Cisco Systems 400 User Manual

Quick Start Guide

FASTHUB 400 10/100 SERIES

CABLING AND START UP

S
E
R

IE
S

1

TAKE OUT WHAT YOU NEED

2

CONNECT THE HUB TO OTHER NETWORK DEVICES

3

ASSIGN IP INFORMATION TO THE HUB

4

DISPLAY THE WEB-BASED HUB MANAGER

Take Out What You Need

FastHub 400 10/100 series hub

1
0
B

a
s
e

T
/
1
0

0
B
a

s
e
T

(12- or 24-port model)

FastHub 400 10/100 Series Installation
and Configuration Guide

RJ-45-to-RJ-45 rollover console cable
(FastHub 412M and FastHub 424M
models only)

RJ-45-to-DB-9 console-to-PC adapter

1

(FastHub 412M and FastHub 424M
models only)

x

R
P
S

1
x

2
x

3
x

4
x

5
x

1
0
1
00

6
x

7

x

8
x

9
x

1
0
x

1
1
x

1
2
x

1

M
O

D
E

2

Quick Start
Guide

R
P
S

10
10

M
O

D
E

Installation

Configuration

Guide

1
0
B
a
s

e
T
/
1

0
0
B

a
s
e

T
x

1
x

2
x

3
x

4
x

5
x

0

6
x

7
x

8
x

9
x

1
0
x

1
1
x

1
2
x

1
3
x

1
4
x

1
5
x

1
6
x

1
7
x

1
8
x

1
9
x

2
0
x

2
1
x

2
2
x

2
3
x

2
4
x

2
4

Black AC power cable

Rack-mount kit

Rubber feet

If any item is missing or damaged, contact your Cisco representative or reseller for support.

Note: You need to supply Category 3, 4, or 5 straight-through or crossover cables to connect
to Ethernet devices.

Connect the Hub to Other Network Devices

R

P

S

1x

2x

3x

4x

1

0

1

0
0

M

O

D

E

5x

6x

7x

8x

9x

10BaseT/100BaseTX
network port (RJ-45)

Maximum cable length:

328 ft (100 m)

10BaseT or

100BaseTX port

(RJ-45)

Ethernet cable

(not supplied)

Note: Use a straight-through cable to
connect two ports when one of the ports is
designated with an X. Use a crossover cable
to connect two ports when both ports are
designated with an X.

Connect the Hub to Servers,
Routers, and Workstations

• Connect a Category 3, 4, or 5
straight-through cable to any 10/100
port on the hub and to a 10BaseT port
on the workstation, server, or router.

10BaseT/100BaseTx

10x

11x

12x

13x

14x

15x

16x

17x

18x

19x

20x

21x

22x

23x

24x

24

2

Connect the Hub to Switches
and Other Hubs

• Connect a Category 3, 4, or 5 crossover
cable to any 10/100 port on the hub and
to a 10BaseT port on the target switch
or hub.

• Connect a Category 5 crossover cable to
any 10/100 port on the hub and to a
100BaseTX port on the target switch or
hub.

• Connect a Category 5 straight-through
cable to any 10/100 port on the hub and
to a 100BaseTX port on the
workstation, server, or router.

Connect the Hub to Other Network Devices
(continued)

D

C

IN

P

U

T

S
F

O

R

R

E

M

O

T

E

P

O

W

E

R

S

U
P

P

L

Y

UP

R

A

T

IN

G
1
0

0-12

7
/ 2

0

0

-2
4
0

V

2

A

/1A

50

/ 6

0
H

R

A

T

IN

G
1
0

0

-12
7
/ 2

00

-2
4
0

V

2

A

/1

A
5

0

/ 6

0
H

R

A

T

IN

G
1
0

0

-12
7
/ 2

0

0

-2
4
0

V

2

A

/1

A
5

0

/ 6

0 H

CONSOLE

~

z

CONSOLE

~
z

CONSOLE

~
z

S

P
E

C

I
F

IE

D

IN

M

A

N

U

A

L

+

5

V

@

6

A

,
+

1

2

V

@

1

A

DC INPUT

1

0
/1

0

0

B

A

S

E

­T

X

DOWN

S

T

A

T
D

U

P

10

0

MEDIA MODULE

D

C

IN

P

U

T

S
F

O

R

R

E

M

O

T

E

P

O

W

E

R

1

S

0

U

/
1

P

0

P

0

L

B

Y

A

S

E

­T

UP

DOWN

UP

DOWN

X

S

P
E

C

IF

IE

D

IN

M

A

N

U

A

L

+

5

V

@

6

A

,
+

1

2

V

@

1

A

DC INPUT

ST

A

T

D
U

P

10

0

MEDIA MODULE

D

C

IN

P

U

T

S

F

O

R

R

E

M

O

T

E

P

O

W

E

R

S

U

1

P

0

P

0

B

L

Y

A
S

E

­F

X

S

P
E

C

IF

IE

D

IN

M

A

N

U

A

L

+

5

V

@

6

A

,
+

1

2

V

@

1

A

DC INPUT

LIN

K

DU

P

TX

R
X

MEDIA MODULE

3

(Optional) Install the
Switched Uplink Module in
the Hub

Power off the hub.

1

Remove and set aside the screws

2

attaching the faceplate to expansion slot
on the hub. The screws will be used later
in Step 6.

Remove the faceplate from the hub and

3

store it for future use.

Slide the module into the slot

4

card-guides until you feel it touch the
back of the hub.

Push the module firmly until it snaps

5

into place and is firmly seated.

Insert and tighten the screws on the

6

module faceplate.

Power on the hub.

7

(Optional) Connect to the
Switched Uplink Module
Port

Insert a connector according to the type of
module (10/100 or 100BaseFX), as follows:

• 10BaseT/100BaseTX connector—Insert

the connector until it snaps into place in the
module port.

Note: Use a straight-through cable to
connect two ports when one of the ports is
designated with an X. Use a crossover cable
to connect two ports when both ports are
designated with an X.

• 100BaseFX SC connector—Remove the
rubber plugs from the fiber-optic port
on the module and store them for future
use. Insert the connector in the
fiber-optic module port.

Connect the Hub to Other Network Devices
(continued)

D
C

I

N

P

U

T
S

F

O

R
R

E

M

O

T

E

P

O

W

E

R

1

S

0

U

/1

P

0

P

0

B

L
Y

A

S

E

-T
X

S

P

E

C

IF

IE

D

IN

M

A

N
U

A

L
+
5

V

@

6
A

,

+
1

2

V

@

1

A

DC INPUT

STATDUP 100

MEDIA MODULE

Power outlet

100-127 / 200-240 V~

2A /1A 50 / 60 Hz

RJ-45-to-RJ-45

rollover console cable

(supplied)

RATING

CONSOLE

UP

DOWN

Console port

(RJ-45)

RJ-45-to-DB-9

adapter (supplied)

4

(Optional) Connect the
Console Cable

Make sure console port settings of the

1

FastHub 400M model match the
settings of the terminal, PC, or laptop.
The default settings of the hub console
port are 9600 baud, 8 data bits,
1 stop bit, no parity, and no flow
control.

Connect the rollover console cable to

2

the CONSOLE port on the hub.

Connect the other end of the rollover

3

cable to your terminal, PC, or laptop
(if necessary, use an appropriate
adapter, such as the supplied
RJ-45-to-DB-9 adapter).

From your terminal, PC, or laptop, start

4

the terminal emulation program.

Power Up the Hub

Connect one end of the power cord to

1

the hub and the other end to a power
source.

Note: You can use the internal power
supply and the Cisco 600W AC Redundant
Power System (RPS). Attach only the Cisco
RPS (model PWR600-AC-RPS) to the RPS
receptacle.

Wait approximately 2 minutes for the

2

hub to complete its power-on self-test
(POST).

After POST completes, the Continue
with configuration dialog? prompt
appears on the management station.
You can then follow the prompts to
assign IP information to the hub.

(Optional) Assign IP Information to the Hub

The hub is designed to operate with little or
no user intervention. In most cases, you can
use it with its default settings.

Assign IP information to the FastHub 400M
model so that you can use the FastHub 400
series Hub Manager web-based interface
and so that the hub can communicate with
local routers and the intranet.

Contact your system administrator for the
hub IP information, and record it here.

Hub IP address:

Enter the IP address of the default

4

gateway (for example: 10.1.105.254):

Enter IP default gateway: 10.1.105.254

The following information is displayed:

The following configuration command
script was created:
ip address 10.1.105.20 255.255.255.0
ip default-gateway 10.1.105.254
!
end

Enter Y:

5

Use this configuration? Y

Subnet mask:

The following information is displayed:

Default gateway:

Building configuration...

From the terminal or PC, enter Y:

5

1

Continue with configuration dialog? Y

Enter the IP address (for example:

2

10.1.105.20):

Enter IP address: 10.1.105.20

Enter the subnet mask (IP netmask)

3

(for example: 255.255.255.0):

Enter IP netmask: 255.255.255.0

Use the enabled mode ‘configuration’
command to modify this configuration.

Press RETURN to get started.

Press Return.

6

Exit from the terminal session.

7

You can now display the FastHub 400 series
Hub Manager.

(Optional) Display the FastHub 400 Series
Hub Manager

If you have the IP address to the hub, you can display the FastHub 400 series Hub Manager
from your intranet. You can use the FastHub 400 series Hub Manager to configure and monitor
the hub.

Start Netscape Communicator (4.03 or higher) or Microsoft Internet Explorer

1

(4.01 or higher). Make sure that Java and JavaScript are enabled.

Enter the IP address of the hub in the URL field if you are using Communicator

2

(the Address field if you are using Internet Explorer).

The FastHub 400 series Hub Manager Home page appears.

Click Apply after
making changes
on a page.

Click Revert
to discard
unapplied
changes on
a page.

Click Help for
procedures and
detailed field
descriptions.

Click the Mode
button to change
the mode that
the LEDs display
for the fixed
10/100 ports.

HOME PORT GROUP IP SNMP CDP SYSTEM

Click to display the settings, status, and
statistics of an installed 10BaseT/100BaseTX
or 100BaseFX switched uplink module.

Click these topics to move from page
to page. On Netscape Communicator
only, when the cursor is above a topic,
a pop-up briefly describes the options
on that particular page.

Click a port to display its
settings, status, and statistics.

Shows when another hub is connected to a
stacking connector on the hub rear panel.

Note: The FastHub 400 10/100 Series Installation and Configuration Guide and the
FastHub 400 10/100 series Hub Manager online help provide complete information about the
web console and describe how to configure and monitor the hub.

6

Corporate Headquarters

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]

800 553-NETS (6387)

Fax: [phone]

European Headquarters

Cisco Systems Europe s.a.r.l.
Parc Evolic, Batiment L1/L2
16 Avenue du Quebec
Villebon, BP 706
91961 Courtaboeuf Cedex
France
http://www-europe.cisco.com
Tel: [phone]
Fax: [phone]

Americas
Headquarters

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
Fax: [phone]

Asia Headquarters

Nihon Cisco Systems K.K.
Fuji Building, 9th Floor
3-2-3 Marunouchi
Chiyoda-ku, Tokyo 100
Japan
http://www.cisco.com
Tel: [phone]
Fax: [phone]

Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the

Cisco Connection Online Web site at http://www.cisco.com.

Argentina • Australia • Austria • Belgium • Brazil • Canada • Chile • China (PRC) • Colombia • Costa Rica • Czech Republic • Denmark

England

• France • Germany • Greece • Hungary • India • Indonesia • Ireland • Israel • Italy • Japan • Korea • Luxembourg • Malaysia

• The Netherlands • New Zealand • Norway • Peru • Philippines • Poland • Portugal • Russia • Saudi Arabia • Scotland • Singapore

Mexico

South Africa

AccessPath, Any to Any, AtmDirector, the CCIE logo, CD-PAC, Centri, the Cisco Capital logo, CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the
Cisco Powered Network logo, the Cisco Press logo, the Cisco Technologies logo, ClickStart, ControlStream, DAGAZ, Fast Step, FireRunner, IGX, IOS, JumpStart, Kernel Proxy,
LoopRunner, MGX, Natural Network Viewer, NetRanger, NetRanger Director, NetRanger Sensor, NetSonar, Packet, PIX, Point and Click Internetworking, Policy Builder, Precept,
RouteStream, Secure Script, SMARTnet, SpeedRunner, Stratm, StreamView, The Cell, TrafficDirector, TransPath, ViewRunner, VirtualStream, VlanDirector, Workgroup Director, and
Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, The Internet Economy, and The New Internet Economy
are service marks; and BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, Enterprise/Solver, EtherChannel, FastHub, ForeSight,
FragmentFree, IP/TV, IPX, LightStream, LightSwitch, MICA, Phase/IP, StrataSphere, StrataView Plus, and SwitchProbe are registered trademarks of Cisco Systems, Inc. in t he U.S. and
certain other countries. All other trademarks mentioned in this document are the property of their respective owners. (9811R)

• Spain • Sweden • Switzerland • Taiwan, ROC • Thailand • Tur key • United Arab Emirates • United States • Venezuela

78-5566-01