, page 1-10

CHA PTER

Cisco 812 Series

This section provides an overvie w of the features a vailable for the Cisco 812 Integrated Services Router (ISR) and contains the following sections:

• General Description, page 1-1

• Hardware Features, page 1-4

• SKU Information, page 1-9

Note For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco

800 Series and SOHO Series Routers.

General Description

The Cisco 812 ISR is a new router that looks like an Access Point with 3G, WLAN, and routing capabilities.

Cisco Integrated Services Router Hardware Installation Guide

1-1

Cisco 810 Series

344399

Chapter 1 Product Overview

The 3rd Generation (3G) is a generation of standards for mobile technology that facilitates growth, increased in bandwidth, and supports more diverse applications.

The Cisco 812 ISR can be powered by an (included) external AC adapter or by a PoE+ capable Ethernet source using an optional Cisco PoE splitter C810-POE-SPL.

A Wireless Local Area Network (WLAN) implements a flexible data communication system frequently augmenting rather than replacing a wired LAN within a b uilding or campus. WLANs use radio freq uency to transmit and receive data over the air, minimizing the need for wired connections. Figure 1-1 shows the Cisco 812 ISR.

Figure 1-1 Cisco 812 ISR

Cisco Integrated Services Router Hardware Installation Guide

1-2

Chapter 1 Product Overview

Figure 1-2 shows the 3G antenna and LEDs display.

Figure 1-2 Cisco 812 ISR 3G and LEDs Display

Cisco 810 Series

1 3G diversity antenna 3 WiF i LED 2 3G main antenna 4 3G LED

344400

Cisco Integrated Services Router Hardware Installation Guide

1-3

Cisco 810 Series

MAIN

C812G

GE WAN

S L

CON/

AUX

5VDC 4.0A

DIV/GPS

3 421

Chapter 1 Product Overview

Figure 1-3 shows the I/O side of the Cisco 812 ISR.

Figure 1-3 Cisco 812 ISR I/O Side

1 GE WAN port 3 Power connection port 2 Console/Aux port 4 Power switch

Hardware Features

The Cisco 812 ISR supports the following hardware features:

Note The WAAS Express feature is not supported. This feature will be supported for 3G and 4G interfaces

with later IOS releases.

Platform Features

The Cisco 812 ISR has the following platform features:

• Platform Features, page 1-4

• Antenna, page 1-5

• LEDs, page 1-5

• Memory, page 1-8

• Power Supply, page 1-8

• 1x GE Enabled WAN (1000/100/10 Base T)

• 2 TNC connectors for 3G main and diversity antenna (diversity antenna multiplexed with GPS)

• 512 MB Compact Flash Memory

• 512 MB DRAM

• AC Power Brick (100–264 V and max 0.5 A)

• Optional PoE+ (802.3at Class 4) Power Splitter

• Built-in Grounding

Cisco Integrated Services Router Hardware Installation Guide

1-4

Chapter 1 Product Overview

Antenna

LEDs

Cisco 810 Series

• Ceiling and Wall Mounting Option

• LED indicators for the platform

The Cisco 812 ISR supports 3G external antenna and WiFi embedded antenna.

3G External Antenna

The Cisco 812 ISR provides two standard p anel-mount TNC connectors to support 3G. Th e main antenna is used for the primary 3G antenna. The second can be used as a diversity recei v e only 3G antenna or an amplified GPS antenna. See Figure 1-2 for the location of the antennas.

WiFi Embedded Antenna

The Cisco 812 ISR supports Dual ports WiFi radios (802.11 a/b/g/n) with embedded 2x3 MIMO. For compliance and safety information, see the Regulatory Compliance and Safety Information for the

Cisco 800 Series and SOHO Series Routers.

The Cisco 812 ISR has two LEDs located on the top side of the router. The 3G LED is located on the lower right side with respect to the Cisco logo. 3G LED supports multip le functions and colors. The W iFi LED is located on lower left sid e with respect to the Cisco logo. Table 1-1 describes the 3G LED for the Cisco 812 ISR.

Table 1-1 Cisco 812 3G LED Descriptions

ROMMON Mode 3G LED LED Color Description

System Yellow FPGA download is complete.

Green (four blinks) ROMMON is running. Off No power.

Incomplete FPGA download.

IOS 3G Mode

3G Service Type White MC8700—2G (GPRS/EDGE)

MC5728—1xRTT

Green MC8700—3G (UMTS)

MC5728—EVDO Rev 0

Light Blue MC8700—3.5G (HSPA)

MC5728—EVDO Rev A

Blue MC8700—3.7G (HSPA+)

MC5728—N/A

Off (solid) No service.

Cisco Integrated Services Router Hardware Installation Guide

1-5

Cisco 810 Series

Chapter 1 Product Overview

Table 1-1 Cisco 812 3G LED Descriptions (continued)

ROMMON Mode 3G LED LED Color Description

RSSI

Fault / Alarm Amber (solid) Fault detected.

1. The LED colors of RSSI can be any of the four colors (White, Green, Light Blue, or Blue) listed under 3G service type.

White, Green, Light Blue, or Blue (solid)

White, Green, Light Blue, or Blue (three blinks and then a long pause)

White, Green, Light Blue, or Blue (two blinks and then a long pause)

White, Green, Light Blue, or Blue (one blink and then a long pause)

Signal > –60 dBm Very strong signal Signal <= –60 to 74 dBm Strong signal.

Signal <= –75 to –89 dBm Fair signal.

Signal <= –90 to –109 dBm Marginal signal.

Off Signal <= –110 dBm

Unusable signal.

Red (four blinks) Temperature alert. Red (solid) Software failure.

Power cycle.

Cisco Integrated Services Router Hardware Installation Guide

1-6

Chapter 1 Product Overview

Table 1-2 describes the WiFi LED for the Cisco 812 ISR.

Table 1-2 Cisco 812 ISR WiFi LED Descriptions

Message Type Color Description

Boot loader status sequence Blinking Green DRAM memory test in progress.

Association status Green Normal operating condition with no

Operating status Blinking Blue Software upgrade in progress.

Boot loader warnings Blinking Blue Configuration recovery in progress.

Cisco 810 Series

DRAM memory test is OK. Board initialization in progress. Initializing FLASH file system. Initializing Ethernet. Ethernet is OK. Starting Cisco IOS. Initialization successful.

wireless client associated.

Blue Normal operating condition with at least

one wireless client associated.

Rapidly cycling through Blue, Green, Red, and White

Blinking Red Ethernet link not operational. Yellow Router is powered up.

Blinking Green LED blinks four times when ROMMON is

Access point location command invoked.

FPGA download is complete.

up.

Boot loader errors Red DRAM memory test failure.

(MODE button pushed for 2 to 3 seconds) Red Ethernet failure. Blinking Green Image recovery in progress (MODE button

released).

Blinking Red and Blue FLASH file system failure. Blinking Red and Off Environment variable failure.

Bad MAC address.

Ethernet failure during image recovery.

Boot environment failure.

No Cisco image file.

Boot failure.

Cisco Integrated Services Router Hardware Installation Guide

1-7

Cisco 810 Series

Memory

Chapter 1 Product Overview

Table 1-2 Cisco 812 ISR WiFi LED Descriptions (continued)

Message Type Color Description

Cisco IOS errors Red Software failure. Try to disconnect and

reconnect the unit power.

Cycling through Blue, Green, Red, and Off

The Cisco 812 ISR supports 512 MB DRAM and 512 MB compact flash memory. The Host router software runs on the first core. The second core runs the WLAN Access Point software.

If WLAN is not supported in an SKU, all 512 MB DRAM memory is allocated to the first core. For the SKUs that support WLAN, 128 MB out of the 512 MB main memory is allocated to the second core.

If WLAN is not supported in an SKU, all 512 MB DRAM compact flash memory is allocated to the first core. For the SKUs that support WLAN, 64 MB out of the 512 MB main memory is allocated to the second core.

General warning.

Power Supply

The following are power adapters supported in the Cisco 812 ISR:

• AC Power Adapter, page 1-8

• PoE+ Splitter, page 1-8

AC Power Adapter

The default configuration is AC adapter that supports up to 4 A of 5 VDC current. The supported AC power adapter is PWR2-20W-AC that has a nominal input voltage of 100 to 240 VAC.

PoE+ Splitter

The Cisco PoE+ splitter (C810-POE-SPL) splits PoE+ into power and GE. It has connectors built into the power supply at both input and output so cables can be used at desired length as an option. Figure 1-4 shows the I/O side of the PoE+ splitter.

Cisco Integrated Services Router Hardware Installation Guide

1-8

Chapter 1 Product Overview

OUTPUT

65 521

3 4

345067

Figure 1-4 PoE+ Splitter I/O Side

1 Grounding location 4 PoE+ input 2 Power status LED 5 Openings for power cord latch to lock into

3 GE0 output 6 Input power connection

Cisco 810 Series

enclosure

SKU Information

Table 1-3 lists the different SKUs available fo r the Cisco 812 ISR. The AP802-A GN-X-K9 (WLAN PID)

is integrated as part of the router for the SKUs that support WLAN and is not orderable separately.

Table 1-3 Supported SKUs

SKU ID WLAN PID Description

C812G+7-K9 — C812 Secure Router Standalone Unit (non-US) 3.7G HSPA

+ Release 7 with SMS/GPS WLAN is not supported.

C812G-CIFI+7-E-K9 AP802-AGN-E-K9 C812 Secure Router (non-US) 3.7G HSPA + Release 7 with

SMS/GPS and Dual WiFi Radio with ETSI

C812G-CIFI+7-N-K9 AP802-AGN-N-K9 C812 Secure Router (non-US) 3.7G HSP A + Release 7 with

SMS/GPS and Dual WiFi Radio with ANZ

C812G-CIFI-V-A-K9 AP802-AGN-A-K9 C812 Secure Router for Verizon EV-DO Rev A with

SMS/GPS and Dual WiFi Radio with FCC

C812G-CIFI-S-A-K9 AP802-AGN-A-K9 C812 Secure Router for Sprint EV-DO Rev A with

SMS/GPS and Dual WiFi Radio with FCC

Cisco Integrated Services Router Hardware Installation Guide

1-9

Cisco 810 Series

Cisco 819 Series

This section provides an overview of the features av ailable for the Cisco 819 and Cisco 819H In tegrated Services Routers (ISRs) and contains the following sections:

• General Description, page 1-10

• SKU Information, page 1-14

• Hardware Features, page 1-20

Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap

that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and

SOHO Series Routers.

General Description

The Cisco 819 Integrated Services Router, part of the Cisco Integrated Services Routers Generation 2 (ISR G2) Family designed in compact hardened and non-hardened form factors, is the smallest Cisco IOS Software router with support for integrated fourth-generation (4G LTE) and third-generation (3G) wireless W AN (mo bile broadband backhaul). The 3G Cisco 819 no w supports Dual 802.11 a/b/g/n radios WiFi. The Cisco 819 ISR machine-to-machine gateway provides a rapidly deployable, highly available, reliable, and secure solution into machine-to-machi ne applications for financial, telemetry, utility, retail, industrial automation, and transportation with comprehensive management capability. Transparently integrated into Cisco IOS Software as an enterprise-class feature, the Cisco 819 Hardened ISR pr o vid es highly secure data, voice, and video communications to stationary and mobile network nodes across wired and wireless links.

Available in both non-hardened (Cisco 819G) and hardened (Cisco 819HG) versions, the Cisco 819 supporting 4G LTE and 3G wireless WAN (WWAN) speeds offers a cost-effective, rapidly deployable, reliable, and secure primary or backup solution. With support for industrial-grade components, the hardened Cisco 819HG extends the ISR machine-to-machine gateway footprint and provides the flexibility for deployment in many different stationary and mobile environments where space, heat dissipation, exposure to extreme temperatures, harsher environments, and low power consumption are critical factors. For mobile applications, Mobile IP deli vers transparent roaming across multipl e wireless networks capable of covering wide geographic areas.

The Cisco 819 ISR is a standard form factor with a commercial operating range. The 3G Cisco 819 ISRs support the 3G speeds (High-Speed PacketAccess Plus [HSP A+] enabling up to 4G speeds and Evolut ion Data Optimized [EVDO Rev A]). They are backward-compatible with High-Speed Packet Access (HSPA), Universal Mobile Telecommunications Service (UMTS), Enhanced Data Rates for Global Evolution (EDGE), General Packet Radio Service (GPRS), and EVDO Rev 0/1xRTT.

The 4G LTE C819 supports the latest Third-Generation Partnership Project (3GPP) Release 8 LTE standards. The Cisco 4G multimode L TE WWAN C819 provides persistent and reliable L TE connecti vity with fallback and transparent handof f to earlier te chnologies. The Cisco 819HG-4G and Cisco 819G-4G support multimode 4G LTE and have embedded Sierra Wireless multimode modem.

The Cisco 819 ISR is a desktop form factor with built-i n wall-mou nt features, floor mount , and DIN rail mount features in selected SKUs. These routers are powered by an external AC power or optional DC adapter. Figure 1-5 shows the Cisco 819HG ISR.

Chapter 1 Product Overview

Beginning with IOS release 15.2(4)M1, the new 3G Cisco 819HGW and Cisco 819HWD ISRs support WiFi radios with a higher memory density and a new barrel-type power connector. A Wireless Local Area Network (WLAN) implements a flexible data communication system frequently augmenting rather

Cisco Integrated Services Router Hardware Installation Guide

1-10

Chapter 1 Product Overview

than replacing a wired LAN within a building or campus. WLANs use radio frequency to transmit and receive data over the air, minimizing the need for wired connections. Figure 1-6 shows the Cisco 819HGW ISR.

The WLAN for 3G Cisco 819HGW and Cisco 819HWD ISRs have the following additional features:

• Dual 802.11 a/b/g/n radios

• External WiFi antenna

• WLAN LED

Note Cisco 819 is used to refer to Cisco 819HG, Cisco 819G, Cisco 819H, Cisco 819HGW, Cisco 819HWD,

Cisco 819HG-4G, and Cisco 819G-4G ISRs unless specifically called out otherwise.

Figure 1-5 Cisco 819HG Integrated Services Router

Cisco 810 Series

283010

Cisco Integrated Services Router Hardware Installation Guide

1-11

Cisco 810 Series

285479

245547

1 43 6 7 9 10 11 12

5 8

Chapter 1 Product Overview

Figure 1-6 Cisco 819HGW Integrated Services Router

Figure 1-7 shows the front panel details of the Cisco 819HG ISR.

Figure 1-7 Cisco 819HG ISR Front Panel

1 3G main antenna 7 FE ports 2 LEDs 8 GE WAN port 3 Reset button 9 Console/Aux port

Cisco Integrated Services Router Hardware Installation Guide

1-12

Chapter 1 Product Overview

344077

21 43 6 7 9 10 11 12

5 8

4 3G mini-USB diagnostic port 10 5 VDC molex power input 5 Diversity/GPS antenna 11 Power switch 6 12-in-1 serial port 12 Ground

Figure 1-8 shows the front panel details of the Cisco 819HGW ISR.

Figure 1-8 Cisco 819HGW ISR Front Panel

Cisco 810 Series

1 3G main antenna 7 FE ports 2 LEDs 8 GE WAN port 3 Reset button 9 Console/Aux port 4 3G mini-USB diagnostic port 10 5 VDC barrel-type power input 5 Diversity/GPS antenna 11 Power switch 6 12-in-1 serial port 12 Ground

Cisco Integrated Services Router Hardware Installation Guide

1-13

Cisco 810 Series

285447

1 43 6 7 9 10 11 13

5 128

Chapter 1 Product Overview

Figure 1-9 shows the front panel details of the Cisco 819 4G LTE ISR.

Figure 1-9 Cisco 819 4G LTE ISR Front P a nel

1 4G antenna connector—M0/MAIN 8 GE WAN port 2 LEDs 9 Console/Aux port 3 Reset button 10 Power input 4 4G/3G port 11 Power switch 5 4G antenna connector—M1/DIV 12 Active GPS antenna connector 6 Serial port 13 Ground 7 FE ports

SKU Information

Note WLAN is not supported.

Table 1-4 lists the different 3G SKUs available for the Cisco 819HG and Cisco 819G ISRs. All SKUs

support external antenna.

Table 1-4 Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs

SKU ID Description

C819HG+7-K9 Compact Hardened 3G IOS Router with Global HSPA + Release 7 based on

MC8705

C819HG-U-K9 Compact Hardened 3G IOS Router with GLOB AL HSPA Release 6 based on

MC8795V

C819HG-V-K9 Compact Hardened 3G IOS Router with Verizon EVDO Rev A based on

MC5728V

C819HG-S-K9 Compact Hardened 3G IOS Router with Sprint EVDO Rev A based on

MC5728V

Cisco Integrated Services Router Hardware Installation Guide

1-14

Chapter 1 Product Overview

Table 1-4 Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs (continued)

SKU ID Description

C819HG-B-K9 Co mpact Hardened 3 G IOS Router with Bharat g eneric EVDO Rev A based

C819G+7-K9 Compact Non-hardened 3G IOS Router with Global HSP A + Release 7 based

C819G-U-K9 Compact Non-hardened 3G IOS Router with GLOBAL HSPA Release 6

C819G-V-K9 Compact Non-hardened 3G IOS Router with Verizon EVDO Rev A based on

C819G-S-K9 Compact Non-hardened 3G IOS Router with Sprint EVDO Rev A based on

C819G-B-K9 Compact Non-hardened 3G IOS Router with Bharat generic EVDO Rev A

Cisco 810 Series

on MC5728V

on MC8705

based on MC8795V

MC5728V

based on MC5728V

Cisco Integrated Services Router Hardware Installation Guide

1-15

Chapter 1 Product Overview

Cisco 810 Series

Table 1-5 lists the different SKUs available for the Cisco 819HGW, Cisco 819H, and Cisco 819HWD

ISRs.

Table 1-5 Supported SKUs for Cisco 819HGW, Cisco 819H, and Cisco 819HWD ISRs

WiFi External Antenna

SKU ID WLAN ID

C819HGW+7-E-K9 AP802H-AGN-E-K9 Yes Cisco 819 Secure Hardened M2M

C819HGW+7-N-K9 AP802H-AGN-N-K9 Yes Cisco 819 Secure Hardened M2M

C819HGW+7-A-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened M2M

C819HGW-V-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened Router

C819HGW-S-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened Router

C819H-K9 — — Cisco 819 Secure Hardened Router

C819HWD-E-K9 AP802H-AGN-E-K9 Yes Cisco 819 Secure Hardened Router

Support Description

GW (non-US) 3.7G HSPA + Release 7 with SMS/GPS and Dual WiFi Radio with ETSI

GW (non-US) 3.7G HSPA + Release 7 with SMS/GPS and Dual WiFi Radio with ANZ

GW (North America) 3.7G HSPA + Release 7 with SMS/GPS and Dual WiFi Radio with FCC for ATT

for Verizon EV-DO Rev A with SMS/GPS and Dual WiFi Radio with FCC

for Sprint EV-DO Rev A with SMS/GPS and Dual WiFi Radio with FCC

with Serial WLAN and 3G are not supported

and Dual WiFi Radio with ETSI

C819HWD-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened Router

Cisco Integrated Services Router Hardware Installation Guide

1-16

3G is not supported

and Dual WiFi Radio with FCC 3G is not supported

Chapter 1 Product Overview

Table 1-6 lists the different 4G LTE SKUs available for the Cisco 819HG and Cisco 819G ISRs.

Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs

SKU ID Mode Operating Regions Frequency Band Description

C819HG-4G-V-K9 LTE—DOrA North America 700 MHz (band 13) or LTE

800/1900 MHz for CDMA 1xRTT, 1xEVDO Rev A

C819G-4G-V-K9 LTE—DOrA North America 700 MHz (band 13) for LTE

800/1900 MHz for CDMA 1xRTT, 1xEVDO Rev A

C819HG-4G-A-K9 LTE—HSPA+/

HSPA/UMTS/ EDGE/GPRS

North America 700 MHz (band 17)/AWS (band

4)/2100MHz (band 1) for LTE 800/850/1900/2100 MHz for

UMTS/ HSPA+/HSPA 850/900/1800/1900 MHz for

GSM/EDGE/GPRS

C819G-4G-A-K9 LTE—HSPA+/

HSPA/UMTS/ EDGE/GPRS

North America 700 MH z(band 17)/AWS(band

4)/2100MHz(band 1) for LTE 800/850/1900/2100 MHz for

UMTS/ HSPA+/HSPA 850/900/1800/1900 MHz for

GSM/EDGE/GPRS

C819HG-4G-G-K9 LTE—HSPA+/

HSPA/UMTS/ EDGE/GPRS

Global 800 MHz (band 20)/900 MHz

(band 8)/1800 MHz (band

3)/2100 MHz (band 1)/2600 MHz (band 7) for LTE

900/2100 MHz for UMTS/ HSPA+/HSPA

900/1800/1900 MHz for GSM/EDGE/GPRS

Compact Hardened Cisco 819 router with multi mode LTE feature dedicated to Verizon Wireless networks. This comes with a Sierra Wireless MC7750 modem.

Compact Non-hardened Cisco 819 router with multi mode LTE feature dedicated to Verizon Wireless networks. This comes with a Sierra Wireless MC7750 modem.

Compact Hardened Cisco 819 router with multi mode LTE feature dedicated to AT&T Wireless networks. This comes with a Sierra Wireless MC7700 modem.

Compact Non-hardened Cisco 819 router with multi mode LTE feature dedicated to AT&T Wireless networks. This comes with a Sierra Wireless MC7700 modem.

Hardened Cisco 819 router with multi-mode LTE feature for global wireless networks. This comes with a Sierra Wireless MC7710 modem.

Cisco 810 Series

Cisco Integrated Services Router Hardware Installation Guide

1-17

Chapter 1 Product Overview

Cisco 810 Series

Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

SKU ID Mode Operating Regions Frequency Band Description

C819G-4G-GA-K9 LTE—HSPA +/

HSPA/UMTS/ EDGE/GPRS

C819G-4G-NA-K9

• LTE

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Global (Europe, Australia and New Zealand)

North America (AT&T, Bell-Canada, Roger, Telus, and other GSM/LTE operators in USA and Canada)

LTE—800 MHz (band 20)/900 MHz (band 8)/1800 MHz (band

3)/2100 MHz (band 1)/2600 MHz (band 7)

3G—800 MHz (band 6)/850 MHz (band 5)/900 MHz (band 8) /1900 MHz (band 2) 2100 MHz (band 1) for UMTS/ HSPA+/HSPA

2G—850/900/1800/1900 MHz for GSM/EDGE/GPRS

LTE:

• AWS (band 4)

• 700 MHz (band 5)

• 850 MHz (band 17)

• 1900 MHz (band 2)

• 2600 MHz (band 7)

UMTS, HSPA+, HSPA:

• 1900 MHz (band 2)

Non-hardened Cisco 819 router with multi-mode LTE feature for global wireless networks. This comes with a Sierra Wireless MC7304 modem.

Non-hardened Cisco 819 router with multi-mode LTE feature for AT & T wireless networks. This comes with a Sierra Wireless MC7354 modem

• AWS (band 4)

• 850 (band 5)

GSM, EDGE, GPRS:

• 850 MHz

• 900 MHz

• 1800 MHz

• 1900 MHz

Cisco Integrated Services Router Hardware Installation Guide

1-18

Chapter 1 Product Overview

Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

SKU ID Mode Operating Regions Frequency Band Description

C819G-4G-ST-K9 • LTE

• EVDO Rev-A

• 1xRTT

C819G-4G-VZ-K9

• LTE

• EVDO Rev-A

• 1xRTT

North America (Sprint)

North America (Verizon)

LTE:

• AWS (band 4)

• 700 MHz (band 13)

• PCS 1900 MHz (band 25)

3G:

• 800 MHz (band class 0)

• 1900 MHz (band class 1)

• 800 MHz (band class 10)

2G:

• 800 MHz (band class 0)

• 1900 MHz (band class 1)

• 800 MHz (band class 10)

LTE:

• AWS (band 4)

• 700 MHz (band 13)

• PCS 1900 MHz (band 25)

3G:

• 800 MHz (band class 0)

• 1900 MHz (band class 1)

• 800 MHz (band class 10)

Non-hardened Cisco 819 router with multi-mode LTE feature for Sprint wireless networks. This comes with a Sierra Wireless MC7350 modem.

Non-hardened Cisco 819 router with multi-mode LTE feature for Verizon wireless networks. This comes with a Sierra Wireless MC7350 modem.

Cisco 810 Series

Re-branding of C8xx-B and EHWIC-3G-EVDO-B

The C881G-B-K9, C819G-B-K9, and EHWIC-EVDO-B (Bharat) SKUs are introduced as an umbrella SKU to cover BSNL, Tata, and Reliance service providers in India.

Software based mechanism is introduced to identify specific carrier. Carrier ID and name are displayed under "show cellular <unit> hardware". The software mechanism is backward compatible with other existing CDMA SKUs such as

HWIC-3G-CDMA(-S,-V) and PCEX-3G-CDMA(-S,-V).

Cisco IOS Requirement

15.3(2)T , 15.3(3)M or l ater. New MIB objects for carrier ID and name will be introduced in later release.

Sample CLI Output

Router#show cellular 0/0/0 hardware

2G:

• 800 MHz (band class 0)

• 1900 MHz (band class 1)

• 800 MHz (band class 10)

Cisco Integrated Services Router Hardware Installation Guide

1-19

Cisco 810 Series

Modem Firmware Version = p2813301 Modem Firmware built = 06-24-10 Hardware Version = MC5728V Rev 1.0 Electronic Serial Number (ESN) = 0x60E62C87 [09615084679] Preferred Roaming List (PRL) Version = 10 PRI SKU ID = 535479 Carrier ID = 19 Carrier Name = Reliance Current Modem Temperature = 30 degrees Celsius Endpoint Port Map = 75 Router#

Router#show cellular 0/1/0 hardware Modem Firmware Version = p2813301 Modem Firmware built = 06-24-10 Hardware Version = MC5728V Rev 1.0 Electronic Serial Number (ESN) = 0x60E62431 [09615082545] Preferred Roaming List (PRL) Version = 10 PRI SKU ID = 535479 Carrier ID = 29 Carrier Name = Tata Current Modem Temperature = 30 degrees Celsius Endpoint Port Map = 75 Router#

Hardware Features

This section provides an overview of the following hardware features for the Cisco 819 ISR.

Chapter 1 Product Overview

• Platform Features for Cisco 819 ISRs, page 1-20

• Antennas, page 1-22

• Power Switch, page 1-22

• Reset Button, page 1-23

• LEDs, page 1-23

• Memory, page 1-27

• Embedded 3G Modem, page 1-27

• Embedded 4G LTE Modem, page 1-27

• SIM Card, page 1-27

• Supported Cisco Antennas and Cables, page 1-28

• Serial Port, page 1-33

• Power Supply, page 1-34

• Accessories, page 1-35

Note The WAAS Express feature is not supported. This feature will be supported for 3G and 4G interfaces

with later IOS releases.

Platform Features for Cisco 819 ISRs

Table 1-7 lists the platform features comparison for the Cisco 819 ISRs.

Cisco Integrated Services Router Hardware Installation Guide

1-20

Chapter 1 Product Overview

Table 1-7 Cisco 819 ISRs Platform Features

Cisco 810 Series

Cisco 819HG-4G Cisco 819G-4G

(with 4G LTE)

Platform Features

Cisco 819HG Cisco 819G

(with 3G)

Cisco 819HGW Cisco 819HWD

(with WiFi)

512 MB DRAM Yes — — 1 GB DRAM — Yes Yes 1 Gigabit Ethernet

Yes Yes Yes

WAN port 12-in-1 serial

Yes Yes Yes

interface 256 KB of NVRAM

Yes Yes Yes

storage 256 Compact Flash

Yes — — support in IDE mode (internal)

1 GB Compact Flash

—YesYes support in IDE mode (internal)

Cisco EnergyWise Yes Yes — Dual 802.11 a/b/g/n

—Yes— Radios with Cisco DFS, CleanAir, and Client Link support

Embedded 3G

Yes Yes — modem

Embedded 4G LTE

——Yes modem

Environmental

Yes Yes — monitoring and temperature logging

Four por ts F E

Yes Yes Yes interconnect switch support

LED indicators for

Yes Yes Yes the platform

Onboard crypto

Yes Yes Yes acceleration

Power cord retention

—YesYes lock

Power switch lock — Yes Cisco 819HG-4G ISRs only Reset button Yes Yes Yes

Cisco Integrated Services Router Hardware Installation Guide

1-21

Cisco 810 Series

Table 1-7 Cisco 819 ISRs Platform Features (continued)

Chapter 1 Product Overview

Platform Features

Real Time Clock

(RTC)

Cisco 819HG Cisco 819G

(with 3G)

Yes Yes Yes

Cisco 819HGW Cisco 819HWD

(with WiFi)

Cisco 819HG-4G Cisco 819G-4G

(with 4G LTE)

ScanSafe Yes Yes — Single console/AUX

Yes Yes Yes

port SNMP Yes Yes — TFTP support with

—Yes— Ethernet WAN interface

Wa rm rel oad Ye s Yes —

1. A real-time clock (RTC) with battery backup provides date and time when the system is powered on. The RTC is used to verify the validity of the Certification Authority stored on the router.

Antennas

The Cisco 819 3G routers provide two standard panel-moun t TNC connectors to support t he 3G antenn a and the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power supply from the router.

The Cisco 819 4G routers provide two standard panel-mount TNC connectors on the router front panel for the main and dive rsity antennas. The main antenna connector is used for the primary 4G antenna. The second antenna connector can be used as a diversity receive only 4G antenna. An SMA connector for active GPS antenna is also available on the front panel of the router.

Power Switch

1-22

The Cisco 819HGW and Cisco 819HWD ISRs also support Cisco WiFi external antennas. See the

“Supported Cisco Antennas and Cables” section on page 1-28 for more information.

WiFi External Antenna

The external WiFi antenna is used to support better WiFi coverage. All external antenna supports the following:

• Dual 802.11 a/b/g/n radios

• 2x3 MIMO

• Omnidirectional

The power switch shuts down the router. A power switch lock is available to prevent accidental turning off of the router in the hardened SKUs.

Cisco Integrated Services Router Hardware Installation Guide

Chapter 1 Product Overview

Reset Button

LEDs

Cisco 810 Series

The Reset button resets the router conf iguration to the defaul t configurati on set by the factory. To restore the router configuration to the default configuration set by the factory, use a standard size #1 paper clip with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power to the router.

The LEDs are located on the front panel of the router. Table 1-8 describes the 3G LEDs for the Cisco 819 ISR.

Table 1-8 3G LED Descriptions

LED Color Description

SYS Yellow FPGA download is complete.

Green (blinking) ROMMON is operational. Green (solid) IOS is operational. Green (four blinks

during bootup) Off After powering up, when FPGA is being downloaded (in

ACT G reen Network activity on FE Switch ports, GE WAN port, 3G

Off No network activity.

WWAN Green Module is powered on and co nnected but no t transmitting

Green (slow blinking) Module is powered on and searching for connection. Green (fast blinking) Module is transmitting or receiving. Off Module is not powered.

GPS Green (solid) Standalone GPS.

Green (slow blinking) GPS is acquiring. Yellow (solid) Assisted GPS. Yellow (slow blinking) Assisted GPS is acquiring. Off GPS is not configured.

Reset button has been pushed during the bootup.

ROMMON).

cellular interface, and serial interfaces.

or receiving.

Cisco Integrated Services Router Hardware Installation Guide

1-23

Cisco 810 Series

Chapter 1 Product Overview

Table 1-8 3G LED Descriptions (continued)

LED Color Description

RSSI Green (solid) Signal > –60 dBm

Very strong signal

Green (three blinks and then a long pause)

Green (two blinks and then a long pause)

Green (one blink and then a long pause)

Off Signal <= –110 dBm

1,2

SIM

Green / Yellow (one green blink followed by two yellow blinks)

Yellow / Green (one yellow blink followed by two green blinks)

Off / Green (two green blinks and then a pause)

Green / Off (Slow sing le green blink and then a pause

Off / Off No SIM present in either slots.

3G Green (one blink and

then a pause) Green (two blinks and

then a pause) Green (three blinks and

then a pause) Green (solid) For HSPA PLUS. Off No Service.

1. Not applicable to Verizon and Sprint EVDO modems.

2. There is only one LED to indicate the status of two SIMs. A one-blink pattern represents the status of the SIM in slot 0, followed by a two-blink pattern for the SIM in slot 1.

Signal <= –60 to 74 dBm Strong signal Signal <= –75 to –89 dBm Fair sign a Signal <= –90 to –109 dBm Marginal signal

Unusable signal SIM in slot 0 active, SIM in slot 1 is not.

SIM in slot 1 active, SIM in slot 0 is not.

No SIM in slot 0, SIM present in slot 1.

SIM present in slot0, no SIM in slot 1.

For 1xRTT, EGPRS, or GPRS service.

For EVDO, EVDO/1xRTT, or UMTS.

For EVDO/1xRTT RevA, HSPA, or HSUPA/HSDPA.

Table 1-9 describes the WLAN LEDs for the Cisco 819HGW and Cisco 819HWD ISRs.

Cisco Integrated Services Router Hardware Installation Guide

1-24

Chapter 1 Product Overview

Table 1-9 WLAN LED Descriptions

WLAN LED Color Description

Boot loader status sequence

Association status Green Normal operating condition with no

Operating status Blinking Blue Software upgrade in progress.

Boot loader errors Blinking Red and Blue FLASH file system failure.

Cisco IOS errors Red Software failure. Try to disconnect and

Cisco 810 Series

Blinking Green Board in itializa tion in p rogress.

Initializing FLASH file system. Initializing Ethernet. Ethernet is OK. Starting Cisco IOS. Initialization is successful.

wireless client associated.

Blue Normal operating condition with at least

one wireless client associated.

Rapidly cycling through Blue, Green, Red, and White

Blinking Red Ethernet link is not operational.

Blinking Red and Off Environment variable failure.

Access point location command invoked.

Bad MAC address. Ethernet failure during the image recovery. Boot environment failure. No Cisco image file. Boot failure.

reconnect the unit power.

Table 1-10 describes the 4G LTE LEDs for the Cisco 819 ISR.

Table 1-10 4G LTE LED Descriptions

LED Color Description

SYS Yellow FPGA download is complete.

Green (blinking) ROMMON is operational. Green (solid) IOS is operational. Green (four blinks

Reset button has been pushed during the bootup.

during bootup) Off After powering up, when FPGA is being do wnloaded (in

ROMMON).

Cisco Integrated Services Router Hardware Installation Guide

1-25

Cisco 810 Series

Chapter 1 Product Overview

Table 1-10 4G LTE LED Descriptions (continued)

LED Color Description

ACT Green Network activity on FE Switch ports, GE WAN port, 3G

cellular interface, and serial interfaces.

Off No network connectivity.

WWAN Green Module is powered on and connected but not

transmitting or receiving. Green (slow blinking) Module is powered on and searching for connection. Green (fast blinking) Module is transmitting or receiving. Off Module is not powered.

GPS Green (solid) Standalone GPS.

Green (slow blinking) GPS is acquiring. Yellow (solid Assisted GPS. Yellow (slow blinking) Assisted GPS is acquiring. Off GPS is not configured.

RSSI Green (solid) Signal > –60 dBm

Green (three blinks and then a long pause)

Green (two blinks and then a long pause)

Green (one blink and then a long pause)

Off Signal <= –110 dBm

SIM Green / Yellow (one

green blink followed by two yellow blinks)

Yellow / Green (one yellow blink followed by two green blinks)

Off / Green (two green blinks and then a pause)

Green / Off (Slo w single green blink and then a pause)

Off / Off No SIM present in either slots.

Very strong signal

Signal <= –60 to 74 dBm

Strong signal

Signal <= –75 to –89 dBm

Fair s i gn a l

Signal <= –90 to –109 dBm

Marginal signal

Unusable signal

SIM in slot 0 is active, SIM in slot 1 is not.

SIM in slot 1 is active, SIM in slot 0 is not.

No SIM in slot 0, SIM present in slot 1.

SIM present in slot 0, no SIM in slot 1.

Cisco Integrated Services Router Hardware Installation Guide

1-26

Chapter 1 Product Overview

Memory

Cisco 810 Series

Table 1-10 4G LTE LED Descriptions (continued)

LED Color Description

3G/4G Green (one blink and

then a pause) Green (two blinks and

then a pause) Green (three blinks and

then a pause) Green (four blinks and

then a pause) Green (Solid) For 4G/LTE service. Off No Service.

The Cisco 819HG and Cisco 819G ISRs uses non-upgradable flash memory and main memory. The onboard flash memory contains the Cisco IOS software image and the boot flash co ntains the ROMMON boot code. Table 1-11 lists the memory requirements for Cisco 819 ISRs.

For 1xRTT, EGPRS, or GPRS service.

For EVDO, EVDO/1xRTT, or UMTS service.

For EVDO/1xRTT RevA, HSPA, or HSUPA/HSDPA service.

For HSPA+ service.

Table 1-11 Memory Requirements for Cisco 819 ISRs

Memory Requirements

256 Compact Flash support in IDE mode (internal)

1 GB Compact Flash support in IDE mode (internal)

512 MB DRAM Yes — — 1 GB DRAM — Yes Yes

Embedded 3G Modem

The 3G cellular interface is the primary WAN data link, but it can also be used as a backup data link. The 3G technology is third-generation wide-area cellular technolog y that is used in broadband wireless data in a mobile environment.

Embedded 4G LTE Modem

The Cisco 819HG-4G and Cisco 819G-4G routers have an embedded 4G L TE modem provided by Sierra Wireless. The Verizon SKUs come with an MC7750 modem, the AT&T SKUs come with an MC7700 modem, and the Global SKUs come with an MC7710 modem.

Cisco 819HG Cisco 819G

(with 3G)

Cisco 819HGW Cisco 819HWD

(with WiFi)

Cisco 819HG-4G Cisco 819G-4G

(with 4G LTE)

Yes — —

—YesYes

SIM Card

Table 1-12 lists the SIM Card slots available for Cisco the 819 ISRs.

Cisco Integrated Services Router Hardware Installation Guide

1-27

Cisco 810 Series

Table 1-12 SIM Card Slot

T wo Internal SIM Card Slots One Internal SIM Card Slot No SIM Card Slot

C819G-U-K9 C819HG-4G-V-K9 C819HG-V-K9 C819G+7-K9 C819G-4G-V-K9 C819HG-S-K9 C819HG-U-K9 C819HG-4G-A-K9 C819G-V-K9 C819HG+7-K9 C819G-4G-A-K9 C819G-S-K9 C819HGW+7-A-A-K9 C819HGW-V-A-K9 C819HGW+7-E-K9 C819HGW-S-A-K9 C819HGW+7-N-K9 C819HG-B-K9 C819HG-4G-G-K9 C819G-B-K9 C819G-4G-G-K9

Supported Cisco Antennas and Cables

Chapter 1 Product Overview

The Cisco 819 ISR provides two standard panel-mount TNC connectors to support the 3G antenna and the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power supply from the router.

Table 1-13 lists the Cisco 3G antennas that are supported for use on Cisco 819 ISRs.

Table 1-13 Supported Cisco 3G Antennas

Maximum Gain and

Cisco Part Number Antenna Type

3G-ANTM1919D Dipole

omnidirectional

Frequency Range Description

0 dBi (806–960 MHz)

0 dBi (1710–2170 MHz)

3G-ANTM1916-CM High-gain

ceiling-mount omnidirectional

1.5 dBi (806–960 MHz)

2.5 dBi (1710–2170 MHz)

3G-AE015-R

Extension base 0.8–6.0 GHz This antenna extension is a base with a 15-foot cable

(Antenna Extension)

3G-ANTM-OUT-OM Outdoor

Omnidirectional

+2 dBi 800/900 MHz

+4 dBi 1800/1900/2100 MHz

This is the default antenna with dual faceplate mount. Multiband faceplate-mounted dipole antenna. For more information, see Cisco Multiband Swivel Mount Dipole

Antenna (3G-ANTM1919D).

Multiband ceiling-mounted omnidirectional antenna. For more information, see Cisco Multiband

Omnidirectional Ceiling Mount Antenna (3G-ANTM1916-CM).

included for use with a dipole omnidirectional antenna. For more information, see Cisco Single-Port Antenna

Stand for Multiband TNC Male-Terminated Portable Antenna (3G-AE015-R).

This is an outdoor low-profile omindirectional mast antenna. For more information, see Cisco 3G

Omnidirectional Outdoor Antenna (3G-ANTM-OUT-OM).

Cisco Integrated Services Router Hardware Installation Guide

1-28

Chapter 1 Product Overview

Table 1-13 Supported Cisco 3G Antennas (continued)

Maximum Gain and

Cisco Part Number Antenna Type

3G-ANTM-OUT-LP Low Profile Stick

Antenna

Frequency Range Description

–1.5 dBi 850, 900 MHz

–2.5 dBi 1800, 1900, 2100 MHz

3G-ACC-OUT-LA

Lightning Arrestor 800–2200 MHz This is a quarter-wave lightning protector with

(Lightning Arrestor)

Cisco 810 Series

This is an omindirectional stick antenna. For more information, see Cisco 3G Low Profile Outdoor Antenna

(3G-ANTM-OUT-LP).

integrated high-pass filter. For more information, see

Cisco 3G Lightning Arrestor (3G-ACC-OUT-LA).

Cisco Integrated Services Router Hardware Installation Guide

1-29

Cisco 810 Series

Table 1-14 lists the supported Cisco WiFi antenna for Cisco 819HGW and Cisco 819HWD ISRs.

Table 1-14 Supported Cisco WiFi Antenna

Chapter 1 Product Overview

Frequency

Antenna

band(s)

AIR-ANTM2050D-R 2.4–2.5 GHz

4.9–5.9 GHz

Mounting Mechanical IP Rating

Faceplate

IP 41 1.4 4.5 This is the default antenna. For

Dipole

Peak Gain

2.4 GHz (dBi)

Peak Gain 5 GHz (dBi) Description

more information, see Cisco

Multiband Swivel-Mount Dipole Antenna (AIR-ANTM2050D-R).

AIR-ANT2430V-R 2.4 GHz Ceiling IP 41 3 — For more information, see

Cisco Aironet 3-dBi Omnidirectional Antenna (AIR-ANT2430V-R).

AIR-ANT5140V-R 5 GHz Ceiling IP 41 — 4 For more information, see

Cisco Aironet 4-dBi Omnidirectional Antenna (AIR-ANT5140V-R).

AIR-ANT2440NV-R 2.4 GHz Multi-mount

(Wall/Ceiling /Mast)

IP 54 4 — For more information, see

Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R).

AIR-ANT5140NV-R 5 GHz Multi-mount

(Wall/Ceiling /Mast)

IP 54 — 4 For more information, see

Cisco Aironet 5-GHz MIMO Wall Mount Omnidirectional Antenna (AIR-ANT5140NV-R).

Cisco Integrated Services Router Hardware Installation Guide

1-30

Chapter 1 Product Overview

Table 1-15 lists the Cisco 4G LTE antennas that are supported for use on Cisco 819 ISRs.

Table 1-15 Supported 4G LTE Antennas

Cisco Part Number Description

4G-LTE-ANTM-D Indoor 4G dipole

omnidirectional antenna

4G-ANTM-OM-CM Indoor ceiling-mount

omnidirectional antenna

ANT-4G-OMNI-OUT-N Multiband outdoor

omnidirectional stick antenna

Cisco 810 Series

Maximum Gain and Frequency Ranges Description

• 2 dBi

–

698 to 806 MHz

–

824 to 894 MHz

–

925 to 960 MHz

–

1710 to 1885 MHz

–

1920 to 1980 MHz

–

2110 to 2170 MHz

–

2500 to 2690 MHz

698 to 2690 MHz Multiband omnidirectional

• 1.5 dBi

–

698 to 960 MHz

• 3.5 dBi

–

1710 to 2710 MHz

Multiband dipole antenna. For more information, see Cisco 4G/3G

Omnidirectional Dipole Antenna (4G-LTE-ANTM-D).

ceiling-mount antenna. For more information, see Cisco 4G Indoor

Ceiling-Mount Omnidirectional Antenna (4G-ANTM-OM-CM).

Multiband outdoor omnidirectional stick antenna. For more information, see Cisco Outdoor Omnidirectional

Antenna for 2G/3G/4G Cellular (ANT-4G-OMNI-OUT-N).

–

2300 to 2700 MHz

ANT-4G-SR-OUT-TNC Multiband outdoor

omnidirectional saucer antenna

• 1.5 dBi (peak gain with

10-foot cable) or 0.8 dBi (peak gain with 15-foot cable)

–

698 to 960 MHz

• 3.7 dBi (peak gain with

Low-profile outdoor saucer antenna. For more information, see Cisco

Integrated 4G Low-Profile Outdoor Saucer Antenna (ANT-4G-SR-OUT-TNC).

10-foot cable) or 0.2 dBi (peak gain with 15-foot cable)

–

1710 to 2700 MHz

CGR-LA-NF-NF Lighning Arrestor 800 to 2200 MHz 4G lightning arrestor kit for use on

Cisco 4G wireless devices. For more information, see Lightning Arrestor for

the Cisco 1240 Connected Grid Router.

4G-ACC-OUT-LA Lightning Arrestor 800 to 2200 MHz 4G lightning arrestor kit for use on

Cisco 4G wireless devices. For more information, see Cisco 4G Lightning

Arrestor (4G-ACC-OUT-LA).

Cisco Integrated Services Router Hardware Installation Guide

1-31

Cisco 810 Series

Chapter 1 Product Overview

Table 1-16 to Table 1-18 list the extension cables for use with 3G, WiFi, and 4G LTE antennas. The

tables include the insertion loss information for the ultra-low-loss (ULL) LMR 400 extension cables.

Table 1-16 Cisco Extension Cables for Use with 3G Antennas

Cisco Product Number Cable Length Insertion Loss Frequency (MHz)

3G-CAB-ULL-20 20 ft (6 m) 1.50 dB max 2100 3G-CAB-ULL-50 50 ft (15 m) 3.50 dB max 2100 3G-CAB-LMR240-25 25 ft (7.5 m) 3.50 dB max 2200 3G-CAB-LMR240-50 50 ft (15 m) 6.90 dB max 2200 3G-CAB-LMR240-75 75 ft (23 m) 10.5 dB max 2200

Table 1-17 Cisco Extension Cables for Use with WiFi Antennas

Cisco Product Number Cable Length Insertion Loss Frequency (MHz)

AIR-CAB005LL-R 5 ft (1.524 m)

0.5 dB

2400

(one RP-TNC plug, one RP-TNC jack)

AIR-CAB020LL-R 20 ft (6 m)

(one RP-TNC plug, one RP-TNC jack)

AIR-CAB050LL-R 50 ft (15.24 m)

(one RP-TNC plug, one RP-TNC jack)

Table 1-18 Cisco Extension Cables for Use with 4G LTE Antennas

Maximum Insertion

Cisco Product Number Cable Length

4G-AE010-R 10 ft (3 m) 1.4 dB at 700 MHz

Loss Frequency (MHz) Color Plenum Rated?

700 to 2600 MHz Black No

2.0 dB at 1.9 GHz

2.1 dB at 2.1 GHz

2.3 dB at 2.5 GHz

4G-AE015-R 15 ft (4.6 m) 2.3 dB at 700 MHz

700 to 2600 MHz Black No

3.3 dB at 1.9 GHz

0.8 dB

1.3 dB

2.5 dB

3.4 dB

5.75 dB

5800

2400 5800

4G-CAB-LMR240-25 25 ft (7.6 m) 2.1 dB at 700 MHz

Cisco Integrated Services Router Hardware Installation Guide

1-32

3.7 dB at 2.1 GHz

4.0 dB at 2.5 GHz

4.0 dB at 2.6 GHz

700 to 1000 MHz 1700 to 2600 MHz

Black Yes

Chapter 1 Product Overview

Table 1-18 Cisco Extension Cables for Use with 4G LTE Antennas (continued)

Cisco 810 Series

Maximum Insertion

Cisco Product Number Cable Length

4G-CAB-LMR240-50 50 ft (15 m) 4.1 dB at 700 MHz

4G-CAB-LMR240-75 75 ft (23 m) 6.1 dB at 700 MHz

4G-CAB-LMR240-25N 25 ft (7.6 m) 2.1 dB at 700 MHz

Loss Frequency (MHz) Color Plenum Rated?

7.4 dB at 2.6 GHz

11.0 dB at 2.6 GHz

4.0 dB at 2600 MHz

700 to 1000 MHz 1700 to 2600 MHz 700 to 1000 MHz 1700 to 2600 MHz 700 to 1000 MHz 1700 to 2600 MHz

Black Yes

Black No

4G-CAB-ULL-20 20 ft (6 m) 1.8 dB 700 to 2600 MHz Black Yes 4G-CAB-ULL-50 50 ft (15 m) 4.2 dB 700 to 2600 MHz Black Yes CAB-L400-20-TNC-N 20 ft (6 m) 1.75 dB 700 to 2600 MHz Black No CAB-L400-50-TNC-N 50 ft (15 m) 4.0 dB 700 to 2600 MHz Black No CAB-L400-20-N-N 20 ft (6 m) 2.75 dB 700 to 2600 MHz Black No

1. Cable can be routed within building plenum spaces.

Serial Port

The Cisco standard High Speed Smart Serial 12-in-1 connector allows the highest flexibility of connections to various DTE/DCE devices. The 12-in-1 serial interface pins connect to the FPGA. The FPGA configures the pin directions based on the cable t ype used. Figure 1-10 shows the magnified view of the 12-in-1 serial port. For more information, see About Serial Connections.

Cisco Integrated Services Router Hardware Installation Guide

1-33

Cisco 810 Series

Chapter 1 Product Overview

Figure 1-10 12-in-1 Serial P ort

Power Supply

344749

All SKUs require a 5 VDC po wer sourc e. Cisco 819HG and Cisco 819G ISRs h av e a self-locking Molex mini-fit connector. Cisco 819HGW and Cisco 819HWD ISRs use a 5.5 mm barrel-type connector with separate locking clip. An external A C power adapter is supported by default. The optional external power adapters are available to support a variety of DC power sources, suitable for fixed, vehicle, or railway installations. The 5 VDC power input of the router is protected from over-voltage up to 20 VDC. The router will not power up if excessive voltage (for example, a 12 VDC adapter) is connected.

AC Power Adapter

The default configuration includes an external AC adapter that supplies up to 20 W of power. The AC power connection is a two-pin IEC 320 C8 receptacle. A mating AC power cord is supplied. The AC adapter does not provide chassis grounding to the router. A 1.3-meter long output cable connects to the router.

DC Power Adapters

The optional external DC power adapters are available for 12 VDC and 24 VDC nominal vehicle power.

• 12 VDC vehicle adapter has a 10 VDC to 36 VDC operating range

• 24 VDC vehicle adapter has an 18 VDC to 75 VDC operating range

Cisco Integrated Services Router Hardware Installation Guide

1-34

Chapter 1 Product Overview

Note The 24 VDC vehicle adapters will be available on Q1CY13.

Accessories

Cisco 860, 880, 890 Series

The vehicle power adapters may be used for fixed or mobile installat ions. The y do not p rovi de electrical isolation; the input negative is connected to the output negative (chassis ground). Input cable is 350 millimeter long with stripped and tinned b are wire connections. The input positi ve co nnection is a white wire and the input negative is a black wire.

Railway Power Adapters

The optional external power adapters meeting Railway Standards are available from a third-party supplier, Martek Power. Contact Martek Power directly to order and for detai led specif ications. The use of Martek Power adapters listed in the “Supported Power Adapters” section on page A-9 will maintain Cisco warranty and support of the router; the power adapter itself is covered by Martek warranty. Input connection to the railway adapters is by a 350 millimeter long wire with stripped and tinned bare wire connection. A 1.3-meter long output cable connects to the router.

Table 1-19 lists the accessories available for the Cisco 819 ISRs. For a complete list of SKUs that support

these accessories, see the “Platform Features for Cisco 819 ISRs” section on page 1-20.

Table 1-19 Cisco 819 ISR Accessories

Cisco Part Number Accessory

69-2453-01 Power cord retention lock 69-2454-01 Power switch lock cover

Cisco 860, 880, 890 Series

This section provides an overview of the features available for the Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections:

• General Description, page 1-36

• Cisco 860 Series ISRs, page 1-36

• Cisco 860VAE Series ISRs, page 1-38

• Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs,

page 1-40

• Cisco 880 Series ISRs, page 1-44

• Cisco C881, C886, and C887 Series ISRs, page 1-57

• Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers, page 1-67

• Cisco 890 Series Integrated Service Routers, page 1-97

• Cisco C891 Series ISRs, page 1-110

• Hardware Features, page 1-115

Cisco Integrated Services Router Hardware Installation Guide

1-35

Cisco 860, 880, 890 Series

Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap

that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series.

Note Some illustrations in this document show a wireless router. Both wireless and nonwireless models are

available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations are similar for both wireless and nonwireless routers.

Note Throughout this document the term VDSL refers to support for VDSL2 (ITU G.993.2) and ADSL refers

to support for ADSL, ADSL2, & ADSL2+ (ITU G.992.1, G.992.3, & G.992.5).

General Description

The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs provide data, voice, Wi-Fi CERTIFIED™ wireless access point (AP), integrated Virtual Private Network (VPN), and backup capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users. These routers are capable of bridging and multiprotocol routing between LAN and WAN ports. The routers provide advanced features, such as high speed DSL (G.SHDSL, ADSL, or VDSL), 802.11n, quality of service (QoS), firewall , antivirus protection, and Secure Sock et Layer (SSL). The Cisco 860VAE, 886V A and 887VA series routers have the additional capabil ity of DSL Multi -mode (VDSL/AD SL).

Chapter 1 Product Overview

The Cisco 860 series, Cisco 880 series, and Cisco 8 90 series ISRs have a desktop form factor with built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These ISRs are powered by an external power supply adapter. The various models differ in the WAN interface and features that they support.

Cisco 860 Series ISRs

The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:

• An integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• A10/100 Fast Ethernet (FE) port for connecting to the WAN.

• Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP

Cisco Integrated Services Router Hardware Installation Guide

1-36

Chapter 1 Product Overview

232181

31 4 6 7 852

WAN

FE 4

Cisco 861W

Figure 1-7 shows the front panel details of the Cisco 860 wireless router.

Figure 1-11 Front Panel of the Cisco 860 Series Wireless ISR

Cisco 860, 880, 890 Series

231969

1 LEDs

Figure 1-12 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do

not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series routers.

Figure 1-12 Back Panel of the Cisco 861W ISR

1 Primary WAN port—10/100 5 Reset button 2 Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

3 4-port 10/100 Ethernet switch 7 Earth ground connection 4 Serial port—console or auxiliary 8 Kensington security slot

6 Power connector

Cisco Integrated Services Router Hardware Installation Guide

1-37

Cisco 860, 880, 890 Series

Cisco 860VAE Series ISRs

The Cisco 860VAE series ISRs are fixed-configuration data routers. This section describes the features of the products in this series.

Interfaces

Table 1-20 describes the interfaces of the Cisco 860VAE series routers.

Table 1-20 Interfaces of the Cisco 860VAE Series ISRs

Interfaces

4 FE

switch ports

1 GE

switch port 1 GE WAN port xxxx 1 VDSL/ADSL over POTS port — x — x 1 VDSL/ADSL over ISDN port x — x —

1. FE = Fast Ethernet

2. GE = Gigabit Ethernet

Chapter 1 Product Overview

Model

866VAE 867VAE 866VAE-K9 867VAE-K9

xxxx

—— x x

IOS Images

Note The Cisco 866VAE, 867V AE, 866 VAE-K9, and 867V AE-K 9 routers each hav e two WAN ports. Only one

of the two ports can be active at any given time.

Table 1-21 describes the IOS images included in Cisco 860VAE series routers.

Table 1-21 IOS Images of the Cisco 860VAE Series ISRs

Model

IOS Image

866VAE 867VAE 866VAE-K9 867VAE-K9

c860vae-ipbasek9-mz x x — — c860vae-advsecurityk9-mz — — x x c860vae-advsecurityk9_npe-mz — — x x

Cisco Integrated Services Router Hardware Installation Guide

1-38

Chapter 1 Product Overview

246199

Cisco 860 Series

246200

CONSOLE

AUX

FE 2 FE 1 FE 0FE 3OVER ISDN

LAN

WAN

GE0

VDSL/ADSL

12V 2.5A

RESET

Cisco 866VAE

1 2 3 4 7 8 95 6

Figure 1-13 shows the front panel details of the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and

Cisco 867VAE-K9 integrated services routers (ISRs).

Figure 1-13 Front Panel of the Cisco 860VAE series ISR

1 LEDs

Figure 1-14 shows the back panel details of the Cisco 866VAE ISR.

Cisco 860, 880, 890 Series

Figure 1-14 Back Panel of the Cisco 866VAE ISR

1 xDSL port

6 On/Off switch 2 GE WAN interface 7 Power connector 3 Ethernet LAN FE interfaces (FE0 through

8 Reset button

FE3 interfaces)

4 USB port 9 Kensington security slot 5 Serial port—console or auxiliary

1. Using RJ-11.

Cisco Integrated Services Router Hardware Installation Guide

1-39

Cisco 860, 880, 890 Series

284558

CONSOLE

AUX

OVER POTS

WAN LAN

GE1 GE0 FE3 FE2 FE1 FE0

VDSL/ADSL

12V 2.5A

RESET

Cisco 867VAE-K9

1 2 3 4 7 8 95 6

Figure 1-15 shows the back panel details of the Cisco 867VAE-K9.

Figure 1-15 Back Panel of the Cisco 867VAE-K9 ISR

Chapter 1 Product Overview

1 xDSL port 6 On/Off switch 2 GE WAN interface 7 Power connector 3 Ethernet LAN GE and FE interfaces (GE0

interface and FE0 through FE3 interfaces)

4 USB port 9 Kensington security slot 5 Serial port—console or auxiliary

8 Reset button

Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs

This section provides a hardware overview of the following Cisco 860VAE Series Integrated Services Routers (ISRs):

• C866VAE-W-E-K9

• C867VAE-W-A-K9

• C867VAE-W-E-K9

• C867VAE-POE-W-A-K9

Model-Specific Features

Table 1-22 describes the features specific to each of these router models:

Table 1-22 Model-Specific Router Feat u res

C866VAE-W-E-K9C867VAE-W-A-K9C867VAE-W-E-K9C867VAE-POE-

Feature

WAN interface and mode One GE port,

DSL over ISDN, Europe WiFi

Power-over-Ethernet (PoE)NoNoNoYes

One GE port, DSL ove r POTS, America WiFi

One GE port, DSL ove r POTS, Europe WiFi

W-A-K9

One GE port, DSL ove r POTS, America WiFi

Cisco Integrated Services Router Hardware Installation Guide

1-40

Chapter 1 Product Overview

VDSL/ADSL

WAN

GE2

LAN

GE1OVER POTS

CONSOLE

12V

RESET

2.5A

AUX

GE0 FE2 FE1

Cisco 867VAE-POE-W-A-K9

FE0(POE)

360426

Common Features

External Interfaces

Cisco 860, 880, 890 Series

The following key features are common to each of these router models:

• Dual WAN interface (Gigabit Ethernet [GE] and dual-mode ADSL2+ /VDSL2)

• 2.4 GHz wireless LAN (WLAN) interface

• Five Layer 2 LAN switches: two Gigabit Ethernet and three Fast Ethernet

• One USB 2.0 port in high-speed host mode

• One RJ-45 console port (RS-232 interface)

• Support for up to 512 MB DRAM using DDR in 16-bit mode

• Support for 8 MB Serial Peripheral Interface Bus (SPI) flash memory for boot and 128 MB NAND

flash memory for storing IOS

• Reset/Recovery switch

• Silent convection cooling—no fan

Figure 1-16 shows the back I/O panel of the Cisco 867VAE-POE-W-A-K9 series router.

Figure 1-16 Back I/O Panel

Table 1-23 describes the external interfaces included with these router models.

Table 1-23 External Interfaces

Port

Interface Connector Quantity Port

Label

FE LAN port RJ-45 3 FE LAN PORT 0 FE0

FE LAN PORT 1 FE1 FE LAN PORT 2 FE2

GE LAN port RJ-45 2 GE LAN PORT 0 GE0

GE LAN PORT 1 GE1 GE WAN port (10/100/1000 Base-T) RJ-45 1 GE WAN PORT GE2 ADSL2+/VDSL2 WAN port RJ-11 1 — — Host USB port USB 2.0 1 — — Console port RJ-45 1 — —

1. Provides Power-over-Ethernet (PoE) for the Cisco C867VAE-POE-W-A-K9.

Cisco Integrated Services Router Hardware Installation Guide

1-41

Cisco 860, 880, 890 Series

Note For the Cisco C867VAE-POE-W-A-K9, Power-over-Ethernet (PoE) is available using port FE0, with a

USB Interface

Note The USB 2.0 port cannot be used for connecting external devices or as a console for devices other than

Chapter 1 Product Overview

60-W power supply.

The USB 2.0 interface enables:

• Transferring data using a USB flash token (USB memory stick) for system recovery and other tasks.

• Cisco IOS software boot from USB.

Use only the following Cisco USB 2.0 flash tokens:

• MEMUSB-128FT (128 MB)

• MEMUSB-256FT (256 MB)

• MEMUSB-1024FT (1 GB)

those specified in the USB eToken Device and USB Flash Features Support Data Sheet, available at:

http://www.cisco.com/en/US/prod/collateral/modules/ps6247/product_data_sheet0900aecd80232473.h tml

LED Indicators

These router models include LED indicators on the back panel for each LAN port, and a dditional LED indicators on the front panel of the unit.

LED Indicators for LAN Ports

On the back panel of the unit, each LAN port includes an LED indicator. Table 1-24 describes the LED indicators.

Table 1-24 Back Panel LED Indicators for LAN Ports

Port LED Color Description

FE Ports

FE LAN 0 Green Off—No link.

Faster flashing indicates heavier traffic.

FE LAN 1 Green Off—No link.

Faster flashing indicates heavier traffic.

FE LAN 2 Green Off—No link.

Faster flashing indicates heavier traffic.

GE Ports

GE LAN 0 Green Off—No link.

Faster flashing indicates heavier traffic.

GE LAN 1 Green Off—No link.

Faster flashing indicates heavier traffic.

Cisco Integrated Services Router Hardware Installation Guide

1-42

Chapter 1 Product Overview

346497

Cisco 860 Series

WLAN

LED Indicators on Front Panel

The front panel includes several LED indicators. Figure 1-17 shows the location of the LED indicators.

Figure 1-17 Front Panel LED Indicators

1 LED indicators

Cisco 860, 880, 890 Series

Cisco Integrated Services Router Hardware Installation Guide

1-43

Cisco 860, 880, 890 Series

Table 1-25 describes the LED indicators.

Table 1-25 Front Panel LED Indicators

Chapter 1 Product Overview

LED LED Color LED Activity Description

Left Side

DSL ACT Green Flashing DSL WAN activity. Faster flashing indicates heavier

traffic.

Off — Device is powered off.

or No DSL WAN activity.

DSL LINK Green Solid DSL W AN mode is selected and DSL training is complete.

Flashing DSL WAN mode is selected but DSL LinkUp state is

incomplete, such as in-training (slow initially, fast when almost connected).

Off — Device is powered off.

or GE WAN mode is selected.

GE ACT Green Flashing GE WAN activity (traffic in either direction). Faster

flashing indicates heavier traffic.

Off — Device is powered off.

GE MODE Green Solid GE WAN mode is selected.

Right Side

WLAN Green Solid WLAN enabled.

Power Green Solid On—The device is powered on.

Cisco 880 Series ISRs

or No GE WAN activity. or No link.

Off — Device is powered off.

or DSL WAN mode is selected.

Flashing Indicates WLAN activity (traffic in either direction).

Off — Device is powered off.

or WLAN is disabled.

Off — Device is powered off.

The Cisco 880 series ISRs have data and voice capabilities. They have the following features:

Cisco Integrated Services Router Hardware Installation Guide

1-44

Chapter 1 Product Overview

• Integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• 10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode

• Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP

• Optional 2-port Power over Ethernet (PoE)

• DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB

The following features are located on the front panel:

• USB 1.1 port

• Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the

This section contains the following topics:

• Cisco 880 Series Data Routers, page 1-45

Cisco 860, 880, 890 Series

(VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for connecting to the WAN

Note The Cisco 880 series ISRs can include an optional PoE module that provides power to

802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the PoE function.

system memory

Cisco 880G models

• Cisco 880 Series Voice and Data Routers, page 1-48

• Cisco 880 Series with Embedded WLAN Antennas, page 1-54

• C881G-B/S/V-K9 ISRs, page 1-56

• C881GW-S/V-A-K9 ISRs, page 1-56

• C881G-U-K9 ISRs, page 1-57

• HSPA+ Versions of the Fixed-Platform ISRs, page 1-57

Cisco 880 Series Data Routers

The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™,

802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. Figure 1-18 through Figure 1-21 show the features available on Cisco 880 series data routers. Some of the features shown may not be a vailable on your router.

Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, VDSL/ADSL over ISDN, VDSL/ADSL over POTS, or 10/100 FE. See the Cisco 880 Series Integrated Services

Routers data sheet for the WAN interface that is supported on your router.

Figure 1-18 shows the front panel details of the Cisco 8 80 wireless data router. The USB port and the

3G card slot are located on the front panel.

Cisco Integrated Services Router Hardware Installation Guide

1-45

Cisco 860, 880, 890 Series

231950

1 2 3

254090

1 3 4 5 7 8 962

Figure 1-18 Front Panel of the Cisco 880 Series Wireless Data Router

1 LEDs 3 USB port 2 3G express card slot—Supports third-party

3G card (Cisco 880G models only)

1. Se e the Cisco 880 Series Integrated Services Routers data sheet for s upported vendo rs.

Chapter 1 Product Overview

Figure 1-19 shows the back panel details of the Cisco 886VA data router.

Figure 1-19 Back Panel of the Cisco 886VA Router

1 Data BRI1 0 6 Reset button 2 Primary WAN port—VDSL/ADSL over

7 Power connector

ISDN

3 4-port 10/100 Ethernet switch

8 Earth ground connection 4 Serial port—console or auxiliary 9 Kensington security slot 5 PoE power connector—optional

1. BRI = Basic rate interface.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may

occur if a non-RJ-45 connector is inserted.

Cisco Integrated Services Router Hardware Installation Guide

1-46

Chapter 1 Product Overview

254139

2 3 4 6 7 851

231951

1 4 5 6 8 9 1072 3

Figure 1-20 shows the back panel details of the Cisco 887VA and 886VA-M data router.

Figure 1-20 Back Panel of the Cisco 887VA and 887VA-M Router

Cisco 860, 880, 890 Series

1 Primary WAN port—VDSL/ADSL over

2 4-port 10/100 Ethernet switch

POTS

5 Reset button

6 Power connector 3 Serial port—console or auxiliary 7 Earth ground connection 4 PoE power connector—optional 8 Kensington security slot

1. 887VA-M has Annex M support.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

For the Cisco 887VA, the primary WAN port is designed for an RJ-11 connector only. Damage to the

primary WAN port may occur if a non-RJ-11 connector is inserted.

Figure 1-21 shows the back panel details of the Cisco 888W data router . Nonwireless rout ers do not ha ve

antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data routers.

Figure 1-21 Back Panel of the Cisco 888W Data Router

Cisco Integrated Services Router Hardware Installation Guide

1-47

Cisco 860, 880, 890 Series

Chapter 1 Product Overview

1 ISDN port—not available on 3G models 6 PoE power connector for optional PoE

2 Primary WAN port2—G.SHDSL,

VDSLoPOTS, ADSLoPOTS, ADSLoISDN, or 10/100 FE

3 Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

4 4-port 10/100 Ethernet switch 9 Earth ground connection 5 Serial port—console or auxiliary 10 Kensington security slot

1. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the PoE function.

2. Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, or 10/100 FE. The VDSLoPOTS port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See

Figure 1-12 for the location of the 10/100 FE WAN port.

Cisco 880 Series Voice and Data Routers

The Cisco 880 series voice and data routers provide both voice and data ports. The voice ports managed voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or BRI connections.

Cisco 881 SRST and Cisco 888 SRST

module

7 Reset button

8 Power connector

Figure 1-22, Figure 1-23, and Figure 1-24 show the features available on the Cisco 881 SRST and

Cisco 888 SRST routers. The features available vary , depend ing on the router model. Some features m ay not be available on your router.

Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE. See the

Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are

supported on your router.

Cisco Integrated Services Router Hardware Installation Guide

1-48

Chapter 1 Product Overview

270495

1 2

Figure 1-22 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice

router.

Figure 1-22 Front Panel of the Cisco 881 SRST and Cisco 888 SRST Wireless Voice Router

Cisco 860, 880, 890 Series

1 LEDs 2 USB port

Cisco Integrated Services Router Hardware Installation Guide

1-49

Cisco 860, 880, 890 Series

241904

31 4 7 98 1022 56

Figure 1-23 shows the back panel details of the Cisco 881SRST-W voice router.

Figure 1-23 Back Panel of the Cisco C881SRST-W Voice Router

Chapter 1 Product Overview

1 Primary WAN port1—10/100 FE

6 Antenna—captive wireless omnidirectional

dipole WLAN antenna (wireless models only)

2 Voice ports—four FXS

FXO

port with TBP5 power fai l over

3 4-port 10/100 Ethernet switch

/DID3 ports, one

7 Reset button

8 Power connector 4 Serial port—console or auxiliary 9 Earth ground connection 5 PoE power connector for optional PoE

module

1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.

2. FXS = Foreign Exchange Station.

3. DID = Direct Inward Dialing.

4. FXO = Foreign Exchange Office.

5. TBP = trunk bypass.

6. Ports 0 and 1 provide PoE with the optional PoE module installed.

7. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and ins tall the Field Replaceable Unit (FRU) to enable the PoE function. For this you either need the FRU “800-IL-PM=2” or “800G2-POE-2”. If your device has a separate PoE inlet, use the 800-IL-PM=2, if it has one combined inlet (a description saying “POE OPTION REQUIRES 5A POWER ADAPTOR”), then use the 800G2-POE-2.

10 Kensington security slot

Cisco Integrated Services Router Hardware Installation Guide

1-50

Chapter 1 Product Overview

241905

32 2 4 7 9 1086 51

Figure 1-24 shows the back panel details of the Cisco 888SRST-W voice router.

Figure 1-24 Back Panel of the Cisco C888SRST-W Voice Router

Cisco 860, 880, 890 Series

1 Primary WAN port

—G.SHDSL

2 Voice ports—four FXS/DIDports and one

voice BRI port

3 4-port 10/100 Ethernet switch 4 Serial port—console or auxiliary 9 Earth ground connection 5 PoE power connector for optional PoE

module

1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

3. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and ins tall the Field Replaceable Unit (FRU) to enable the PoE function. For this you either need the FRU “800-IL-PM=2” or “800G2-POE-2”. If your device has a separate PoE inlet, use the 800-IL-PM=2, if it has one combined inlet (a description saying “POE OPTION REQUIRES 5A POWER ADAPTOR”), then use the 800G2-POE-2.

The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage to the

primary WAN port may occur if a non-RJ-45 connector is inserted.

Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W

Figure 1-25, Figure 1-26, and Figure 1-27 show the features available on the Cisco 8 81-V and

Cisco 887VA-V routers. The features available v ary, depending on the router model. Some features may not be available on your router.

The Cisco 881-V and Cisco 887VA-V voice and data series gives you the flexibility to use either FXS or BRI voice ports. Howe ver , the number of concurrent calls that can be supp orted by the router is limited by the codec complexity setting on the router. Table 1-26 lists the maximum number of calls that is supported when the codec complexity command is configured for Fle xible, Medium or High complexity.

6 Antenna—captive wireless omnidirectional

dipole WLAN antenna (wireless models only)

7 Reset button

8 Power connector

10 Kensington security slot

Cisco Integrated Services Router Hardware Installation Guide

1-51

Cisco 860, 880, 890 Series

Note Configuring the codec comple xity setting t o support secure calls uses DSP resources, but does not af fect

the maximum number of supported calls.

Table 1-26 Maximum Number of Supported Calls

Figure 1-25 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.

Figure 1-25 Front Panel of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W Routers

Chapter 1 Product Overview

Flexible Complexity Medium Complexity High Complexity

C881-V986 C887VA-V886 C887VA-V-W 8 8 6

1-52

246861

1 2

1 LEDs 2 USB port

Cisco Integrated Services Router Hardware Installation Guide

Chapter 1 Product Overview

246864

overPOTS

VDSL/ADSL

C887VA-W VO ICE

1 4 5 6 8 9 107

246866

C881 VO ICE

1 4 5 6 8 9 10732

Figure 1-26 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (non-wireless)

router does not have the antennas on the back panel.

Figure 1-26 Back Panel of the Cisco 887 VA-V Router

Cisco 860, 880, 890 Series

1 Data BRI 7 Reset Button 2 Voice B RI 8 Power connector 3 Voice ports—four FXS/DID ports 9 Earth ground connection 4 Fast Ethernet LAN—four ports 10 Kensington security slot 5 Console Port 11 Primary WAN port—VDSL/ADSL over

POTS

6 PoE power connector (optional)

Figure 1-27 shows the back panel for the Cisco 881-V router.

Figure 1-27 Back Panel of the Cisco 881-V Router

Cisco Integrated Services Router Hardware Installation Guide

1-53

Cisco 860, 880, 890 Series

284983

PPP

WLAN

POE

LINK 2.4GHz 5GHz

Cisco 800 Series

FE LAN

VPN

0123

xDSL

CD DATA

1 Fast Ethernet WAN port 6 PoE power connector (optional) 2 Voice BRI ports 7 Reset button 3 Voice ports—four FXS/DID ports and one

FXO port.

4 Fast Ethernet LAN—four ports 9 Earth ground connection 5 Console Port 10 Kensington security slot

Cisco 880 Series with Embedded WLAN Antennas

Some Cisco 880W, 880WD, and 880-WD ISRs have three embedded WLAN antennas. These ISRs are fixed-platform routers that:

• Provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, and

backup capabilities.

• Use single-band (2.4 GHz) WLAN cards or dual-band (2.4 GHz and 5 GHz) WLAN cards.

• Require a single external power supply: a 30-W power supply for non-POE-enabled routers or a

60-W power supply for POE-enabled routers.

• Have a fixed 512 MB of system memory.

Chapter 1 Product Overview

8 Power connector

Cisco 887VA-WD

For information on configuring the Cisco 880 series ISRs, see Cisco 880 Series Integrated Services

Router Software Configuration Guide.

Figure 1-28 shows the front panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs. The

front panel has LEDs only. All the ports are in the back panel.

Figure 1-28 Front Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

1-54

Cisco Integrated Services Router Hardware Installation Guide

Chapter 1 Product Overview

284988

Cisco 887VA-WD

AUX

CONSOLE

FE LAN

POE OPTION

REQUIRES 5A

POWER

ADAPTOR

3 210

RESET

12VDC 5A

overPOTS

1 2 3 4 5 6 7

284988

Cisco 887VA-WD

AUX

CONSOLE

FE LAN

POE OPTION

REQUIRES 5A

POWER

ADAPTOR

3 210

RESET

12VDC 5A

overPOTS

1 2 3 4 5 6 7

284982

PPP

FE4

WAN

WLAN

POE

LINK 2.4GHz 5GHz

Cisco 800 Series

FE LAN

VPN

0123

Figure 1-29 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.

Figure 1-29 Back Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

1 USB port 6 Power connector 2 4-port 10/100 Ethernet switch 7 Kensington security slot 3 Serial port—console or auxiliary 8 Power switch 4

5 Reset button

Note No separate PoE power supply is

required for routers with embedded WLAN antennas. For information on system power supply requirements when PoE is enabled, see the “Power

over Ethernet Module” section on page 1-126.

Cisco 860, 880, 890 Series

9 VDSL/ADSL port

C881WD

Figure 1-30 shows the front panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. The front

panel has LEDs only. All the ports are in the back panel.

Figure 1-30 Front Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

Cisco Integrated Services Router Hardware Installation Guide

1-55

Cisco 860, 880, 890 Series

284987

Cisco 881WD

AUX

CONSOLE

FE LAN

POE OPTION

REQUIRES 5A

POWER

ADAPTOR

3 210

RESET

12VDC 5A

FE WAN

21 3 4 5 6 7 8

Figure 1-31 shows the back panel details of the C881W D-A-K9 and C8 81WD-E-K9 ISRs.

Figure 1-31 Back Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

Chapter 1 Product Overview

1 Primary WAN port—10/100 FE 6 Reset button 2 USB port 7 Power connector 3 4-port 10/100 Ethernet switch 8 Kensington security slot 4 Serial port—console or auxiliary 9 Power switch 5

Note No separate PoE power supply is

required for routers with embedded WLAN antennas. For information on system power supply requirements when PoE is enabled, see the “Power

over Ethernet Module” section on page 1-126.

C881G-B/S/V-K9 ISRs

C881GW-S/V-A-K9 ISRs

1-56

Cisco Integrated Services Router Hardware Installation Guide

The C881G-B-K9, C881G-S-K9, and C881G-V-K9 ISRs are members of the Cisco 880 series data routers. These routers provide integrated Virtual Private Network (VPN), 802.11b/g/n-compliant wireless Access Point (AP), 3G, and backup capabilities.

For information on configuring Cisco 88 0 Series ISRs, see Cisco 880 Series Integrated Services Router

Software Configuration Guide.

The C881GW-S-A-K9 and C881GW-V-A-K9 ISRs are members of the Cisco 880G series data routers. These routers provide integrat ed VPN, embedded W i-Fi CER TIFIED™, 802.11b/g/n-compliant wireless AP, 3G, and backup capabilities.

For information on configuring Cisco 88 0 Series ISRs, see Cisco 880 Series Integrated Services Router

Software Configuration Guide.

Chapter 1 Product Overview

C881G-U-K9 ISRs

The C881G-U-K9 ISR is a member of the Cisco 880 series data routers. These routers provide integrated Virtual Private Network (VPN), embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless Access Point (AP), 3G, and backup capabilities.

For information on configuring Cisco 88 0 Series ISRs, see Cisco 880 Series Integrated Services Router

Software Configuration Guide.

HSPA+ Versions of the Fixed-Platform ISRs

The C881G+7-K9, C886VAG+7-K9, C887VAG+7-K9, C887VAMG+7-K9, C888EG+7-K9, C881GW+7-A-K9, C881GW+7-E-K9, C887VAGW+7-A-K9, and C887VAGW+7-E-K9 ISRs are members of the Cisco 880G series data routers. These routers provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, 3G, and backup capabilities.

For information on configuring Cisco 88 0 Series ISRs, see Cisco 880 Series Integrated Services Router

Software Configuration Guide.

Cisco 860, 880, 890 Series

Cisco C881, C886, and C887 Series ISRs

Cisco C881, C886, and C887 Series ISRs offer broadband speed and simplified management to small businesses, small enterprise branches, and teleworkers. The Cisco C881, C886, and C887 Series ISR models have a lead-free, fanless chassis and are updated versions of the previous Cisco 881, 886, and 887 series (excluding 3G and wireless models).

Information provided in this section is applicable for the following models:

• Cisco C881

• Cisco C886VA, Cisco C886VAJ (Annex J)

• Cisco C887VA, Cisco C887VAM (Annex M)

Table 1-27 provides information about important hardware specifications pertaining to Cisco C881,

C886, and C887 Series Routers.

Table 1-27 Hardware Specifications of Cisco C881, C886, and C887 Series

Routers

Hardware Description

Flash Memory 256 MB Main Memory 1 GB DDR RAM; fixed and not extendable USB port A USB 2.0-compliant port located at the back

FAN Fanless chassis PoE Two internal PoE ports WAN

panel

• C881— FE

• C886—VDSL/ADSL over ISDN with ISDN

back up

• C887—VDSL/ADSL over POTS

Cisco Integrated Services Router Hardware Installation Guide

1-57

Cisco 860, 880, 890 Series

CiscoCisco

800

Series

OKOK

POEOE

PPPPPP

FEFE4

WAN

0 1

VPN

0 1 2

FE LAN

361124

Cisco C881 Router

Chapter 1 Product Overview

Hardware Description

Console or auxiliary port RJ-45 LAN switch 4-port 10/100BASE-T

For detailed hardware specifications, see t he Cisco 880 Series hardware data sheet at:

http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_ Data_Sheet.html

Figure 1-32 shows the front panel of the Cisco C881 Router.

Figure 1-32 Front Panel of the Cisco C881 Router

1 LEDs

For detailed description about the LEDs on the Cisco C880 Series R outers, see the “LEDs” section on

page 1-23.

Cisco Integrated Services Router Hardware Installation Guide

1-58

Chapter 1 Product Overview

Cisco 881

FE LAN

3210

CONSOLE

AUX

FE WAN

12VDC 2.5-5A

(POE)

RESET

361125

1 2 3 4 5 7 8 9

361126

CiscoCisco

800

Series

OKOK

POEOE

PPPPPP

FE FE LAN

VPN

0 1 2

0 1

CD DATA

xDSL

ISDNISDN

LINKLINK

B1B1

B2B2

Figure 1-33 shows the back panel of the Cisco C88 1 Router.

Figure 1-33 Back Panel of the Cisco C881 Router

1 Primary WAN port—FE 6 Reset button 2 USB port 7 Power connector 3 4-port 10/100 Ethernet switch 8 Earth ground connection 4 Serial port—Console or auxiliary 9 Kensington security slot 5 On/Off switch

Cisco 860, 880, 890 Series

For information on installing the Cisco C880 Series Routers, see :

http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal l880-860.html

Cisco C886VA Router

Figure 1-34 shows the front panel of the Cisco C886VA Router.

Figure 1-34 Front Panel of the Cisco C886VA Router

1 LEDs

For detailed description about the LEDs on the Cisco C880 Series R outers, see the “LEDs” section on

page 1-23.

Cisco Integrated Services Router Hardware Installation Guide

1-59

Cisco 860, 880, 890 Series

VDSL/ADSL

over ISDN

ISDN

FE LAN

CONSOLE

AUX

3 2 1 0

12VDC

2.5

-5A

(POE)

RESET

361128

CiscoCisco

800

Series

OKOK

POEOE

PPPPPP

FE FE LAN

VPN

0 1 2

0 1

CD DATA

xDSL

ISDNISDN

LINKLINK

B1B1

B2B2

Figure 1-35 shows the back panel of the Cisco C88 6VA Router.

Figure 1-35 Back Panel of the Cisco C886VA Router

Chapter 1 Product Overview

VDSL/ADSL

over ISDN

ISDN

FE LAN

CONSOLE

(POE)

AUX

RESET

-5A

361127

21 3 4 5 6 8 9 10

1 Primary WAN port—VDSL/ADSL over

6 On/Off switch

ISDN

2 USB port 7 Reset button 3 ISDN 8 Power connector 4 4-port 10/100 Ethernet switch 9 Earth ground connection 5 Serial port—Console or auxiliary 10 Kensington security slot

For information on installing Cisco C880 Series Routers, see:

http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal l880-860.html

Cisco C886VAJ Router

1-60

Cisco Integrated Services Router Hardware Installation Guide

Figure 1-36 shows the front panel of the Cisco C886VAJ Router.

Figure 1-36 Front Panel of the Cisco C886VAJ Router

1 LEDs

For detailed description about LEDs on the Cisco 880 Series Router, see the “LEDs” section on

page 1-23.

Chapter 1 Product Overview

361129

VDSL/ADSLVDSL/ADSL

over ISDNover ISDN

ISDN

FE LANFE LAN

CONSOLECONSOLE

AUXAUX

3 2 1 0

12VDC 2.

2.5-5A-5A

(POE)(POE)

RESETRESET

21 3 4 5 6 8 9 10

Cisco

800

Series

POEOE

PPP

FE LAN

VPN

1 2

0 1

CD DATA

xDSL

Figure 1-37 shows the back panel of the Cisco C88 6VAJ Router.

Figure 1-37 Back Panel of the Cisco C886VAJ Router

Cisco 860, 880, 890 Series

1 Primary WAN port—VDSL/ADSL over

2 USB port 7 Reset button 3 ISDN 8 Power connector 4 4-port 10/100 Ethernet switch 9 Earth ground connection 5 Serial port—Console or auxiliary 10 Kensington security slot

For information on installing Cisco C880 Series Routers, see:

http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal l880-860.html

Cisco C887VA Router

Figure 1-38 shows the front panel of the Cisco C887VA Router.

Figure 1-38 Front Panel of the Cisco C887VA Router

ISDN

6 On/Off switch

PPP

xDSL

Cisco

361130

1 LEDs

For detailed description about the LEDs on Cisc o C880 Se ries Router, see the “LEDs” section on

page 1-23.

Cisco Integrated Services Router Hardware Installation Guide

1-61

Cisco 860, 880, 890 Series

361131

CiscoCisco 887887VA

VDSL/ADSLVDSL/ADSL

over POTSover POTS

FE LANFE LAN

3 2 1 0

CONSOLE

AUXAUX

12VDC 2.2.5-5A-5A

(POE)(POE)

RESETRESET

21 3 4 5 7 8 9

361132

CiscoCisco

800

Series

OKOK

POEOE

PPPPPP

FE FE LAN

VPN

1 2

0 1

CD DATA

xDSL

Figure 1-39 shows the back panel of the Cisco C88 7VA Router.

Figure 1-39 Back Panel of the Cisco C887VA Router

Chapter 1 Product Overview

1 Primary WAN port—VDSL/ADSL over

POTS

2 USB port 7 Power connector 3 4-port 10/100 Ethernet switch 8 Earth ground connection 4 Serial port—console or auxiliary 9 Kensington security slot 5 On/Off switch

For information on installing Cisco C880 series routers, see the following link:

http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal l880-860.html

Cisco C887VAM Router

Figure 1-40 shows the front panel of the Cisco C887VAM router:

Figure 1-40 Front Panel of the Cisco C887VAM Router

6 Reset button

1 LEDs

For detailed description about LEDs on Cisco C8 80 series router, see “LEDs” section on page 1-23.

Cisco Integrated Services Router Hardware Installation Guide

1-62

Chapter 1 Product Overview

361133

CiscoCisco 887887VAMAM

VDSL/ADSLVDSL/ADSL

over POTSover POTS

FE LANFE LAN

3 2 1 0

CONSOLE

AUXAUX

12VDC 2.2.5-5A-5A

(POE)(POE)

RESETRESET

21 3 4 5 7 8 9

Figure 1-41 shows the back panel of the Cisco C88 7VAM router.

Figure 1-41 Back Panel of the Cisco C887VAM Router

Cisco 860, 880, 890 Series

1 Primary WAN port—VDSL/ADSL over

6 Reset button

POTS

2 USB port 7 Power connector 3 4-port 10/100 Ethernet switch 8 Earth ground connection 4 Serial port—Console or auxiliary 9 Kensington security slot 5 On/Off switch

For information on installing the Cisco C880 Series Routers, see:

http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal l880-860.html

Cisco Integrated Services Router Hardware Installation Guide

1-63

Cisco 860, 880, 890 Series

Cisco C888 Integrated Services Router

The Cisco C888 Integrated Services Router (ISR) offers broadband speed s and sim plified mana geme nt to small businesses, enterprise small branches, and teleworkers. The Cisco C888 ISR supports multi mode G.SHDSL (EFM+ATM) WAN connectivity. The Cisco C888 ISR has a lead free, fanless chassis and it is an updated version of the previous Cisco 888 (888 A and 888 EA) ISR models.

Table 1-28 provides information about important hardware specifications pertaining to the Cisco C888

ISR.

Table 1-28 Hardware Specifications for Cisco C888 ISR

Hardware Description

Flash Memory 256 MB Main Memory 1-GB DDR RAM ; fixed, and not extendable USB port A USB 2.0-compliant port located at the back

FAN Fanless chassis. PoE Two internal PoE ports WAN 4-pair multimode G.SHDSL (EFM+ATM) with

Console or auxiliary port RJ-45 LAN switch 4-port 10/100BASE-T

Chapter 1 Product Overview

panel

ISDN backup.

Note If you change G.SHDSL mode from EFM to ATM or from ATM to EFM, you should reload the router.

Note EFM auto mode is supported only on the fir st pair . EFM manual mode can be supported on all the 4 pairs.

Note Cisco C888 ISR does not support Inverse Multiplexing over ATM (IMA) mode.

For detailed hardware specifications, see t he Cisco 880 Series hardware data sheet at:

http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_ Data_Sheet.html

Cisco Integrated Services Router Hardware Installation Guide

1-64

Chapter 1 Product Overview

361134

CiscoCi sco

800

Series

OKOK

POEOE

PPPPPP

FE FE LAN

VPN

0 1 2

0 1

CD DATA

xDSL

ISDNISDN

LINKLINK

B1B1

B2B2

EFMEFM

ATMATM

Figure 1-42 shows the front panel of the Cisco C888 Router:

Figure 1-42 Front Panel of the Cisco C888 Router

1 LEDs

For detailed description about the LEDs on the Cisco 880 Series Routers, see informa tion available at:

http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/1Overv iew880-860.html#wp1147924

Cisco 860, 880, 890 Series

Cisco Integrated Services Router Hardware Installation Guide

1-65

Cisco 860, 880, 890 Series

361135

FE LAN

3 2 1 0

CiscoCisco 888888

SHDSLSHDSL

RJ45 ONJ45 ONLY

ISDN

CONSOLE

AUXAUXAUXAUX

12VDC 2.2.5-5A-5A

(POE)(POE)

RESETRESET

2 31 4 5 6 8 9 10

Figure 1-43 shows the back panel of the Cisco C88 8 Router.

Figure 1-43 Back Panel of the Cisco C888 Router

Chapter 1 Product Overview

1 Primary WAN port—G.SHDSL 6 On/Off switch 2 USB port 7 Reset button 3 ISDN 8 Power connector 4 4-port 10/100 Ethernet switch 9 Earth ground connection 5 Serial port—console or auxiliary 10 Kensington security slot

For information on installing Cisco 800 Series Routers, see the information available at:

http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG/installin g.html#pgfId-1098019

Cisco Integrated Services Router Hardware Installation Guide

1-66

Chapter 1 Product Overview

Cisco 860, 880, 890 Series

Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers

Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers (ISRs) extend 4G LTE support to the existing Cisco 880 Series and Cisco 890 Series ISRs. The Cisco C880 Series and Cisco C890 Series 4G LTE ISRs are based on the Sierra W i reless MC7304 modem and Cisco C880 Series and Cisco C890 4G LTE Series ISRs can support higher data rates compared to 3G in both up link and do wn link directions with 4G LTE support.

This section provides information about the following models:

• Cisco C881G-4G ISR

• Cisco C887VAG-4G ISR

• Cisco C896VAG-LTE ISR

• Cisco C897VAG-LTE ISR

• Cisco C898EAG-LTE ISR

• Cisco C899G-LTE ISR

Table 1-29 provides information about important hardware specifications pertaining to Cisco C880 4G

LTE Series ISRs.

Table 1-29 Hardware Specifications for Cisco C880 4G LTE Series ISRs

Hardware Description

Flash Memory 1GB Main Memory 1-GB DDR RAM USB port A USB 2.0-compliant port located at the back

panel PoE Two PoE ports WAN

• C881G-4G— FE

• C887VAG-4G—VDSL or ADSL over POTS

Console or auxiliary port RJ-45 LAN switch 4-port 10/100BASE-T

Table 1-30 provides information about important hardware specifications pertaining to Cisco C890 4G

LTE Series ISRs.

Table 1-30 Hardware Specifications for Cisco C890 4G LTE Series ISRs

Hardware Description

Flash Memory 1 GB Main Memory 1-GB DRAM USB port A USB 2.0-compliant port located at the back

panel. PoE Four PoE ports

Cisco Integrated Services Router Hardware Installation Guide

1-67

Cisco 860, 880, 890 Series

Table 1-30 Hardware Specifications for Cisco C890 4G LTE Series ISRs

Chapter 1 Product Overview

Hardware Description

WAN • C896VAG-LTE—VDSL or ADSL over

ISDN, GE

• C897VAG-LTE—VDSL or ADSL over

POTS, GE

• C898EAG-LTE—G.SHDSL over POTS, GE

• C899G-LTE—GE, SFP

Console or auxiliary port RJ-45 LAN switch 8-port 10/100/1000 BASE-T

Cisco Integrated Services Router Hardware Installation Guide

1-68

Chapter 1 Product Overview

Table 1-31 lists the different 4G LTE SKUs available for the Cisco 880 and Cisco 890 series ISRs.

Cisco 860, 880, 890 Series

Cisco Integrated Services Router Hardware Installation Guide

1-69

Cisco 860, 880, 890 Series

Table 1-31 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs

Operating

SKU ID Mode

C881G-4G-GA-K9 LTE:

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Region Frequency Band Description

Global (Europe, New Zealand, and Australia)

4G:

• 800 MHz (band 20)

• 900 MHz (band 8)

• 1800 MHz (band 3)

• 2100 MHz (band 1)

• 2600 MHz (band 7)

3G (UMTS, HSPA+, HSPA):

• 800 MHz (band 6)

• 850 MHz (band 5)

• 900 MHz (band 8)

• 1900 MHz (band 2)

• 2100 MHz (band 1)

2G (GSM, EDGE, GPRS):

Chapter 1 Product Overview

Cisco 880 Series ISR Multimode LTE feature for global wireless networks. C881G-4G-GA-K9 comes with a Sierra Wireless MC7304 modem.

C887VAG-4G-GA-K9LTE:

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Global (Europe, New Zealand, and Australia)

• 850 MHz

• 900 MHz

• 1800 MHz

• 1900 MHz

4G:

• 800 MHz (band 20)

• 900 MHz (band 8)

• 1800 MHz (band 3)

• 2100 MHz (band 1)

• 2600 MHz (band 7)

3G (UMTS, HSPA+, HSPA):

• 800 MHz (band 6)

• 850 MHz (band 5)

• 900 MHz (band 8)

• 1900 MHz (band 2)

• 2100 MHz (band 1)

2G (GSM, EDGE, GPRS):

• 850 MHz

Cisco 880 series ISR with Multimode LTE feature for global wireless networks. C887VAG-4G-GA-K9 comes with a Sierra Wireless MC7304 modem.

Cisco Integrated Services Router Hardware Installation Guide

1-70

• 900 MHz

• 1800 MHz

• 1900 MHz

Chapter 1 Product Overview

Table 1-31 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

Operating

SKU ID Mode

C896VAG-LTE-GA-K9LTE:

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Region Frequency Band Description

Global (Europe, New Zealand, and Australia)

4G:

• 800 MHz (band 20)

• 900 MHz (band 8)

• 1800 MHz (band 3)

• 2100 MHz (band 1)

• 2600 MHz (band 7)

3G (UMTS, HSPA+, HSPA):

• 800 MHz (band 6)

• 850 MHz (band 5)

• 900 MHz (band 8)

• 1900 MHz (band 2)

• 2100 MHz (band 1)

2G (GSM, EDGE, GPRS):

Cisco 860, 880, 890 Series

Cisco 890 series ISR with Multimode LTE feature for global wireless networks. C896VAG-LTE-GA-K 9 comes with a Sierra Wireless MC7304 modem.

C897VAG-LTE-GA-K9LTE:

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Global (Europe, New Zealand, and Australia)

• 850 MHz

• 900 MHz

• 1800 MHz

• 1900 MHz

4G:

• 800 MHz (band 20)

• 900 MHz (band 8)

• 1800 MHz (band 3)

• 2100 MHz (band 1)

• 2600 MHz (band 7)

3G (UMTS, HSPA+, HSPA):

• 800 MHz (band 6)

• 850 MHz (band 5)

• 900 MHz (band 8)

• 1900 MHz (band 2)

• 2100 MHz (band 1)

2G (GSM, EDGE, GPRS):

• 850 MHz

Cisco 890 series ISR with Multimode LTE feature for global wireless networks. C897VAG-LTE-GA-K 9 comes with a Sierra Wireless MC7304 modem.

• 900 MHz

• 1800 MHz

• 1900 MHz

Cisco Integrated Services Router Hardware Installation Guide

1-71

Cisco 860, 880, 890 Series

Table 1-31 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

Operating

SKU ID Mode

C897VAMG-LTE-G A-K9

• LTE

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Region Frequency Band Description

Global (Europe, New Zealand, and Australia)

LTE:

• 800 MHz (band 20)

• 900 MHz (band 8)

• 1800 MHz (band 3)

• 2100 MHz (band 1)

• 2600 MHz (band 7)

3G (UMTS, HSPA+, HSPA):

• 800 MHz (band 6)

• 850 MHz (band 5)

• 900 MHz (band 8)

• 1900 MHz (band 2)

• 2100 MHz (band 1)

2G (GSM, EDGE, GPRS):

Chapter 1 Product Overview

Cisco 890 series ISR with Multimode LTE feature for global wireless networks. C897VAMG-LTE-GA

-K9 comes with a Sierra Wireless MC7304 modem.

• 850 MHz

• 900 MHz

• 1800 MHz

• 1900 MHz

Cisco Integrated Services Router Hardware Installation Guide

1-72

Chapter 1 Product Overview

Table 1-31 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

Operating

SKU ID Mode

C898EAG-LTE-GA

-K9

LTE:

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Region Frequency Band Description

Global (Europe, New Zealand, and Australia)

4G:

• 800 MHz (band 20)

• 900 MHz (band 8)

• 1800 MHz (band 3)

• 2100 MHz (band 1)

• 2600 MHz (band 7)

3G (UMTS, HSPA+, HSPA):

• 800 MHz (band 6)

• 850 MHz (band 5)

• 900 MHz (band 8)

• 1900 MHz (band 2)

• 2100 MHz (band 1)

2G (GSM, EDGE, GPRS):

Cisco 860, 880, 890 Series

Cisco 890 series ISR with Multimode LTE feature for global wireless networks. C898EAG-LTE-GA-K 9 comes with a Sierra Wireless MC7304 modem.

C899G-LTE-GA-K9 LTE:

• HSPA+

• HSPA

• UMTS

• EDGE

• GPRS

Global (Europe, New Zealand, and Australia)

• 850 MHz

• 900 MHz

• 1800 MHz

• 1900 MHz

4G:

• 800 MHz (band 20)

• 900 MHz (band 8)

• 1800 MHz (band 3)

• 2100 MHz (band 1)

• 2600 MHz (band 7)

3G (UMTS, HSPA+, HSPA):

• 800 MHz (band 6)

• 850 MHz (band 5)

• 900 MHz (band 8)

• 1900 MHz (band 2)

• 2100 MHz (band 1)

2G (GSM, EDGE, GPRS):

• 850 MHz

Cisco 890 series ISR with Multimode LTE feature for global wireless networks. C899G-LTE-GA-K9 comes with a Sierra Wireless MC7304 modem.

• 900 MHz

• 1800 MHz

• 1900 MHz

Cisco Integrated Services Router Hardware Installation Guide

1-73

Cisco 860, 880, 890 Series

372528

6 7 8 9 10 11

1 3

2 4

Cisco C881G-4G Integrated Services Router

Figure 1-44 shows the front panel of the Cisco C881G-4G ISR.

Figure 1-44 Front Panel of the Cisco C881G-4G ISR

1 Power OK 7 FE LAN 2 PPP 8 GPS 3 PoE 9 RSSI 4 FE WAN Port 10 4G 5 SIM 11 WWAN 6 VPN

Chapter 1 Product Overview

Table 1-32 describes the LEDs of the Cisco C881G-4G ISR.

Table 1-32 LED Descriptions for the Cisco C881G-4G ISR

Number LED Color Description

1 Power OK Green On—DC power is being supplied to the router and the

Cisco IOS software is running. Blinking—Boot up is in process, or t he route r is in

ROMM ON mode .

Off—Power is not supplied to the router. 2 PPP Green On—At least one PPP session is established. 3 PoE Green On—PoE is connected and powered.

Off—PoE is not installed.

Amber On—Fault with the PoE.

4FE WAN

Port Link

Green On—Port is connected.

Blinking—Data is either being received or transmitted.

Off—Port is not connected.

Cisco Integrated Services Router Hardware Installation Guide

1-74

Chapter 1 Product Overview

Table 1-32 LED Descriptions for the Cisco C881G-4G ISR

Number LED Color Description

5 SIM Green / Yellow

6 VPN G reen On—VPN is connected. 7 FE LAN

8 GPS Green (solid) Standalone GPS.

9 Received

Port Links Status

Signal Strength Indication (RSSI)

SIM in slot 0 is active, SIM in slot 1 is not. (one green blink followed by two yellow blinks)

Yello w / Green (one yellow blink followed by two green blinks)

Off / Green (two green blinks and then a pause)

Green / Off (slow blink

once and then a pause)

Off / Off No SIM present in either slots.

Green On—Ethernet port is connected.

Green (slow blinking)

Yellow (solid) Assisted GPS. Yello w (slow

blinking) Off GPS is not configured. Green (solid) Very strong signal. Green (three

blinks and then a long pause)

Green (two blinks and then a long pause)

Green (one blink and then a long pause)

Off No signal.

SIM in slot 1 active, SIM in slot 0 is not.

No SIM in slot 0, SIM present in slot 1.

SIM is present in slot0, no SIM in slot 1.

Blinking—Data is either being received or being

transmitted.

Off—Ethernet port is not connected.

GPS is acquiring signals.

Assisted GPS is acquiring signals.

Strong signal.

Fair signal.

Marginal signal.

Cisco 860, 880, 890 Series

Cisco Integrated Services Router Hardware Installation Guide

1-75

Cisco 860, 880, 890 Series

Table 1-32 LED Descriptions for the Cisco C881G-4G ISR

Chapter 1 Product Overview

Number LED Color Description

10 Service Green (solid) Service is active and the corresponding LED is lit based

on the service level that is active (2G, 3G, 3.5G, 3.7G, LTE).

Off No service.

11 WWAN Green Module is powered on and connected but not

transmitting or receiving.

Green (slow blinking)

Green (fast blinking)

Off Module is not powered.

Module is powered on and searching for connection.

Module is transmitting or receiving.

Cisco Integrated Services Router Hardware Installation Guide

1-76

Chapter 1 Product Overview

372522

1 2 3 4 5 6 8 1097

11121314

372529

6 7 8 9 10 11

1 3

2 4

Figure 1-45 shows the back panel of the Cisco C881G -4G ISR.

Figure 1-45 Back Panel of the Cisco C881G-4G ISR

1 Primary WAN port—FE 9 Earth ground connection 2 USB port 10 Kensington security slot

3 4G port 11 4G Antenna connector—M1/DIV 4 SIM slots 12 Power switch 5 4-port 10/100 Ethernet switch 13 Active GPS antenna connector

6 Serial port—Console or auxiliary 14 4G Antenna connector—M0/MAIN 7 Reset button 8 Power connector

Cisco 860, 880, 890 Series

For information on installing the Cisco C880 Series Routers, see:

http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG.html

Cisco C887VAG-4G Integrated Services Router

Figure 1-46 shows the front panel of the Cisco C887VAG-4G ISR.

Figure 1-46 Front Panel of the Cisco C887VAG-4G ISR

Cisco Integrated Services Router Hardware Installation Guide

1-77

Cisco 860, 880, 890 Series

Table 1-33 describes the LEDs for Cisco C887VAG-4G ISR.

Table 1-33 LED Descriptions for the Cisco C887VAG-4G ISR

Chapter 1 Product Overview

Number LED Color Description

1 Power OK Green On—DC power is being supplied to the router and the

Cisco IOS software is running. Blinking—Boot up is in process, or the router is in

ROMMON mode.

Off—Power is not supplied to the router. 2 PPP Green On—At least one PPP session is established. 3 PoE Green On—PoE is connected and powered.

Off—PoE is not installed.

Amber On—Fault with the PoE.

4 xDSL CD Green On—The xDSL interface is connected to the DSLAM.

Blinking—Training the line.

Off—Indicates that a connection has not been established

or the port is shut down.

xDSL Data Green Blinking—The xDSL interface is either receiving or

transmitting data.

Off—No data is being transmitted or received. 5 SIM Green / Yellow

SIM in slot 0 is active, SIM in slot 1 is not.

(one green blink followed by two yellow blinks)

Yellow / Green

SIM in slot 1 is active, SIM in slot 0 is not.

(one yellow blink followed by two green blinks)

Off / Green (two

No SIM in slot 0, SIM present in slot 1.

green blinks and then a pause)

Green / Off

SIM present in slot0, no SIM in slot 1.

(slow blink once and then a pause)

Off / Off No SIM present in either slots. 6 VPN Green On—V PN is connected. 7 FE LAN

Port Links Status

Green On—Ethernet p ort is connected.

Blinking—Data is either being received or transmitted. Off—Ethernet port is not connected.

Cisco Integrated Services Router Hardware Installation Guide

1-78

Chapter 1 Product Overview

Table 1-33 LED Descriptions (continued)for the Cisco C887VAG-4G ISR

Number LED Color Description

8 GPS Green (solid) Standalone GPS.

9 RSSI Green (solid) Very strong signal.

10 Service Green (Solid) Service is active and the correspon ding LED is lit based on

11 WWAN Green Module is powered on and connected but not transmitting

Green (slow blinking)

Yellow (solid Assisted GPS. Yello w (slow

blinking) Off GPS is not configured.

Green (three blinks and then a long pause)

Green (two blinks and then a long pause)

Green (one blink and then a long pause)

Off No signal.

Off No service.

Green (slow blinking)

Green (fast blinking)

Off Module is not powered.

GPS is acquiring signals.

Assisted GPS is acquiring signals.

Strong signal.

Fair s i gn a l .

Marginal signal.

the service level that is active (2G, 3G, 3.5G, 3.7G, LTE).

or receiving. Module is powered on and searching for connection.

Module is transmitting or receiving.

Cisco 860, 880, 890 Series

Cisco Integrated Services Router Hardware Installation Guide

1-79

Cisco 860, 880, 890 Series

372530

1 3

Figure 1-47 shows the back panel of the Cisco C887VAG-4G ISR.

Figure 1-47 Back Panel of the Cisco C887VAG-4G ISR

Chapter 1 Product Overview

10111214 13

372523

1 2 3 4 5 7 986

1 USB port 8 Earth ground connection

2 4G port 9 Kensington security slot 3 SIM slots 10 4G antenna connector—M1/DIV 4 4-port 10/100 Ethernet switch 11 Power switch

5 Serial port—Console or auxiliary 12 Active GPS antenna connector 6 Reset button 13 Primary WA N port—VDSL or ADSL over

7 Power connector 14 4G antenna connector—M0/MAIN

Cisco C896VAG-LTE Integrated Services Router

Figure 1-48 shows the front panel of the Cisco C896VAG-LTE ISR.

Figure 1-48 Front Panel of the Cisco C896VAG-LTE ISR

POTS

Cisco Integrated Services Router Hardware Installation Guide

1-80

Cisco 800 Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual