Christie LW401, LW551i, LWU421, LX601i User Manual

LX501/LW401/LWU421/

LX601i/LW551i/LWU501i

User Manual-Network Guide

020-000475-02

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Projector

LX501/LW401/LWU421/ LX601i/LW551i/LWU501i User Manual

Network Guide

User's Manual (detailed) - Network Guide

Thank you for purchasing this product.

This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product.

WARNING

►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

Features

This projector has the network function that brings you the following main features.

ü Network Presentation : allows the projector to project computer images transmitted

through a network. (

ü Web Control : allows you to monitor and control the projector through a network from a

computer. (

ü My Image : allows the projector to store up to four still images and project them. ( ü Messenger : allows the projector to display text sent from a computer through a network.

&51)

(

ü Network Bridge : allows you to control an external device through the projector from a

computer. (

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted

without express written consent.

Trademark acknowledgment

• Microsoft trademarks of Microsoft Corporation in the U.S. and/or other countries.

• Adobe

• Pentium

• JavaScript

• HDMI registered trademarks of HDMI Licensing LLC in the United States and other countries.

• Crestron trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and

other countries.

• Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

All other trademarks are the properties of their respective owners.

Network Guide 020-000475-02 Rev. 1 (06-2012)

&16)

&52)

• The information in this manual is subject to change without notice.

, Internet Explorer®, Windows®, Windows Vista® and Aero® are registered

and Flash® are registered trademarks of Adobe Systems Incorporated.

is a registered trademark of Intel Corporation.

is a registered trademark of Sun Microsystems, Inc.

, the HDMI logo and High-Denition Multimedia Interface are trademarks or

, Crestron e-Control®, e-Control®, Crestron RoomView® and RoomViewTM are

&15)

&50)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Contents

Caution .......................................................................................... 4

1. Connection to the network ...................................................... 5

1.1 System requirements ................................................................................. 5

1.1.1 Required equipment preparation ..................................................................................... 5

1.1.2 Hardware and software requirement for computer .......................................................... 5

1.2 Quick connection . ....................................................................................... 6

1.3 Manual network connection setting - Wired LAN -. ..................................... 7

1.3.1 Equipments connection .................................................................................................... 7

1.3.2 Network settings .............................................................................................................. 7

1.3.3 “Internet Option” setting ................................................................................................. 10

1.4 Manual network connection setting - Wireless LAN - ............................... 11

1.4.1 Preparation for wireless LAN connection ....................................................................... 11

1.4.2 Wireless LAN connection set up .................................................................................... 12

2. Network Presentation ............................................................. 15

3. Web Control ............................................................................ 16

3.1 Projector Web Control ............................................................................... 17

3.1.1 Logon ............................................................................................................................. 17

3.1.2 Network Information ....................................................................................................... 18

3.1.3 Network Settings ............................................................................................................ 19

3.1.4 Port Settings .................................................................................................................. 22

3.1.5 Mail Settings .................................................................................................................. 24

3.1.6 Alert Settings .................................................................................................................. 25

3.1.7 Schedule Settings .......................................................................................................... 27

3.1.8 Date/Time Settings ......................................................................................................... 30

3.1.9 Security Settings ............................................................................................................ 32

3.1.10 Projector Control .......................................................................................................... 33

3.1.11 Remote Control ............................................................................................................ 39

3.1.12 Projector Status ........................................................................................................... 41

3.1.13 Network Restart ........................................................................................................... 41

3.2 Crestron e-Control® .................................................................................. 42

3.2.1 Main window .................................................................................................................... 43

3.2.2 Tools window ................................................................................................................... 45

3.2.3 Info window ..................................................................................................................... 47

3.2.4 Help Desk window ........................................................................................................... 48

3.2.5 Emergency Alert .............................................................................................................. 49

4. My Image Function ................................................................. 50

5. Messenger Function ............................................................... 51

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Contents

6. Network Bridge Function ....................................................... 52

6.1 Connecting devices .................................................................................. 52

6.2 Communication setup ............................................................................... 53

6.3 Communication port ................................................................................. 53

6.4 Transmission method ............................................................................... 54

6.4.1 HALF-DUPLEX .............................................................................................................. 54

6.4.2 FULL-DUPLEX ............................................................................................................... 55

7. Other Functions ...................................................................... 56

7.1 E-mail Alerts ............................................................................................. 56

7.2 Projector Management using SNMP ........................................................ 58

7.3 Event Scheduling ..................................................................................... 59

7.4 Command Control via the Network .......................................................... 62

7.5 Crestron RoomView

................................................................................. 67

8. Troubleshooting ..................................................................... 68

9. Specications ......................................................................... 69

10. Warranty and after-sales service ........................................ 70

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Caution

To use the wireless network function of this projector, the designated USB wireless adapter that is sold as an option is required. For precautions according to the

standards and laws, refer to the documents that come with the adapter.

[Restriction on plugging and unplugging the USB wireless adapter]

Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet. Do not touch the USB wireless adapter that is connected to the projector while the projector is receiving AC power. Do not use any extension cable or device when connecting the adapter to the projector.

[Security precautions when using wireless LAN]

It is recommended that security settings, such as SSID and ENCRYPTION, are specied when using wireless LAN communication. If the security settings are not specied, the contents may be intercepted or it may cause unauthorized access to the system. For details on wireless LAN security settings, refer to 3.1 Projector

Web Control or

&NETWORK menu in the Operating Guide.

CAUTION

►The optional IEEE802.11b/g/n USB wireless adapter uses

the 2.4GHz radio frequency band. You do not need a radio license to use the

adapter, but you should be aware of the following:

DO NOT USE NEAR THE FOLLOWING!

•

• Microwave ovens

• Industrial, scientic or medical devices

• Designated low power radio stations

• Premises radio stations Using the USB wireless adapter near the above may cause radio interference,

which would result in a decrease in transmission speed or interruption, and even lead to malfunctioning of devices such as pacemakers.

• Depending on the location where the USB wireless adapter is used, radio wave

interference may occur, which may result in a decrease in transmission speed or interruption in communication.In particular, please be aware that using the

USB wireless adapter at locations where there is reinforced steel, other types

of metals or concrete is likely to cause radio wave interference.

• Available Channels The USB wireless adapter uses the 2.4GHz radio frequency band, but

depending on the country or region you are in, the channels that you can use

might be limited. Please consult your dealer for information on the usable

channels.

• Bringing the optional USB wireless adapter out of the country or region you reside in and using it there could lead to a violation of the radio laws of that country or region.

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.1 System requirements

1.1.1 Required equipment preparation

The following equipments are required to connect the projector to your computer

through the network.

■ Common The projector: 1 unit, Computer : minimum 1 set

■ Depending on how you want to connect

1) For the wired connection *1

LAN cable (CAT-5 or greater): 1 piece

2) For the wireless connection *2

- Projector side IEEE802.11b/g/n USB wireless adapter (option) : 1 unit

- Computer side IEEE802.11 b/g/n wireless LAN equipment: 1 unit for each *3

*1: The system for using the network function of the projector requires

communication environment conforming 100Base-TX or 10Base-T.

*2: An access point is required when the wireless LAN connection is used as

Infrastructure mode.

*3: Depending on the type of wireless network device and computer you are using,

the projector may not be able to communicate properly with your computer,

even if the computer is equipped with a built-in wireless LAN function. To eliminate communication problems, please use a Wi-Fi certied wireless

network device.

1.1.2 Hardware and software requirement for computer

To connect your computer to the projector and use the network function of the

projector, your computer needs to meet the following requirements.

ü OS: One of the following.

Windows

XP Home Edition /Professional Edition

Windows Vista® Home Basic /Home Premium /Business /Ultimate /Enterprise Windows® 7 Starter /Home Basic /Home Premium /Professional /Ultimate / Enterprise

ü CPU: Pentium 4 (2.8 GHz or higher) ü Graphic card: 16 bit, XGA or higher

* When using the “LiveViewer” it is recommended that the display resolution of

your computer is set to 1024 x 768.

ü Memory: 512 MB or higher ü Hard disk space: 100 MB or higher ü Web browser: Internet Explorer

6.0 or higher

ü CD-ROM/DVD-ROM drive

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.1 System requirements (continued)

NOTE

• The network communication control is disabled while the projector is in standby mode if the STANDBY MODE item is set to SAVING. Please connect the network communication to the projector after setting the STANDBY MODE to NORMAL. (

&SETUP menu in the Operating Guide)

• You can get the latest version of the applications for the network functions of

the projector and the latest information for this product from the website.

(http://www.christiedigital.com)

1.2 Quick connection

The “LiveViewer” supports very quick and simple connection to the network.

When making use of the network function, it is recommended that you install the

"LiveViewer" on your computer. For details, refer to the manual for "LiveViewer".

In case you don’t want to use the “LiveViewer” or you cannot use it by some reason, proceed to the manual setting, the item 1.3 for the wired LAN ( the item 1.4 for the wireless LAN. (&11)

&7) and

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.3 Manual network connection setting - Wired LAN -

This section explains how to set it up manually.

1.3.1 Equipments connection

Connect the projector and a computer with a LAN cable. * Before connecting with an existing network, contact the network administrator.

Next, check the following computer settings.

1.3.2 Network settings

This is the explanation of network connection settings for Windows Explorer.

1) Log on to Windows

7 as administrator authority. Administrator authority is the

account, which can access to all functions.

2) Open “Control Panel” from “Start” menu.

3) Open “View network status and tasks” in “Network and Internet”. With the icons in the "Control Panel" window displayed, click "Network and Sharing Center"..

7 and Internet

4) Click "Change adapter settings" in the menu on the left side of the "Network and Sharing Center" window.

(continued on next page)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.3 Manual network connection setting - Wired LAN - (continued)

5) Right-click "Local Area Connection" to open the menu, and select "Properties".

6) Select "Internet Protocol Version 4 (TCP/IPv4)" and click [Properties].

7) Select "Use the following IP address" and congure the IP address, Subnet mask and Default gateway for the computer accordingly. If a DHCP server exists in the network, you can select "Obtain an IP address automatically" and the IP

address will be assigned automatically. After setting is complete, click [OK] to close the window.

(continued on next page)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.3 Manual network connection setting - Wired LAN - (continued)

[About IP address]

■ Setting manually

The Network address portion of the IP address setting on your computer must be the same as the setting on the projector. Also, the entire IP address on the

computer must not overlap with that of the other devices on the same network, including the projector.

For example

The projector’s settings are as follows.

IP address: 192.168.1.254 Subnet mask: 255.255.255.0 (Network address: 192.168.1 in this case)

Therefore, specify the computer’s IP address as follows.

IP address: 192.168.1.xxx (xxx shows decimal number.) Subnet mask: 255.255.255.0 (Network address: 192.168.1 in this case)

Select from 1 to 254 for “xxx” not duplicating with any other equipments. In this case, since the IP address of the projector is “192.168.1.254”, specify a

setting between 1 to 253 for the computer.

NOTE

• “0.0.0.0” cannot be set to the IP address.

• The projector’s IP address can be changed by using the conguration utility

via a web browser. (

&21)

• If the projector and the computer exist in the same network (i.e., same network address), you can leave the default gateway eld blank.

• When the projector and the computer exist in different networks, the default gateway must be set. Consult to the network administrator in detail.

■ Setting automatically

When a DHCP server exists in the connected network, it is possible to assign an IP address to the projector and computer automatically.

* DHCP is abbreviation for “Dynamic Host Conguration Protocol” and has the

function to provide necessary setting for network like IP address from server to client. A server that has DHCP function is called DHCP server.

(continued on next page)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.3 Manual network connection setting - Wired LAN - (continued)

1.3.3 “Internet Option” setting

1) Click “Internet Options” in “Network and Sharing Center” window to open “Internet Properties” window.

2) Click “Connections” tab and then click [LAN settings] button to open “Local Area Network (LAN) Settings”.

3) Uncheck all boxes in “Local Area Network (LAN) Settings”

window. After setting is complete, click [OK] to close the window.

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.4

Manual network connection setting

Wireless LAN -

Using the designated USB wireless adapter (option) on the projector enables the projector and computer to communicate in both the Ad-Hoc and Infrastructure

modes.

This section is intended to explain how to set up wireless LAN connection

manually.

1.4.1 Preparation for wireless LAN connection

Fig. 1.4.1.a Without an access point communication (Ad-Hoc)

Fig. 1.4.1.b With an access point communication (Infrastructure)

* Ad-Hoc is one of the wireless LAN communication methods without having

access point to communicate.

* Infrastructure is one of the wireless LAN communication methods with having

access point to communicate. If certain quantities of equipments are used, this mode is efcient.

If communicating with existing network, consult to your network administrator.

First, insert the USB wireless adapter into one of the USB TYPE A ports. (

& Connecting with your devices in the Operating Guide)

Then, set up the computer for wireless communication.

When the computer comes with a built-in IEEE802.11b/g/n wireless LAN device, enable it and disable other network connections. If a wireless LAN device is not built into the computer, connect an IEEE802.11b/g/n wireless LAN device and

install the device driver. For details, refer to the user's guide for the computer and

wireless LAN device.

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.4 Manual network connection setting - Wireless LAN - (continued)

1.4.2 Wireless LAN connection set up

Using wireless LAN utility for Windows

7 standard.

Wireless LAN initial settings for the projector is as follows.

Connection Control : Ad-Hoc SSID : wireless Channel : 1 Encryption rating : None IP address : 192.168.10.254

* You can change these settings via a web browser on your computer or from the

menu of the projector. Refer to the item 3.1.3 Network Settings (

&20) or

NETWORK menu in the Operating Guide.

1) Select "Change adapter settings" from the menu on the left side of the "Network and Sharing Center" window.

2) Right-click "Wireless Network Connection" to open the menu, and select "Properties".

3) Select "Internet Protocol Version 4 (TCP/IPv4)" and click [Properties].

(continued on next page)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.4 Manual network connection setting - Wireless LAN - (continued)

4) Select "Use the following IP address" and congure the IP address, Subnet mask and Default gateway for the computer

accordingly. After setting is complete, click [OK] to close the window.

[About IP address]

The Network address portion of the IP address setting on your computer must be the same as the setting on the projector. Also, the entire IP address on the

computer must not overlap with that of the other devices on the same network, including the projector.

For example

The projector’s settings are as follows.

IP address: 192.168.10.254 Subnet mask: 255.255.255.0 (Network address: 192.168.10 in this case)

Therefore, specify the computer’s IP address as follows.

IP address: 192.168.10.xxx (xxx shows decimal number.) Subnet mask: 255.255.255.0 (Network address: 192.168.10 in this case)

Select from 1 to 254 for “xxx” not duplicating with any other equipments. In this case, since the IP address of the projector is “192.168.10.254”, specify

a setting between 1 to 253 for the computer.

NOTE

• “0.0.0.0” cannot be set to the IP address.

• The projector’s IP address can be changed by using the conguration utility

via a web browser. (

&20)

• If the projector and the computer exist in the same network (i.e., same network address), you can leave the default gateway eld blank.

• When the projector and the computer exist in different networks, the default

gateway must be set.

(continued on next page)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

1. Connection to the network

1.4 Manual network connection setting - Wireless LAN - (continued)

5) Right-click "Wireless Network Connection" to open the menu, and select "Connect / Disconnect".

6) From the connectable wireless networks, select the SSID of the projector (set to "wireless" by default), and click [Connect]. If

you have enabled encryption, a window asking for input of the encryption key will be displayed. Input the preset key.

7) After connection is established, "Connected" will appear to the

right of SSID.

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

2. Network Presentation

The projector can display or play back the computer screen images and audio

data that are transmitted through the network. This Network Presentation feature

helps you to smoothly make your presentations and conduct conferences.

Wireless LAN

Wired LAN

To use Network Presentation, an exclusive application, "LiveViewer" is required. It can be installed from the bundled application CD. You can also download the latest version and relevant information from the website (http://www.christiedigital. com). For details of Network Presentation and instructions to install the "LiveViewer", refer to the manual for "LiveViewer".

To start the Network Presentation, select the LAN port as the input source on the projector and click the Starting Capture button on the “LiveViewer”. "LiveViewer" function use depends on the model you are using. If you want to use the latest downloaded "LiveViewer", please refer for the appropriate group item in the "LiveViewer" User's Manual. This model will be in the Group of B.

NOTE

• When the screen resolution of your computer is over specied, the

computer image is shrunk in specied size as below before transferring to the

projector.

LX501, LX601i: 1024 x 768 (XGA) The other models: 1280 x 800

The transferred image is displayed as shrunk on the projected screen even if the panel resolution of the projector is larger than above.the panel resolution of the projector is larger than above.

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

3. Web Control

You can adjust or control the projector via a network from a web browser on a

computer that is connected to the same network.

NOTE

• Internet Explorer® 6.0 or later is required.

• If JavaScript® is disabled in your web browser conguration, you must enable JavaScript® in order to use the projector web pages properly. See the Help les for your web browser for details on how to enable JavaScript®.

• It is recommended that all web browser updates are installed.

• If data is transferred via wireless and wired LAN at the same time, the

projector may not be able to process the data correctly.

Refer to the following for conguring or controlling the projector via a web browser. Make sure that your computer and the projector is connected via network, and

then start Web browser.

Enter the projector's IP address into URL input box of the Web browser as the

example below, and then press the Enter key or button. Example: If the IP address of the projector is set to 192.168.1.10:

Enter “http://192.168.1.10/” into the address bar of the web browser and press the Enter key or click

button.

If a correct URL is input, and the

projector and your computer are connected to the same network correctly, the selection window as shown on the right will be displayed.

You can choose to use Projector Web Control or Crestron e-Control® as a tool for controlling the projector. Click one of

them. For more details, refer to 3.1 Projector Web Control (

&17) or 3.2 Crestron

e-Control® (&42).

NOTE

• Do not attempt to control the projector with the projector's menu or

remote control, and via Web Control at the same time. It may cause some

operational errors in the projector.

• If Crestron e-Control in the Network Settings (

&21) is set to Disable, the selection window above does not appear, but the Logon window of the Projector Web Control is displayed.

• Crestron e-Control

is created using Flash®. You need to install Adobe® Flash®

Player on your computer to use Crestron e-Control®.

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

3.1 Projector Web Control

3.1.1 Logon

To use the Projector Web Control function, you need

to logon with your user name and password.

Below are the factory default settings for user

name and password.

3. Web Control

User name Password

Logon window

Administrator <blank>

Enter your user name and password, and then click the [OK]. If you logon successfully, the screen below will be displayed.

Main menu

Click the desired operation or conguration item on the main menu.

NOTE

• The language used on the Projector Web Control screen is the same as that of the OSD on the projector. If you want to change it, you need to change the OSD language on the projector. (

&SCREEN menu in the

Operating Guide)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

3. Web Control

3.1 Projector Web Control (continued)

3.1.2 Network Information

Displays the projector’s current network conguration settings.

Item Description

Common Information

Projector Name Displays the projector name settings.

Wireless Information Displays the current settings of wireless LAN.

Mode Displays the mode of wireless LAN communication.

DHCP Displays the DHCP setting.

IP Address Displays the IP address. Subnet Mask Displays the subnet mask.

Default Gateway Displays the default gateway. DNS Server Address Displays the DNS server address.

MAC Address Displays the MAC address. Ch Displays the channel used for wireless LAN. Encryption Displays the data encryption setting.

SSID Displays the SSID used by the projector.

Speed Displays the current wireless LAN transmission speed.

Wired Information Displays the current wired LAN settings.

DHCP Displays the DHCP setting.

IP Address Displays the IP address. Subnet Mask Displays the subnet mask.

Default Gateway Displays the default gateway. DNS Server Address Displays the DNS server address.

MAC Address Displays the MAC address.

Displays information common to both wireless and wired LAN.

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

3.1 Projector Web Control (continued)

3.1.3 Network Settings

Displays and congures network settings.

Item Description

Common Setup

Projector Name

sysLocation (SNMP)

sysContact (SNMP)

AMX D.D. (AMX Device Discovery)

Congures the settings common to wireless and wired LAN. Congures the name of the projector.

The length of the Projector Name can be up to 64

alphanumeric characters. Only alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space. Particular projector name is pre-assigned by default.

Congures the location to be referred to when using SNMP. The length of the sysLocation can be up to 255 alphanumeric characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can

be used.

Congures the contact information to be referred to when using SNMP. The length of the sysContact can be up to 255 alphanumeric characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can

be used.

Congures the AMX Device Discovery setting to detect the projector from the controllers of AMX connected to the same network. For the details of AMX Device Discovery, visit the AMX web site.

URL: http://www.amx.com (as of Jun. 2012)

3. Web Control

(continued on next page)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

3. Web Control

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wireless Setup Congures the wireless LAN settings.

Mode Select "Ad-Hoc" or "Infrastructure".

IP Conguration Congures network settings.

DHCP ON Enables DHCP. DHCP OFF Disables DHCP.

IP Address Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled.

Default

Gateway

DNS Server Address Congures the DNS server address.

Congures the default gateway when DHCP is disabled.

Select from “1” to “11” a channel to use in the Ad-Hoc mode.

• Depending on the country where you are

NOTE

the channels may vary. In addition, depending on the

country or region where you are may be required to use a wireless network card that conrm to the standards in the

respective country or region.

Encryption Select data encryption method.

Input the WEP key. Either ASCII characters or hexadecimal numbers can be used during WEP key input. However, you cannot use a combination of both.The length of the key is dened as

WEP Key

follows according to the WEP and character formats.

Encryption ASCII characters HEX numbers WEP 64bit 5 characters 10 characters

WEP 128bit 13 characters 26 characters

Input WPA Passphrase.

WPA Passphrase

Available number of input characters is 8 to 63. Only alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@ [\]^_`{|}~ and space Select an SSID from the list.

If you require to set your unique SSID, select [Custom], then

SSID

set your own SSID following the rules below. Maximum number of input characters is 32.

Only alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.

(continued on next page)

Network Guide 020-000475-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wired Setup Congures the wired LAN settings.

IP Conguration Congures network settings.

DHCP ON Enables DHCP. DHCP OFF Disables DHCP.

IP Address Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled.

Default

Gateway

DNS Server Address Congures the DNS server address.

Other Setup Congures other network settings.

Crestron e-Control

Congures the default gateway when DHCP is disabled.

Set whether to or not to use Crestron e-Control If you choose Disable, the Logon window of Projector Web Control and not the selection window will be displayed at rst of the Web Control.

Click the [Apply] button to save the settings.

3. Web Control

NOTE

• The new conguration settings are activated after restarting the network connection. When the conguration settings are changed, you must restart the network connection. You can restart the network connection from

Network Restart on the main menu (

&41).

• If you connect the projector to an existing network, consult a network

administrator before setting server addresses.

• The WEP Key, WPA passphrase and SSID settings will not be set if the invalid

characters are used.

• The projector does not allow both wireless and wired LAN to be connected to the same network. Do not set the same network address for both wireless and wired LAN.

+ 51 hidden pages