User Manual
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 3
What Is Included ............................................................................................................................. 3
Unpacking Instructions .................................................................................................................... 3
Claims ..................................................................................................................................................... 3
Text Conventions ............................................................................................................................ 3
Symbols .......................................................................................................................................... 3
Disclaimer ....................................................................................................................................... 3
Product at a Glance ........................................................................................................................ 4
Safety Notes .................................................................................................................................... 4
2. Introduction ................................................................................................................... 5
Product Overview ............................................................................................................................ 5
Product Dimensions ........................................................................................................................ 6
3. Setup .............................................................................................................................. 7
AC Power ........................................................................................................................................ 7
Fuse Replacement .......................................................................................................................... 7
Power Linking ......................................................................................................................................... 7
Mounting ......................................................................................................................................... 8
Orientation .............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation ....................................................................................................................... 9
Control Panel Operation.................................................................................................................. 9
Menu Map ....................................................................................................................................... 9
DMX Linking .................................................................................................................................. 10
Configuration (DMX) ............................................................................................................................. 10
DMX Starting Address .......................................................................................................................... 10
DMX Channel Assignments and Values ....................................................................................... 10
3-CH ..................................................................................................................................................... 10
Configuration (Standalone) ........................................................................................................... 11
Auto Programs ...................................................................................................................................... 11
Sound-Active ........................................................................................................................................ 11
Manual Mode ........................................................................................................................................ 11
Display Timeout .................................................................................................................................... 11
Test Mode ............................................................................................................................................. 11
Reset .................................................................................................................................................... 11
IRC-6 Infrared Remote Control ..................................................................................................... 12
IRC-6 Operation.................................................................................................................................... 12
Master/Slave Mode ....................................................................................................................... 12
5. Maintenance .................................................................................................................13
Product Maintenance .................................................................................................................... 13
6. Technical Specifications ..............................................................................................14
Returns .............................................................................................................................15
Contact Us ........................................................................................................................16
Page 2 of 16 LED Shadow™ User Manual Rev. 6
What Is
Included
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
If the box or the contents (the product and included accessories) appear damaged from
Text
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Critical installation, configuration, or operation information. Not
damage to the product, or cause harm to the operator.
Disclaimer
The information and specifications contained in this document are subject to change
assumes no responsibility or liability for any errors or omissions
reserves the right to update the existing
1. BEFORE YOU BEGIN
Claims
Conventions
• LED Shadow™
• Power Cord
parts are in the package and are in good condition.
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure
to report damage to the carrier immediately may inv alidate y our claim. In addition, keep the
box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Convention Meaning
Symbol Meaning
Electrical warning. Not following these instructions may cause
electrical damage to the product, accessories, or the user.
• Warranty Card
• Quick Reference Guide
following these instructions may make the product not work, cause
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
without notice. Chauvet
that may appear in this manual. Chauvet
document or to create a new document to correct any er rors o r omissions .
You can download the latest version of this docume nt f rom www.chauvetlighting.com.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
R. Isenstadt 07/14/2015 M. Trouard 07/14/2015
Author Date Editor Updated
LED Shadow™ User Manual Rev. 6 Page 3 of 16
Product at a
x
P
x
P
P
P
P
x
P
Safety Notes
Do not touch the product’s housing when operating because it may be very hot.
completely disconnect the product from power via breaker or by unplugging it.
Glance
Use on Dimmer
Outdoor Use
Sound-Active
DMX
Master/Slave
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about instal lation, usage, and maintenance.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing
the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a
safety cable.
• Make sure there are no flammable materials close to the product when operating.
•
• The product is not intended for permanent installation.
• Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
Auto Programs
Auto-ranging Power Supply
Replaceable Fuse
User-Serviceable
Keep this User Manual for future use. If you sell the product to someone else, b e
sure that they also receive this document.
Page 4 of 16 LED Shadow™ User Manual Rev. 6
2. INTRODUCTION
Product Overview
Safety Loop
Display
Menu Buttons
Microphone
Sensitivity Knob
Fuse Holder
Power In
Power Out
DMX In/Out
LED Shadow™ User Manual Rev. 6 Page 5 of 16
Product Dimensions
6.5 in
165 mm
14 in
356 mm
9.8 in
248 mm
Page 6 of 16 LED Shadow™ User Manual Rev. 6
AC Power
The LED Shadow™ has an auto-ranging power supply and it can work with an input
circuit breaker, power outlet, and wiring), use the current value listed on the
’s specifications chart. The
listed current rating indicates the product’s aver age c urrent dra w under normal conditions.
• Always connect the product to a protected circuit (circuit breaker or fuse).
has an appropriate electrical ground to avoid the risk
To eliminate unnecessary wear and improve its lifespan, during periods of
use completely disconnect the product from power via breaker or by
unplugging it.
to a rheostat (variable resistor) or dimmer circuit, even if
Fuse
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
4. Insert the fuse holder back in place and reconnect power.
Power Linking
s on 120 VAC or
in other markets, you must consult with the
1st Product
2nd Product
3rd Product
Additional
Products
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap
3. SETUP
Replacement
voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power
requirements (
label affixed to the product’s back panel, or refer to the product
Make sure the product
of electrocution or fire.
•
non-
Never connect the product
the rheostat or dimmer channel serves o nly as a 0 t o 100% switch.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking
The product provides power linking via the Edison outlet located in the back of the product.
Please see the diagram below for further explanation.
Diagram
You can power link up to 43 LED Shadow™ product
up to 74 LED Shadow™ products on 230 VA C .
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product
local Chauvet distributor as powe r linking connectors and requirements may differ
in your country or region.
LED Shadow™ User Manual Rev. 6 Page 7 of 16
Mounting
, read and follow the safety recommendations indicated in the
may be mounted in any position; however, make sure adequate
of appropriate weight
knobs allow for directional adjustment when aiming the
Mounting Clamp
15N
from Chauvet)
Mounting Bracket
Safety Cable
from Chauvet)
Bracket Adjustment
Knob x 2
Flush Mounting
Bracket
Before mounting the product
Safety Notes.
Orientation
The LED Shadow™
ventilation is provided around the product.
Rigging
• Before deciding on a location for the product, always make sure there is easy access
to the product for maintenance and progr amming pur pose s.
• Make sure that the structure onto which you are mounting the product can support the
product’s weight. See the T echnical Specif ications for weight information.
• When mounting the product overhead, always use a safety cable. Mount the product
securely to a rigging point, whether an elev at ed platform or a t r uss .
• When rigging the product onto a truss, use a mounting clamp
capacity.
• When power linking multiple products, mount the products close enough for power
linking cables to reach.
• The bracket adjustment
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
(such as the CLP-
Mounting Diagram
(such as CH-05
Flush Mounting
to Wall (Drywall
Screws x 4)
Page 8 of 16 LED Shadow™ User Manual Rev. 6
Control Panel
Operation
Press to find an operation mode or to back out of the current menu
option
Navigates upwards through the menu list and increases the numeric
value when in a function
Navigates downwards through the menu list and decreases the
numeric value when in a function
Enables the currently displayed menu or sets the currently selected
value into the selected function
Menu Map
Main Level
Programming Steps
Description
Aut0
Aut1
Aut2
Aut3
Aut4
Aut5
Sou
(sound-active)
L.000–255 (UV)
Dimmer
S. 0–8
Strobe rate
Addr
d001–510
SLA
SLAV
Slave mode
On
Display timeout on
oFF
Display timeout off
tESt
Performs a test of all LEDs
rEST
Resets the software
4. OPERATION
To access the control panel functions, use the four buttons located underneath the display.
Please refer to the Product Overview to see the button locations on the control panel.
Button Function
<MENU>
<ENTER>
<UP>
<DOWN>
Aut
(automatic)
CoL CoLo
SYS
LEdS
Soud
S. 01–99
Automated programs and
speed
Sound-Active mode
3-channel DMX mode
LED Shadow™ User Manual Rev. 6 Page 9 of 16
DMX Linking
The LED Shadow™ works with a DMX controller. Information about DMX is in the
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Configuration
Set the product in DMX mode to control with a DMX controller.
socket on the product.
Starting
When selecting a starting DMX address, always consider the number of DMX channels the
uses. If you choose a starting address that is too high, you could restrict the
DMX channels, which defines the highest configurable
ocol, download the DMX Primer
4. Press <ENTER>.
DMX Channel Assignments and V alues
Channel
Function
Value
Percent/Setting
000
No function
040 ó 079
Automatic m ode 1
080 ó 119
Automatic mode 2
120 ó 159
Automatic mode 3
160 ó 199
Automatic mode 4
200 ó 239
Automatic mode 5
240 ó 255
Sound-active
000 ó 009
No strobe
010 ó 255
Strobe speed (0–100%)
Auto Mode Speed
(When Ch. 1 is 040 ó 239)
No Function
(When Ch. 1 is 240 ó 255)
3
Intensity
CHAUVET® DMX Primer, which is available from the Chauvet website
DMX
(DMX)
Address
3-CH
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
product
access to some of the product’s channels.
The LED Shadow™ uses 3
address to 510. If you are not familiar with the DMX prot
from www.chauvetlighting.com.
To select the starting address, do the follow ing:
1. Press <MENU> repeatedly until Addr shows on the display.
2. Press <ENTER> and d001–510 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.
001 ó 039
1
Mode
Dimmer mode
Strobe Mode Speed
(When Ch. 1 is 001 ó 039)
2
000 ó 255
000 ó 255
000 ó 255
Automatic mode speed (slow to fast)
No function
100–0%
Page 10 of 16 LED Shadow™ User Manual Rev. 6
Configuration
(Standalone)
to a DMX string
transmit DMX
To run an auto program, do the following:
6. Press <ENTER>.
To run the LED Shadow™ in sound-active mode, follow the instructions below:
3. Turn the sensitivity knob until the product responds to the beat of the music.
Manual Mode
To run the LED Shadow™ in manual mode, follow the instructi ons below:
7. Press <ENTER>.
To turn the display timeout on or off, do the following:
6. Press <ENTER>.
To run a test of the LEDs, follow t he instructions below:
<ENTER>
4. Press <ENTER>.
Set the product in one of the standalone mo des to c ont rol without a DMX controller.
Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode
connected to a DMX controller. Products in standalone mode may
signals that could interfere with the DMX signals from the controller.
Auto Programs
Sound-Active
Display Timeout
1. Press <MENU> repeatedly until Aut shows on the display.
2. Press <ENTER> and Aut0–5 will show on the display.
3. Use <UP> or <DOWN> to select the desired program.
4. Press <ENTER> and S. 01–99 will show on the display.
5. Use <UP> or <DOWN> to increase or decrease the program speed.
1. Press <MENU> repeatedly until Sou shows on the display.
2. Press <ENTER>. Soud will show on the display.
In Sound-Active mode, the product will only respond to low frequencies of music
(bass and drums).
1. Press <MENU> repeatedly until CoL shows on the display.
2. Press <ENTER> and CoLo will show on the display.
3. Press <ENTER> again and L.000–255 will show on the display.
4. Use <UP> or <DOWN> to increase or decrease the dimmer value.
5. Press <ENTER> and S. 0–8 will show on the display.
6. Use <UP> or <DOWN> to increase or decrease the strobe rate.
1. Press <MENU> until SYS shows on the display.
2. Press <ENTER> and LEdS, tESt, or rESt will show on the display.
3. Use <UP> or <DOWN> to select LEdS.
4. Press <ENTER> and on or oFF will show on the display.
5. Use <UP>or <DOWN> to select whether the display timeout should be on or oFF.
Test Mode
1. Press <MENU> until SYS shows on the display.
2. Press <ENTER> and LEdS, tESt, or rESt will show on the display.
3. Use <UP> or <DOWN> to select tESt.
.
Reset
4. Press
To reset the software of the LED Shadow™, do the following:
1. Press <MENU> until SYS shows on the display.
2. Press <ENTER> and LEdS, tESt, or rESt will show on the display.
3. Use <UP> or <DOWN> to select rESt.
LED Shadow™ User Manual Rev. 6 Page 11 of 16
IRC-6 Infrared
Remote
Control
The LED Shadow™ is c ompatible with the IRC-6 infrared remote control from Chauvet.
IRC-6 Operation
may have inadvertently activated Black Out.
Master/Slave
(the “master”) to control
s (the “slaves”) without the need of a
s will be set to operate in
s will operate in unison with the
s before connecting the master to the daisy
Never connect a DMX controller to a DMX string configured for Master/Slave
Make sure to point the IRC-6 directly at the receiver on the front of the product.
Auto Mode
To run Auto mode:
1. Press <AUTO> to activate Auto program 0.
2. Press <1>
– <5> to activate one of the other programs.
3. Use <+> or <–> to increase or decrease the program speed.
Sound-Active Mode
To turn on Sound-Active mode:
Press <SOUND> on the IRC-6.
Manual Control
To manually control the intensity level:
1. Press <MANUAL> or <UV> on the IRC-6.
2. Press <+> or <–> to increase or decrease the output level.
Strobe Mode
To activate Strobe mode:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
To deactivate the strobe, switch to another mode.
Black Out
To black out the LEDs:
Press <BLACK OUT> on the IRC-6.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC will not respond to any inputs when Black Out is activated. If the remote
does not respond when a button is pressed, try pressing <BLACK OUT>. You
All other buttons on the IRC-6 infrared remote control have no function with this
product.
The Master/Slave mode allows a single LED Shadow™ product
the actions of one or more LED Shadow™ product
Mode
DMX controller. The master product will be set to operate in either Automatic mode,
Sound-Active mode, or with the IRC-6, while the slave product
Slave mode. Once set and connected, the slave product
master product.
Configure the products as indicated below .
Slave products:
1. Press <MODE> until SLA shows on the display.
2. Press <ENTER> to accept. SLAV will show in the display.
3. Connect the DMX input of the first slave product to the DMX output of the mast er
product.
4. Connect the DMX input of the subsequent slave products to the DMX output of the
previous slave product.
5. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to run in Auto mode, Sound-Activ e mo de, or with the IRC-6.
2. Make the master product the first product in the DMX daisy chain.
• Configure all the slave product
chain.
•
operation because the controller may interfere with the signals from the master .
• Do not connect more than 31 slaves to the master.
Page 12 of 16 LED Shadow™ User Manual Rev. 6
Product
up reduces light output performance and can cause overheating. This can lead
mechanical wear. To maintain optimum
s at least twice a month.
However, be aware that usage and environmental conditions could be contributing factors
5. MAINTENANCE
Dust build-
Maintenance
to reduction of the light source’s life and/or
performance and minimize wear, clean your lighting product
to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust
collected on the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning
tissue.
6. Softly drag any dirt or grime to the outside of the transparent surfa ce.
7. Gently polish the transpar ent s urfac es until they are free of haze and lint.
Always dry the transparent surfaces carefully af ter cleaning them.
LED Shadow™ User Manual Rev. 6 Page 13 of 16
Dimensions and
Length
Width
Height
Weight
14 in (356 mm)
9.8 in (248 mm)
6.5 in (165 mm)
4.9 lb (2.2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
12 W
11 W
Operating Current
0.1 A
0.1 A
Power linking current
(products)
Fuse
F 1 A, 250 V
F 1 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
0.25 W
100,000 hours
Color
Quantity
Current
UV
192
20 mA
Photometrics
Parameter
Coverage Angle
28°
Wavelength
405 nm
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
3-pin XLR 3
Ordering
Product Name
Item Code
UPC Number
LED Shadow™
10031085
781462214333
6. TECHNICAL SPECIFICATIONS
Weight
8 A (43 products) 8 A (74 products)
Page 14 of 16 LED Shadow™ User Manual Rev. 6
R
In case you need to get support or return a product:
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
products to them. Visit our website www.chauvetlighting.com for contact details.
Call the corresponding Chauvet Technical Support office and request a Return
returned without an RMA number.
Before sending the product, clearly write the following information on a piece of paper
recommended.
ETURNS
• If you are located in the U.S., contact Chauvet World Headquarters.
• If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
• If you are located in Mexico, contact Chauvet Mexico.
• If you are located in Benelux, contact Chauvet Europe BVBA.
• If you are located in any other country, DO NOT contact Chauvet. Instead, contact
your local distributor. See www.chauvetlighting.com for distributors outside the U.S.,
UK, Ireland, Mexico, or Benelux.
distributor of record and follow their instructions on how to return Chauvet
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
Send the merchandise prepaid, in its original box, and with its original packing and
accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
and place it inside the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).
LED Shadow™ User Manual Rev. 6 Page 15 of 16
C
WORLD HEADQUARTERS - Chauvet
General Information
Toll free: (800) 762-1084
Technical Support
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd.
General Information
Fax: +44 (0)1773 511110
Technical Support
MEXICO - Chauvet Mexico
General Information
Voice: +52 (728) 285-5000
Technical Support
CHAUVET EUROPE - Chauvet Europe BVBA
General Information
Voice: +32 9 388 93 97
Technical Support
contact your dealer. Follow their
instructions to request support or to return a product. Visit our website for contact details.
ONTACT US
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: (954) 577-4455
Fax: (954) 929-5560
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0)1773 511115
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: (954) 577-4455 (Press 4)
Fax: (954) 756-8015
Email: tech@chauvetlighting.com
Email: uktech@chauvetlighting.com
World Wide Web www.chauvetlighting.co.uk
Email: servicio@chauvet.com.mx
World Wide Web www.chauvet.com.mx
Email: Eutech@chauvetlighting.eu
World Wide Web www.chauvetlighting.eu
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux
Page 16 of 16 LED Shadow™ User Manual Rev. 6
Loading...