User Manual
Table of Contents
TABLE OF CONTENTS
1. Before You Begin ............................................................................... 1
What Is Included ........................................................................................... 1
Unpacking Instructions.................................................................................. 1
Claims ................................................................................................................ 1
Text Conventions .......................................................................................... 1
Symbols ........................................................................................................ 1
Disclaimer ..................................................................................................... 1
Intellectual Property ...................................................................................... 1
Safety Notes.................................................................................................. 2
2. Introduction......................................................................................... 3
Product Overview.......................................................................................... 3
Product Dimensions ...................................................................................... 3
3. Setup.................................................................................................... 4
AC Power...................................................................................................... 4
Fuse Replacement ............................................................................................. 4
Power Linking..................................................................................................... 4
Mounting ....................................................................................................... 5
Orientation.......................................................................................................... 5
Rigging ............................................................................................................... 5
4. Operation............................................................................................. 6
Control Panel Operation................................................................................ 6
Menu Map ..................................................................................................... 6
Configuration (DMX) ..................................................................................... 6
Personality and Starting Address....................................................................... 6
D-Fi USB Connectivity .................................................................................. 7
D-Fi USB Compatibility ...................................................................................... 7
Configuration (D-Fi USB) ................................................................................... 7
D-Fi USB DIP Switch Channels............................................................................... 7
DMX Channel Assignments and Values ....................................................... 8
4Ch .......................................................................................................................... 8
Configuration (Standalone) ........................................................................... 9
Static Color......................................................................................................... 9
Automatic Programs........................................................................................... 9
Program Speed ....................................................................................................... 9
Sound-Active Mode............................................................................................ 9
Sound Sensitivity................................................................................................ 9
Manual Mode ..................................................................................................... 9
Configuration (Settings) ................................................................................ 10
Dimmer Speed ................................................................................................... 10
Factory Reset..................................................................................................... 10
IRC-6 Infrared Remote Control ..................................................................... 10
IRC-6 Operation ................................................................................................. 10
Master/Slave Mode (Wired) .......................................................................... 11
Master/Slave Mode (D-Fi USB)..................................................................... 11
ILS Mode....................................................................................................... 11
5. Maintenance........................................................................................ 12
Product Maintenance .................................................................................... 12
6. Technical Specifications.................................................................... 13
Warranty & Returns................................................................................ 14
Limited Warranty........................................................................................... 14
Returns.......................................................................................................... 14
Contact Us............................................................................................... 15
LED Shadow 2 ILS User Manual Rev. 1
Before You Begin
1. Before You Begin
What Is Included
• LED Shadow 2 ILS
• Power cord
• Quick Reference Guide
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
Symbols
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetdj.com
.
Intellectual Property
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2023 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, and LED Shadow 2 ILS are registered trademarks or trademarks of Chauvet
& Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other
company and product names and logos referred to herein may be trademarks of their respective
companies.
LED Shadow 2 ILS User Manual Rev. 1
Page 1 of 15
Safety Notes
• This product is not intended for permanent installation.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a safety cable.
• Make sure there are no flammable materials close to the product when operating.
• Do not touch the product’s housing when operating because it may be very hot.
• The voltage of the outlet to which you are connecting this product must be within the range
stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the
product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer or rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the handles.
• The maximum ambient temperature is 104 °F (40 °C). Do not operate this product at higher
temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Do not open this product. It contains no user-serviceable parts.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Before You Begin
Keep this User Manual for future use. If the product is sold to someone else, be sure that they
also receive this document.
Page 2 of 15
LED Shadow 2 ILS User Manual Rev. 1
Introduction
DMX
in/out
Fuse
holder
Power
in
Menu
buttons
LED display
IR sensor
Safety cable
pass-through
Microphone
D-Fi USB
port
Power
out
8.2 in
208 mm
14 in
355 mm
2.2 in
55 mm
2. Introduction
Product Overview
WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may
cause damage to the product.
Product Dimensions
LED Shadow 2 ILS User Manual Rev. 1
Page 3 of 15
Setup
1st product 2nd product 3rd product
Additional
products
Power
source
3. Setup
AC Power
The LED Shadow 2 ILS has an auto-ranging power supply and it can work with an input voltage range of
100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current
value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The listed current rating indicates the product’s average current draw under normal conditions.
• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or
fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse Replacement
1. Disconnect the product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power-Linking
The product provides power linking via the outlet located in the back of the product. See the diagram below
for further explanation.
Power-Linking Diagram
It is possible to power link up to 11 LED Shadow 2 ILS products on 120 VAC or up to 20 LED
Shadow 2 ILS
The power-linking diagram corresponds to the North American version of the product ONLY!
If using the product in other markets, consult with the local Chauvet distributor as powerlinking connectors and requirements may differ by country or region.
products on 230 VAC.
Page 4 of 15
LED Shadow 2 ILS User Manual Rev. 1
Setup
Safety cable
(such as CH-05
from Chauvet)
Mounting clamp
(such as CLP-15 from Chauvet)
Mounting bracket
Bracket adjustment knob
(x2)
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
Orientation
The LED Shadow 2 ILS may be mounted in any position; however, make sure adequate ventilation is
provided around the product.
Rigging
• Before deciding on a location, always make sure there is easy access to the product for
maintenance and programming.
• Make sure adequate ventilation is provided around the product.
• Make sure that the structure or surface onto which the product is being mounted can support the
product’s weight. (see the Technical Specifications
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to
reach.
• When mounting the product on the floor, make sure that the product and cables are away from
people and vehicles.
Mounting Diagram
)
LED Shadow 2 ILS User Manual Rev. 1
Page 5 of 15
Operation
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located underneath the display. Please refer to
the Product Overview
Button Function
<MENU> Press to find an operation mode or to back out of the current menu option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Refer to the LED Shadow 2 ILS product page on
Mode Programming Levels Description
DMX 4Ch d 1–509 4-channel DMX mode
Automatic
Program
Speed S-- S. 1–100 Automatic program speed
Sound-Active
Sensitivity SEnS u 0–100 Sound sensitivity
Manual Mode u--
Reset
Infrared ir
ILS iLS iLS1–4 Sets ILS mode
to see the button locations on the control panel.
www.chauvetdj.com
P 1 3-zone chase 1
P 2 3-zone chase 2
P--
Snd
SEt
S.
_ _ _
P 3 3-zone fade
P 4 Pulse effect 0-100%
P 5 Pulse effect 0-100-0%
P 6 Strobe
Snd1 Sound-active 3-zone chase 1
Snd2 Sound-active 3-zone chase 2
Snd3 Sound-active 3-zone fade
Snd4 Sound-active pulse effect 0-100%
Snd5 Sound-active pulse effect 0-100-0%
Snd6 Sound-active strobe
u. 0–255 Manual dimmer
S. 0 Manual strobe: off
S. 1–99 Manual strobe: slow to fast
S.100 Manual strobe: sound-active
rESt Reset to factory default settings
oFF
on
Enables/disables infrared control
for the latest menu map.
Page 6 of 15
LED Shadow 2 ILS User Manual Rev. 1
Operation
Receiving
Receiving
Transmitting
Transmitting
Configuration (DMX)
The LED Shadow 2 ILS works with a DMX controller. Information about DMX is in the CHAUVET DMX
Primer, which is available from the Chauvet website
chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf
Personality and Starting Address
The LED Shadow 2 ILS uses up to 4 DMX channels in the 4Ch mode, which defines the highest
configurable address to 509.
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX
mode uses. If the starting address is set too high, access to some channels could be restricted.
For information about the DMX protocol, download the DMX Primer from www.chauvetdj.com
To select the personality and starting address, do the following:
1. Press <MENU> repeatedly until 4Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address, from d 1–509.
4. Press <ENTER>.
.
D-Fi USB Connectivity
The LED Shadow 2 ILS is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB
from Chauvet DJ. Simply set the product's DMX Personality and DMX Address, set the DIP switch
D-Fi receiving/transmitting channel, then plug it into the D-Fi USB port.
WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may
cause damage to the product.
Once plugged in, the D-Fi USB will take over the product. Wired DMX and manual display
control / menu buttons will be unavailable until the D-Fi USB is unplugged. The priority
levels are:
1. D-Fi USB
2. Wired DMX
3. Manual Digital Display/Menu Buttons
D-Fi USB Compatibility
The D-Fi USB can receive a DMX signal from the D-Fi Hub, the FlareCON Air 2, and other D-Fi USB
products.
Configuration (D-Fi USB)
1. Set the DMX Personality and DMX address on the LED Shadow 2 ILS.
2. Use the Chart provided to set BOTH:
• the Channel, and then
• The Receiving or Transmitting option
NOTE: DIP Switch 5
D-Fi USB DIP Switch Channels
is for Transmitting OR Receiving, please choose carefully.
.
Ch. 1 2 3 4 T/R Ch. 1 2 3 4 T/R Ch. 1 2 3 4 T/R Ch. 1 2 3 4 T/R
1 9 1 9
2 10 2 10
3 11 3 11
4 12 4 12
5 13 5 13
6 14 6 14
7 15 7 15
8 16 8 16
LED Shadow 2 ILS User Manual Rev. 1
Page 7 of 15
DMX Channel Assignments and Values
4Ch
Channel Function Value Percent/Setting
000 004 No function
005 039 P1: 3-zone chase 1
040 079 P2: 3-zone chase 2
1Program
2 Program speed 000 255 Program speed, slow to fast
Strobe
(when Ch. 1 is 005 199)
3
Lightning effect
(when Ch. 1 is 200 239)
4 Dimmer 000 255 0–100%
080 119 P3: 3-zone fade
120 159 P4: Pulse effect 0-100%
160 199 P5: Pulse effect 0-100-0%
200 239 P6: Strobe
240 255 Sound-active (cycles P1-P5)
000 No function
001 250 Strobe, slow to fast
251 255 Sound-active strobe
000 No function
001 250 Lightning effect, slow to fast
251 255 Sound-active lightning effect
Operation
Page 8 of 15
LED Shadow 2 ILS User Manual Rev. 1
Operation
Configuration (Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX signals
that could interfere with the DMX signals from the controller.
Automatic Programs
To run the LED Shadow 2 ILS with an automatic program, do the following:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select a program, from P 1–6.
4. Press <ENTER>.
Program Speed
To set the program speed of the LED Shadow 2 ILS, do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to increase or decrease the speed, from S. 1–100.
4. Press <ENTER>. The display will return to the selected program.
Sound-Active Mode
To run the LED Shadow 2 ILS in sound-active mode, do the following:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Sound Sensitivity
To set the sound sensitivity on the LED Shadow 2 ILS, do the following:
1. Press <MENU> repeatedly until SenS shows on the display.
2. Use <UP> or <DOWN> to increase or decrease the program speed, from u 0–100.
3. Press <ENTER>. The product will return to sound-active mode.
Manual Mode
To run the LED Shadow 2 ILS with a custom color and strobe speed, do the following:
1. Press <MENU> repeatedly until u-- shows on the display.
2. Press <ENTER> and one of the following will show on the display:
• s. _ _ _ (strobe)
3. Use <UP> or <DOWN> to increase or decrease the value, from 0–255 (for dimmer) or from 0–100
(for the strobe speed: 0 is off, 1–99 is slow to fast, 100 is sound-active).
4. Press <ENTER>. to cycle through the options.
5. Repeat steps 3-4 until the product is set as desired.
LED Shadow 2 ILS User Manual Rev. 1
Page 9 of 15
BLACK
OUT
AUTO
SOUND
SENSITIVITY
SPEEDSTROBE
%
MANUAL
FADE
RGB
WUVA
+
0
-
123
654
789
Operation
Configuration (Settings)
Factory Reset
To reset the LED Shadow 2 ILS to factory default settings, do the following:
1. Press <MENU> repeatedly until SEt shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select rESt.
4. Press <ENTER>.
IRC-6 Infrared Remote Control
The LED Shadow 2 ILS is compatible with the IRC-6 infrared remote control from Chauvet. To run the LED
Shadow 2 ILS in IR mode, follow the instructions below.
1. Press <MENU> repeatedly until SEt shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select ir.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select from oFF or on.
6. Press <ENTER>.
IRC-6 Operation
Automatic Programs
To run an automatic program with the IRC-6, press <AUTO>
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to select the program.
FAD E
To run the FADE program with the IRC-6, press <FADE>.
1. Press <FADE> on the IRC-6.
2. Press <+> or <–> to select the program.
To set the program speed with the IRC-6:
1. Press <SPEED> on the IRC-6.
2. Press <+> or <–> to increase or decrease the speed.
Sound-Active Mode
To run the sound-active mode with the IRC-6, press <SOUND>.
To set the sound sensitivity with the IRC-6:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <+> or <–> to increase or decrease the sensitivity.
Manual Mode
To mix a custom color with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Press <R> (red), <G> (green), <B> (blue), or <A> (amber) to select which
color to edit.
3. Press <+> or <–> to increase or decrease the value of the selected color.
To select a preset color with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Press <P/UV>, <W>, or <0>–<9> to select the color.
Strobe
To adjust the strobe rate with the IRC-6:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe, or set the strobe to 0.
Black Out
To black out the lights with the IRC-6, press <BLACK OUT>.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC-6 will not respond to any inputs when Black Out is activated. If
the product does not respond when a button is pressed, try pressing <BLACK
OUT>. Black Out may have been activated.
Page 10 of 15
LED Shadow 2 ILS User Manual Rev. 1
Operation
Master/Slave Mode (Wired)
The Master/Slave mode allows a single LED Shadow 2 ILS product (the “master”) to control the actions of
one or
more LED Shadow 2 ILS products (the “slaves”) without the need of a DMX controller. The master
product will be
set to operate in slave mode. Once set and connected, the slave products will operate in unison with the
master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 4Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select d 1.
4. Press <ENTER>.
5. Connect the DMX input of the first slave product to the DMX output of the master product.
6. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave
7. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in standalone mode or with the IRC-6.
2. Make the master product the first product in the DMX daisy chain.
set to operate in either standalone mode or with the IRC-6, while the slave products will be
product.
• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave operation
because the controller may interfere with the signals from the master.
• Do not connect more than 31 slaves to the master.
Master/Slave Mode (D-Fi USB)
The D-Fi USB allows a single LED Shadow 2 ILS product (the “master”) to control the actions of one or
more LED Shadow 2 ILS products (the “slaves”) without the need of a DMX controller or DMX cables. The
master (transmitter) product will be set to operate in standalone mode or with the IRC-6, while the slave
(receiver) products will be set to operate in DMX mode. Once set and connected, the slave products will
operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 4Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to set the starting address to d 1.
4. Press <ENTER>.
5. Set the D-Fi USB to receive on a specific channel, 1–16.
6. Plug in the D-Fi USB.
7. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in standalone mode.
2. Set the D-Fi USB to transmit on the D-Fi channel the slaves are receiving on.
3. Plug in the D-Fi USB.
• All products must be set to the same DMX personality, DMX address, and D-Fi channel.
• Configure all the slave products before configuring the master to transmit.
• Never connect a DMX controller to a D-Fi channel configured for Master/Slave operation
because the controller may interfere with the signals from the master.
ILS Mode
ILS (Integrated Lighting System) provides 4 modes that synchronize with the GigBAR MOVE+ILS: Modes
1 and 3 synchronize with side 1 of the GigBAR MOVE+ILS, whereas modes 2 and 4 synchronize with side
2 of the GigBAR MOVE+ILS. When linked, effects will sync with the most similar effect on the selected side
of the GigBAR MOVE+ILS: Kinta effects will sync with one of the kintas, wash effects will sync with one of
the pars, etc. This product will synchronize with the par on the selected side of the GigBAR MOVE+ILS.
To set the LED Shadow 2 ILS to respond to an ILS signal:
1. Press <MENU> repeatedly until iLS shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select from iLS1 (side 1), iLS2 (side 2), iLS3 (side 1), or iLS4 (side 2).
4. Press <ENTER>.
LED Shadow 2 ILS User Manual Rev. 1
Page 11 of 15
Maintenance
5. Maintenance
Product Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean
your lighting products at least twice a month. However, be aware that usage and environmental conditions
could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
Page 12 of 15
LED Shadow 2 ILS User Manual Rev. 1
Technical Specifications
6. Technical Specifications
Dimensions and Weight
Length Width Height Weight
8.2 in (208 mm) 14 in (355 mm) 2.2 in (55 mm) 6 lb (2.8 kg)
Note: Dimensions in inches are rounded.
Power
Power Supply Type Range Voltage Selection
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 Hz 230 V, 50 Hz
Consumption 49 W 49 W
Operating Current 0.7A 0.4 A
Power linking current (products) 8 A (11 products) 8 A (20 products)
Fuse T1 A, 250 V T1 A, 250 V
Power I/O U.S./Worldwide UK/Europe
Power input connector IEC IEC
Power output connector Edison IEC
Power Cord plug Edison (U.S.) Local Plug
Light Source
Type Color Quantity Power Current Lifespan
LED
UV
18 3 W 0.6 A 50,000 hours
Photometrics
Strobe Rate Coverage Angle
0 to 20 Hz 32°
Thermal
Maximum External Temperature Cooling System
104 °F (40 °C) Convection
DMX
I/O Connector Channel Range
3-pin XLR 4
Ordering
Product Name Item Code UPC Number
LED Shadow 2 ILS 10121916 781462222642
LED Shadow 2 ILS User Manual Rev. 1
Page 13 of 15
Warranty & Returns
Warranty & Returns
Limited Warranty
FOR WARRANTY REGISTRATION AND COMPLETE TERMS AND CONDITIONS PLEASE VISIT OUR
WEBSITE.
For Customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration
For Customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg,
France, and Germany: www.chauvetlighting.eu/warranty-registration
Chauvet warrants that this product shall be free from defects in material and workmanship under normal
use, for the period specified in, and subject to the exclusions and limitations set forth in the full limited
warranty on our website. This warranty extends only to the original purchaser of the product and is not
transferable. To exercise rights under this warranty, you must provide proof of purchase in the form of an
original sales receipt from an authorized dealer that shows the product name and date of purchase.
THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. This warranty gives you specific legal
rights. You may also have other rights that vary from state to state and country to country. This warranty is
valid only in the United States, United Kingdom, Republic of Ireland, Belgium, the Netherlands,
Luxembourg, France, Germany and Mexico. For warranty terms in other countries, please consult your
local distributor.
.
Returns
In case support or return of product is needed:
• If located in the U.S., contact Chauvet World Headquarters.
• If located in the U.K. or Ireland, contact Chauvet U.K.
• If located in Benelux, contact Chauvet Benelux.
• If located in France, contact Chauvet France.
• If located in Germany, contact Chauvet Germany.
• If located in Mexico, contact Chauvet Mexico.
• If located in any other country, DO NOT contact Chauvet. Instead, contact your local distributor. See
www.chauvetdj.com
Mexico.
If located outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact the
distributor of record and follow their instructions on how to return Chauvet products to
them. Visit our website www.chauvetdj.com
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization
(RMA) number before shipping the product. Be prepared to provide the model number, serial number, and
a brief description of the cause for the return.
To submit a service request online, go to www.chauvetdj.com/service-request
Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet
will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product returned without an RMA
number.
for distributors outside the U.S., U.K., Ireland, Benelux, France, Germany, or
for contact details.
.
.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly
on the box.
Before sending the product, clearly write the following information on a piece of paper and place it inside
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).
Page 14 of 15
LED Shadow 2 ILS User Manual Rev. 1
Contact Us
Contact Us
General Information Technical Support
Chauvet World Headquarters
Address: 3360 Davie Rd. Voice: (844) 393-7575
Davie, FL 33314 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetdj.com
Chauvet U.K.
Address: Unit 1C Email: UKtech@chauvetlighting.eu
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website: www.chauvetdj.eu
NG16 6NT
Voice: + 44 (0) 17 7 3 511115
Fax : + 44 (0) 1 7 7 3 511110
Chauvet Benelux
Address: Stokstraat 18 Email: BNLtech@chauvetlighting.eu
9770 Kruishoutem
Belgium Website: www.chauvetdj.eu
Voice: +32 9 388 93 97
Chauvet France
Address: 3, Rue Ampère
91380 Chilly-Mazarin
France Website: www.chauvetdj.eu
Voice: +33 1 78 85 33 59
Chauvet Germany
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Germany Website: www.chauvetdj.eu
Voice: +49 421 62 60 20
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B
(Entrance by Calle 2)
Zona Industrial Lerma Website: www.chauvetdj.mx
Lerma, Edo. de México, CP 52000
Voice: +52 (728) 690-2010
Visit the applicable website above to verify our contact information and instructions to request support.
Outside the U.S., U.K., Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record.
Email: FRtech@chauvetlighting.fr
Email: DEtech@chauvetlighting.de
Email: servicio@chauvet.com.mx
LED Shadow 2 ILS User Manual Rev. 1
Page 15 of 15
Loading...