Cisco 7960G - IP Phone VoIP, 7960 - IP Phone - Telephone, 7940 Series, 7960 Series User Manual

Download

Page 1

Cisco IP Phone 7960 and 7940 Series User Guide

Corporate Headquarters

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 526-4100

Customer Order Number: DOC-7810182= Text Part Number: 78-10182-08

Page 2

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTW ARE LICENSE AND LIMITED WARRANTY FOR THE A CCOMPANYING PRODUCT ARE SET FOR TH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial enviro nment. This equipment generates, uses, and can radiate r adio- frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as

part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WAR RANTY HEREIN , AL L DOCU MENT FILES A ND SO FTWARE OF THESE SUPPLIERS ARE

PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WA RRANTIES, EXPRESSE D OR

IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF M ERCHANTABILITY, FITNESS F OR A PARTICULAR PURPOSE AND

NONINFRINGEMENT OR ARISING FROM A COURSE OF DEAL ING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LI ABLE F OR ANY IN DIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL

DAMAGES, INCLUDING, WITHOUT LIMITATION , LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCIP, the Cisco Arrow logo, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That’s Possible, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, En terprise/Solver, Et herChannel, EtherSw itch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, LightStream , MGX, MICA , the Networker s logo, Netw ork Regist rar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast, Strata View Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in t h e U .S. and cert ain other coun tries.

Page 3

All other trademarks mentioned in this do cument o r Web sit e ar e the property of thei r respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0208R)

Cisco IP Phone 7960 and 7940 Series User Guide

Page 4

Page 5

Preface xi

About this Guide xi

Related Topics

• Auto-Registering Your Phone Using TAPS, page 1-5

• A Road Map to Your C isco IP Phone, pag e 1-6

• Using the Handset, Headset, and Speakerphone, page 1-12

Auto-Registering Your Phone Using TAPS

Your administrator may ask you to auto-register your Cisco IP Phone using TAPS, the To ol for Auto-Registered Phones Support. TAPS might be used either for a new phone or to replace an existing phone.

Note You should follow this procedure only if your phone administrator asks you to.

Procedure

Step 1 If the phone is not already installed, follow the installation instructions available

in the

“Connecting Your Cisco IP Phone” section on page 1-2.

After you plug the phone into a port, the phone automatically registers and displays a number.

Step 2 Dial the TAPS extension provided by your system administrator. Step 3 A voice prompt asks you to select the language that you want to use. Choose

appropriately.

Step 4 Dial your personal extension number (provided by your system administrator),

then press the # key.

Note You may be instructed to enter the complete telephone number (in cluding

area code).

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

1-5

Page 26

A Road Map to Your Cisco IP Phone

Step 5 To confirm, enter your personal extension number again, followed by the # key.

The phone displays a confirmation message.

Step 6 Hang up the phone.

The phone resets and displays your extension number.

Related Topics

• Connecting Your Cisco IP Phone, page 1-2

• A Road Map to Your C isco IP Phone, pag e 1-6

• Using the Feature Buttons, page 1-10

• Navigating on Your Phone, page 1-11

• Using the Handset, Headset, and Speakerphone, page 1-12

Chapter 1 Introducing Your Cisco IP Phone

A Road Map to Your Cisco IP Phone

Refer to the following illustrations and table to identify the buttons and parts on your Cisco IP Phone and to find a description of related features.

Cisco IP Phone 7960 and 7940 Series User Guide

1-6

78-10182-08

Page 27

Chapter 1 Introducing Your Cisco IP Phone

Figure 1-1 Cisco IP Phone 7960

A Road Map to Your Cisco IP Phone

1617

Figure 1-2 Cisco IP Phone 7940

121314

1011

68561

78-10182-08

10111617 12131415

Cisco IP Phone 7960 and 7940 Series User Guide

68562

1-7

Page 28

A Road Map to Your Cisco IP Phone

Handset with indicator light

LCD screen Displays features such as the time, date, your phone

Cisco IP Phone model type

Line or speed dial button

Chapter 1 Introducing Your Cisco IP Phone

Functions like a traditional handset. The light strip at the top of the handset blinks when the phone rin gs and can be set to remain lit when you receive a voice mail message.

For more information on working with the handset, refer to the

Volume” section on page 2-1.

number, caller ID, line/call status and softkey tabs. Indicates your Cisco IP Phone mode l.

Opens a new line or speed dials the number on the LCD screen. Phones in the Cisco IP Phone 7960 series have six line or speed dial buttons and phones in the 7940 series have two.

“ Adjusting the Handset, Speakerph one, and Headset

Footstand

Allows you to adjust the angle of the phone base.

adjustment

Directories button

? but t o n Displays help on your LCD screen for a phone button or

Provides access to call histories and directories (see the

“Using the Feature Buttons” section on page 1-10.)

function (see the

“Using the Feature Buttons” section on

page 1-10.)

Settings button Provides access to phone settings such as contrast and ring

sound, network conf iguration, and st atus informat ion (see the

“Using the Feature Buttons” section on page 1-10.)

Speaker button Toggles the speaker on or off.

Mute button Toggles the mute on or off.

Headset button Toggles the headset on or off.

Cisco IP Phone 7960 and 7940 Series User Guide

1-8

For more information on working with the headset, refer to the

“Using the Headset” section on page 1-14.

78-10182-08

Page 29

Chapter 1 Introducing Your Cisco IP Phone

Volume button Increases or decreases volume for the handset, headset, or

Services button Provides access to any available phone services (see the

Messages button

A Road Map to Your Cisco IP Phone

speakerphone (depending upon which is current ly activ e). Also controls the ringer volume (if the handset is in its cradle), and the LCD screen contrast.

For more information on adjusting the volume, refer to the

“Adjusting the Handset, Speakerphone, and Headset Volume” section on page 2-1 and the “Adjusting the Ringer Volume” section on page 2-2.

“Using the Feature Buttons” section on page 1-10.)

Provides access to a message system, if available (see the

“Using the Feature Buttons” section on page 1-10.)

Navigation button

Enables you to scroll through text and select features displayed on the LCD screen (see the

“Navigating on Y our

Phone” section on page 1-11.).

Dial pad Works exactly like the dial pad on a traditional telephone.

Softkeys Enable you to engage any of the functions displayed on the

corresponding LCD screen tabs. Softkeys point to feat ure options displayed along the bottom of your LCD screen. Softkeys change depending on the status of your phone. For example, you can see one set of softkey options when you pick up the handset, and another set when the phone is not in use.

Related Topics

• Using the Feature Buttons, page 1-10

• Navigating on Your Phone, page 1-11

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

1-9

Page 30

Using the Feature Buttons

Your Ci sco IP Phone has five feature buttons:

• Services button—Displays services on your phone’s LCD screen. These are

services to which you have already subscribed using the Cisco CallManager User Options web pages. Your system administrator determines the services that are available to you. For more information, see the

IP Phone Services” section on page 1-18.

• Messages button—Provides access to your voice mail message system. For

more information, see the

• Settings button—Displays network settings on your phone’s LCD screen,

plus options for adjusting your phone’s ringer sound and LCD screen contrast.

• Directories button—Displays various directories on your phone’s LCD

screen, including missed, received, and placed calls. You can use each of these directories to locate phone numbers and you can dial those numbers from the directories. For more information, see the

from the Phone Logs” section on page 3-21 and the “Searching and Dialing from the Phone Directory” section on page 3-23.

Chapter 1 Introducing Your Cisco IP Phone

“Establishing Cisco

“Using Voice Mail” section on page 3-21.

“Viewing and Dialing

• ? button—Displays helpful information about buttons and features.

For help with:

–

A specific button or softkey—Press the ? button once, then press the button or softkey to display information about that button or key.

–

A specific feature—First press the Directories, Settings, or Services buttons to display a list of available features. Use the Navigation button to scroll through the list and select a feature. Press the ? button twice quickly to display information about the selected feature.

–

The ? button feature itself—Press the ? button twice quickly (without first selecting a feature). This brings up help about using the ? button.

–

Viewing network statistics about a call you are actively on—Press the ? button twice quickly during the call.

Related Topics

• A Road Map to Your C isco IP Phone, pag e 1-6

• Navigating on Your Phone, page 1-11

Cisco IP Phone 7960 and 7940 Series User Guide

1-10

78-10182-08

Page 31

Chapter 1 Introducing Your Cisco IP Phone

• Personalizing the Ringer Sound, page 2-3

• Changing the LCD Screen Contrast, page 2-5

• Accessing Network Configuration Data, page C-1

• Accessing Status Data, page C-2

Navigating on Your Phone

Navigating on your Cisco IP Phone is easy. You use the Navigation button, the softkeys, and the key pad to make your selections:

• Softkeys correspond to the option tabs displayed along the bottom of your

LCD screen. Softkeys change depending on the status of your phone. For example, you can see one set of softkey options when you pick up the handset, and another set when the phone is not in use.

Navigating on Your Phone

• The >> softkey allows you to re-position your cursor. The << softkey allows

you to delete a character or digit in an entry. Press the << softkey or the Delete softkey if you make a mistake or need to edit an entry. The Delete

softkey allows you to edit a character or digit—it does not delete the entire entry.

• You can choose menu items on your Cisco IP Phone in more than one way:

–

Using the Navigation button—Press the Navigation button (this is the button with the up and do wn arro ws) to select (or highlight) a menu it em. Then press the Select softkey.

–

Using an Item Number—You can press the number key on your phone’s key pad that corresponds to the item number displayed on the LCD screen. Use this method to select any menu item that has an item number to the left of it

• To enter any letter on your LCD screen, use a corresponding number key.

Press the key one or more times to display a particular letter. For example, press the 2 key one time for “a,” twice quickly for “b,” and three times quickly for “c.” After you pause, the cursor automatically advances to allow you to enter the next letter. Press the << softkey if you make a mistake.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

1-11

Page 32

Chapter 1 Introducing Your Cisco IP Phone

Using the Handset, Headset, and Speakerphone

Related Topics

• A Road Map to Your C isco IP Phone, pag e 1-6

• Using the Feature Buttons, page 1-10

Using the Handset, Headset, and Speakerphone

Your Cisco IP Phone works with a handset, headset, or speakerphone. For information on using each of these, refer to the following sections:

• Using the Handset, page 1-12

• Adjusting the Handset Rest, page 1-12

• Using the Speakerphone, page 1-14

• Using the Headset, page 1-14

Using the Handset

The handset on your Cisco IP Phone functions in the same way as a handset on a traditional phone:

• To place and answer calls with the handset, simply lift the handset.

• To hang up, place the handset back in its cradle.

• T o switch from the handset to the speakerphone, press the Speaker button on

the front of your phone during a call, th en hang u p the handset .

Related Topics

• Adjusting the Handset Rest, page 1-12

• Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1

Adjusting the Handset Rest

If you mount your Cisco IP Phone on the wall or use the footstand on the phone, you can adjust the handset rest to ensure the receiver will not slip out of the cradle.

To adjust the handset rest, follow the steps and refer to Figure 1-3.

Cisco IP Phone 7960 and 7940 Series User Guide

1-12

78-10182-08

Page 33

Chapter 1 Introducing Your Cisco IP Phone

Figure 1-3 Using the Handset Rest

1 2 3

Using the Handset, Headset, and Speakerphone

Set the handset aside and use your thumb and finger to grasp and pull out the square plastic tab in the handset rest.

Rotate the tab 180 degrees.

Slide the tab back into the handset rest with the extension protrud ing from the top of the tab.

Replace the handset in the rest. The tab hooks into a slot in the handset to ensure that the handset will not slip out of the rest.

Related Topics

• Using the Handset, page 1-12

77354

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

1-13

Page 34

Using the Handset, Headset, and Speakerphone

Using the Speakerphone

You can use the speakerphone in conjunction with all of the features on your Cisco

IP Phone.

To place and answer calls using the speakerphone, press the Speaker butt o n . To switch from speakerphone to handset during a call, simply lift the handset.

Related Topics

• Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1

Using the Headset

You can use the headset in conjunction with all of the features on your Cisco

IP Phone, including the Volume and Mute buttons. Use these buttons to adjust the volume to the ear piece and to mute the speech path from the headset microphone.

Chapter 1 Introducing Your Cisco IP Phone

T o place and answer calls using a headset, plug an approved headset into the back of the phone base and press the Headset button on the front of your phone.

Your phone supports four- or six-wire headset jacks. For information about purchasing headsets, see the following URLs:

• http://cisco.getheadsets.com

• http://vxicorp.com/cisco

Caution Use only Cisco-appr oved headsets.

Warning

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).

Cisco IP Phone 7960 and 7940 Series User Guide

1-14

78-10182-08

Page 35

Chapter 1 Introducing Your Cisco IP Phone

Customizing Your Phone From the User Options Web Pages

Warning

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

on page 1-4 illustrates the headset port and other cable connection ports on your

phone.

Related Topics

• Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1

Customizing Your Phone From the User Options Web Pages

You can use th e Cisco Cal lManage r User Option s web pa ges to subsc ribe to services. Services include web-based information and special phone features.

In addition to subscribing to services, you can use the Cisco CallManager User Options web pages to:

78-10182-08

• set up call forwarding rules—Forwarding Calls to Another Extension,

page 3-14

• change the language in which you view phone information—Changing the

Language for the Phone LCD Screen, page 2-6

• specify a policy for the message waiting indicator light on your phone’s

handset—

• assign speed dial buttons for your Cisco IP Phone—Using Speed Dial,

page 3-12

• manage personal contacts—, page 4-5

Note If you use the Cisco CallManager Extension Mobility service, changes that you

make from the User Options web pages are maintained in your device profile. .

Adjusting the Message Waiting Indicator Light, page 2-4

Cisco IP Phone 7960 and 7940 Series User Guide

1-15

Page 36

Customizing Your Phone From the User Options Web Pages

You can also get a copy of the documentation av ailable for your phone on the User Options Pages.

This section covers the following topics:

• Logging In to the User Options Web Pages, page 1-16

• Changing the Default Language for the User Options Web Pages, page 1-17

• Establishing Cisco IP Phone Services, page 1-18

Logging In to the User Options Web Pages

Follow these instructions to log on and to access the main menu.

Procedure

Chapter 1 Introducing Your Cisco IP Phone

Step 1 Use your Web browser to access the URL provided by you r syst em administrator.

The Cisco CallManager User Opti ons Log On pag e appears.

Step 2 Enter your user ID and your password and click Log On. Your user ID and

password are provided by your system administrator. The Cisco CallManager User Opti ons Menu p age appears.

Step 3 Select your phone or, if applicable, your Cisco CallManager Extension Mobility

device profile from the “Select a device to configure” drop-down list. The menu is context-sensitive and displays options appropriate for the device or

device profile that you have selected.

Related Topics

• Changing the Default Language for the User Options Web Pages, page 1-17

• Establishing Cisco IP Phone Services, page 1-18

Cisco IP Phone 7960 and 7940 Series User Guide

1-16

78-10182-08

Page 37

Chapter 1 Introducing Your Cisco IP Phone

Customizing Your Phone From the User Options Web Pages

Changing the Default Language for the User Options Web Pages

Use this procedure to change the default language (French or English, for example) in which information is di splayed o n the Cisc o CallMana ger User Options web pages.

If you use the Cisco CallManager Extension Mobility service, follow this procedure to change the default language for both your device profile and your User Options web pages.

To temporarily change the language for the User Options web pages, click the “View page in” drop-down list located at the bottom of each web page. This changes the language displayed for the current web session. The next time that you log on, the User Options web pages will display in the default language.

Before You Begin

“Logging In to the User Options Web Pages”

section on page 1-16.

Procedure

Step 1 From the User Options main menu, select your phone or, if applicable, your

Cisco

CallManager Extension Mobility device profile from the Select a device to configure drop-down list.

The menu is context-sensitive and displays options appropriate for the device or device profile that you have selected.

Step 2 The next step depends upon your selection from the Select a d evice to configure

drop-down list:

a. If you selected your phone (and not a device profile), click Change the

Locale for these web pages.

b. If you selected a device profile, click Change the Locale for your device

profile(s) and these web pages.

Note You will not have access to a device profile unless you use the

Cisco CallManager Extension Mobility service.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

1-17

Page 38

Customizing Your Phone From the User Options Web Pages

Step 3 Select the language that you want to use as the default language from the “User

Locale” drop-down list and click Update. The language that you have selected now serves as the default la nguage for eac h

of the User Options web pages in the current web session and in future sessions. If you use Cisco

CallManager Extension Mobility, the default language will

display on the LCD screen the next time you log on to a Cisco IP Phone.

Step 4 When you are finished, click Return to the Menu or Log Off at the bottom of the

page.

Related Topics

• Changing the Language for the Phone LCD Screen, page 2-6

• Logging In to the User Options Web Pages, page 1-16

Chapter 1 Introducing Your Cisco IP Phone

• Establishing Cisco IP Phone Services, page 1-18

Establishing Cisco IP Phone Services

You can access information services, such as weather, stock quotes, and other services available at your company, using your Cisco IP Phone’s LCD display. Before accessing these services on your phone, your system administrator must customize them and make them a vailable to you. Additional ly , you must subscribe to the services that you want to appear on your phone.

To view services that you have subscribed to, press the Services button on your Cisco IP Phone. Use the Navigation b utton to select the desired service, then press the Select softkey to display information about that service. When you are finished, press the services button to exit the Services menu.

You can subscribe to the same service multiple times and give each instance of the same service a unique name. For example, if you want to subscribe to a weather service for several regions, you can rename each version.

The following topics describe how to establish services with the User Options web pages:

• Subscribing to Services, page 1-19

• How to Change or End Subscriptions, page 1-20

Cisco IP Phone 7960 and 7940 Series User Guide

1-18

78-10182-08

Page 39

Chapter 1 Introducing Your Cisco IP Phone

Related Topics

• Logging In to the User Options Web Pages, page 1-16

• Changing the Default Language for the User Options Web Pages, page 1-17

Subscribing to Services

Follow these steps to subscribe to services.

Before You Begin

section on page 1-16.

Procedure

Customizing Your Phone From the User Options Web Pages

“Logging In to the User Options Web Pages”

Step 1 From the User Options main menu, click Configure your Cisco IP Phone

Services.

The Subscribe/Unsubscribe IP Phone Services page appears.

Step 2 Select the service you want to add to your phone from the “Available Services”

drop-down list.

Step 3 Click Continue. Step 4 Enter any required information. For example, if the service is “movie times,” you

might need to enter your zip code to enable the service to display movies in your location.

Step 5 When you are done, click Subscribe to save your settings. To restore your

previous settings, click Back.

Note If your phone uses Cisco CallManager Extension Mobility , you will need

to log out and then log back in to the extension mobility service on your IP Phone before the changes take effect.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

1-19

Page 40

Customizing Your Phone From the User Options Web Pages

Step 6 To subscribe to another service, click New Subscription in the Subscribed

Services pane. To exit, click Return to the Menu or Log Off at the bottom of the page.

Related Topics

• Establishing Cisco IP Phone Services, page 1-18

• How to Change or End Subscriptions, page 1-20

How to Change or End Subscriptions

You can change or end your current subscriptions at any time. To do so, follow these steps.

Chapter 1 Introducing Your Cisco IP Phone

Before You Begin

“Logging In to the User Options Web Pages”

section on page 1-16.

Procedure

Step 1 From the User Options main menu, click Configure your Cisco IP Phone

Services. The Subscribe/Unsubscribe IP Phone Services page appears.

Step 2 In the Y our Subscribed Services pane, click on the service that you want to change

or end.

Step 3 If you want to change your subscription, change the information in the desired

fields and click Update. Or, click Unsubscribe to end your subscription to the service.

Note If your phone uses Cisco CallManager Extension Mobility , you will need

to log out and then log back in to the extension mobility service on your IP Phone before the changes take effect.

Cisco IP Phone 7960 and 7940 Series User Guide

1-20

78-10182-08

Page 41

Chapter 1 Introducing Your Cisco IP Phone

Step 4 When you are finished, click Return to the Menu or Log Off at the bottom of the

page.

Related Topics

• Subscribing to Services, page 1-19

• Establishing Cisco IP Phone Services, page 1-18

Customizing Your Phone From the User Options Web Pages

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

1-21

Page 42

Customizing Your Phone From the User Options Web Pages

Chapter 1 Introducing Your Cisco IP Phone

Cisco IP Phone 7960 and 7940 Series User Guide

1-22

78-10182-08

Page 43

CHAPTER

Customizing Phone Settings

These procedures help you personalize settin gs for your Cisco IP Ph one:

• Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1

• Adjusting the Ringer Volume, page 2-2

• Personalizing the Ringer Sound, page 2-3

• Adjusting the Message Waiting Indicator Light, page 2-4

• Changing the LCD Screen Contrast, page 2-5

• Changing the Language for the Phone LCD Screen, page 2-6

Adjusting the Handset, Speakerphone, and Headset Volume

Y ou can adjust the volume of the caller for the handset, speak erphone, and headset individually. When you change the volume for one, the others are not effected.

Follow these steps to adjust the volume on the handset, speakerphone, or headset.

Procedure

Step 1 Press the up or down Volume button when the handset, speakerphone, or headset

is in use.

Cisco IP Phone 7960 and 7940 Series User Guide

78-10182-08

2-1

Page 44

Adjusting the Ringer Volume

Note If you press the Volume button when none of these are in use, you are

Step 2 To save this volume setting for future calls, press the Save softkey.

If you adjust the vo lume during a call without p ressing Save, you are changing the volume level only for the duration of that particular call; on subsequent calls, the volume level will revert to the previously saved setting.

Related Topics

• Adjusting the Ringer Volume, page 2-2

Chapter 2 Customizing Phone Settings

adjusting the ringer volume. For details, see the

Volume” section on page 2-2.

“Adjusting the Ringer

• Personalizing the Ringer Sound, page 2-3

• Changing the LCD Screen Contrast, page 2-5

Adjusting the Ringer Volume

To change the volume used by the ringer, press the up or down Volume button while the handset is in its cradle. Continue to press the Volume button to hear sample rings and to adjust the volume to the desired level. The ringer volume is automatically saved.

Related Topics

• Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1

• Personalizing the Ringer Sound, page 2-3

• Changing the LCD Screen Contrast, page 2-5

Cisco IP Phone 7960 and 7940 Series User Guide

2-2

78-10182-08

Page 45

Chapter 2 Customizing Phone Settings

Personalizing the Ringer Sound

You can change the sound your phone makes when it rings to suit your tastes and to help you differentiate between your phone ringing and another nearby phone, or to differentiate between different lines on your own phone.

Follow these steps to change the sound used by the ringer.

Procedure

Step 1 Press the Settings but t o n . Step 2 From the Settings menu, use the Navigation b utton t o select Ring Type and press

the Select softkey.

Step 3 If you have multiple lines, use the Navigation button to scroll through the list of

your lines. When you find the line you want to config ure, press the Select softkey.

Personalizing the Ringer Sound

Note You can only use six different ring tones on yo ur phone, If you ha v e more

than six lines, some of your lines must share a ring tone.

Step 4 Use the Navigation button to scroll through the list of ring types and press the

Play softkey to hear the selected ring type.

Step 5 When you find the ring you want, press the Select softkey to check the

corresponding check box. To set the ring tone back to the default ring tone, select Default from the list.

Step 6 Press the OK softkey to accept and save your ringer selection. Step 7 Press the Save softkey to save all of your settings and to exit the Settings menu.

Related Topics

• Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1

• Adjusting the Ringer Volume, page 2-2

• Changing the LCD Screen Contrast, page 2-5

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

2-3

Page 46

Chapter 2 Customizing Phone Settings

Adjusting the Message Waiting Indicator Light

You can change the behavior policy of the message waiting indicator light (or “lamp”) for each line appearance on your Cisco IP Phone. The message waiting indicator is the red strip on your phone’s handset that blinks when you receive an incoming call. In its default state, the message waiting indicator light is usually configured to remain lit when you receive a new voice mail message. However, the default policy is determined by your system administrator.

Follow these steps to specify the message waiting indicator light policy (on, off, or default) for one or more of your phone lines.

Before You Begin

section on page 1-16.

“Logging In to the User Options Web Pages”

Procedure

Step 1 From the User Options w eb page, cl ick Change the Message Waiting Lamp

policy for your phone. The Change Your Message Waiting Lamp Policy page appears.

Step 2 Click the drop-down list that corresponds to the line that you want to change.

Choose Use System Policy, Always light, or Never light.

Step 3 Click Update. Step 4 When you are finished, click Return to the Menu or Log Off at the bottom of the

page.

Related Topics

• Using Voice Mail, page 3-21.

Cisco IP Phone 7960 and 7940 Series User Guide

2-4

78-10182-08

Page 47

Chapter 2 Customizing Phone Settings

Changing the LCD Screen Contrast

To improve the readability of the LCD screen, follow these steps to adjust the contrast.

Procedure

Step 1 Press the Settings but t o n . Step 2 From the Settings menu, use the Navigation button to select Contrast. Step 3 Perform one of the following:

• To set the desired contrast level—press the Up or Down softkeys (or the

Volume buttons).

• T o restore your pre viously sav ed contrast setting—press the more softkey and

then the Restore softkey.

Changing the LCD Screen Contrast

• To restore the factory default contrast setting—press the more softkey and

then the Factory softkey.

Step 4 Press the OK softkey to accept and save your changes.

Related Topics

• Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1

• Adjusting the Ringer Volume, page 2-2

• Personalizing the Ringer Sound, page 2-3

• Adjusting the Message Waiting Indicator Light, page 2-4

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

2-5

Page 48

Chapter 2 Customizing Phone Settings

Changing the Language for the Phone LCD Screen

Use this procedure to change the default language in which information is displayed on the Cisco IP Phone’s LCD screen.

Note If you use the Cisco CallManager Extension Mobility service, follow the

procedure described in the

Web Pages” section on page 1-17. This procedure allows you to change the

default language for your device profile.

Before You Begin

section on page 1-16.

“Changing the Default Language for the User Options

“Logging In to the User Options Web Pages”

Procedure

Step 1 From the User Options main menu, select your phone from the “Select a device

to configure” drop-down list.

Step 2 Click Change the Locale for this phone.

The Select a User Locale for your Phone page appears.

Step 3 Select the language that you want to use as the default language from the “User

Locale for this phone” drop-down list and click Update. The language that you have selected now serves as the default language for your

Cisco IP Phone LCD screen. If you change the default language for your phone’s LCD screen while you are on

an active call, the phone waits for you to end the call before updating the LCD screen.

Step 4 When you are finished, click Return to the Menu or Log Off at the bottom of the

page.

Cisco IP Phone 7960 and 7940 Series User Guide

2-6

78-10182-08

Page 49

Chapter 2 Customizing Phone Settings

Related Topics

• Changing the LCD Screen Contrast, page 2-5

• Changing the Default Language for the User Options Web Pages, page 1-17

Changing the Language for the Phone LCD Screen

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

2-7

Page 50

Changing the Language for the Phone LCD Screen

Chapter 2 Customizing Phone Settings

Cisco IP Phone 7960 and 7940 Series User Guide

2-8

78-10182-08

Page 51

CHAPTER

Placing a Call and Other Basic Phone Tasks

Basic phone tasks include placing, receiving and forwarding calls. The following sections describe how to perform these ba sic tasks o n your Cisco IP Ph one:

• Making Telephone Calls, page 3-1

• Using Speed Dial, page 3-12

• Forwarding Calls to Another Extension, page 3-14

• Making Conference Calls, page 3-17

• Using Voice Mail, page 3-21

• Viewing and Dialing from the Phone Logs, p age 3-21

• Searching and Dialing from the Phone Directory, page 3-23

Caution Using a cell or mobile phone in close proximity to a Cisco IP Phone might cause

interference.

Making Telephone Calls

These sections describe how you can place, answer, or otherwise manage a telephone call:

• Placing a Call, page 3-2

• Answering a Call, page 3-4

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-1

Page 52

Making Telephone Calls

Placing a Call

Chapter 3 Placing a Call and Other Basic Phone Tasks

• Ending a Call, page 3-4

• Muting a Call, page 3-5

• Putting a Call on Hold, page 3-6

• Transferring a Call to Another Extension, page 3-7

• Redialing the Last Number Dialed, page 3-8

• How to Get Notified When a Busy Line is Available Using Cisco Call Back,

page 3-8

• Storing and Retrieving a Call Using Call Park, page 3-9

• Answering Calls on Another Extension Using Call Pickup, page 3-10

Table 3-1 lists the different ways you can place a call with your Cisco IP Phone.

Ta b l e 3-1 Placing calls on your Cisco IP Phone

If you want to... Then...

use the receiver Lift the handset and dial the number. dial from one of your multiple

lines make a new call on the current

Press the line button that corresponds with your extension and dial the number that you want to reach.

Press the NewCall softkey and dial the number.

line dial with the phone on hook From the main screen, dial the number and press the Dial softkey.

The phone will not produce a dial tone until after yo u press the Dial softkey.

You can also press a line button, the Headset button, the Speaker button, or lift the receiver to place the call.

Note If you are dialing with the phone on hook, you canno t use *

or # as the leading digit. If you need to use these keys, dial with the phone off hook.

use a headset Press the Headset button and dial the number. use the speakerphone Press the Speaker button and dial the number.

Cisco IP Phone 7960 and 7940 Series User Guide

3-2

78-10182-08

Page 53

Chapter 3 Placing a Call and Other Basic Phone Tasks

Table 3-1 Placing calls on your Cisco IP Phone (continued)

If you want to... Then...

Making Telephone Calls

redial the most recently dialed

Press the Redial softkey.

number use speed dial numbers Press a Speed dial button to place a call to the corresponding

number. See the “Using Speed Dial” section on page 3-12 for details.

use a directory Select a number from one of the directories, then press the Dial

softkey. See the “Viewing and Dialing from the Phone Logs” section on

page 3-21 for details.

dial a Personal Address Book entry

Refer to the “Dialing a Personal Address Book Entry” section on

page 5-9.

dial a Personal Fast Dial number Refer to the “Dialing a Personal Fast Dials Entry” section on

page 5-20.

Tip If you receive a busy tone or a ring with no answer when you call another

extension, you can use the Cisco extension is available. See the

Call Back feature to get an alert when the

“How to Get Notified When a Busy Line is

Available Using Cisco Call Back” section on page 3-8.

Related Topics

• A Road Map to Your C isco IP Phone, pag e 1-6

• Answering a Call, page 3-4

• Ending a Call, page 3-4

• How to Get Notified When a Busy Line is Available Using Cisco Call Back,

page 3-8

• Redialing the Last Number Dialed, page 3-8

• Using Speed Dial, page 3-12

• Making Conference Calls, page 3-17

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-3

Page 54

Chapter 3 Placing a Call and Other Basic Phone Tasks

Making Telephone Calls

Answering a Call

Table 3-2 lists ways to answer an incoming call:

Ta b l e 3-2 Answering a Call

If you want to... Then...

use the handset Lift the handset. use a headset If the Headset button:

• is not lit, then press it.

• is lit, then press the Answer softkey or the line button of the

incoming call.

use the speakerphone Press the Answer softkey or the Speaker butt o n . use the AutoAnswer feature The phone will automatically answer the call when your phone

receives it, if your administrator turned AutoAnswer on for your extension.

Related Topics

• Placing a Call, page 3-2

• Ending a Call, page 3-4

• Muting a Call, page 3-5

• Putting a Call on Hold, page 3-6

• Answering Calls on Another Extension Using Call Pickup, page 3-10

Ending a Call

Table 3-3 lists ways to end a call:

Ta b l e 3-3 Ending a Call

If you are using... Then...

the handset Hang up the handset.

Cisco IP Phone 7960 and 7940 Series User Guide

3-4

78-10182-08

Page 55

Chapter 3 Placing a Call and Other Basic Phone Tasks

Making Telephone Calls

Table 3-3 Ending a Call (continued)

If you are using... Then...

a headset Press the Headset button or the EndCall softkey. the speakerphone Press the Speaker button or the EndCall softkey.

Related Topics

• Placing a Call, page 3-2

• Answering a Call, page 3-4

• Transferring a Call to Another Extension, page 3-7

• Forwarding Calls to Another Extension, page 3-14

Muting a Call

You can mute the handset, headset, or speakerphone during a call. The mute feature temporarily disables your phone’ s microphone. Mute pre vent s the party or parties on the other end of the line from hearing you, but does not interfere with your ability to hear them.

To mute a call, press the Mute button. To disengage mute, press Mute again.

Related Topics

• Placing a Call, page 3-2

• Answering a Call, page 3-4

• Ending a Call, page 3-4

• Putting a Call on Hold, page 3-6

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-5

Page 56

Making Telephone Calls

Putting a Call on Hold

When you put a call on hold, the call remains active ev en though you and the other party cannot hear one a not her. You can an swer othe r call s w hil e a cal l is on hol d.

Note Engaging the Hold feature generates music or a beeping tone. For this reason,

avoid putting a conference call on hold.

Table 3-4 lists ways to use the Hold feature:

Ta b l e 3-4 Putting a Call on Hold

If you... Then...

want to put a call on hold Press the Hold softkey.

Chapter 3 Placing a Call and Other Basic Phone Tasks

want to resume a call on hold Press the Resume softkey. have multiple calls on hold Use the Navigation b utton to select the desired call before you press

Resume.

have multiple calls on multiple lines on hold

Press the line button for the line to which you want to switch and use the Navigation button to select the desired call. Press Resume.

If you cannot use the Navigation button because on ly one lin e displays on your phone’s LCD screen, press the line button next to the call that you want to resume.

If your phone opens a new line when y ou press the line butt on, press the EndCall softkey to return to the desired call.

Tip If you are using multiple lines, to see the phone numb e r for

a call you have on hold, press the ? button followed by the line button of the call on hold.

Related Topics

• Placing a Call, page 3-2

• Answering a Call, page 3-4

• Ending a Call, page 3-4

• Muting a Call, page 3-5

• Transferring a Call to Another Extension, page 3-7

Cisco IP Phone 7960 and 7940 Series User Guide

3-6

78-10182-08

Page 57

Chapter 3 Placing a Call and Other Basic Phone Tasks

Transferring a Call to Another Extension

Follow these steps to transfer a call to another phone.

Procedure

Step 1 During a call, press the Trnsfer softkey. This puts the call on hold. Step 2 Dial the number or office extension to which you want to transfer the call. Step 3 When it rings on the other end, press Trnsfer again. Or, when the party answers,

announce the call and then press Trnsfer.

Step 4 If you are using a han dset, hang up .

If the party refuses the call, press the Resume softke y to return to the original call.

Making Telephone Calls

Related Topics

• Placing a Call, page 3-2

• Answering a Call, page 3-4

• Ending a Call, page 3-4

• Storing and Retrieving a Call Using Call Park, page 3-9

• Forwarding Calls to Another Extension, page 3-14

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-7

Page 58

Making Telephone Calls

Redialing the Last Number Dialed

To redial the most recently dialed number, press the Redial softkey. Doing so without lifting the handset activates the speakerphone or headset.

T o redial a number from a l ine other than your primary line, select t he desired line button and then press Redial.

Related Topics

• Placing a Call, page 3-2

• Ending a Call, page 3-4

• How to Get Notified When a Busy Line is Available Using Cisco Call Back,

page 3-8

Chapter 3 Placing a Call and Other Basic Phone Tasks

How to Get Notified When a Busy Line is Available Using Cisco Call Back

If you call an extension and the line is busy or the call goes unanswered, you can use the Cisco take a call.

Procedure

Step 1 Call an extension. While you hear the busy tone or ringing tone, press the

CallBack softkey. A CallBack activation confirmation message displays.

Note Y ou cannot acti vate call back notification if the cal led party has forwarded

Step 2 Press the Exit softkey to close the confirmation screen or press the Cancel softkey

to cancel the call back notification.

Call Back feature to be notified when the extension is available to

all calls to another extension.

Cisco IP Phone 7960 and 7940 Series User Guide

3-8

78-10182-08

Page 59

Chapter 3 Placing a Call and Other Basic Phone Tasks

Step 3 T o verify the statu s of the call back notif ication, press the CallBack softke y while

your phone is idle. A confirmation message displays. Press the Exit softkey to close the conf irmation screen or press the Cancel softkey

to cancel call back notification.

Step 4 When the extension you called is available to receiv e a call, you receive an audio

and visual alert from your phone. Press Dial to dial the number.

Related Topics

• Placing a Call, page 3-2

• Answering a Call, page 3-4

• Ending a Call, page 3-4

Making Telephone Calls

• Redialing the Last Number Dialed, page 3-8

Storing and Retrieving a Call Using Call Park

Park a call when you want to store the call before retr ievi ng it from another phone in the Cisco CallManager sy stem (for example, a phone in someone else’s office or in a conference room). Call park numbers are pre-configured for this purpose by your system administrator.

Procedure

Step 1 During an active call, press the more softkey until you see the Park tab. Step 2 Press Park. The LCD screen displays the special ca ll park number at which the

call is stored. If the screen does not display a call park number, the call park feature is not available to you.

Step 3 Make a note of the call park number, then hang up. The call is parked at that

number, allowing you to retrieve it from another phone.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-9

Page 60

Making Telephone Calls

Step 4 T o retr ieve the parked call f rom an y phone in the Cisco CallManager system, dial

Chapter 3 Placing a Call and Other Basic Phone Tasks

the call park number at which the call is parked.

Note You have a limited amount of time to retrieve the parked call before it

reverts to ringing at its original destination. See your system administrator for this time limit.

Related Topics

• Placing a Call, page 3-2

• Answering a Call, page 3-4

• Ending a Call, page 3-4

• Transferring a Call to Another Extension, page 3-7

Answering Calls on Another Extension Using Call Pickup

You can answer an incoming call that is ringing on a telephone extension other than your own by using the call pickup feature.

There are two types of call pickup available on the Cisco IP Phone, as described in these topics:

• How to Pick Up Calls Within Your Group, page 3-11

• How to Pick Up Calls Outside of Your Group, page 3-11

Note Call pickup and group call pickup ar e optional features conf igured by your system

administrator; your phone does not support these features by default.

Related Topics

• Placing a Call, page 3-2

• Answering a Call, page 3-4

• Ending a Call, page 3-4

Cisco IP Phone 7960 and 7940 Series User Guide

3-10

78-10182-08

Page 61

Chapter 3 Placing a Call and Other Basic Phone Tasks

• Putting a Call on Hold, page 3-6

• Redialing the Last Number Dialed, page 3-8

How to Pick Up Calls Within Your Group

Call pickup allows you to pick up incoming calls within your own group. A “group” in this sense is any consolidation of Cisco IP Phone extensions, as defined by your system administrator. For example, your group might contain co-workers in neighboring offices or cubes.

Activate call pickup so that an incoming call del ivered to another extension in your group rings on your extension.

Procedure

Making Telephone Calls

Step 1 Press any available line button on your Cisco IP Phone. Step 2 Press the PickUp softkey. The call now rings on your phone. Step 3 Answer the incoming call.

Tip If there is more than one incoming call involved when you activate call pickup,

the first unanswered call will ring at your phone.

Related Topics

• Storing and Retrieving a Call Using Call Park, page 3-9

• How to Pick Up Calls Outside of Your Group, page 3-11

How to Pick Up Calls Outside of Your Group

Group call pickup allo ws you to pick up i ncoming call s within you r o wn group or in other groups. A “group” might contain co-workers in neighboring offices or cubes.

You must dial the appropriate call pickup group number when using this feature. A call pickup group number is provided to you by your system administrator.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-11

Page 62

Using Speed Dial

Step 1 Press any available line button. Step 2 Press the GPickUp softkey. Step 3 Dial the required call pickup group number. Step 4 Answer the incoming call that is redirected to your phone. Step 5 To pick up a call using a different call pi ckup grou p numbe r, hang up and begin

Tip If there is more than one incoming call involved when you activate group call

Chapter 3 Placing a Call and Other Basic Phone Tasks

Procedure

again at Step 1.

pickup, you receive t he first unanswered call. If there is no unanswered call in the group, or if you dial an invalid group number, you receive a fast busy tone.

Related Topics

• Storing and Retrieving a Call Using Call Park, page 3-9

• How to Pick Up Calls Within Your Group, page 3-11

Using Speed Dial

The buttons to the right of th e LCD screen on your Cisco IP Phone can be used as phone lines or as speed dial buttons, as determined b y your system administrat or. You can assign p hone numb ers and text labels to speed dial buttons using the Cisco CallManager User Options web pages.

Unlike the Fast Dial feature (see the “Using Fast Dials” section on page 5-12), Speed Dial does not require subscribing to or using a service.

Note If you are using one or more Cisco IP Phone 7914 Expansion Modules, you can

access extra speed dial or line buttons. To configure speed dial buttons for your Expansion Module, follow the steps in the procedure below.

Cisco IP Phone 7960 and 7940 Series User Guide

3-12

78-10182-08

Page 63

Chapter 3 Placing a Call and Other Basic Phone Tasks

Follow these instructions to set up your speed dial buttons.

Before You Begin

section on page 1-16.

Procedure

Step 1 From the User Options w eb page, cl ick Add/Update your Speed Dials.

The Add/Update Your Speed Dials page appears. You will see a section for setting speed dials on your phone. If you ha v e one or more Expansi on Modules, you w ill see another section for setting speed dials for each of your Expansion

Step 2 In an available Speed Dial box, enter a phone number or extension that you want

to associate to one of your speed dial buttons.

Using Speed Dial

“Logging In to the User Options Web Pages”

Modules.

Note Be sure to enter the number exactly as you would if you were to call that

number. For example, include an access code such as 9 or the area code, if necessary.

Step 3 In each corresponding Display T e xt box, enter a text label that y ou want displayed

on your phone’ s LCD screen. Y ou can enter a maximum of 30 character s for phone base text and 14 characters for Expansion Module text.

Step 4 Click Update to activate ne w speed dial b uttons and to display the corresponding

text on your phone’s LCD screen. Your LCD screen(s) and lighted buttons will reset.

Step 5 When you are finished, click Return to the Menu or Log Off at the bottom of the

page.

Note If your phone uses Cisco CallManager Extension Mobility, you will need

to log out and back in to the extension mobility service on your phone before the changes take effect.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-13

Page 64

Chapter 3 Placing a Call and Other Basic Phone Tasks

Forwarding Calls to Another Extension

Related Topics

• Using Fast Dials, page 5-12

• Making Telephone Calls, page 3-1

Forwarding Calls to Another Extension

Call forwarding allows you to redirect all incoming calls from your Cisco

IP Phone to another number. Use call forwarding to:

• Send incoming calls to another number where you can answer the calls (for

example, if you are going to be working in an alternate office).

• Send incoming calls directly to voice mail. Your desk phone does not ring

when calls are routed to your voice mail through the call forwarding feature.

Call forwarding can send your calls to another IP Phone or to a traditional analog phone.

If there is no answer at the forwarded number, either a person or voice mail, the call will be sent back to your voice mail system.

Related Topics

• Setting Up Call Forwarding on Your Phone, page 3-14

• Setting Up Call Forwarding When Not at Your Phone, page 3-15

• Canceling Call Forwarding, page 3-16

Setting Up Call Forwarding on Your Phone

Follow these steps to set up call forwarding on your phone.

Procedure

Step 1 Press the CFwdAll softkey. You should hear two beeps. Step 2 Enter the number to which you want to forward all of your calls, exactly as you

would if you were placing a call to that number.

Cisco IP Phone 7960 and 7940 Series User Guide

3-14

78-10182-08

Page 65

Chapter 3 Placing a Call and Other Basic Phone Tasks

For example, enter an access code such as 9 or the area code, if necessary. Your system administrator might restrict the call forw arding featur e to numb ers within your company.

After you enter the number, an animated phone icon with a flashing right arrow appears in the upper-right corner of the LCD screen. The LCD screen also displays a message confirming the number or extension to which your calls are being forwarded.

Step 3 To cancel call forwarding, press the CFwdAll softkey.

Tips

• To set up call forwarding when not at your phone, see the “Setting Up Call

Forwarding When Not at Your Phone” section on page 3-15.

• To use call forwarding to send all of your incoming calls directly to your

voice mail without causing your desk phone to ring, see th e

Forwarding When Not at Your Phone” section on page 3-15.

Forwarding Calls to Another Extension

“Setting Up Call

Related Topics

• Forwarding Calls to Another Extension, page 3-14

• Setting Up Call Forwarding When Not at Your Phone, page 3-15

• Canceling Call Forwarding, page 3-16

Setting Up Call Forwarding When Not at Your Phone

If you are away from your phone, use the Cisco CallManager User Options web pages to set up call forwarding.

Before You Begin

section on page 1-16.

“Logging In to the User Options Web Pages”

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-15

Page 66

Forwarding Calls to Another Extension

Procedure

Step 1 From the User Options web page, click Forward all calls to a di ffer ent number.

The Forward Your Calls page appears.

Step 2 Check the check box next to the line from which you want your incoming calls

forwarded.

Step 3 Choose where to send calls:

• To send calls directly to voice mail, and not ring your phone, choose

Voice

• To send calls to a specific number, choose this number and enter the phone

number or extension in the box provided. Be sure to enter the number exactly as you would if you were to call that

number. For example, enter an access code such as 9 or the area code, if necessary. Your system administrator might restrict the call forwarding feature to numbers within your company.

Chapter 3 Placing a Call and Other Basic Phone Tasks

Mail.

Step 4 Click Update.

Related Topics

• Forwarding Calls to Another Extension, page 3-14

• Setting Up Call Forwarding on Your Phone, page 3-14

• Canceling Call Forwarding, page 3-16

Canceling Call Forwarding

You can cancel call forwarding from either your phone or on the web. To cancel call forwarding from your phone, press the CFwAll softkey. To cancel call forwarding when you are away from your phone, perform the

following procedure.

Cisco IP Phone 7960 and 7940 Series User Guide

3-16

78-10182-08

Page 67

Chapter 3 Placing a Call and Other Basic Phone Tasks

Before You Begin

section on page 1-16.

Procedure

Step 1 From the User Options web page, click Forward all calls to a di ffer ent number.

The Forward Your Calls page appears.

Step 2 Clear the checkbox next to the line for which you want to cancel call forwarding. Step 3 Click Update.

Making Conference Calls

“Logging In to the User Options Web Pages”

Related Topics

• Forwarding Calls to Another Extension, page 3-14

• Setting Up Call Forwarding on Your Phone, page 3-14

• Setting Up Call Forwarding When Not at Your Phone, page 3-15

Making Conference Calls

Your Cisco IP Phone supports conference calls, enabling you to talk with multiple parties at the same time. When you are on a conference call, you can use regular phone features such as Mute, Hold, Transfer, and speakerphone.

This section covers the following topics:

• Placing a Conference Call, page 3-18

• Using Meet-Me Conferences, page 3-18

• Conferencing by Barging in on Established Conversations, page 3-20

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-17

Page 68

Making Conference Calls

Placing a Conference Call

Follow these steps to turn a call into a conference call.

Procedure

Step 1 During a call, press the more softkey and then the Confrn softkey. Doing so

automatically activates a new line and puts the first party on hold.

Step 2 Place a call to another number or extension. Step 3 When the call connects, press Confrn again to add the new party to the conference

call. Repeat these steps to add parties to the conference call. Once the conference call initiator disconnects, no additional parties can be added.

Chapter 3 Placing a Call and Other Basic Phone Tasks

You can drop the last party added by pressing the RmLstC softkey.

Related Topics

• Making Conference Calls, page 3-17

• Using Meet-Me Conferences, page 3-18

• Conferencing by Barging in on Established Conversations, page 3-20

Using Meet-Me Conferences

Your Cisco IP Phone suppo rts Meet-Me conferences. A Me et-Me conference allows other callers to dial into the conference call. A Meet-Me conference requires a special conference number which is pre-configured for this purpose by your system administrator.

This section covers these topics:

• Establishing a Meet-Me Conference, page 3-19

• Joining a Meet-Me Conference, page 3-19

Cisco IP Phone 7960 and 7940 Series User Guide

3-18

78-10182-08

Page 69

Chapter 3 Placing a Call and Other Basic Phone Tasks

Establishing a Meet-Me Conference

Follow these steps to establish a Meet-Me conference call.

Before You Begin

Contact your system administrator for the necessary Meet-Me conference number or numbers.

Procedure

Step 1 Press the more softkey twice to display the Meet-Me tab. Step 2 Press the Meet-Me softkey. Step 3 Dial the Meet-Me conference number. Step 4 Follow the voice instructions to establish the Meet-Me conference.

Making Conference Calls

Related Topics

• Making Conference Calls, page 3-17

• Placing a Conference Call, page 3-18

• Using Meet-Me Conferences, page 3-18

• Conferencing by Barging in on Established Conversations, page 3-20

• Joining a Meet-Me Conference, page 3-19

Joining a Meet-Me Conference

To join a Meet-Me conference, simply dial the Meet-Me conference number provided by the Meet-Me conference initiator. You are connected to the conference once the conference initiator has dialed in and esta blishe d the conference. You do not need to press the Meet-Me softkey on your Cisco

IP Phone.

Related Topics

• Making Conference Calls, page 3-17

• Placing a Conference Call, page 3-18

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-19

Page 70

Chapter 3 Placing a Call and Other Basic Phone Tasks

Making Conference Calls

• Using Meet-Me Conferences, page 3-18

• Conferencing by Barging in on Established Conversations, page 3-20

• Establishing a Meet-Me Conference, page 3-19

Conferencing by Barging in on Established Conversations

The Barge feature lets you add yourself to a call in progress on a shared line appearance.

If the party whose call you bar ged puts the call on hold, puts it in a conference, or transfers it, you are disconnected from th e call.

Note You cannot be on two barged calls at the same time. You cannot put a barged call

on hold and resume the call. You cannot answer a second line while on a barged call.

Procedure

Step 1 Select an active call on one of your shared lines. Step 2 Press the Barge softkey.

The phone creates a conference call and sends a beep tone to all the members of the conference to indicate that the barge occurred and that the conference started.

Step 3 To end the conference, hang up.

When you hang up, the remaining parties receive a disconnect tone, and the original call continues.

Related Topics

• Making Conference Calls, page 3-17

• Placing a Conference Call, page 3-18

• Using Meet-Me Conferences, page 3-18

Cisco IP Phone 7960 and 7940 Series User Guide

3-20

78-10182-08

Page 71

Chapter 3 Placing a Call and Other Basic Phone Tasks

Using Voice Mail

Your phone administrator chooses the voice mail system that your p hone uses. For information on ho w to use your voice mail system, refer to the documentation that came with it. For example, if your administrator conf igured y our phone system to work with Cisco Unity, you would refer to the Cisco Unity documentation about working with your voice mail.

Your Cisco IP Phone indicates that you have one or more new voice mail messages by providing the following cues:

• The red light on your handset remains l it. (This indicator can v ary, depending

on the how the message waiting indicator lamp is configured. See the

“A djusting the Message Waiting Indicator Light” section on page 2-4.)

• A flashing envelope icon displays next to the appropriate line appearance on

the LCD screen.

Using Voice Mail

• A text message on the LCD screen displays.

To set up voice mail, press the Messages button on your Cisco IP Phone and follow the voice instructions. Your system administrator will provide you with a default password. Fo r security reasons, you shoul d change your def ault passw ord as soon as possible.

T o access vo ice mail, press the Messages button and follow the voice instructions.

Related Topics

• Searching and Dialing from the Phone Directory, page 3-23

• Making Telephone Calls, page 3-1

• Using Fast Dials, page 5-12

Cisco IP Phone 7960 and 7940 Series User Guide

3-22

78-10182-08

Page 73

Chapter 3 Placing a Call and Other Basic Phone Tasks

Searching and Dialing from the Phone Directory

Your phone may come configured with a cor porate or local phone di rectory. This directory is searchable and allows you to find and dial phone numbers of colleagues easily.

Follow these steps to view or dial from a directory in your company.

Procedure

Step 1 Press the Directories button. Step 2 Use the Navigation button to select the desired directory from the Directories

menu, then press the Select softkey.

Step 3 Enter search criteria to retrieve a record (see the “Navigating on Your Phone”

section on page 1-11 for information on entering characters into your phone.)

Step 4 To place a call from any directory, use the Navigation button to select the record,

then press the Dial softkey.

Note You might ne ed to use t he EditDial softkey to add digits to the front of

the number. For example, if the call was from an outside, long-distance caller, you might need to add the digits 9-1 to the front of the number. Then, press the Dial softkey.

Step 5 Press the Exit softkey twice to exit the Directory menu.

Related Topics

• Viewing and Dialing from the Phone Logs, p age 3-21

• Making Telephone Calls, page 3-1

• Using Fast Dials, page 5-12

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

3-23

Page 74

Searching and Dialing from the Phone Directory

Chapter 3 Placing a Call and Other Basic Phone Tasks

Cisco IP Phone 7960 and 7940 Series User Guide

3-24

78-10182-08

Page 75

CHAPTER

Logging Into Your Extension from Any Phone Using the Cisco CallManager Extension Mobility Feature

Your system administrator might provide you with a service called Cisco

CallManager Extension Mobility . This service allo ws you to associate your phone number and user profile with any Cisco IP Phone. When you use your Cisco

CallManager Ex tensio n Mobility personal identification number (PIN) to log in to a Cisco you have established from the Cisco CallManager User Options web pages, are associated with that phone.

IP Phone, your assigned telephone number, and the settings that

Note For information about the User Options web pages, see Chapter 1, “Customizing

Your Phone From the User Options Web Pages”.

Cisco CallMana ger Exten sion Mobility is useful to you if you do not routinely conduct business in the same office space every day.

Your system administrator will inform you whether this service is available to you.

If you are logged out of a Cisco IP Phone that has the Cisco CallManager Extension Mobility feature configured for it, you will not be able to make calls, receive calls, or check voice mail messages fr om that phone until you log in. Also, Cisco CallManager Extension Mobility might automatically log you out after a certain amount of time. This time limit is established by your system administrator. Therefore, it is recommended that you log in to your phone at the

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

4-1

Page 76

Chapter 4 Logging Into Your Extension from Any Phone Using the Cisco CallManager Extension Mobility Feature

Logging in to Cisco CallManager Extension Mobility

beginning of every day. If you hear a busy signal after pressing the Messages button or any k ey on the tou ch tone ke y pad, then you must log in befor e using the phone.

Wit h C is co CallManager Extension Mobility, you can be logged into only one phone at a time. If you want to use another phone, you must log out of the first phone.

Your Cisco CallManager Extension Mobility profile does not maintain ring type, contrast settings, and volume settings; configure these settings directly on the Cisco

IP Phone. This section covers the following topics:

• Logging in to Cisc o CallM anager Extension Mobility, page 4-2

• Logging Out of Cisco Ca llManage r Exten sion Mo bility, page 4-4

• Changing Your Cisco CallManager Extension Mobility PIN, page 4-5

Logging in to Cisco CallManager Extension Mobility

To log in to Cisco CallManager Extension Mobil ity, perform the following steps. Your system administrator will provide you with the necessary user ID and personal identification number (PIN).

Tip It is recommended that you log in to your phon e at the be gin ning of the w ork day.

This practice ensures that your user device profile gets loaded on your phone. If you make changes to your profile, the changes will apply wherever you log in.

Procedure

Step 1 Press the Services button on your Cisco IP Phone. Step 2 From the Services menu, use the Navigation button to select the login option for

extension mobility. Then, press the Select softkey.

Cisco IP Phone 7960 and 7940 Series User Guide

4-2

78-10182-08

Page 77

Chapter 4 Logging Into Your Extension from Any Phone Using the Cisco CallManager Extension Mobility Feature

Logging in to Cisco CallManager Extension Mobility

Note Your system administrator chooses the name for your particular

extension mobility service. These options might display on the Settings menu of your phone LCD screen as “extension mobility service,” for example.

Step 3 Enter your user ID. For information on entering letters on your phone, see the

“Navigating on Your Phone” s ection on page 1-11.

Step 4 Use the Navigation button to scroll down to the PIN prompt and enter your PIN. Step 5 Press the submit softkey.

The Cisco IP Phone to which you have logged in now adopts your user profile information, including your speed dials and established services. The phone also becomes associated with your phone number . If you login while the recei ver is of f hook, the changes will not take effect until you hang up.

You may be prompted to select the device profile to use. Use the Navigation button to scroll to the device and click the Select softkey.

Step 6 Press the Exit softkey to return to the previous screen.

Related Topics

• Logging Out of Cisco Ca llManage r Exten sion Mo bility, page 4-4

• Changing Your Cisco CallManager Extension Mobility PIN, page 4-5

• Logging Into Your Extension from Any Phone Using the Cisco CallManager

Extension Mobility Fea ture, page 4-1

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

4-3

Page 78

Chapter 4 Logging Into Your Extension from Any Phone Using the Cisco CallManager Extension Mobility Feature

Logging Out of Cisco CallManager Extension Mobility

When you are ready to log out of Cisco CallManager Extension M ob ility, follow these steps.

Procedure

Step 1 Press the Services button on your phone. Step 2 Use the Navigation button to select the logout option for Cisco CallManager

Extension

Step 3 Press the Select softkey. Step 4 The phone might display “Do you want to log out <your UserID>?” If it does,

select Yes.

Mobility.

Step 5 Press the Exit softkey to return to the previous screen.

Related Topics

• Logging Into Your Extension from Any Phone Using the Cisco CallManager

Extension Mobility Fea ture, page 4-1

• Logging in to Cisc o CallM anager Extension Mobility, page 4-2

• Changing Your Cisco CallManager Extension Mobility PIN, page 4-5

Cisco IP Phone 7960 and 7940 Series User Guide

4-4

78-10182-08

Page 79

Chapter 4 Logging Into Your Extension from Any Phone Using the Cisco CallManager Extension Mobility Feature

Changing Your Cisco CallManager Extension Mobility PIN

To change your Cisco CallManager Extension Mobility PIN, use the Cisco

CallManager User Options web pages:

Note Changing your PIN will effect any service that requires a PIN, such as Personal

Address Book and Personal Fast Dials. If you use these services and chang e your PIN, you must update those services before you can use them.

Before You Begin

section on page 1-16.

“Logging In to the User Options Web Pages”

Procedure

Step 1 From the User Options main menu, click Change your PIN. Step 2 Enter your current PIN and a new PIN in the required fields, then click Update. Step 3 When you are finished, click Return to the Menu or Log Off at the bottom of the

page.

Related Topics

• Logging Into Your Extension from Any Phone Using the Cisco CallManager

Extension Mobility Fea ture, page 4-1

• Logging in to Cisc o CallM anager Extension Mobility, page 4-2

• Logging Out of Cisco Ca llManage r Exten sion Mo bility, page 4-4

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

4-5

Page 80

Chapter 4 Logging Into Your Extension from Any Phone Using the Cisco CallManager Extension Mobility Feature

Changing Your Cisco CallManager Extension Mobility PIN

Cisco IP Phone 7960 and 7940 Series User Guide

4-6

78-10182-08

Page 81

CHAPTER

Managing Your Contacts

Your Cisco IP Phone might su pply s everal different features to help you manage your phone contacts: a personal address book, a Cisco Personal Address Book service, and the Personal Fast Dials service.

The Personal Address Book allows you to store names and numbers of your common contacts. From your Cisco IP Phone, you can use the Personal Address Book service to look up entries, make a selection, and press a softkey to dial the selected number.

With the P ersonal Fast Dials service, you can assign index numbers ( from 1 to 99) for quick dialing from your Cisco IP Phone. You can assign index numbers either to Personal Address Book entries or to directory entries that you add that do not correspond to the address book. You can assign and remove the Personal Fast Dials entries from your phone or the Cisco IP Phone User Options application.

IP phone synchronizer, the

Note The exact names of the Personal Address Book and Personal Fast Dials

services may vary, depending on how your system administrator configured the services.

With the Personal Directory synchronization tool, you can synchronize the Microsoft Windows address book, Microsoft Outlook and/or your Outlook Express address book entries stored on your computer with the Cisco

CallManage r direct ory. These features are optional. Talk to your phone administrator about which

features are available to you.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-1

Page 82

Chapter 5 Managing Your Contacts

Managing Your Personal Address Book

Related Topics

• Managing Your Perso nal Address Bo ok, pag e 5-2

• Dialing a Personal Address Book Entry, page 5-9

• Using the Cisco IP Phone Address Book Synchronizer, page 5-9

• Using Fast Dials, page 5-12

• Using Speed Dial, page 3-12

Managing Your Personal Address Book

You can set up and maintain a personal address book that contains listings for people internal and external to your company. You can also assign Fast Dial codes to personal address book entries and dial those codes in place of phone numbers.

Related Topics

• Creating a New Address Book Entry on the Web , page 5-4

• Searching for or Editing a Personal Address Book Entry on the Web, page 5-5

• Searching Personal Address Book Entries on Your Phone, page 5-6

• Editing a Personal Address Book Entry on Your Phone, page 5-7

• Deleting an Address Book Entry on the Web, page 5-8

Subscribing to Personal Address Book

The Personal Address Book service allows you to look up address book entries and to dial a chosen number by pressing a softkey on your phone.

Before You Begin

section on page 1-16.

“Logging In to the User Options Web Pages”

Cisco IP Phone 7960 and 7940 Series User Guide

5-2

78-10182-08

Page 83

Chapter 5 Managing Your Contacts

Procedure

Step 1 From the User Options Menu window in the Cisco IP Phone User Options

application, choose a device to configure, such as your primary phone.

Step 2 Click the Configure your Cisco IP Phone Services link.

The Cisco IP Phone Services window displays.

Step 3 Choose the service as named by your system administrator; for example, My

Address Book.

Step 4 Click Continue. Step 5 Enter the appropriate service information. An asterisk indicates required fields.

For a description of each field, click the Description link next to the field.

Step 6 Click Subscribe.

Managing Your Personal Address Book

Related Topics

• Creating a New Address Book Entry on the Web , page 5-4

• Searching for or Editing a Personal Address Book Entry on the Web, page 5-5

• Searching Personal Address Book Entries on Your Phone, page 5-6

• Editing a Personal Address Book Entry on Your Phone, page 5-7

• Deleting an Address Book Entry on the Web, page 5-8

• Managing Your Perso nal Address Bo ok, pag e 5-2

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-3

Page 84

Chapter 5 Managing Your Contacts

Managing Your Personal Address Book

Creating a New Address Book Entry on the Web

Follow these steps to create a new address book entry.

Before You Begin

section on page 1-16.

Procedure

Step 1 From the User Options web page, click Configure y our Cisco Personal Address

Book. The Find/List Personal Address Book Entries page appears.

“Logging In to the User Options Web Pages”

Note You can add entries manually or use a synchronizer application to

automatically import entries from your Microsoft Outlook address book. To obtain the synchronizer, contact your system administrator.

Step 2 Click Add a New Entry.

The Address Book Entry window appears.

Step 3 Enter information in the desired fields and click Insert. Step 4 When you are finished:

• Click Return to Search, Fast D i als , or Add a New Entry to continue

working in the Find/List Address Book Entries page.

• To exit, click Return to the Menu or Log Off at the bottom of the page.

Related Topics

• Subscribing to Personal Address Book, page 5-2

• Searching for or Editing a Personal Address Book Entry on the Web, page 5-5

• Searching Personal Address Book Entries on Your Phone, page 5-6

• Editing a Personal Address Book Entry on Your Phone, page 5-7

Cisco IP Phone 7960 and 7940 Series User Guide

5-4

78-10182-08

Page 85

Chapter 5 Managing Your Contacts

Managing Your Personal Address Book

• Deleting an Address Book Entry on the Web, page 5-8

• Managing Your Perso nal Address Bo ok, pag e 5-2

Searching for or Editing a Personal Address Book Entry on the Web

Follow these steps to search for an address book entry. A fter you find the entry, you can modify or delete the entry, if necessary.

Before You Begin

section on page 1-16.

“Logging In to the User Options Web Pages”

Procedure

Step 1 From the User Options web page, click Configure y our Cisco Personal Address

Book. The Find/List Personal Address Book Entries page appears.

Step 2 Enter the name you that want to f ind by First Name, Last Name, or Nickn ame and

click Find; you can enter partial or complete information in any search field (wildcard symbols such as * are implicit and do not need to be entered.)

If you want to view all entries in your address book, click Find without entering a name.

Step 3 Click on any portion of the person’s name to display the complete entry or enter

more search information to further refine your search.

Step 4 If you want to edit any of t he informatio n, mak e the ne cessary ch anges, and click

Update.

Related Topics

• Creating a New Address Book Entry on the Web , page 5-4

• Subscribing to Personal Address Book, page 5-2

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-5

Page 86

Chapter 5 Managing Your Contacts

Managing Your Personal Address Book

• Searching Personal Address Book Entries on Your Phone, page 5-6

• Editing a Personal Address Book Entry on Your Phone, page 5-7

• Deleting an Address Book Entry on the Web, page 5-8

• Managing Your Perso nal Address Bo ok, pag e 5-2

Searching Personal Address Book Entries on Your Phone

Use the following procedure to find a personal address book entry.

Procedure

Step 1 Press the services but t o n .

The phone displays the services that have been configured for your phone.

Step 2 Use the navigation button to highlight the option that corresponds to the My

Address Book service and press the Select softkey.

Tip The exact service name may vary, depending on how your system

administrator configured the service.

Step 3 Perform one of the following actions:

• T o display a specific name, enter the name using your phone keypad and press

the Submit softkey. All names that match your search criteria will display.

• To display all your address book entries, press the Submit softkey.

Step 4 Using the navigation b utton, highlight the entry that you w ant and press the Select

softkey.

Related Topics

• Creating a New Address Book Entry on the Web , page 5-4

• Searching for or Editing a Personal Address Book Entry on the Web, page 5-5

• Subscribing to Personal Address Book, page 5-2

• Editing a Personal Address Book Entry on Your Phone, page 5-7

Cisco IP Phone 7960 and 7940 Series User Guide

5-6

78-10182-08

Page 87

Chapter 5 Managing Your Contacts

Managing Your Personal Address Book

• Deleting an Address Book Entry on the Web, page 5-8

• Managing Your Perso nal Address Bo ok, pag e 5-2

Editing a Personal Address Book Entry on Your Phone

Use the following procedure to edit a Personal Address Book entry.

Procedure

Step 1 Find the entry that you want to edit as described in “Editing a Personal Address

Book Entry on Your Phone” section on page 5-7.

Step 2 Press the Edit softkey.

The phone displays the Personal Address Book information for that entry.

Step 3 Perform one of the following actions:

• To edit the first name, last name, or nickname for this entry, press the Name

softkey.

• To edit the home, work, or mobile numbers, press the Phone softkey.

Step 4 Make your changes and press the Submit softkey.

The phone displays a message that your change is successful.

Step 5 Press the OK softkey.

Related Topics

• Creating a New Address Book Entry on the Web , page 5-4

• Searching for or Editing a Personal Address Book Entry on the Web, page 5-5

• Searching Personal Address Book Entries on Your Phone, page 5-6

• Subscribing to Personal Address Book, page 5-2

• Deleting an Address Book Entry on the Web, page 5-8

• Managing Your Perso nal Address Bo ok, pag e 5-2

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-7

Page 88

Managing Your Personal Address Book

Deleting an Address Book Entry on the Web

Follow these steps to delete an address book entry.

Before You Begin

section on page 1-16.

Procedure

Step 1 Find the entries you want to delete (see the “Searching for or Editing a Personal

Address Book Entry on the Web” section on page 5-5.)

Step 2 To delete an individual entry, check the checkbox next to the entry.

“Logging In to the User Options Web Pages”

Chapter 5 Managing Your Contacts

To delete all entries displayed as a result of your search, check the checkbox in the heading bar above the individual entries. Doing so automatically selects each of the displayed entries.

Step 3 Click Delete Selected.

Related Topics

• Creating a New Address Book Entry on the Web , page 5-4

• Searching for or Editing a Personal Address Book Entry on the Web, page 5-5

• Searching Personal Address Book Entries on Your Phone, page 5-6

• Editing a Personal Address Book Entry on Your Phone, page 5-7

• Subscribing to Personal Address Book, page 5-2

• Managing Your Perso nal Address Bo ok, pag e 5-2

Cisco IP Phone 7960 and 7940 Series User Guide

5-8

78-10182-08

Page 89

Chapter 5 Managing Your Contacts

Dialing a Personal Address Book Entry

Use the following procedure to dial a Personal Address Book entry.

Procedure

Step 1 Find the entry that you want to dial as described in “Editing a Personal Address

Book Entry on Your Phone” section on page 5-7.

Step 2 Use the navigation b utton to choose the directory number that you wa nt to dial and

press the Dial softkey.

Related Topics

• Creating a New Address Book Entry on the Web , page 5-4

• Managing Your Perso nal Address Bo ok, pag e 5-2

Using the Cisco IP Phone Address Book Synchronizer

You can synchronize your Microsoft Outlook and/or your Outlook Express address book entries with the directory in Cisco Cisco

IP Phone Address Book Synchronizer.

• Installing the Cisco IP Phone Address Book Synchronizer, page 5-9

• Configuring the Cisco IP Phone Address Book Synchronizer, page 5-11

Installing the Cisco IP Phone Address Book Synchronizer

To install Cisco IP Phone Address Book Synchronizer, perform the following steps.

CallManager using the

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-9

Page 90

Using the Cisco IP Phone Address Book Synchronizer

Before You Begin

You need to get the Cisco IP Phone Address Book Synchronizer installer file from your system administrator.

Procedure

Step 1 Double-click the TabSyncInstall.exe file provided by your system administrator.

The Welcome to Cisco IP Phone Address Book Synchronizer window displays.

Step 2 Click Next.

The License Agreement window displays.

Step 3 Read the license agreement information, and click Yes to accept.

The Choose Destination Location window displays.

Step 4 Choose the directory in which you want to install the application and click Next.

Chapter 5 Managing Your Contacts

The Start Copying Files window displays.

Step 5 Verify that you have chosen the correct directory, and click Next.

The installation wizard installs the application to your computer. When the installation is complete, the InstallShield Wizard Complete window displays.

Step 6 Click Finish.

For information on configuring the Cisco IP Phone Address Book Synchronizer, see

“Configuring the Cisco IP Phone Address Book Synchronizer” section on

page 5-11.

Related Topics

• Configuring the Cisco IP Phone Address Book Synchronizer, page 5-11

• Using the Cisco IP Phone Address Book Synchronizer, page 5-9

Cisco IP Phone 7960 and 7940 Series User Guide

5-10

78-10182-08

Page 91

Chapter 5 Managing Your Contacts

Using the Cisco IP Phone Address Book Synchronizer

Configuring the Cisco IP Phone Address Book Synchronizer

Use the following steps to configure the Cisco IP Phone Address Book Synchronizer and to synchronize your address book.

Procedure

Step 1 Open the Cisco IP Phone Address Book Synchronizer.

If you accepted the default installation directory , you can open the application by choosing Start > Programs > Cisco > IP

Step 2 To configure user information, click the Password button.

The Cisco IP Phone User window displays.

Step 3 Enter the Cisco IP phone user name and password and click OK.

Phone Address Synchronizer.

Step 4 To configure synchronization rules, click the Rules Options button. Step 5 Choose the synchronization method that you want to use and click OK. Step 6 To configure Cisco CallManager information, click the CCM Server butto n.

The Configure Cisco CallManager Web Server window displays.

Step 7 Enter the IP address or host name of the Cisco CallManager and click OK.

If you do not have this information, contact your system administrator.

Step 8 Click the Password button.

The Cisco IP Phone User window displays.

Step 9 Enter your user identification and passw ord fo r the Cisco IP Phone User Options

application.

Step 10 To start the directory synchronization process, click the Synchronize button.

The Synchronization Status window provides information on the status of the address book synchronization. If you chose the user intervention for duplicate entries rule and you have duplicate address book entries, the Duplicate S election window displays. Choose the entry that you want to include in your Personal Address Book and click OK.

Step 11 When synchronization completes, click Exit to close the Cisco IP Phone Address

Book Synchronizer.

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-11

Page 92

Using Fast Dials

Related Topics

• Using the Cisco IP Phone Address Book Synchronizer, page 5-9

• Installing the Cisco IP Phone Address Book Synchronizer, page 5-9

Using Fast Dials

With Personal Fast Dials, you can assign index numbers (from 1 to 99) to phone numbers for quick dialing from your Cisco IP phone.

To use Personal Fast Dials, you must subscribe to the Fast Dials service and use either your phone or the USer Options web pages to assign fast dial numbers.

Related Topics

• Subscribing to Personal Fast Dials, page 5-12

Chapter 5 Managing Your Contacts

• Assigning Fast Dial Codes to Phone Numbers on the Web, page 5-13

• Removing Personal Fast Dials Entries on the Web, page 5-15

• Creating a Personal Fast Dials Entry for a Number in Your Personal Address

Book on Your Phone, page 5-16

• Creating a Personal Fast Dial Entry for a Non-Address Book Direct ory

Number on Your Phone , page 5-17

• Removing a Personal Fast Dials Entry on Your Phone, page 5-19

• Dialing a Personal Fast Dials Entry, page 5-20

Subscribing to Personal Fast Dials

To subscribe to the Personal Fast Dials service, perform the following steps.

Before You Begin

section on page 1-16.

“Logging In to the User Options Web Pages”

Cisco IP Phone 7960 and 7940 Series User Guide

5-12

78-10182-08

Page 93

Chapter 5 Managing Your Contacts

Procedure

Step 1 From the User Options Menu window in the Cisco IP Phone User Options

application, choose a device to configure, such as your primary phone.

Step 2 Click the Configure your Cisco IP Phone Services link.

The Cisco IP Phone Services window displays.

Step 3 Choose the service as named by your system administrator; for example My Fast

Dials and click Continue.

Step 4 Enter the appropriate service information. An asterisk indicates required fields.

For a description of each field, click the Description link next to the field.

Step 5 Click Subscribe.

Using Fast Dials

Related Topics

• Subscribing to Personal Fast Dials, page 5-12

• Creating a Personal Fast Dials Entry for a Number in Your Personal Address

Book on Your Phone, page 5-16

• Creating a Personal Fast Dial Entry for a Non-Address Book Direct ory

Number on Your Phone , page 5-17

• Removing a Personal Fast Dials Entry on Your Phone, page 5-19

Creating a Personal Fast Dials Entry for a Number in Your Personal Address Book on Your Phone

Use the following procedure to create a Personal Fast Dials entry for a number in your Personal Address Book. For informat ion on creating an entry for a directory number that is not in your address book, see the

Entry for a Non-Address Book Directory Number on Your Phone” section on page 5-17.

“Creating a Personal Fast Dial

Cisco IP Phone 7960 and 7940 Series User Guide

5-16

78-10182-08

Page 97

Chapter 5 Managing Your Contacts

Procedure

Step 1 Find the address book entry for which you want to create a fast dial as described

“Editing a Personal Address Book Entry on Your Phone” section on page 5-7.

Step 2 Use the navigation button to highlight the appropriate entry and press the Select

softkey.

Step 3 Press the FastDial softkey. Step 4 Use the navigation button to highlight the directory number that you want to

assign to a fast dial index (home, work, or mobile) and press the Select softkey.

Step 5 Use the navigation butt on t o choose a f a st-dial i ndex and press the Select softkey.

A message displays that the Fast Dials entry has been created.

Step 6 Press the OK softkey.

Using Fast Dials

Related Topics

• Subscribing to Personal Fast Dials, page 5-12

• Assigning Fast Dial Codes to Phone Numbers on the Web, page 5-13

• Removing Personal Fast Dials Entries on the Web, page 5-15

• Creating a Personal Fast Dial Entry for a Non-Address Book Direct ory

Number on Your Phone , page 5-17

• Removing a Personal Fast Dials Entry on Your Phone, page 5-19

• Dialing a Personal Fast Dials Entry, page 5-20

Creating a Personal Fast Dial Entry for a Non-Address Book Directory Number on Your Phone

Use the following procedure to create a Personal Fast Dials entry for a directory number that is not in your Personal Address Book. F or information on cr eating an entry for a number in your address book, see the

Entry for a Number in Your Personal Address Book on Your Phone” section on page 5-16.

“Creating a Personal Fast Dials

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-17

Page 98

Using Fast Dials

Step 1 From your Cisco IP Phone, press the services button.

Step 2 Use the navigation button to highlight the option that corresponds to the My Fast

Step 3 Press the Assign softkey.

Step 4 Use the navigation button to highlight a fast-dial index and press the Select

Chapter 5 Managing Your Contacts

Procedure

The phone displays the services that have been configured for your phone.

Dials service and press the Select softkey.

Tip Remember, the exact service name may vary, depending on how your

system administrator configured the service.

A message displays requesting you to choose an index to assign.

softkey.

Step 5 Enter a directory nu mber and press the Submit softkey.

A message displays that the Fast Dials entry has been created.

Step 6 Press the OK softkey.

Related Topics

• Subscribing to Personal Fast Dials, page 5-12

• Assigning Fast Dial Codes to Phone Numbers on the Web, page 5-13

• Creating a Personal Fast Dials Entry for a Number in Your Personal Address

Book on Your Phone, page 5-16

• Removing a Personal Fast Dials Entry on Your Phone, page 5-19

• Dialing a Personal Fast Dials Entry, page 5-20

Cisco IP Phone 7960 and 7940 Series User Guide

5-18

78-10182-08

Page 99

Chapter 5 Managing Your Contacts

Removing a Personal Fast Dials Entry on Your Phone

Use the following procedure to remove a Personal Fast Dials entry.

Procedure

Step 1 From your Cisco IP Phone, press the services button.

The phone displays the services that have been configured for your phone.

Step 2 Use the navigation button to highlight the option that corresponds to the My Fast

Dials service and press the Select softkey.

Step 3 Press the Remove softkey.

A message prompts you to choose an index to remove.

Step 4 Use the navigation butto n to highlight the index that yo u want to remove and press

the Select softkey.

Using Fast Dials

A message displays indicating that the entry has been removed.

Step 5 Click the OK softkey.

Related Topics

• Subscribing to Personal Fast Dials, page 5-12

• Creating a Personal Fast Dials Entry for a Number in Your Personal Address

Book on Your Phone, page 5-16

• Creating a Personal Fast Dial Entry for a Non-Address Book Direct ory

Number on Your Phone , page 5-17

• Removing a Personal Fast Dials Entry on Your Phone, page 5-19

• Dialing a Personal Fast Dials Entry, page 5-20

78-10182-08

Cisco IP Phone 7960 and 7940 Series User Guide

5-19

Page 100

Using Fast Dials

Dialing a Personal Fast Dials Entry

Use the following procedure to dial a number using the Personal Fast Dials service.

Before You Begin

Before you can use the Fast Dial feature on your Cisco IP Phone, you must subscribe to the Fast Dial service. For information on subscribing to services, refer to the

Procedure

Step 1 From your Cisco IP Phone, press the services button.

The phone displays the services that have been configured for your phone.

“Establishing Cisco IP Phone Services” section on page 1-18

Chapter 5 Managing Your Contacts

Step 2 Use the navigation button to highlight the option that corresponds to the My Fast

Dials service and press the Select softkey.

Tip Remember, the exact service name may vary, depending on how your

system administrator configured the service.

A screen displays your Personal Fast Dials entrie s.

Step 3 Use the navigation butto n to choose a f a st dial number and press the Dial softkey.

Related Topics

• Subscribing to Personal Fast Dials, page 5-12

• Assigning Fast Dial Codes to Phone Numbers on the Web, page 5-13

• Creating a Personal Fast Dials Entry for a Number in Your Personal Address

Book on Your Phone, page 5-16

• Creating a Personal Fast Dial Entry for a Non-Address Book Direct ory

Number on Your Phone , page 5-17

• Dialing a Personal Fast Dials Entry, page 5-20

Cisco IP Phone 7960 and 7940 Series User Guide

5-20

78-10182-08